QuickSpecs
HPE FlexFabric 5700 Switch Series
Overview
1
HPE FlexFabric 5700 Switch Series
Models
HPE FlexFabric 5700 40XG 2QSFP+ Switch
JG896A
HPE FlexFabric 5700 48G 4XG 2QSFP+ Switch
JG894A
HPE FlexFabric 5700 32XGT 8XG 2QSFP+ Switch
JG898A
Key features
•
Product overview
The HPE Flex Fabric 5700 Switch Series is a family of high-performance, high-density, ultra-low-latency, top-of-rack (ToR)
switches that is part of the Hewlett Packard Enterprise (HPE) FlexNetwork architecture's HPE FlexFabric solution.
Ideally suited for deployment at the server access layer of large enterprise data centers, the
to provi
server traffic, customers now require ToR switch innovations that will meet their needs for higher
convergence of Ethernet and storage traffic, the capability to handle virtual environments, and ultra
device.
Features and benefits
Quality of Service (QoS)
Data center optimized
also be configured as four 10GbE ports by using a 40-GbE-to-10GbE splitter cable
Cut-through with low latency and wire speed
• HPE Intelligent Resilient Fabric (IRF) for virtualization and two-tier architectures
• High 1 GbE/10GbE ToR port density with 40 GbE uplinks
• Layer 2 and Light Layer 3 features with Static Routing and RIP
• Convergence-ready with DCB, FCoE, and TRILL
HPE 5700 Switch Series is positioned
de a cost-effective solution that is still powerful enough to handle the increase in virtualized applications and server-to-
-performance server connectivity,
-low-latency all in a single
• Powerful QoS features
- Flexible classification
Flow classification based on source MAC, destination MAC, Source IP (IPv4/IPv6), destination IP, port, protocol
and VLAN.
- Feature queue scheduling
• Flexible high port density
the HPE 5700 Switch Series enables scaling of the server edge with 1 GbE and 10GbE ToR deployments to new heights
with high-density 32 and 48-port solutions delivered in a 1RU design; the high server port density is backed by 40 GbE
QSFP+ uplinks to deliver the availability of needed bandwidth for demanding applications; each 40 GbE QSFP+ port can
provides support for Strict Priority (SP), Weighted Deficit Round Robin (WDRR), Weighted Fair Queuing (WFQ),
SP+WDRR, SP+WFQ. Supports Explicit Congestion Notification (ECN), and Weighted Random Early Detection
(WRED)
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Overview
2
• High-performance switching
lability and supports
ual Bridging with Virtual Ethernet Port Aggregator (EVB/VEPA) provides connectivity into the virtual environment for
performance remote backup
Software
Manageability
facilitate centralized discovery, monitoring, and secure management of networking devices
cut-through and nonblocking architecture delivers low latency (~1.5 microsecond for 10GbE) for very demanding
enterprise applications; the switch delivers high-performance switching capacity and wire-speed packet forwarding
• Higher scalability
Hewlett Packard Enterprise (HPE) Intelligent Resilient Framework (IRF) technology simplifies the architecture of server
access networks; up to nine HPE 5700 switches can be combined to deliver unmatched scalability of virtualized access
layer switches and flatter two-tier networks using IRF, which reduces cost and complexity. In addition, support for IRF as a
fabric will enable the 5700 Series to scale up to 30 switches as one virtualized device.
• Advanced modular operating system
Comware v7 software's modular design and multiple processes bring native high stability, independent process
monitoring, and restart; the OS also allows individual software modules to be upgraded for higher avai
enhanced serviceability functions like hitless software upgrades with single-chassis ISSU
• TRILL and EVB/VEPA
Transparent Interconnection of Lots of Links (TRILL) is supported to increase the scale of enterprise data centers; Edge
Virt
a data center-ready environment
• Reversible airflow
enhanced for data center hot-cold aisle deployment with reversible airflow—for either front-to-back or back-to-front
airflow
• Redundant fans and power supplies
1+1 internal redundant and hot-pluggable power supplies and dual fan trays enhance reliability and availability
• Lower OPEX and greener data center
provide reversible airflow and advanced chassis power management
• Data Center Bridging (DCB) protocols
provides support for IEEE 802.1Qbb Priority Flow Control (PFC) and Data Center Bridging Exchange (DCBX) for
converged applications
• FCoE support
provides support for Fibre Channel over Ethernet (FCoE) including FCF, Transit and NPV.
• Jumbo frames
with frame sizes of up to 10,000 bytes on Gigabit Ethernet and 10-Gigabit ports, allows highand disaster-recovery services to be enabled
• OpenFlow
• Full-featured console
• Troubleshooting
• Multiple configuration files
• sFlow (RFC 3176)
• SNMP v1, v2c and v3
-defined networking
supports OpenFlow 1.0 and 1.3 specifications to enable SDN by allowing separation of the data (packet forwarding) and
control (routing decision) path
provides complete control of the switch with a familiar CLI
- Ingress and egress port monitoring
enable network problem solving
- Traceroute and ping
enable testing of network connectivity
allow multiple configuration files to be stored to a flash image
provides wire-speed traffic accounting and monitoring
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Overview
3
• Out-of-band interface
Resiliency and high availability
Layer 2 switching
Local Forwarding First,
isolates management traffic from user data plane traffic for complete isolation and total reachability, no matter what
happens in the data plane
• Remote configuration and management
is available through a secure command-line interface (CLI) over Telnet and SSH; Role-Based Access Control (RBAC)
provides multiple levels of access; Configuration Rollback and multiple configurations on the flash provide ease of
operation; remote visibility is provided with sFlow and SNMP v1/v2/v3, and is fully supported in HPE Intelligent
Management Center (IMC)
• ISSU and hot patching
provides hitless software upgrades with single-unit In Services Software Upgrade (ISSU) and hitless patching of the
modular operating system
• Autoconfiguration
provides automatic configuration via DHCP autoconfiguration, NETCONF and Python Scripting
• Network Time Protocol (NTP) and Secure Network Time Protocol (SNTP)
synchronize timekeeping among distributed time servers and clients; keep consistent timekeeping among all clockdependent devices within the network so that the devices can provide diverse applications based on the consistent time.
