Page 1
HP 3500-24G-PoE yl Switch HP 3500-48G-PoE yl Switch
Models
HP 3500-48G-PoE+ yl Switch
J9311A
HP 3500-24G-PoE+ yl Switch
J9310A
HP 3500-48G-PoE yl Switch
J8693A
HP 3500-24G-PoE yl Switch
J8692A
HP 3500-48-PoE Switch
J9473A
HP 3500-24-PoE Switch
J9471A
HP 3500-48 Switch
J9472A
HP 3500-24 Switch
J9470A
Key features
Advanced access layer and small distribution
Enterprise-class performance and security
Intelligent edge feature set with L2 to L4 support
Scalable 10/100/1000 PoE+ and 10/100 PoE
Unified core-to-edge HP ProVision software
Product overview
The HP 3500 Switch Series consists of advanced intelligent-edge switches, available in 24-port and 48-port fixed-port models. The
foundation for these switches is a purpose-built, programmable HP ProVision ASIC that allows the most demanding networking
features, such as quality of service (QoS) and security, to be implemented in a scalable yet granular fashion. With a variety of Gigabit
Ethernet and 10/100 interfaces; integrated PoE+, PoE, and non-PoE options; and versatile 10GbE connectivity (CX4, X2, and SFP+) on
Gigabit Ethernet switches, the 3500 Switch Series offers excellent investment protection, flexibility, and scalability, as well as ease of
deployment, operation, and maintenance.
Features and Benefits
Software-defined networking
NEW
OpenFlow
supports OpenFlow 1.0 and 1.3 specifications to enable SDN by allowing separation of the data (packet forwarding) and control
(routing decision) paths
Quality of Service (QoS)
Advanced classifier-based QoS
classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority
level and rate limit to selected traffic on a per-port or per-VLAN basis
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 1
Page 2
Layer 4 prioritization
enables prioritization based on TCP/UDP port numbers
Traffic prioritization
allows real-time traffic classification into eight priority levels mapped to eight queues
Bandwidth shaping
Port-based rate limiting
provides per-port ingress-/egress-enforced increased bandwidth
Classifier-based rate limiting
uses an access control list (ACL) to enforce increased bandwidth for ingress traffic on each port
Reduced bandwidth
provides per-port, per-queue egress-based reduced bandwidth
Class of Service (CoS)
sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number, source
port, and DiffServ
Management
Remote intelligent mirroring
mirrors selected ingress/egress traffic based on ACL, port, MAC address, or VLAN to a local or remote HP 8200 zl, 6600, 6200 yl,
5400 zl, or 3500 Switch anywhere on the network
RMON, XRMON, and sFlow v5
provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network
management applications
Uni-Directional Link Detection (UDLD)
monitors a cable between two switches and shuts down the ports on both ends if the cable is broken, turning the bidirectional
link into a unidirectional one; this prevents network problems such as loops
Management simplicity
common software features and CLI implementation across all ProVision-based switches (including the zl and yl switches)
Command authorization
leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login; an audit trail documents
activity
Friendly port names
allow assignment of descriptive names to ports
Dual flash images
provide independent primary and secondary operating system files for backup while upgrading
Multiple configuration files
stores easily to the flash image
Comware CLI
Comware-compatible CLI
bridges the experience of HP Comware CLI users who are using the HP ProVision software CLI
Display and fundamental Comware CLI commands
are embedded in the switch CLI as native commands; display output is formatted as on Comware-based switches, and
fundamental commands provide a Comware-familiar initial switch setup
Configuration Comware CLI commands
when Comware commands are entered, CLI help is elicited to formulate the correct ProVision software CLI comman
Connectivity
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 2
Page 3
IEEE 802.3af Power over Ethernet (PoE)
provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such as IP phones, wireless access points, and
security cameras
IEEE 802.3at Power over Ethernet Plus (PoE+)
provides up to 30 W per port to IEEE 802.3 for devices that use PoE/PoE+, such as video IP phones, IEEE 802.11n wireless access
points, and advanced pan/zoom/tilt security cameras
Prestandard PoE support
detects and provides power to prestandard PoE devices; see list of supported devices in the product FAQs at
www.hp.com/networking
Jumbo frames
on Gigabit Ethernet and 10-Gigabit Ethernet ports, jumbo frames allow high-performance remote backup and disaster-recovery
services
Auto-MDIX
provides automatic adjustments for straight-through or crossover cables on all 10/100 and 10/100/1000 ports
IPv6
IPv6 host
enables switches to be managed in an IPv6 network
Dual stack (IPv4 and IPv6)
transitions from IPv4 to IPv6, supporting connectivity for both protocols
MLD snooping
forwards IPv6 multicast traffic to the appropriate interface
IPv6 ACL/QoS
supports ACL and QoS for IPv6 network traffic
IPv6 routing
supports static and OSPFv3 routing protocols
6in4 tunneling
supports encapsulation of IPv6 traffic in IPv4 packets
Performance
High-speed/capacity architecture
up to 153.6 Gbps crossbar switching fabric provides intra- and inter-module switching with up to 111.5 million pps throughput
on the purpose-built ProVision ASICs
Selectable queue configurations
allows for increased performance by selecting the number of queues and associated memory buffering that best meet the
requirements of the network applications
Resiliency and high availability
NEW Virtual Router Redundancy Protocol (requires Premium License)
allows groups of two routers to dynamically back each other up to create highly available routed environments
IEEE 802.1s multiple Spanning Tree Protocols
provides high link availability in multiple VLAN environments by allowing multiple spanning trees; encompasses IEEE 802.1D
Spanning Tree Protocol and IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.3ad Link Aggregation Control Protocol (LACP) and HP port trunking
support up to 144 trunks, each with up to eight links (ports) per trunk
Distributed trunking
enables loop-free and redundant network topology without using Spanning Tree Protocol; allows a server or switch to connect
to two switches using one logical trunk for redundancy and load sharing
Uplink Failure Detection
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 3
Page 4
provides active-standby network path redundancy for servers that are configured for active-standby NIC teaming
NEW SmartLink
provides easy-to-configure link redundancy of active and standby link
Layer 2 switching
IEEE 802.1ad Q-in-Q (requires Premium License)
increases the scalability of an Ethernet network by providing a hierarchical structure; connects multiple LANs on a high-speed
campus or metro network
HP switch meshing
dynamically load balances across multiple active redundant links to increase available aggregate bandwidth
VLAN support and tagging
supports the IEEE 802.1Q standard and 2,048 VLANs simultaneously
IEEE 802.1v protocol VLANs
isolate select non-IPv4 protocols automatically into their own VLANs
GARP VLAN Registration Protocol
allows automatic learning and dynamic assignment of VLANs
Rapid Per-VLAN Spanning Tree (RPVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage; is compatible with PVST+
Layer 3 services
User Datagram Protocol (UDP) helper function
allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and prevents
server spoofing for UDP services such as DHCP
Loopback interface address
defines an address in Routing Information Protocol (RIP) and Open Standard Path First (OSPF), improving diagnostic capability
Route maps
provide more control during route redistribution; allow filtering and altering of route metrics
Layer 3 routing
Static IP routing
provides manually configured routing for both IPv4 and IPv6 networks
Routing Information Protocol (RIP)
provides RIPv1 and RIPv2 routing
OSPF (requires Premium License)
provides OSPFv2 for IPv4 routing and OSPFv3 for IPv6 routing
Border Gateway Routing Protocol (requires Premium License)
provides IPv4 Border Gateway Routing Protocol that is scalable, robust, and flexible
Security
Access control lists
(ACLs)
provide filtering based on the IP field, source/destination IP address/subnet, and source/destination TCP/UDP port number on a
per-VLAN or per-port basis
Multiple user authentication methods
IEEE 802.1X users per port
provides authentication of multiple IEEE 802.1X users per port
Web-based authentication
authenticates from Web browser for clients that do not support IEEE 802.1X supplicant
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 4
Page 5
MAC-based authentication
client is authenticated with the RADIUS server based on client's MAC authentication
Concurrent IEEE 802.1X, Web, and MAC authentication schemes per port
switch port accepts up to 32 sessions of IEEE 802.1X, Web, and MAC authentications
Virus throttling
detects traffic patterns typical of worm-type viruses and either throttles or entirely prevents the virus from spreading across the
routed VLANs or bridged interfaces without requiring external appliances
DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
Secure management access
delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or SNMPv3
USB Secure Autorun (requires HP PCM+)
deploys, diagnoses, and updates a switch using a USB flash drive; works with a secure credential to prevent tampering
Switch CPU protection
provides automatic protection against malicious network traffic trying to shut down the switch
ICMP throttling
defeats ICMP denial-of-service attacks by enabling any switch port to automatically throttle ICMP traffic
Identity-driven ACL
enables implementation of a highly granular and flexible access security policy and VLAN assignment specific to each
authenticated network user
STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks
Dynamic IP lockdown
works with DHCP protection to block traffic from unauthorized hosts, preventing IP source address spoofing
Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
STP Root Guard
protects the root bridge from malicious attacks or configuration mistakes
Detection of malicious attacks
monitors 10 types of network traffic and sends a warning when an anomaly that potentially can be caused by malicious attacks
is detected
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
MAC address lockout
prevents particular configured MAC addresses from connecting to the network
Source-port filtering
allows only specified ports to communicate with each other
RADIUS/TACACS+
eases switch management security administration by using a password authentication server
Secure Shell
encrypts all transmitted data for secure remote CLI access over IP networks
Secure Sockets Layer (SSL)
encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch
Secure FTP
allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch
configuration file
Management Interface Wizard
helps secure management interfaces such as SNMP, telnet, SSH, SSL, Web, and USB at the desired level
Switch management logon security
helps secure switch CLI logon by optionally requiring either RADIUS or TACACS+ authentication
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 5
Page 6
Security banner
displays a customized security policy when users log in to the switch
Convergence
IP multicast routing (requires Premium License)
includes PIM Sparse and Dense modes to route IP multicast traffic
IP multicast snooping (data-driven IGMP)
prevents flooding of IP multicast traf
LLDP-MED (Media Endpoint Discovery)
defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure
network devices such as IP phones
PoE allocations
support multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user specified) to allocate PoE power for more efficient
energy savings
Auto VLAN configuration for voice
RADIUS VLAN
uses a standard RADIUS attribute and LLDP-MED to automatically configure a VLAN for IP phones
CDPv2
uses CDPv2 to configure legacy IP phones
NEW Local MAC Authentication
assigns attributes such as VLAN and QoS using locally configured profile that can be a list of MAC prefixes
Warranty and support
Lifetime Warranty 2.0
advance hardware replacement for as long as you own the product with next-business-day delivery (available in most countries)†
Electronic and telephone support (for Lifetime Warranty 2.0)
limited 24x7 telephone support is available from HP for the first 3 years; limited electronic and business hours telephone
support is available from HP for the entire warranty period; to reach our support centers, refer to
www.hp.com/networking/contact-support
; for details on the duration of support provided with your product purchase, refer
to
www.hp.com/networking/warrantysummary
Software releases
to find software for your product, refer to
www.hp.com/networking/support
; for details on the software
releases available with your product purchase, refer to
www.hp.com/networking/warrantysummary
†HP warranty includes repair or replacement of hardware for as long as you own the product, with next business day advance
replacement (available in most countries). The disk drive included with HP AllianceOne Advanced Services and Services zl Modules, HP
Threat Management Services zl Module, HP AllianceOne Extended zl Module with Riverbed Steelhead, HP MSM765zl Mobility Controller
and HP Survivable Branch Communication zl Module powered by Microsoft Lync has a five-year hardware warranty. For details, refer to
the Software license and hardware warranty statements at:
www.hp.com/networking/warranty
.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 6
Page 7
Build To Order:
BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.
HP 3500-24 Switch
J9470A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J9470A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9470A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-24-PoE Switch
J9471A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J9471A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9471A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-24G-PoE Yl Switch
J8692A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J8692A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J8692A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-24G-PoE+ yl Switch
J9310A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 7
Page 8
PDU Cable NA/MEX/TW/JP
J9310A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9310A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48 Switch
J9472A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J9472A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9472A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48-PoE Switch
J9473A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J9473A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9473A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48G-PoE yl Switch
J8693A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J8693A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J8693A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48G-PoE+ yl Switch
J9311A
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 8
Page 9
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J9311A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9311A#B2C
C15 PDU Jumper Cord (ROW)
Configuration Rules:
Note 1
The following Transceivers install into this Switch:
HP X111 100M SFP LC FX Transceiver
J9054C
HP X112 100M SFP LC BX-D Transceiver
J9099B
HP X112 100M SFP LC BX-U Transceiver
J9100B
HP X121 1G SFP LC LH Transceiver
J4860C
HP X121 1G SFP LC LX Transceiver
J4859C
HP X121 1G SFP LC SX Transceiver
J4858C
HP X122 1G SFP LC BX-D Transceiver
J9142B
HP X122 1G SFP LC BX-U Transceiver
J9143B
Note 2
Localization required on orders without #B2B or #B2C options.
Remarks:
Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C
ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level
CTO)
Factory Racked Models
HP 3500-48G-PoE+ yl Switch
J9311A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J9311A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9311A#B2C
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 9
Page 10
C15 PDU Jumper Cord (ROW)
HP 3500-24G-PoE+ yl Switch
J9310A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J9310A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9310A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48G-PoE yl Switch
J8693A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J8693A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J8693A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-24G-PoE Yl Switch
J8692A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J8692A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J8692A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48-PoE Switch
J9473A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 10
Page 11
PDU Cable NA/MEX/TW/JP
J9473A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9473A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-24-PoE Switch
J9471A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J9471A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9471A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48 Switch
J9472A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J9472A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9472A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-24 Switch
J9470A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP
J9470A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
J9470A#B2C
C15 PDU Jumper Cord (ROW)
Configuration Rules
Note 1
The following Transceivers install into this Module (Max=4):
HP X111 100M SFP LC FX Transceiver
J9054C
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 11
Page 12
HP X112 100M SFP LC BX-D Transceiver
J9099B
HP X112 100M SFP LC BX-U Transceiver
J9100B
HP X121 1G SFP LC LH Transceiver
J4860C
HP X121 1G SFP LC LX Transceiver
J4859C
HP X121 1G SFP LC SX Transceiver
J4858C
HP X122 1G SFP LC BX-D Transceiver
J9142B
HP X122 1G SFP LC BX-U Transceiver
J9143B
Note 2
If this switch is factory installed in HP Universal Racks, Then the J9583A or J9583A#0D1 is required.
EMEA then J9583A is required.
APD, Japan and China then J9583A#0D1 is required.
CLIC Only - Allow the J9583AZ in all regions.
Enter the following menu selections as integrated to the CTO Model X server above if order is factory built.
