Hp ProLiant Storage Server 1U rail installation instructions

HP ProLiant Storage Server 1U rail

installation instructions

companies as reflected by an associated footnote. The information in this document is subject to change without notice. www.hp.com

About this document

This document provides procedures for installing a 1U-size storage server into a rack using the rails provided. HP assumes that you are qualified in servicing computer equipment, and trained in recognizing hazards in products with hazardous energy levels.

Kit contents

1 Slide rail assembly 2 Bezel 3 Bezel brackets and screws

cl_011

Warnings and cautions

Important Safety Information

Læs dokumentet Vigtige sikkerhedsoplysninger på dokumentations-cd'en, før produktet installeres.

Prima dell'installazione, leggere sul CD le Informazioni importanti sulla sicurezza.

WARNING! Before you begin, make sure that the rack is

sufficiently stable. If provided, lower the rack leveler feet and make sure any required stabilizers are installed. If provided, extend the rack anti-tip device. Failure to extend the anti-tip device could result in personal injury or damage if the rack tips over.

CAUTION: Make sure that the rack and all equipment mounted

in the rack have a reliable ground connection. Verify that the total current of the rack components does not exceed the current rating of the power distribution unit or outlet receptacles.

Rack planning procedures

The rack resource kit ships with all HP branded or Compaq branded 9000, 10000, and H9 series racks. For more information on the content of each resource, see the rack resource kit documentation.

If you intend to deploy and configure multiple servers in a single rack, refer to the white paper on high-density deployment at the following HP web site:

www.hp.com/products/servers/platforms

Les "Viktig sikkerhetsinformasjon" på dokumentasjons-CDen før du installerer dette produktet.

Tärkeisiin turvatietoihin" Documentation CD -levyllä ennen tuotteen asentamista.

Läs dokumentet Viktig säkerhetsinformation på dokumentations-cd:n innan du installerar denna produkt.

*5697-5590*

Slide rail installation

NOTE: Depending on the rail kit provided, your rackmount rail

assemblies may vary slightly from those in the following illustrations.

1. Install the two slide rails to the sides of the rack.

NOTE: Two different types of rail kit designs are shown in the

illustration below, but both install similarly. The two rail assemblies packed in a kit are identical, but depending on the which side of the rack they are installed, each are rotated so the sliding portions of the rails are towards the center of the rack.

a. Adjust the side rail assemblies to the approximate rack depth. b. At one side of the rack, align the rail holes with the holes in the

rack and secure with the provided mounting hardware.

2. Locate the inner slide rails:

• If the rail assembly you mounted in the rack comes as one unit, remove the inner slide rails from the outer slide rails. To do so, extend the inner slide rails from the front of the rack until they lock in place. Then, press the inner rail release latch, as shown, and pull the inner slide rails straight out.

10685A

• If the inner slide rails in your kit are separate from the rail assemblies installed in the racks, remove them from the kit box and proceed to the next step.

520 1b

IMPORTANT: HP recommends leaving the rail mounting screws

loose until the server is completely installed. This eases installation by preventing binding of the server in the rack.

c. Align holes at the other end of the rack with the rail assembly

and secure with mounting hardware.

d. Install the other side rail assembly on the other side of the rack

as described in the previous steps.

Server preparation

1. Attach the two bezel brackets to the server using the supplied

bracket screws, as shown 1. Do not overtighten.

2. Attach an inner slide rail (locking latches facing out) to each side of

the server by placing the rail over the server standoffs and sliding the rail toward the rear of the server.

3. Insert the slide rail screws through the inner slide rails as shown 2,

and then tighten.

4. Attach the bezel 3 to the bezel brackets, and then lock the bezel to

the server (if desired).

5202

+ 1 hidden pages