Precision Time Protocol (PTP) RFC 1855 Compliant
• HPE Intelligent Resilient Fabric (IRF) technology
enables an HPE FlexFabric to deliver resilient, scalable, and secured data center networks for physical and virtualized
environments; groups up to nine HPE 5700 switches in an IRF configuration, allowing them to be configured and
managed as a single switch with a single IP address; simplifies ToR deployment and management, reducing data center
deployment and operating expenses
• IEEE 802.1w Rapid Convergence Spanning Tree Protocol
increases network uptime through faster recovery from failed links
• IEEE 802.1s Multiple Spanning Tree
provides high link availability in multiple VLAN environments by allowing multiple spanning trees
• Hitless patch upgrades
allows patches and new service features to be installed without restarting the equipment, increasing network uptime and
facilitating maintenance
• Device Link Detection Protocol (DLDP)
monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected, preventing loops in STPbased networks
• Address Resolution Protocol (ARP)
supports static, dynamic, and reverse ARP and ARP proxy
• Flow Control
IEEE 802.3x Flow Control provides intelligent congestion management via PAUSE frames
• Ethernet Link Aggregation
provides IEEE 802.3ad Link Aggregation of up to 128 groups of 16 ports; support for LACP, LACP
and LACP Short-time provides a fast, resilient environment that is ideal for the data center
• Spanning Tree Protocol (STP)
STP (IEEE 802.1D), Rapid STP (RSTP, IEEE 802.1w) and Multiple STP (MSTP) IEEE 802.1s)
• VLAN support
provides support for 4,094 VLANs based on port. VLAN Mapping, Q-in-Q and Selective Q-in-Q
• IGMP support
provides support for IGMP Snooping v1/v2/v3, PIM Snooping, MLD snooping v1/v2 and IPv6 PIM Snooping
• DHCP support at Layer 2
provides full DHCP Snooping support for DHCP Snooping Option 82, DHCP Relay Option 82, DHCP Snooping Trust, and
DHCP Snooping Item Backup
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Overview
4
Layer 3 services
allows detection
Layer 3 routing
Additional information
Management
happens in the data plane
• Address Resolution Protocol (ARP)
determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP
of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a
Layer 2 network
• Dynamic Host Configuration Protocol (DHCP)
simplifies the management of large IP networks and supports client and server; DHCP Relay enables DHCP operation
across subnets
• Operations, administration and maintenance (OAM) support
provides support for Connectivity Fault Management (IEEE 802.1AG) and Ethernet in the First Mile (IEEE 802.3AH);
provides additional monitoring that can be used for fast fault detection and recovery
• Equal-Cost Multipath (ECMP)
enables multiple equal-cost links in a routing environment to increase link redundancy and scale bandwidth
• Layer 3 IPv4 routing
provides routing of IPv4 at media speed; supports static routes, RIP and RIPv2
• Static IPv6 routing
provides simple manually configured IPv6 routing
• Dual IP stack
maintains separate stacks for IPv4 and IPv6 to ease the transition from an IPv4-only network to an IPv6-only network
design
• Bidirectional Forwarding Detection (BFD)
enables link connectivity monitoring and reduces network convergence time for RIP, OSPF, BGP, IS-IS, VRRP, MPLS, and
IRF
• Layer 3 IPv6 routing
provides routing of IPv6 at media speed; supports static routing and RIPng
• Green IT and power
improves energy efficiency through the use of the latest advances in silicon development; shuts off unused ports and
utilizes variable-speed fans, reducing energy costs
• Low maximum power consumption
is rated to have one of the lowest power usages in the industry by Miercom independent tests
• USB support
- File copy
• Multiple configuration files
stores easily to the flash image
• SNMPv1, v2c, and v3
facilitate centralized discovery, monitoring, and secure management of networking devices
• Network Time Protocol (NTP)
synchronizes timekeeping among distributed time servers and clients; keeps timekeeping consistent among all clockdependent devices within the network so that the devices can provide diverse applications based on the consistent time
• Out-of-band interface
isolates management traffic from user data plane traffic for complete isolation and total reachability, no matter what
allows users to copy switch files to and from a USB flash drive
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Overview
5
• Port mirroring
pact on network performance; this
provides local and remote logging of events via SNMP (v2c and v3) and syslog; provides log throttling and log filtering to
restricts access to critical configuration commands; offers multiple privilege levels with password protection; ACLs provide
Security
provide IP Layer 3 filtering based on source/destination IP address/subnet and source/destination TCP/UDP port number
Convergence
enables traffic on a port to be simultaneously sent to a network analyzer for monitoring
• Remote configuration and management
is available through a command-line interface (CLI)
• IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by
network management applications
• sFlow (RFC 3176)
provides scalable ASIC-based wirespeed network monitoring and accounting with no im
allows network operators to gather a variety of sophisticated network statistics and information for capacity planning and
real-time network monitoring purposes
• Command authorization
leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login; an audit trail
documents activity
• Dual flash images
provides independent primary and secondary operating system files for backup while upgrading
• Command-line interface (CLI)
provides a secure, easy-to-use CLI for configuring the module via SSH or a switch console; provides direct real-time
session visibility
• Logging
reduce the number of log events generated
• Management interface control
provides management access through a modem port and terminal interface, as well as in-band and out-of-band Ethernet
ports; provides access through terminal interface, Telnet, or secure shell (SSH)
• Industry-standard CLI with a hierarchical structure
reduces training time and expenses, and increases productivity in multivendor installations
• Management security
Telnet and SNMP access; local and remote syslog capabilities allow logging of all access
• Information center
provides a central repository for system and network information; aggregates all logs, traps, and debugging information
generated by the system and maintains them in order of severity; outputs the network information to multiple channels
based on user-defined rules
• Network management
HPE Intelligent Management Center (IMC) centrally configures, updates, monitors, and troubleshoots
• Remote intelligent mirroring
mirrors ingress/egress ACL-selected traffic from a switch port or VLAN to a local or remote switch port anywhere on the
network
• Access control lists (ACLs)
• RADIUS/TACACS+
eases switch management security administration by using a password authentication server
• Secure shell
encrypts all transmitted data for secure remote CLI access over IP networks
• IEEE 802.1X and RADIUS network logins
controls port-based access for authentication and accountability
• Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Overview
6
• LLDP-MED (Media Endpoint Discovery)
defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure
Warranty and support
; for details on the software releases
network devices such as IP phones
• 1-year warranty
see http://www.hpe.com/networking/warrantysummary
product purchase.