Modules
J9311A, J9310A, J8693A and J8692A only - System (std 0 // max=1) User Selection (min 0 / max=1) per
Chassis
HP 10 GbE 2-port X2 / 2-port CX4 yl Module
J8694A
min=0 \ max=2 X2 Transceivers
See Configuration Note:1
HP 10GbE 2-port SFP+/2-port CX4 yl Mod
J9312A
min=0 \ max=2 SFP+ Transceivers
See Configuration Note:2
Configuration Rules:
Note 1
The following Transceivers install into this Module:
HP X131 10G X2 SC SR Transceiver
J8436A
HP X131 10G X2 SC LR Transceiver
J8437A
HP X131 10G X2 SC ER Transceiver
J8438A
HP X131 10G X2 SC LRM Transceiver
J9144A
Note 2
The following Transceivers install into this Module:
HP X132 10G SFP+ LC ER Transceiver
J9153A
HP X132 10G SFP+ LC LR Transceiver
J9151A
HP X132 10G SFP+ LC LRM Transceiver
J9152A
HP X132 10G SFP+ LC SR Transceiver
J9150A
HP X242 SFP+ SFP+ 1m Direct Attach Cable
J9281B
HP X242 SFP+ SFP+ 3m Direct Attach Cable
J9283B
HP X242 SFP+ SFP+ 7m Direct Attach Cable
J9285B
HP X244 XFP SFP+ 1m Direct Attach Cable
J9300A
HP X244 XFP SFP+ 3m Direct Attach Cable
J9301A
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 12
Page 13
HP X244 XFP SFP+ 5m Direct Attach Cable
J9302A
HP X242 SFP+ 10m DAC Cable
J9286B
HP X242 SFP+ 15m DAC Cable
J9287B
Transceivers
SFP Transceivers
HP X111 100M SFP LC FX Transceiver
J9054C
HP X112 100M SFP LC BX-D Transceiver
J9099B
HP X112 100M SFP LC BX-U Transceiver
J9100B
HP X121 1G SFP LC LH Transceiver
J4860C
HP X121 1G SFP LC LX Transceiver
J4859C
HP X121 1G SFP LC SX Transceiver
J4858C
HP X122 1G SFP LC BX-D Transceiver
J9142B
HP X122 1G SFP LC BX-U Transceiver
J9143B
SFP+ Transceivers
HP X132 10G SFP+ LC ER Transceiver
J9153A
HP X132 10G SFP+ LC LR Transceiver
J9151A
HP X132 10G SFP+ LC LRM Transceiver
J9152A
HP X132 10G SFP+ LC SR Transceiver
J9150A
HP X242 10G SFP+ SFP+ 1m DAC Cable
J9281B
HP X242 10G SFP+ SFP+ 3m DAC Cable
J9283B
HP X242 10G SFP+ SFP+ 7m DAC Cable
J9285B
HP X244 10G XFP SFP+ 1m DAC Cable
J9300A
HP X244 10G XFP SFP+ 3m DAC Cable
J9301A
HP X244 10G XFP SFP+ 5m DAC Cable
J9302A
HP X242 10G SFP+ 10m DAC Cable
J9286B
HP X242 10G SFP+ 15m DAC Cable
J9287B
X2 Transceivers
HP X131 10G X2 SC ER Transceiver
J8438A
HP X131 10G X2 SC LR Transceiver
J8437A
HP X131 10G X2 SC LRM Transceiver
J9144A
HP X131 10G X2 SC SR Transceiver
J8436A
Cables
Multi-Mode Cables
HP .5m Multi-mode OM3 LC/LC FC Cable
AJ833A
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 13
Page 14
HP 1m Multi-mode OM3 LC/LC FC Cable
AJ834A
HP 2 m Multimode OM3 LC/LC FC Cable
AJ835A
HP 5 m Multimode OM3 LC/LC FC Cable
AJ836A
HP 15 m Multimode OM3 LC/LC FC Cable
AJ837A
HP 30 m Multimode OM3 LC/LC FC Cable
AJ838A
HP 50 m Multimode OM3 LC/LC FC Cable
AJ839A
HP Premier Flex LC/LC OM4 2f 1m Cbl
QK732A
HP Premier Flex LC/LC OM4 2f 2m Cbl
QK733A
HP Premier Flex LC/LC OM4 2f 5m Cbl
QK734A
HP Premier Flex LC/LC OM4 2f 15m Cbl
QK735A
HP Premier Flex LC/LC OM4 2f 30m Cbl
QK736A
HP Premier Flex LC/LC OM4 2f 50m Cbl
QK737A
Switch Enclosure Options
Rack Mount kits
HP X410 1U Univ 4-post Rack Mnt Kit
J9583A
See Configuration Note:1,
2
Rack Shelf
AB469A
See Configuration Note:3
Configuration Rules:
Note 1
Default with switch.
Note 2
If the J9583A is ordered in EMEA fire the following UNBUILDABLE error:
"The J9583A cannot be ordered with option integrated to the Rack in the EMEA region. The Rack Mount kit
must be ordered as BTO using supplier 8OCZ."
Note 3
This has existing rules that say 1 per 20 if 1U and 1 per 10 if its 3U or more. This rule is fine for ProCurve.
NOTE:
Both parts above are required to ship the 62xx Series Switches installed in a rack. Exceptions- The
Shelf Kit (AB469A) may be removed if the Switch is supported underneath by a full depth Server of 3U height
or greater mounted on fixed rails
Software
HP 3500 yl Premium License
J8993A
External Power supplies
HP 620 Redundant/External Power Supply
J8696A
Height = 1U
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 14
Page 15
HP 630 Red and/or External Power Supply
J9443A
Height = 1U
See Configuration Note:1
Configuration Rules:
Note 1
See HPN Rack Menu for integration details.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 15
Page 16
HP 3500-48G-PoE+ yl
Switch
(J9311A)
I/O ports and slots
1 open module slot
44 autosensing 10/100/1000 ports; Media Type: Auto-MDIX; Duplex: 10BASE-
T/100BASE-TX: half or full; 1000BASE-T: full only (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T)
1 RJ-45 serial console port
4 dual-personality ports; each port can be used as either an RJ-45
10/100/1000 port (IEEE 802.3 Type 10BASE-T; IEEE 802.3u Type 100BASETX; IEEE 802.3ab 1000BASE-T Gigabit Ethernet) with PoE or an open
mini-GBIC slot (for use with mini-GBIC transceivers)
Supports a maximum of 4 10GbE ports, with optional module
Physical characteristics
Dimensions
17.44(w) x 16.93(d) x 1.73(h) in (44.3 x 43.0 x 4.4
cm) (1U height)
Weight
15.54 lb (7.05 kg)
Memory and processor
10G module
ARM9 @ 200 MHz; packet buffer size: 36 Mb QDR
SDRAM
Management Module
Stackable memory and processor: Freescale
PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB
compact flash, 256 MB DDR SDRAM
Mounting and enclosure
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); horizontal surface mounting only
Performance
1000 Mb Latency
< 3.4 µs (FIFO 64-byte packets)
10 Gbps Latency
< 2.1 µs (FIFO 64-byte packets)
Throughput
up to 111.5 million pps
Routing/Switching
capacity
149.8 Gb/s
Switch fabric speed
153.6 Gb/s
Routing table size
10000 entries (IPv4)
MAC address table size
64000 entries
Environment
Operating temperature
32°F to 131°F (0°C to 55°C); 32°F to 104°F (40°C)
when used with any SFP+ 10-GbE
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 95% @ 149°F (65°C), noncondensing
Altitude
up to 15,000 ft (4.6 km)
Acoustic
Power: 58.0 dB, Pressure: 42.0 dB ISO 7779, ISO
9296
Electrical characteristics
Frequency
50/60 Hz
Description
The switch automatically adjusts to any voltage
between 100-127 and 200-240 V with either 50 or
60 Hz.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 16
Page 17
Maximum heat
dissipation
1144 BTU/hr (1206.9 kJ/hr)
AC voltage
100-127/200-240 VAC
Current
7.3/3.3 A
Idle power
132 W
Maximum power rating
638 W
PoE power
398 W
Safety
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal
line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reduction, 0.5 period; 30%
reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM (included); command-line interface; Web browser;
configuration menu; out-of-band management (serial RS-232C)
Notes
J8177B Gigabit 1000BASE-T mini-GBIC is not supported on the 3500 series
switches.