• Software releases
to find software for your product, refer to http://www.hpe.com/networking/support
available with your product purchase, refer to http://www.hpe.com/networking/warrantysummary
for warranty and support information included with your
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Configuration
7
Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are
not part of a CTO or Rack
Standard Switch Enclosures
HPE FlexFabric 5700 48G 4XG 2QSFP+ Switch
JG894A
• 48 RJ45 10/100/1000Base-T Copper ports
See
Configuration
HPE FlexFabric 5700 40XG 2QSFP+ Switch
JG896A
• 40 - 1/10GbE SFP+ ports (min=0 \ max=40 SFP+ Transceivers)
See Configuration
HPE FlexFabric 5700 32XGT 8XG 2QSFP+ Switch
JG898A
• 32 RJ45 1/10GBase-T Copper ports
See Configuration
Configuration Rules
Note 1
The following Transceivers install into this Switch's SFP+ Ports:
HPE X120 1G SFP LC LH40 1550nm Transceiver
JD062A
HPE X120 1G SFP LC BX 10-U Transceiver
JD098B
HPE X120 1G SFP LC BX 10-D Transceiver
JD099B
HPE X120 1G SFP LC SX Transceiver
JD118B
HPE X120 1G SFP LC LX Transceiver
JD119B
HPE X120 1G SFP RJ45 T Transceiver
JD089B
HPE X125 1G SFP LC LH40 1310nm Transceiver
JD061A
HPE X125 1G SFP LC LH70 Transceiver
JD063B
HPE X130 10G SFP+ LC SR Transceiver
JD092B
HPE X130 10G SFP+ LC LR Transceiver
JD094B
HPE X130 10G SFP+ LC SR Data Center Transceiver
JL437A
HPE X130 10G SFP+ LC LR Data Center Transceiver
JL439A
HPE X130 10G SFP+ LC ER 40km Transceiver
JG234A
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
JD095C
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
JD096C
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
JD097C
-Shippable solution.
• 4 - 1/10GbE SFP+ ports (min=0 \ max=4 SFP+ Transceivers)
• 2 - 40GbE QSFP ports (min=0 \ max=2 QSFP Transceivers)
• 1 Power Supply Required
• 1U - Height
NOTE:1, 2, 4
• 2 - 40GbE QSFP ports (min=0 \ max=2 QSFP Transceivers)
• 1 Power Supply Required
• 1U - Height
• 8 - 1/10GbE SFP+ ports (min=0 \ max=8 SFP+ Transceivers)
• 2 - 40GbE QSFP ports (min=0 \ max=2 QSFP Transceivers)
• 1 Power Supply Required
• 1U - Height
NOTE:1, 2, 4, 6
NOTE:1, 2, 4, 6
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Configuration
8
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JG081C
HPE FlexNetwork X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable
JC784C
Note 2
The following Transceivers install into this switch's QSFP+ Ports:
HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver
JG661A
HPE X140 40G QSFP+ LC BiDi 100m MM Transceiver
JL251A
HPE X140 40G QSFP+ MPO SR4 Transceiver
JG325B
HPE X140 40G QSFP+ LC LR4L 2km SM Transceiver
JL286A
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver
JG709A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
JG326A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
JG327A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
JG328A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
JG329A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable
JG330A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
JG331A
Note 4
The following 40G Transceivers install into this switch:
HPE X2A0 40G QSFP+ to QSFP+ 7m Active Optical Cable
JL287A
HPE X2A0 40G QSFP+ to QSFP+ 10m Active Optical Cable
JL288A
HPE X2A0 40G QSFP+ to QSFP+ 20m Active Optical Cable
JL289A
Note 6
The following 40G Transceiver install into this switch:
HPE X140 40G QSFP+ LC ER4 40km SM Transceiver
JL306A
Remarks
OCA Blue Note - The following 1G XCVR's are only supported on PHY switch ports:
HPE X125 1G SFP LC LH40 1310nm Transceiver
JD061A
HPE X120 1G SFP LC LH40 1550nm Transceiver
JD062A
HPE X125 1G SFP LC LH70 Transceiver
JD063B
OCA Blue Note - The following 10G XCVR is only supported on the PHY switch ports for the HP
FF 5700-32XGT-8XG-2QSFP+ Switch (JG898A).
HPE X130 10G SFP+ LC ER 40km Transceiver
JG234A
OCA Only Model Selection Form HPE Offering > DataCenter Networking > FlexFabric Switches
5700 Switch Series
Box Level Integration CTO Models
CTO Solution SKU
HPE FlexFabric 57xx Configure to order Switch Solution
JH061A
• SSP trigger SKU
CTO Switch Chassis
HPE FlexFabric 5700 48G 4XG 2QSFP+ Switch
JG894A
- Access:
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Configuration
9
• 48 RJ45 10/100/1000Base-T Copper ports
See Configuration
HPE FlexFabric 5700 40XG 2QSFP+ Switch
JG896A
•
See Configuration
HPE FlexFabric 5700 32XGT 8XG 2QSFP+ Switch
JG898A
• 32 RJ45 1/10GBase-T Copper ports
See Configuration
Configuration Rules
Note 1
The following 40G Transceivers install into this switch: (Use #0D1 or #B01 quoted to switch if switch is CTO) - if
applicable
HPE X120 1G SFP LC LH40 1550nm Transceiver
JD062A
HPE X120 1G SFP LC BX 10-U Transceiver
JD098B
HPE X120 1G SFP LC BX 10-D Transceiver
JD099B
HPE X120 1G SFP LC SX Transceiver
JD118B
HPE X120 1G SFP LC LX Transceiver
JD119B
HPE X120 1G SFP RJ45 T Transceiver
JD089B
HPE X125 1G SFP LC LH40 1310nm Transceiver
JD061A
HPE X125 1G SFP LC LH70 Transceiver
JD063B
HPE X130 10G SFP+ LC SR Transceiver
JD092B
HPE X130 10G SFP+ LC LR Transceiver
JD094B
HPE X130 10G SFP+ LC SR Data Center Transceiver
JL437A
HPE X130 10G SFP+ LC LR Data Center Transceiver
JL439A
HPE X130 10G SFP+ LC ER 40km Transceiver
JG234A
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
JD095C
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
JD096C
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
JD097C
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JG081C
HPE FlexNetwork X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable
JC784C
Note 2
The following Transceivers install into this switch's QSFP+ Ports: (Use #0D1 or #B01 if switch is CTO)
HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver
JG661A
HPE X140 40G QSFP+ LC BiDi 100m MM Transceiver
JL251A
HPE X140 40G QSFP+ MPO SR4 Transceiver
JG325B
HPE X140 40G QSFP+ LC LR4L 2km SM Transceiver
JL286A
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver
JG709A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
JG326A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
JG327A
• 4 - 1/10GbE SFP+ ports (min=0 \ max=4 SFP+ Transceivers)
• 2 - 40GbE QSFP ports (min=0 \ max=2 QSFP Transceivers)
• 1 Power Supply Required
• 1U - Height
40 - 1/10GbE SFP+ ports (min=0 \ max=40 SFP+ Transceivers)
• 2 - 40GbE QSFP ports (min=0 \ max=2 QSFP Transceivers)
• 1 Power Supply Required
• 1U - Height
• 8 - 1/10GbE SFP+ ports (min=0 \ max=8 SFP+ Transceivers)
• 2 - 40GbE QSFP ports (min=0 \ max=2 QSFP Transceivers)
• 1 Power Supply Required
• 1U - Height
NOTE:1, 2, 4, 5
NOTE:1, 2, 4, 5, 7
NOTE:1, 2, 4, 5, 7
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Configuration
10
HPE FlexNetwork X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
JG328A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
JG329A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable
JG330A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
JG331A
Note 4
If the Switch Chassis is to be Box Level Factory Integrated (CTO), Then the #0D1 is required on the Switch Chassis
and integrated to the JH061A
SSP)
Note 5
The following 40G Transceivers install into this switch: (Use #0D1 or #B01 quoted to switch if switch is CTO) - if
applicable
HPE X2A0 40G QSFP+ to QSFP+ 7m Active Optical Cable
JL287A
HPE X2A0 40G QSFP+ to QSFP+ 10m Active Optical Cable
JL288A
HPE X2A0 40G QSFP+ to QSFP+ 20m Active Optical Cable
JL289A
Note 7
The following 40G Transceiver install into this switch: (Use #0D1 or #B01 if switch is CTO)
HPE X140 40G QSFP+ LC ER4 40km SM Transceiver
JL306A
Remarks:
OCA Blue Note - The following 1G XCVR's are only supported on PHY switch ports:
HPE X125 1G SFP LC LH40 1310nm Transceiver
JD061A
HPE X120 1G SFP LC LH40 1550nm Transceiver
JD062A
HPE X125 1G SFP LC LH70 Transceiver
JD063B
OCA Blue Note - The following 10G XCVR is only supported on the PHY switch ports for the HPE
FF 5700-32XGT-8XG-2QSFP+ Switch (JG898A).
HPE X130 10G SFP+ LC ER 40km Transceiver
JG234A
Clic UNB - If an option is ordered with #0D1/#B01, then the switch must have #0D1 option.
Rack Level Integration CTO Models
Standard Switch Chassis
HPE FlexFabric 5700 48G 4XG 2QSFP+ Switch
JG894A
• 48 RJ45 10/100/1000Base-T Copper ports
See Configuration
HPE FlexFabric 5700 40XG 2QSFP+ Switch
JG896A
•
• 1U - Height
See Configuration
HPE FlexFabric 5700 32XGT 8XG 2QSFP+ Switch
JG898A
- HPE FlexFabric 57xx Configure to order Switch Solution. (Min 1/Max 1 Switch per
• 4 - 1/10GbE SFP+ ports (min=0 \ max=4 SFP+ Transceivers)
• 2 - 40GbE QSFP ports (min=0 \ max=2 QSFP Transceivers)
• 1 Power Supply Required
• 1U - Height
40 - 1/10GbE SFP+ ports (min=0 \ max=40 SFP+ Transceivers)
• 2 - 40GbE QSFP ports (min=0 \ max=2 QSFP Transceivers)
• 1 Power Supply Required
NOTE: 1, 2, 4, 11
NOTE: 1, 2, 4, 6,
11
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Configuration
11
•
• 1U - Height
See Configuration
Configuration Rules
Note 1
The following Transceivers install into this Switch's SFP+ Ports:
HPE X120 1G SFP LC LH40 1550nm Transceiver
JD062A
HPE X120 1G SFP LC BX 10-U Transceiver
JD098B
HPE X120 1G SFP LC BX 10-D Transceiver
JD099B
HPE X120 1G SFP LC SX Transceiver
JD118B
HPE X120 1G SFP LC LX Transceiver
JD119B
HPE X120 1G SFP RJ45 T Transceiver
JD089B
HPE X125 1G SFP LC LH40 1310nm Transceiver
JD061A
HPE X125 1G SFP LC LH70 Transceiver
JD063B
HPE X130 10G SFP+ LC SR Transceiver
JD092B
HPE X130 10G SFP+ LC LR Transceiver
JD094B
HPE X130 10G SFP+ LC SR Data Center Transceiver
JL437A
HPE X130 10G SFP+ LC LR Data Center Transceiver
JL439A
HPE X130 10G SFP+ LC ER 40km Transceiver
JG234A
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
JD095C
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
JD096C
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
JD097C
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JG081C
HPE FlexNetwork X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable
JC784C
Note 2
The following Transceivers install into this switch's QSFP+ Ports: (Use #0D1 or #B01 if switch is CTO)
HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver
JG661A
HPE X140 40G QSFP+ LC BiDi 100m MM Transceiver
JL251A
HPE X140 40G QSFP+ MPO SR4 Transceiver
JG325B
HPE X140 40G QSFP+ LC LR4L 2km SM Transceiver
JL286A
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver
JG709A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
JG326A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
JG327A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
JG328A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
JG329A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable
JG330A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
JG331A
Note 4
The following 40G Transceivers install into this switch: (Use #0D1 or #B01 quoted to switch if switch is CTO) - if
applicable
HPE X2A0 40G QSFP+ to QSFP+ 7m Active Optical Cable
JL287A
HPE X2A0 40G QSFP+ to QSFP+ 10m Active Optical Cable
JL288A
HPE X2A0 40G QSFP+ to QSFP+ 20m Active Optical Cable
JL289A
Note 6
The following 40G Transceiver install into this switch: (Use #0D1 or #B01 if switch is CTO)
HPE X140 40G QSFP+ LC ER4 40km SM Transceiver
JL306A
32 RJ45 1/10GBase-T Copper ports
• 8 - 1/10GbE SFP+ ports (min=0 \ max=8 SFP+ Transceivers)
• 2 - 40GbE QSFP ports (min=0 \ max=2 QSFP Transceivers)
• 1 Power Supply Required
NOTE: 1, 2, 4, 6,
11
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Configuration
12
Note 11
If HPE CTO Switch Chassis is selected for Rack Level Integration, Then the Switch needs to integrate (with #0D1) to
the HPE Rack.