Supported 1G SFP transceivers are revision "B" or later (product number ends
with the letter "B" or later, for example, J9142B, J8177C).
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (H4496E)
3-year, 4-hour onsite, 24x7 coverage for hardware (H2893E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support
and SW updates (U6319E)
3-year, 24x7 SW phone support, software updates (UE264E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR894E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR895E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR884E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR885E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR886E)
4-year, 24x7 SW phone support, software updates (UR887E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR888E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR889E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 17
Page 18
(UR890E)
5-year, 24x7 SW phone support, software updates (UR891E)
3 Yr 6 hr Call-to-Repair Onsite (UW365E)
4 Yr 6 hr Call-to-Repair Onsite (UW366E)
5 Yr 6 hr Call-to-Repair Onsite (UW367E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR898E)
1-year, 24x7 software phone support, software updates (HR897E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
support and software updates (HR896E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS618E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS619E)
3-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS620E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS621E)
4-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS622E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS623E)
5-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS624E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS625E)
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 3500-24G-PoE+ yl
Switch
(J9310A)
I/O ports and slots
20 autosensing 10/100/1000 ports; Media Type: Auto-MDIX; Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T)
1 RJ-45 serial console port
4 dual-personality ports; each port can be used as either an RJ-45
10/100/1000 port (IEEE 802.3 Type 10BASE-T; IEEE 802.3u Type 100BASETX; IEEE 802.3ab 1000BASE-T Gigabit Ethernet) with PoE or an open
mini-GBIC slot (for use with mini-GBIC transceivers)
1 open module slot
Supports a maximum of 4 10-GbE ports
Physical characteristics
Dimensions
17.44(w) x 15.43(d) x 1.73(h) in (44.3 x 39.2 x 4.4
cm) (1U height)
Weight
13.86 lb (6.29 kg)
Memory and processor
10G module
ARM9 @ 200 MHz; packet buffer size: 36 Mb QDR
SDRAM
Management Module
Stackable memory and processor: Freescale
PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB
compact flash, 256 MB DDR SDRAM
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 18
Page 19
Mounting and enclosure
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); horizontal surface mounting only
Performance
1000 Mb Latency
< 3.4 µs (FIFO 64-byte packets)
10 Gbps Latency
< 2.1 µs (FIFO 64-byte packets)
Throughput
up to 75.7 million pps
Routing/Switching
capacity
101.8 Gb/s
Switch fabric speed
105.6 Gb/s
Routing table size
10000 entries (IPv4)
MAC address table size
64000 entries
Environment
Operating temperature
32°F to 131°F (0°C to 55°C); 32°F to 104°F (40°C)
when used with any X2 10-GbE
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 15,000 ft. (4.6 km)
Acoustic
Power: 57.0 dB, Pressure: 40.5 dB ISO 7779, ISO
9296
Electrical characteristics
Frequency
50 / 60 Hz
Description
The switch automatically adjusts to any voltage
between 100-127 and 200-240 V with either 50 or
60 Hz.
Maximum heat
dissipation
865 BTU/hr (912.9 kJ/hr)
AC voltage
100-127/200-240 VAC
Current
6.6 / 3.0 A
Idle power
94 W
Maximum power rating
616 W
PoE power
398 W
Safety
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal
line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 19
Page 20
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reduction, 0.5 period; 30%
reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM (included); command-line interface; Web browser;
configuration menu; out-of-band management (serial RS-232C)
Notes
J8177B Gigabit 1000BASE-T mini-GBIC is not supported on the 3500 series
switches.
Supported 1G SFP transceivers are revision "B" or later (product number ends
with the letter "B" or later, for example, J9142B, J8177C).
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (U2855E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U2856E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support
and SW updates (U6304E)
3-year, 24x7 SW phone support, software updates (UE262E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR889E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR890E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7
software phone support (HR891E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR868E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR869E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR870E)
4-year, 24x7 SW phone support, software updates (UR871E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR872E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR873E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR874E)
5-year, 24x7 SW phone support, software updates (UR875E)
3 Yr 6 hr Call-to-Repair Onsite (UW356E)
4 Yr 6 hr Call-to-Repair Onsite (UW357E)
5 Yr 6 hr Call-to-Repair Onsite (UW358E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR893E)
1-year, 24x7 software phone support, software updates (HR892E)
1-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS610E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS611E)
3-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS612E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS613E)
4-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS614E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 20
Page 21
Exchange (HS615E)
5-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS616E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS617E)
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 3500-48G-PoE yl
Switch
(J8693A)
I/O ports and slots
44 autosensing 10/100/1000 ports; Media Type: Auto-MDIX; Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T)
4 dual-personality ports; each port can be used as either an RJ-45
10/100/1000 port (IEEE 802.3 Type 10BASE-T; IEEE 802.3u Type 100BASETX; IEEE 802.3ab 1000BASE-T Gigabit Ethernet) with PoE or an open mini-GBIC
slot (for use with mini-GBIC transceivers)
1 open module slot
Supports a maximum of 4 10GbE ports, with optional module
Physical characteristics
Dimensions
17.44(w) x 16.93(d) x 1.73(h) in (44.3 x 43.0 x 4.4
cm) (1U height)
Weight
16.09 lb (7.3 kg)
Memory and processor
10G module
ARM9 @ 200 MHz; packet buffer size: 36 Mb QDR
SDRAM
Management Module
Stackable memory and processor: Freescale
PowerPC 8540 @ 666 MHz, 4 MB flash Mb, 128 MB
compact flash, 256 MB DDR SDRAM
Mounting and enclosure
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); horizontal surface mounting only
Performance
1000 Mb Latency
< 3.4 µs (FIFO 64-byte packets)
10 Gbps Latency
< 2.1 µs (FIFO 64-byte packets)
Throughput
up to 111.5 million pps
Routing/Switching
capacity
149.8 Gb/s
Switch fabric speed
153.6 Gb/s
Routing table size
10000 entries (IPv4)
MAC address table size
64000 entries
Environment
Operating temperature
32°F to 131°F (0°C to 55°C); 32°F to 104°F (40°C)
when used with any X2 10-GbE
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 21
Page 22
Nonoperating/Storage
relative humidity
15% to 95% @ 149°F (65°C), noncondensing
Altitude
up to 15,000 ft (4.6 km)
Acoustic
Power: 55.6 dB, Pressure: 45.3 dB ISO 7779, ISO
9296
Electrical characteristics
Achieved Miercom Certified Green Award
Frequency
50/60 Hz
Description
The switch automatically adjusts to any voltage
between 100-127 and 200-240 V with either 50 or
60 Hz.
Maximum heat
dissipation
1144 BTU/hr (1206.9 kJ/hr)
AC voltage
100-127/200-240 VAC
Current
10.0/5.0 A
Idle power
142 W
Maximum power rating
705 W
PoE power
398 W
Safety
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal
line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reduction, 0.5 period; 30%
reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM (included); command-line interface; Web browser;
configuration menu; out-of-band management (serial RS-232C)
Notes
J8177B Gigabit 1000BASE-T mini-GBIC is not supported on the 3500 series
switches.
Supported 1G SFP transceivers are revision "B" or later (product number ends
with the letter "B" or later, for example, J9142B, J8177C).