Remarks:
OCA Blue Note - The following 1G XCVR's are only supported on PHY switch ports:
HPE X125 1G SFP LC LH40 1310nm Transceiver
JD061A
HPE X120 1G SFP LC LH40 1550nm Transceiver
JD062A
HPE X125 1G SFP LC LH70 Transceiver
JD063B
OCA Blue Note - The following 10G XCVR is only supported on the PHY switch ports for the HP FF 5700-32XGT8XG-2QSFP+ Switch (JG898A).
HPE X130 10G SFP+ LC ER 40km Transceiver
JG234A
Clic UNB - If an option is ordered with #0D1/#B01, then the switch must have #0D1 option.
Enter the following menu selections as integrated to the CTO Model X server above if order is factory built.
Transceivers
SFP Transceivers
HPE X120 1G SFP LC LH40 1550nm Transceiver
JD062A
HPE X120 1G SFP LC BX 10-U Transceiver
JD098B
HPE X120 1G SFP LC BX 10-D Transceiver
JD099B
HPE X120 1G SFP LC SX Transceiver
JD118B
HPE X120 1G SFP LC LX Transceiver
JD119B
HPE X120 1G SFP RJ45 T Transceiver
JD089B
HPE X125 1G SFP LC LH40 1310nm Transceiver
JD061A
HPE X125 1G SFP LC LH70 Transceiver
JD063B
SFP+ Transceivers
HPE X130 10G SFP+ LC SR Transceiver
JD092B
HPE X130 10G SFP+ LC LR Transceiver
JD094B
HPE X130 10G SFP+ LC ER 40km Transceiver
JG234A
HPE X130 10G SFP+ LC SR Data Center Transceiver
JL437A
HPE X130 10G SFP+ LC LR Data Center Transceiver
JL439A
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
JD095C
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
JD096C
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
JD097C
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JG081C
HPE FlexNetwork X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable
JC784C
QSFP+ Transceivers
HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver
JG661A
HPE X140 40G QSFP+ LC BiDi 100m MM Transceiver
JL251A
HPE X140 40G QSFP+ MPO SR4 Transceiver
JG325B
HPE X140 40G QSFP+ LC LR4L 2km SM Transceiver
JL286A
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Configuration
13
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver
JG709A
HPE X140 40G QSFP+ LC ER4 40km SM Transceiver
JL306A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
JG326A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
JG327A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
JG328A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
JG329A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable
JG330A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
JG331A
HPE X2A0 40G QSFP+ to QSFP+ 7m Active Optical Cable
JL287A
HPE X2A0 40G QSFP+ to QSFP+ 10m Active Optical Cable
JL288A
HPE X2A0 40G QSFP+ to QSFP+ 20m Active Optical Cable
JL289A
Internal Power Supplies
System (std 0 // max 2) User Selection (min 1 // max 2) per switch enclosure
HPE A58x0AF Back (Power Side) to Front (Port Side) Airflow 300W AC Power Supply
JG900A
•
See Configuration
PDU Cable NA/MEX/TW/JP
JG900A#B2B
• C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
JG900A#B2C
• C15 PDU Jumper Cord (ROW)
High Volt Switch/Router to Wall Power Cord
JG900A#B2E
• NEMA L6-20P Cord (NA/MEX/JP/TW)
HPE A58x0AF Back (Power Side) to Front (Port Side) Airflow 300W DC Power Supply
JG901A
See Configuration
NOTE:
HPE 58x0AF 650W AC Power Supply
JC680A
See Configuration
NOTE: 1, 2, 4
PDU Cable NA/MEX/TW/JP
JC680A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
JC680A#B2C
C15 PDU Jumper Cord (ROW)
HPE FlexFabric Switch 650W 48V Hot Plug NEBS-compliant DC Power Supply
JH336A
See Configuration
NOTE:
Configuration Rules:
Note 1
If 2 power supplies are selected they must be the same SKU number.
includes 1 x c13, 300w
NOTE: 1, 2, 3
• includes 1 x c13, 300w
1, 3, 5
1, 4
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Configuration
14
Note 2
Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) or #B2E. (See
Localization Menu)
REMARK: When Switches/Routers are Factory Racked, Then
option on the Switches/Routers.
Note 3
This power supply is only supported on JG894A and JG896A.
Note 4
This power supply is only supported on JG894A and JG898A.
Note 5
Watson Only - Add "(NEBS)" after the description on the PS table.
Remarks
Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord
ROW.
Switch/Router/Power Supply to Wall Power Cord
CTO)
High Volt Switch/Router/Power Supply to Wall Power Cord
Taiwan, and Japan)
NOTE* Switches JG894A and JG896A should default selection of Power Supply as JG900A, but allow selection of
JG901A, and JC680A if applicable.
Switch Options
Fan Trays
System (std 0 // max 2) User Selection (min 2 // max 2) per switch
HPE 58x0AF Back (Power Side) to Front (Port Side) Airflow Fan Tray
JC682A
See Configuration
NOTE: 1, 2
HPE 58x0AF Front (Port Side) to Back (Power Side) Airflow Fan Tray
JC683A
See Configuration
NOTE:
HPE X711 Front (Port Side) to Back (Power Side) Airflow High Volume Fan Tray
JG552A
See Configuration
NOTE: 1, 3
HPE X712 Back (Power Side) to Front (Port Side) Airflow High Volume Fan Tray
JG553A
See Configuration
NOTE:
Configuration Rules
Note 1
Fan Trays cannot be mixed in the same switch enclosure
Note 2
This Fan Tray is only supported on JG894A and JG896A.