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (H4496E)
3-year, 4-hour onsite, 24x7 coverage for hardware (H2893E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support
and SW updates (U6319E)
3-year, 24x7 SW phone support, software updates (UE264E)
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 22
Page 23
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR894E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR895E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR884E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR885E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR886E)
4-year, 24x7 SW phone support, software updates (UR887E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR888E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR889E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR890E)
5-year, 24x7 SW phone support, software updates (UR891E)
3 Yr 6 hr Call-to-Repair Onsite (UW365E)
4 Yr 6 hr Call-to-Repair Onsite (UW366E)
5 Yr 6 hr Call-to-Repair Onsite (UW367E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR898E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
support and software updates (HR896E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS618E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS619E)
3-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS620E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS621E)
4-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS622E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS623E)
5-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS624E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS625E)
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 3500-24G-PoE yl
Switch
(J8692A)
I/O ports and slots
20 autosensing 10/100/1000 ports; Media Type: Auto-MDIX; Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T)
4 dual-personality ports; each port can be used as either an RJ-45
10/100/1000 port (IEEE 802.3 Type 10Base-T; IEEE 802.3u Type 100Base-TX;
IEEE 802.3ab 1000Base-T Gigabit Ethernet) with PoE or an open mini-GBIC
slot (for use with mini-GBIC transceivers)
1 open module slot
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 23
Page 24
Supports a maximum of 4 10-GbE ports, with optional module
Physical characteristics
Dimensions
17.44(w) x 15.43(d) x 1.73(h) in (44.3 x 39.2 x 4.4
cm) (1U height)
Weight
14.11 lb (6.4 kg)
Memory and processor
10G module
ARM9 @ 200 MHz; packet buffer size: 36 Mb QDR
SDRAM
Management Module
Stackable memory and processor: Freescale
PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB
compact flash, 256 MB DDR SDRAM
Mounting and enclosure
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); horizontal surface mounting only
Performance
1000 Mb Latency
< 3.4 µs (FIFO 64-byte packets)
10 Gbps Latency
< 2.1 µs (FIFO 64-byte packets)
Throughput
up to 75.7 million pps
Routing/Switching
capacity
101.8 Gb/s
Switch fabric speed
105.6 Gb/s
Routing table size
10000 entries (IPv4)
MAC address table size
64000 entries
Environment
Operating temperature
32°F to 131°F (0°C to 55°C); 32°F to 104°F (40°C)
when used with any X2 10-GbE
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 15,000 ft (4.6 km)
Acoustic
Power: 55.1 dB, Pressure: 44.8 dB ISO 7779, ISO
9296
Electrical characteristics
Frequency
50/60 Hz
Description
The switch automatically adjusts to any voltage
between 100-127 and 200-240 V with either 50 or
60 Hz.
Maximum heat
dissipation
865 BTU/hr (912.9 kJ/hr)
AC voltage
100-127/200-240 VAC
Current
10.0/5.0 A
Idle power
98 W
Maximum power rating
623 W
PoE power
398 W
Safety
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 24
Page 25
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal
line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reduction, 0.5 period; 30%
reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM (included); command-line interface; Web browser;
configuration menu; out-of-band management (serial RS-232C)
Notes
J8177B Gigabit 1000BASE-T mini-GBIC is not supported on the 3500 series
switches.
Supported 1G SFP transceivers are revision "B" or later (product number ends
with the letter "B" or later, for example, J9142B, J8177C).
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (U2855E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U2856E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support
and SW updates (U6304E)
3-year, 24x7 SW phone support, software updates (UE262E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR889E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR890E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7
software phone support (HR891E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR868E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR869E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR870E)
4-year, 24x7 SW phone support, software updates (UR871E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR872E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR873E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR874E)
5-year, 24x7 SW phone support, software updates (UR875E)
3 Yr 6 hr Call-to-Repair Onsite (UW356E)
4 Yr 6 hr Call-to-Repair Onsite (UW357E)
5 Yr 6 hr Call-to-Repair Onsite (UW358E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR893E)
1-year, 24x7 software phone support, software updates (HR892E)
1-year, 24x7 software phone support, software updates + Next Business Day
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 25
Page 26
Hardware Exchange (HS610E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS611E)
3-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS612E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS613E)
4-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS614E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS615E)
5-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS616E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS617E)
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 3500-48-PoE Switch
(J9473A)
I/O ports and slots
44 RJ-45 autosensing 10/100 ports; Media Type: Auto-MDIX; Duplex: half or
full (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX)
4 dual-personality ports; each port can be used as either an RJ-45
10/100/1000 port (IEEE 802.3 Type 10Base-T; IEEE 802.3u Type 100Base-TX;
IEEE 802.3ab 1000Base-T Gigabit Ethernet) with PoE or an open mini-GBIC
slot (for use with mini-GBIC transceivers)
1 RS-232C DB-9 console port
Physical characteristics
Dimensions
17.44(w) x 16.93(d) x 1.73(h) in (44.3 x 43.0 x 4.4
cm) (1U height)
Weight
14.99 lb (6.8 kg)
Memory and processor
Management Module
Stackable memory and processor: Freescale
PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB
compact flash, 256 MB DDR SDRAM
Mounting and enclosure
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); horizontal surface mounting only
Performance
100 Mb Latency
< 3.4 µs (FIFO 64-byte packets)
1000 Gbps Latency
< 2.9 µs (FIFO 64-byte packets)
Throughput
up to 12.5 million pps (64-byte packets)
Routing/Switching
capacity
16.8 Gb/s
Routing table size
10000 entries (IPv4)
MAC address table size
64000 entries
Environment
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 26
Page 27
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 95% @ 149°F (65°C), noncondensing
Altitude
up to 15,000 ft (4.6 km)
Acoustic
Power: 55.6 dB, Pressure: 45.3 dB ISO 7779, ISO
9296
Electrical characteristics
Frequency
50/60 Hz
Description
The switch automatically adjusts to any voltage
between 100-127 and 200-240 V with either 50 or
60 Hz.
Maximum heat
dissipation
611 BTU/hr (644.6 kJ/hr)
AC voltage
100-127/200-240 VAC
Current
7.3/3.3 A
Idle power
133.2 W
Maximum power rating
548.8 W
PoE power
398 W
Safety
EN 60950/IEC 60950; CAN/CSA 22.2 No. 60950; UL 60950; IEC 60950
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal
line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reduction, 0.5 period; 30%
reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM (included); command-line interface; Web browser;
configuration menu; out-of-band management (serial RS-232C)
Notes
J8177B Gigabit 1000BASE-T mini-GBIC is not supported on the 3500 series
switches.
Supported 1G SFP transceivers are revision "B" or later (product number ends
with the letter "B" or later, for example, J9142B, J8177C).
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (H4496E)
3-year, 4-hour onsite, 24x7 coverage for hardware (H2893E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support
and SW updates (U6319E)
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 27
Page 28
3-year, 24x7 SW phone support, software updates (UE264E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR894E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR895E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR884E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR885E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR886E)
4-year, 24x7 SW phone support, software updates (UR887E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR888E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR889E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR890E)
5-year, 24x7 SW phone support, software updates (UR891E)
3 Yr 6 hr Call-to-Repair Onsite (UW365E)
4 Yr 6 hr Call-to-Repair Onsite (UW366E)
5 Yr 6 hr Call-to-Repair Onsite (UW367E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR898E)
1-year, 24x7 software phone support, software updates (HR897E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
support and software updates (HR896E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS618E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS619E)
3-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS620E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS621E)
4-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS622E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS623E)
5-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS624E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS625E)
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 3500-24-PoE Switch
(J9471A)
I/O ports and slots
20 RJ-45 autosensing 10/100 ports; Media Type: Auto-MDIX; Duplex: half or
full (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX)
4 dual-personality ports; each port can be used as either an RJ-45
10/100/1000 port (IEEE 802.3 Type 10Base-T; IEEE 802.3u Type 100Base-TX;
IEEE 802.3ab 1000Base-T Gigabit Ethernet) or an open mini-GBIC slot
(for use with mini-GBIC transceivers)
1 RS-232C DB-9 console port
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 28
Page 29
Physical characteristics
Dimensions
17.44(w) x 15.43(d) x 1.73(h) in (44.3 x 39.2 x 4.4
cm) (1U height)
Weight
13.23 lb (6 kg)
Memory and processor
Management Module
Stackable memory and processor: Freescale
PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB
compact flash, 256 MB DDR SDRAM
Mounting and enclosure
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); horizontal surface mounting only
Performance
100 Mb Latency
< 3.4 µs (FIFO 64-byte packets)
1000 Gbps Latency
< 2.9 µs (FIFO 64-byte packets)
Throughput
up to 8.9 million pps (64-byte packets)
Routing/Switching
capacity
12 Gb/s
Routing table size
10000 entries (IPv4)
MAC address table size
64000 entries
Environment
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 15,000 ft (4.6 km)
Acoustic
Power: 55.1 dB, Pressure: 44.8 dB ISO 7779, ISO
9296
Electrical characteristics
Frequency
50/60 Hz
Description
The switch automatically adjusts to any voltage
between 100-127 and 200-240 V with either 50 or
60 Hz.
Maximum heat
dissipation
435 BTU/hr (458.92 kJ/hr)
AC voltage
100-127/200-240 VAC
Current
6.6/3.0 A
Idle power
91 W
Maximum power rating
497 W
PoE power
398 W
Safety
EN 60950/IEC 60950; CAN/CSA 22.2 No. 60950; EN 60825; UL 60950
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 29
Page 30
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal
line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reduction, 0.5 period; 30%
reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM (included); command-line interface; Web browser;
configuration menu; out-of-band management (serial RS-232C)
Notes
J8177B Gigabit 1000BASE-T mini-GBIC is not supported on the 3500 series
switches.
Supported 1G SFP transceivers are revision "B" or later (product number ends
with the letter "B" or later, for example, J9142B, J8177C).
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (U2855E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U2856E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support
and SW updates (U6304E)
3-year, 24x7 SW phone support, software updates (UE262E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR889E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR890E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7
software phone support (HR891E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR868E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR869E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR870E)
4-year, 24x7 SW phone support, software updates (UR871E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR872E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR873E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR874E)
5-year, 24x7 SW phone support, software updates (UR875E)
3 Yr 6 hr Call-to-Repair Onsite (UW356E)
4 Yr 6 hr Call-to-Repair Onsite (UW357E)
5 Yr 6 hr Call-to-Repair Onsite (UW358E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR893E)
1-year, 24x7 software phone support, software updates (HR892E)
1-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS610E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS611E)
3-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS612E)
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 30
Page 31
3-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS613E)
4-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS614E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS615E)
5-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS616E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS617E)
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 3500-48 Switch
(J9472A)
I/O ports and slots
44 RJ-45 autosensing 10/100 ports; Media Type: Auto-MDIX; Duplex: half or
full (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX)
4 dual-personality ports; each port can be used as either an RJ-45
10/100/1000 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASETX, IEEE 802.3ab 1000BASE-T Gigabit Ethernet) with PoE, or an open miniGBIC slot (for use with mini-GBIC
1 RS-232C DB-9 console port
Physical characteristics
Dimensions
17.44(w) x 16.93(d) x 1.73(h) in
(44.3 x 43.0 x 4.4 cm) (1U height)
Weight
13.45 lb (6.1 kg)
Memory and processor
Management Module
Stackable memory and processor: Freescale
PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB
compact flash, 256 MB DDR SDRAM
Mounting and enclosure
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); horizontal surface mounting only
Performance
100 Mb Latency
< 3.4 µs (FIFO 64-byte packets)
1000 Gbps Latency
< 2.9 µs (FIFO 64-byte packets)
Throughput
up to 12.5 million pps (64-byte packets)
Routing/Switching
capacity
16.8 Gb/s
Routing table size
10000 entries (IPv4)
MAC address table size
64000 entries
Environment
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 95% @ 149°F (65°C), noncondensing
Altitude
up to 15,000 ft (4.6 km)
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 31
Page 32
Acoustic
Power: 55.8 dB, Pressure: 43.5 dB ISO 7779, ISO
9296
Electrical characteristics
Frequency
50/60 Hz
Description
The switch automatically adjusts to any voltage
between 100-127 and 200-240 V with either 50 or
60 Hz.
Maximum heat
dissipation
465 BTU/hr (490.58 kJ/hr)
AC voltage
100-127/200-240 VAC
Current
1.6/0.8 A
Idle power
96 W
Maximum power rating
136.2 W
Safety
EN 60950/IEC 60950; CAN/CSA 22.2 No. 60950; UL 60950; IEC 60950
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal
line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reduction, 0.5 period; 30%
reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM (included); command-line interface; Web browser;
configuration menu; out-of-band management (serial RS-232C)
Notes
J8177B Gigabit 1000BASE-T mini-GBIC is not supported on the 3500 series
switches.
Supported 1G SFP transceivers are revision "B" or later (product number ends
with the letter "B" or later, for example, J9142B, J8177C).
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (H4496E)
3-year, 4-hour onsite, 24x7 coverage for hardware (H2893E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support
and SW updates (U6319E)
3-year, 24x7 SW phone support, software updates (UE264E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR894E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR895E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR884E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR885E)
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 32
Page 33
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR886E)
4-year, 24x7 SW phone support, software updates (UR887E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR888E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR889E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR890E)
5-year, 24x7 SW phone support, software updates (UR891E)
3 Yr 6 hr Call-to-Repair Onsite (UW365E)
4 Yr 6 hr Call-to-Repair Onsite (UW366E)
5 Yr 6 hr Call-to-Repair Onsite (UW367E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR898E)
1-year, 24x7 software phone support, software updates (HR897E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
support and software updates (HR896E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS618E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS619E)
3-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS620E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS621E)
4-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS622E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS623E)
5-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS624E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS625E)
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 3500-24 Switch
(J9470A)
I/O ports and slots
20 RJ-45 autosensing 10/100 ports; Media Type: Auto-MDIX; Duplex: half or
full (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX)
4 dual-personality ports; each port can be used as either an RJ-45
10/100/1000 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASETX, IEEE 802.3ab 1000BASE-T Gigabit Ethernet), or an open mini-GBIC slot (for
use with mini-GBIC transceivers)
1 RS-232C DB-9 console port
Physical characteristics
Dimensions
17.44(w) x 15.43(d) x 1.73(h) in
(44.3 x 39.2 x 4.4 cm) (1U height)
Weight
11.9 lb (5.4 kg)
Memory and processor
Management Module
Stackable memory and processor: Freescale
PowerPC 8540 @ 666 MHz, 4 MB flash, 128 MB
compact flash, 256 MB DDR SDRAM
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 33
Page 34
Mounting and enclosure
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); horizontal surface mounting only
Performance
100 Mb Latency
< 3.4 µs (FIFO 64-byte packets)
1000 Gbps Latency
< 2.9 µs (FIFO 64-byte packets)
Throughput
up to 8.9 million pps (64-byte packets)
Routing/Switching
capacity
12 Gb/s
Routing table size
10000 entries (IPv4)
MAC address table size
64000 entries
Environment
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 15,000 ft (4.6 km)
Acoustic
Power: 53.1 dB, Pressure: 42.6 dB ISO 7779, ISO
9296
Electrical characteristics
Frequency
50/60 Hz
Description
The switch automatically adjusts to any voltage
between 100-127 and 200-240 V with either 50 or
60 Hz.
Maximum heat
dissipation
268 BTU/hr (282.8 kJ/hr)
AC voltage
100-127/200-240 VAC
Current
1.1/0.6 A
Idle power
68.2 W
Maximum power rating
78.7 W
Safety
CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal
line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reduction, 0.5 period; 30%
reduction, 25 periods
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 34
Page 35
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM (included); command-line interface; Web browser;
configuration menu; out-of-band management (serial RS-232C)
Notes
J8177B Gigabit 1000BASE-T mini-GBIC is not supported on the 3500 series
switches.