#B2B, or #B2C should be the Defaulted Power Cable
- #B2B in North America, Mexico, Taiwan, and Japan or #B2C
(Configurators Default B2B or B2C for Rack Level CTO)
- Localized Option (Configurators Default for BTO and Box Level
- #B2E Option. (Offered only in North America, Mexico,
1, 2
1, 3
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Configuration
15
Note 3
This Fan Tray is only supported on JG898A.
Remarks:
Configurator Informational Text:
If there is any empty space below the switch in a rack when using Back to Front Fan Trays, JG553A, the rack will
receive an Air Plenum kit that takes up 1U of additional space in the rack. The Air Plenum kit is not
configured racks. This only applies for CTO Rack Level Integration. The Air Plenum Kit is a non
brought in automatically for CTO Factory Rack Level Integration.
required on fully
-saleable SKU, and is
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Technical Specifications
16
HPE FlexFabric 5700 40XG 2QSFP+ Switch (JG896A)
I/O ports and slots
40 fixed 1000/10000 SFP+ ports
2 QSFP+
Additional ports and
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
2 fan tray slots
The customer must order fan trays, as fan trays are not included with the switch. This system requires two
same
The system should not be operated with only one fan tray for more than 24 hours. The system should not
be operated without a fan tray for more than two minutes.
The system should not be operated outside of the temperature range of 32°F (0°C) to 113°F (45°C).
Failure to comply with these operating requirements may void the product warranty.
Physical characteristics
Dimensions
17.32(w) x 18.11(d) x 1.72(h) in (43.99 x 46 x 4.37 cm) (1U height)
Weight
22.05 lb (10 kg) shipping weight
Memory and processor
512 MB flash; Packet buffer size: 9 MB, 2 GB SDRAM
Performance
10 Gbps Latency
Throughput
up to 714.2 Mpps
Routing/Switching capacity
960 Gbps
Routing table size
128 entries (IPv4), 128 entries (IPv6))
MAC address table size
128000 entries
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative humidity
10% to 90%, noncondensing
Acoustic
Low-speed fan: 65.7 dB, High-speed fan: 70.6 dB
Electrical
Frequency
50/60 Hz
Voltage
100 - 240 VAC, rated
(depending on power supply chosen)
Maximum power rating
162 W
Idle power
90 W
Notes
Idle power is the actual power consumption of the device with no ports
all modules populated.
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950
Subchapter J; NOM; ROHS Compliance
Emissions
VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS CISPR 22 Class A; EN
61000
3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47,
Part 15) Class A
Immunity
Generic
ETSI EN 300 386 V1.3.3
EN
EN 55024:1998+ A1:2001 + A2:2003
slots
-direction airflow fan trays to function properly.
characteristics
< 1.5 µs (64-byte packets)
-48 to -60 VDC, rated
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure
with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and
-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR
-3-2:2006; EN 61000-3-
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Technical Specifications
17
ESD
EN 61000-4-2; IEC 61000-4-2
Radiated
EN 61000-4-3; IEC 61000-4-3
EFT/Burst
EN 61000-4-4; IEC 61000-4-4
Surge
EN 61000-4-5; IEC 61000-4-5
Conducted
EN 61000-4-6; IEC 61000-4-6
Power frequency magnetic
field
IEC 61000-4-8; EN 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11; IEC 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
IMC - Intelligent Management Center; command-line interface; out-of-band management; SNMP Manager;
Telnet; FTP
Services
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for
details on the service
times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexFabric 5700 48G 4XG 2QSFP+ Switch (JG894A)
I/O ports and slots
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASETX, IEEE 802.3ab Type 1000BASE
only
4 fixed 1000/10000 SFP+ ports
2 QSFP+
Additional ports and
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
2 fan tray slots
The customer must order fan trays, as fan trays are not included with the switch. This system requires two
same
The system should not be operated with only one fan tray for more than 24 hours. The system should not
be operated without a fan tray for more than two minutes.
The system should not be operated outside of the temper
Failure to comply with these operating requirements may void the product warranty.
Physical characteristics
Dimensions
17.32(w) x 18.11(d) x 1.72(h) in (43.99 x 46 x 4.37 cm) (1U height)
Weight
22.05 lb (10 kg) shipping weight
Memory and processor
512 MB flash; Packet buffer size: 9 MB, 2 GB SDRAM
Performance
10 Gbps Latency
< 1.5 µs (64-byte packets)
Throughput
up to 250 Mpps
Routing/Switching capacity
336 Gbps
Routing table size
128 entries (IPv4), 128 entries (IPv6)
MAC address table size
128000 entries
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative humidity
10% to 90%, noncondensing
Acoustic
Low-speed fan: 65.7 dB, High-speed fan: 70.6 dB
Frequency
50/60 Hz
-level descriptions and product numbers. For details about services and response
slots
-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full
-direction airflow fan trays to function properly.
ature range of 32°F (0°C) to 113°F (45°C).
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Technical Specifications
18
Voltage
100 - 240 VAC, rated
(depending on power supply chosen)
Maximum power rating
175 W
Idle power
115 W
Notes
Idle power is the actual power consumption of the device with no ports
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950
Subchapter J; NOM; ROHS Compliance
Emissions
VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS CISPR 22 Class A; EN
61000
3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47,
Part 15) Class A
Immunity
Generic
ETSI EN 300 386 V1.3.3
EN
EN 55024:1998+ A1:2001 + A2:2003
ESD
EN 61000-4-2; IEC 61000-4-2
Radiated
EN 61000-4-3; IEC 61000-4-3
EFT/Burst
EN 61000-4-4; IEC 61000-4-4
Surge
EN 61000-4-5; IEC 61000-4-5
Conducted
EN 61000-4-6; IEC 61000-4-6
Power frequency magnetic
field
IEC 61000-4-8; EN 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11; IEC 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
IMC - Intelligent Management Center; command-line interface; out-of-band management; SNMP Manager;
Telnet; FTP
Services
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for
details on the service
times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexFabric 5700 32XGT 8XG 2QSFP+ Switch (JG898A)
I/O ports and slots
32 RJ-45 1/10GBASE-T ports; Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
8 fixed 1000/10000 SFP+ ports
2 QSFP+
Additional ports and
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
2 fan tray slots
The customer must order fan trays, as fan trays are not included with the switch. This system requires two
same
fan tray for more than 24 hours. The system should not be operated without a fan tray for more than two
Electrical
characteristics
-48 to -60 VDC, rated
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure
with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and
all modules populated.