Supported 1G SFP transceivers are revision "B" or later (product number ends
with the letter "B" or later, for example, J9142B, J8177C).
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (U2855E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U2856E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support
and SW updates (U6304E)
3-year, 24x7 SW phone support, software updates (UE262E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR889E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR890E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7
software phone support (HR891E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR868E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR869E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR870E)
4-year, 24x7 SW phone support, software updates (UR871E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR872E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR873E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR874E)
5-year, 24x7 SW phone support, software updates (UR875E)
3 Yr 6 hr Call-to-Repair Onsite (UW356E)
4 Yr 6 hr Call-to-Repair Onsite (UW357E)
5 Yr 6 hr Call-to-Repair Onsite (UW358E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR893E)
1-year, 24x7 software phone support, software updates (HR892E)
1-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS610E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS611E)
3-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS612E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS613E)
4-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS614E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS615E)
5-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS616E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS617E)
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 35
Page 36
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Standards and protocols
(applies to all products in
series)
BGP
RFC 1997 BGP Communities Attribute
RFC 2918 Route Refresh Capability
RFC 4271 A Border Gateway Protocol 4 (BGP-4)
RFC 4456 BGP Route Reflection: An Alternative to
Full Mesh Internal BGP (IBGP)
RFC 5492 Capabilities Advertisement with BGP-4
Device management
RFC 1591 DNS (client)
HTML and telnet management
General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1AX-2008 Link Aggregation
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1v VLAN classification by Protocol and
Port
IEEE 802.1w Rapid Reconfiguration of Spanning
Tree
IEEE 802.3ad Link Aggregation Control Protocol
(LACP)
IEEE 802.3af Power over Ethernet
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 868 Time Protocol
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1542 BOOTP Extensions
RFC 2030 Simple Network Time Protocol (SNTP) v4
RFC 2131 DHCP
RFC 2453 RIPv2
RFC 2548 (MS-RAS-Vendor only)
RFC 3046 DHCP Relay Agent Information Option
RFC 3576 Ext to RADIUS (CoA only)
RFC 3768 VRRP
RFC 4675 RADIUS VLAN & Priority
RFC 4213 Basic Transition Mechanisms for IPv6
Hosts and Routers
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4291 IP Version 6 Addressing Architecture
RFC 4293 MIB for IP
RFC 4294 IPv6 Node Requirements
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
RFC 5095 Deprecation of Type 0 Routing Headers
in IPv6
RFC 5340 OSPFv3 for IPv6
RFC 5453 Reserved IPv6 Interface Identifiers
RFC 5519 Multicast Group Membership Discovery
MIB (MLDv2 only)
RFC 5722 Handling of Overlapping IPv6 Fragments
MIBs
IEEE 802.1ap (MSTP and STP MIB's only)
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1724 RIPv2 MIB
RFC 1850 OSPFv2 MIB
RFC 2021 RMONv2 MIB
RFC 2096 IP Forwarding Table MIB
RFC 2613 SMON MIB
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2787 VRRP MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
RFC 2933 IGMP MIB
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2819 Four groups of RMON: 1 (statistics), 2
(history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 36
Page 37
UDLD (Uni-directional Link Detection)
IP multicast
RFC 3376 IGMPv3 (host joins only)
RFC 3973 PIM Dense Mode
RFC 4601 PIM Sparse Mode
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2375 IPv6 Multicast Address Assignments
RFC 2460 IPv6 Specification
RFC 2464 Transmission of IPv6 over Ethernet
Networks
RFC 2710 Multicast Listener Discovery (MLD) for
IPv6
RFC 2925 Definitions of Managed Objects for
Remote Ping, Traceroute, and Lookup Operations
(Ping only)
RFC 3019 MLDv1 MIB
RFC 3315 DHCPv6 (client and relay)
RFC 3484 Default Address Selection for IPv6
RFC 3587 IPv6 Global Unicast Address Format
RFC 3596 DNS Extension for IPv6
RFC 3810 MLDv2 for IPv6
RFC 4022 MIB for TCP
RFC 4087 IP Tunnel MIB
RFC 4113 MIB for UDP
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
SNMPv1/v2c/v3
XRMON
OSPF
RFC 2328 OSPFv2
RFC 3101 OSPF NSSA
RFC 5340 OSPFv3 for IPv6
QoS/CoS
RFC 2474 DiffServ Precedence, including 8
queues/port
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 2598 DiffServ Expedited Forwarding (EF)
Security
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
RFC 3579 RADIUS Support For Extensible
Authentication Protocol (EAP)
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
QuickSpecs
HP 3500 and 3500 yl Switch Series
Technical Specifications
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 37
Page 38
HP 3500 and 3500 yl Switch Series accessories
Modules
HP 10 GbE 2-port X2 / 2-port CX4 yl Module
J8694A
HP 10 GbE 2-port SFP+/2-port CX4 yl Module
J9312A
Transceivers
HP X111 100M SFP LC FX Transceiver
J9054C
HP X112 100M SFP LC BX-D Transceiver
J9099B
HP X112 100M SFP LC BX-U Transceiver
J9100B
HP X121 1G SFP LC LH Transceiver
J4860C
HP X121 1G SFP LC LX Transceiver
J4859C
HP X121 1G SFP LC SX Transceiver
J4858C
HP X122 1G SFP LC BX-D Transceiver
J9142B
HP X122 1G SFP LC BX-U Transceiver
J9143B
HP X130 CX4 Optical Media Converter
J8439A
HP X131 10G X2 CX4 Transceiver
J8440C
HP X131 10G X2 SC ER Transceiver
J8438A
HP X131 10G X2 SC LR Transceiver
J8437A
HP X131 10G X2 SC LRM Transceiver
J9144A
HP X131 10G X2 SC SR Transceiver
J8436A
HP X132 10G SFP+ LC ER Transceiver
J9153A
HP X132 10G SFP+ LC LR Transceiver
J9151A
HP X132 10G SFP+ LC LRM Transceiver
J9152A
HP X132 10G SFP+ LC SR Transceiver
J9150A
Cables
HP X242 SFP+ SFP+ 1 m Direct Attach Cable
J9281B
HP X242 SFP+ SFP+ 3 m Direct Attach Cable
J9283B
HP X242 SFP+ SFP+ 7 m Direct Attach Cable
J9285B
HP X244 XFP SFP+ 1 m Direct Attach Cable
J9300A
HP X244 XFP SFP+ 3 m Direct Attach Cable
J9301A
HP X244 XFP SFP+ 5 m Direct Attach Cable
J9302A
HP 0.5 m Multimode OM3 LC/LC Optical Cable
AJ833A
HP 1 m Multimode OM3 LC/LC Optical Cable
AJ834A
HP 2 m Multimode OM3 LC/LC Optical Cable
AJ835A
HP 5 m Multimode OM3 LC/LC Optical Cable
AJ836A
HP 15 m Multimode OM3 LC/LC Optical Cable
AJ837A
HP 30 m Multimode OM3 LC/LC Optical Cable
AJ838A
HP 50 m Multimode OM3 LC/LC Optical Cable
AJ839A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable
QK732A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable
QK733A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable
QK734A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable
QK735A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable
QK736A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable
QK737A
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessories
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 38
Page 39
HP X242 SFP+ to SFP+ 10m Direct Attach Copper Cable
J9286B
HP X242 SFP+ to SFP+ 15m Direct Attach Copper Cable
J9287B
EPS/RPS
HP 620 Redundant/External Power Supply
J8696A
HP 630 Redundant and/or External Power Supply
J9443A
Mounting Kit
HP X410 1U Universal 4-Post Rack Mounting Kit
J9583A
License
HP 3500 yl Premium License
J8993A
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessories
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 39
Page 40
NOTE:
Details are not available for all accessories. The following specifications were available at the time of publication.