-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR
-3-2:2006; EN 61000-3-
slots
-level descriptions and product numbers. For details about services and response
-direction airflow fan trays to function properly. The system should not be operated with only one
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Technical Specifications
19
minutes.
The system should not be operated outside of the temperature range of 32°F (0°C) to 113°F (45°C).
Failure to comply with these operating requirements may void the product warranty.
Physical characteristics
Dimensions
17.32(w) x 25.98(d) x 1.72(h) in (43.99 x 66.0 x 4.37 cm) (1U height)
Weight
28.66 lb (13 kg) shipping weight
Memory and processor
512 MB flash; Packet buffer size: 9 MB, 2 GB SDRAM
Performance
10 Gbps Latency
< 1.5 µs (64-byte packets)
Throughput
up to 714.2 Mpps
Routing/Switching capacity
960 Gbps
Routing table size
128 entries (IPv4), 128 entries (IPv6)
MAC address table size
128000 entries
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative humidity
10% to 90%, noncondensing
Acoustic
Low-speed fan: 65.7 dB, High-speed fan: 70.6 dB
Electrical
Frequency
50/60 Hz
Voltage
100 - 240 VAC, rated
(depending on power supply chosen)
Maximum power rating
350 W
Idle power
150 W
Notes
Idle power is the actual power consumption of the device with no ports
all modules populated.
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950
Subchapter J; NOM; ROHS Compliance
Emissions
VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS CISPR 22 Class A; EN
61000
Directive 2004/108/EC; FCC (CFR 47,
Part 15) Class A
Immunity
Generic
ETSI EN 300 386 V1.3.3
EN
EN 55024:1998+ A1:2001 + A2:2003
ESD
EN 61000-4-2; IEC 61000-4-2
Radiated
EN 61000-4-3; IEC 61000-4-3
EFT/Burst
EN 61000-4-4; IEC 61000-4-4
Surge
EN 61000-4-5; IEC 61000-4-5
Conducted
EN 61000-4-6; IEC 61000-4-6
Power frequency magnetic
field
IEC 61000-4-8; EN 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11; IEC 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
IMC - Intelligent Management Center; command-line interface; out-of-band management; SNMP Manager;
Telnet; FTP
characteristics
-48 to -60 VDC, rated
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure
with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and
-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR
-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Technical Specifications
20
Services
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for
details on the service
times in your area, please contact your local Hewlett Packard Enterprise sales office.
Standards and protocols
Device management
RFC 1213 Management Information Base for
IPv6
Type 0 Routing Headers
-level descriptions and product numbers. For details about services and response
(applies to all products in
series)
RFC 1157 SNMPv1/v2c
RFC 1305 NTPv3
RFC 1591 DNS (client)
RFC 1902 (SNMPv2)
RFC 1908 (SNMP v1/2 Coexistence)
RFC 2573 (SNMPv3 Applications)
RFC 2576 (Coexistence between SNMP V1, V2,
V3)
Multiple Configuration Files
Multiple Software Images
SSHv1/SSHv2 Secure Shell
TACACS/TACACS+
General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1ag Service Layer OAM
IEEE 802.1D MAC Bridges
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1w Rapid Reconfiguration of Spanning
Tree
IEEE 802.3 Type 10BASE-T
IEEE 802.3ab 1000BASE-T Gigabit Ethernet over
twisted pair (10/100/1000 models only)
IEEE 802.3ad Link Aggregation Control Protocol
(LACP)
IEEE 802.3ae 10-Gigabit Ethernet
IEEE 802.3ag Ethernet OAM
IEEE 802.3ah Ethernet in First Mile over Point to
Point Fiber – EFMF
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 856 TELNET
RFC 868 Time Protocol
RFC 896 Congestion Control in IP/TCP
Internetworks R
RFC 950 Internet Standard Subnetting Procedure
RFC 1027 Proxy ARP
RFC 1058 RIPv1
RFC 1091 Telnet Terminal-Type Option
RFC 1141 Incremental updating of the Internet
checksum
RFC 1191 Path MTU discovery
RFC 2080 RIPng for IPv6
RFC 2460 IPv6 Specification
RFC 2461 IPv6 Neighbor Discovery
RFC 2462 IPv6 Stateless Address Autoconfiguration R
RFC 2463 ICMPv6
RFC 2464 Transmission of IPv6 over Ethernet
Networks
RFC 2563 ICMPv6
RFC 2711 IPv6 Router Alert Option
RFC 2767 Dual stacks IPv46 & IPv6
RFC 3315 DHCPv6 (client and relay)
RFC 4291 IP Version 6 Addressing Architecture
RFC 4862 IPv6 Stateless Address Autoconfiguration
RFC 5095 Deprecation of
in IPv6
MIBs
RFC 1213 MIB II
RFC 1907 SNMPv2 MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-Notification MIB
RFC 2573 SNMP-Target MIB
RFC 2574 SNMP USM MIB
RFC 2737 Entity MIB (Version 2)
RFC 3414 SNMP-User based-SM MIB
RFC 3415 SNMP-View based-ACM MIB
LLDP-EXT-DOT1-MIB
LLDP-EXT-DOT3-MIB
LLDP-MIB
Network management
RFC 3164 BSD syslog Protocol
QoS/CoS
IEEE 802.1p (CoS)
RFC 2475 DiffServ Architecture
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 3247 Supplemental Information for the New
Definition of the EF PHB (Expedited Forwarding
Per-Hop Behavior)
RFC 3260 New Terminology and Clarifications for
DiffServ
Security
Access Control Lists (ACLs)
SSHv2 Secure Shell
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Technical Specifications
21
Network Management of TCP/IP-based internets
ell (SSH) Transport Layer
RFC 1531 Dynamic Host Configuration Protocol
RFC 1541 DHCP
RFC 1591 DNS (client only)
RFC 1624 Incremental Internet Checksum
RFC 1723 RIP v2
RFC 1812 IPv4 Routing
RFC 2030 Simple Network Time Protocol (SNTP)
v4
RFC 2131 DHCP
RFC 2236 IGMP Snooping
RFC 2453 RIPv2
RFC 2581 TCP Congestion Control
RFC 2644 Directed Broadcast Control
RFC 2767 Dual Stacks IPv4 & IPv6
RFC 3046 DHCP Relay Agent Information Option
RFC 4250 The Secure Shell (SSH) Protocol
Assigned Numbers
RFC 4251 The Secure Shell (SSH) Protocol
Architecture
RFC 4252 The Secure Shell (SSH) Authentication
Protocol
RFC 4253 The Secure Sh
Protocol
RFC 4254 The Secure Shell (SSH) Connection
Protocol
RFC 4419 Diffie-Hellman Group Exchange for the
Secure Shell (SSH) Transport Layer Protocol
RFC 4594 Configuration Guidelines for DiffServ
Service Classes
RFC 4941 Privacy Extensions for Stateless
Address Autoconfiguration in IPv6
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Accessories
22
HPE FlexFabric 5700 Switch Series accessories
Transceivers
HPE X120 1G SFP LC LH40 1550nm Transceiver
JD062A
HPE X120 1G SFP LC BX 10-U Transceiver
JD098B
HPE X120 1G SFP LC BX 10-D Transceiver
JD099B
HPE X120 1G SFP LC LX Transceiver
JD119B
HPE X120 1G SFP RJ45 T Transceiver
JD089B
HPE X120 1G SFP LC SX Transceiver
JD118B
HPE X125 1G SFP LC LH40 1310nm Transceiver
JD061A
HPE X125 1G SFP LC LH70 Transceiver
JD063B
HPE X130 10G SFP+ LC SR Transceiver
JD092B
HPE X130 10G SFP+ LC LR Transceiver
JD094B
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
JD095C
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
JD096C
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
JD097C
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JG081C
HPE FlexNetwork X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
JG326A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
JG327A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
JG328A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
JG329A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable
JG330A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
JG331A
HPE FlexNetwork X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable
JC784C
HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver
JG661A
HPE X140 40G QSFP+ MPO SR4 Transceiver
JG325B
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver
JG709A
HPE X140 40G QSFP+ LC BiDi 100m MM Transceiver
JL251A
HPE X2A0 40G QSFP+ to QSFP+ 7m Active Optical Cable
JL287A
HPE X2A0 40G QSFP+ to QSFP+ 10m Active Optical Cable
JL288A
HPE X2A0 40G QSFP+ to QSFP+ 20m Active Optical Cable
JL289A
HPE X140 40G QSFP+ LC LR4L 2km SM Transceiver
JL286A
HPE FlexFabric 5700 40XG 2QSFP+ Switch (JG896A)
HPE X140 40G QSFP+ LC ER4 40km SM Transceiver
JL306A
HPE A58x0AF Back (Power Side) to Front (Port Side) Airflow 300W AC Power Supply
JG900A
HPE A58x0AF Back (Power Side) to Front (Port Side) Airflow 300W DC Power Supply
JG901A
HPE 58x0AF Back (Power Side) to Front (Port Side) Airflow Fan Tray
JC682A
HPE 58x0AF Front (Port Side) to Back (Power Side) Airflow Fan Tray
JC683A
HPE FlexFabric 5700 48G 4XG 2QSFP+ Switch (JG894A)
HPE A58x0AF Back (Power Side) to Front (Port Side) Airflow 300W AC Power Supply
JG900A
HPE A58x0AF Back (Power Side) to Front (Port Side) Airflow 300W DC Power Supply
JG901A
HPE 58x0AF 650W AC Power Supply
JC680A
HPE FlexFabric Switch 650W 48V Hot Plug NEBS-compliant DC Power Supply
JH336A
HPE 58x0AF Back (Power Side) to Front (Port Side) Airflow Fan Tray
JC682A
HPE 58x0AF Front (Port Side) to Back (Power Side) Airflow Fan Tray
JC683A
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Accessories
23
HPE FlexFabric 5700 32XGT 8XG 2QSFP+ Switch (JG898A)
HPE X140 40G QSFP+ LC ER4 40km SM Transceiver
JL306A
HPE X130 10G SFP+ LC ER 40km Transceiver
JG234A
HPE 58x0AF 650W AC Power Supply
JC680A
HPE FlexFabric Switch 650W 48V Hot Plug NEBS-compliant DC Power Supply
JH336A
HPE X711 Front (Port Side) to Back (Power Side) Airflow High Volume Fan Tray
JG552A
HPE X712 Back (Power Side) to Front (Port Side) Airflow High Volume Fan Tray
JG553A
Page
QuickSpecs
HPE FlexFabric 5700 Switch Series
Summary of Changes
24
Date
Version History
Action
Description of Change
07-May-2018
Version 14
Changed
Accessories and Configuration section updated
16-Oct-2017
Version 13
Changed
Changes made on the Features and Benefits section and
Configuration
25-Sep-2017
Version 12
Changed
Configuration section updated.
06-Mar-2017
Version 11
Changed
Configuration section updated: Add existing TXVR to All
5700 Switches
01-Aug-2016
Version 10
Added
SKUs added: JL287A, JL288A, JL289A, JL290A, JL291A,
JL292A, JL250A, JL286A
Changed
Features and Benefits updated
22-Apr-2016
Version 9
Changed
SKU descriptions updated on all the document
16-Feb-2016
Version 8
Added
SKU added: JL251A
Changed
Overview and Technical Specifications updated
08-Jan-2016
Version 7
Changed
Warranty and support updated
12-Oct-2015
Version 6
Added
Added new DC power supply: JH336A
Changed
Overview, Technical Specifications and Configuration
sections updated
12-Dec-2014
Version 5
Removed
Deleted SKU JG325A
26-Nov-2014
Version 4
Changed
Minor Changes made on the Configuration section
Removed
SKU JD093B removed from Accessories
11-Sep-2014
Version 3
Changed
Updated Technical Specifications and Accessories
Added Software-defined networking
22-Aug-2014
Version 2
Changed
Fixed error on Overview Section
18-Aug-2014
Version 1
Created
Document creation
Sign up for updates
© Copyright 2018 Hewlett Packard Enterprise Development LP. The information contained herein is
subject to change without notice. The only warranties for Hewlett Packard Enterprise products and
services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise
shall not be liable for technical or editorial errors or omissions contained herein.
To learn more, visit: http://www.hpe.com/networking
c04347352 - 14998 - Worldwide - V14 - 7-May-2018
Page
Loading...