HP 10GbE 2-port X2/2port CX4 yl Module
(J8694A)
Ports
2 open 10-GbE X2 transceiver slots
2 10-GbE ports (IEEE 802.3ak Type 10GBASE-CX4); Duplex: full only
Physical characteristics
Dimensions
7.76(d) x 7.52(w) x 14.29(h) in. (19.7 x 19.1 x 36.3
cm)
Weight
1.54 lb. (0.7 kg)
Environment
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95%, noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90%, noncondensing
Cabling
Maximum distance:
• CX4: 15 m using CX4 cable or 300 m using media converter with ribbon MMF
Notes
Only the two fixed CX4 ports on this module support HP ProCurve 10-GbE CX4
Media Converter (J8439A).
Operating temperature is 32°F to 104°F (0°C to 40°C) if any X2 10-GbE optic or
transceiver is inserted in any X2 slot.
One 0.5 m CX4 cable is included.
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 10GbE 2-port SFP+/2port CX4 yl Module
(J9312A)
Ports
2 SFP+ 10-GbE ports (IEEE 802.3ae Type 10GBASE-LR); Duplex: full only
2 CX4 10-GbE ports (IEEE 802.3ak Type 10GBASE-CX4); Duplex: full only
Physical characteristics
Dimensions
7.76(d) x 7.52(w) x 14.29(h) in. (19.7 x 19.1 x 36.3
cm)
Weight
1.45 lb. (0.66 kg)
Environment
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95%, noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90%, noncondensing
Cabling
Maximum distance:
• CX4: 15 m using CX4 cable or 300 m using media converter with ribbon MMF
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 40
Page 41
Notes
Only the two fixed CX4 ports on this module support HP ProCurve 10-GbE CX4
Media Converter (J8439A).
Operating temperature is 32°F to 104°F (0°C to 40°C) if any SFP+ 10-GbE optic
or transceiver is inserted in any SFP+ slot.
One 0.5 m CX4 cable is included.
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X111 100M SFP LC FX
Transceiver
(J9054C)
Ports
1 LC 100BASE-FX port (IEEE 802.3u Type 100BASE-FX); Duplex: half or full
Physical characteristics
Dimensions
2.7(d) x 0.54(w) x 0.48(h) in. (6.86 x 1.38 x 1.22
cm)
Weight
0.06 lb. (0.03 kg)
Environment
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
5% to 95%
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage
relative humidity
5% to 85%
Altitude
up to 10,000 ft. (3 km)
Cabling
Cable type:
62.5/125 ìm or 50/125 ìm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively;
Maximum distance:
• 2 km (full duplex) or 412 m (half duplex)
Notes
Transmitter wavelength: 1310nm
Power consumption is 1.1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the J9054B 100-FX SFP-LC
Transceiver" on the "ProCurve Mini-GBICs and SFPs" Manuals Web page.
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 41
Page 42
HP X112 100M SFP LC BX-D
Transceiver
(J9099B)
A small form-factor
pluggable (SFP) 100Megabit BX (bi-directional)
"downstream" transceiver
that provides 100 Mbps
full-duplex connectivity up
to 10 km on one strand of
singlemode fiber. The
J9099B connects to the
J9100B "upstream"
transceiver, or to any IEEEstandard 100BASE-BX10-U
("upstream") device.
Ports
1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-D); Duplex: full
only
Physical characteristics
Dimensions
2.7(d) x 0.55(w) x 0.48(h) in. (6.86 x 1.39 x 1.22
cm)
Weight
0.04 lb. (0.03 kg)
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Cabling
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Notes
Transmit wavelength: 1550 nm. Receive wavelength: 1310 nm.
Power consumption is 1.1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9099B connects to the J9100B "upstream" transceiver, or to any IEEEstandard 100BASE-BX10-U ("upstream") device. (A 100-BX-D transceiver can
only connect to a 100-BX-U product. You cannot connect two 100-BX-D
transceivers together.)
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X112 100M SFP LC BX-U
Transceiver
(J9100B)
A small form-factor
pluggable (SFP) 100Megabit BX (bi-directional)
"upstream" transceiver
that provides 100 Mbps
full-duplex connectivity up
to 10 km on one strand of
singlemode fiber. The
J9100B connects to the
J9099B "downstream"
transceiver, or to any IEEEstandard 100BASE-BX10-D
("downstream")
device.
Ports
1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-U); Duplex: full
only
Physical characteristics
Dimensions
2.7(d) x 0.55(w) x 0.48(h) in. (6.86 x 1.39 x 1.22
cm)
Weight
0.07 lb. (.03 kg)
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Cabling
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 42
Page 43
0.5-10,000 m (single-mode fiber)
Notes
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9100B connects to the J9099B "downstream" transceiver, or to any IEEEstandard 100BASE-BX10- D ("downstream") device. (A 100-BX-U transceiver
can only connect to a 100-BX-D product. You cannot connect two 100-BX-U
transceivers together.)
Transmit wavelength: 1310 nm. Receive wavelength: 1550 nm.
Power consumption is 1.1 watts maximum.
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X121 1G SFP LC LH
Transceiver
(J4860C)
A small form-factor
pluggable (SFP) Gigabit LH
transceiver that provides a
full-duplex Gigabit solution
up to 70 km on singlemode fiber.
Ports
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics); Duplex:
full only
Physical characteristics
Dimensions: 2.17(d) x 0.60(w) x 0.46(h) in. (5.5 x 1.53 x 1.18 cm)
Weight: 0.04 lb. (0.02 kg)
Environment
Operating temperature: -40°F to 185°F (-40°C to 85°C)
Operating relative humidity: 0% to 95% @ 77°F (25°C), noncondensing
Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
Altitude: up to 10,000 ft. (3 km)
Cabling
Cable type:
Low metal content, single-mode fiber-optic, complying with ITU-T
G.652 and ISO/IEC 793-2 Type B1;
Maximum distance:
10-70,000 m (single-mode fiber)
Notes
Power consumption is 0.8 watts typical with 1 watt maximum at 100%
utilization.
For distances less than 20 km, a 10 dB attenuator must be used.
For distances between 20 km and 40 km, a 5 dB attenuator must be used.
Attenuators can be purchased from most cable vendors.
Services
Refer to the HP website at
www.hp.com/networking/services
for details on the
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 43
Page 44
HP X121 1G SFP LC LX
Transceiver
(J4859C)
HP X121 1G SFP LC LX
Transceiver: An SFP format
gigabit transceiver with LC
connectors using LX
technology.
Ports
1 LC 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX); Duplex: full only
Physical characteristics
Dimensions: 2.24(d) x 0.54(w) x 0.486(h) in. (5.69 x 1.37 x 1.23 cm)
Weight:0.04 lb. (0.02 kg)
Environment
Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 0% to 85%, noncondensing
Nonoperating/Storage temperature: -40°F to 212°F (-40°C to 100°C)
Altitude: up to 10,000 ft. (3 km)
Cabling
Type:
Either single mode or multimode; 62.5/125 µm or 50/125 µm
(core/cladding) diameter, graded-index, low metal content, multimode
fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or
A1a, respectively; Low metal content, single-mode fiber-optic,
complying with ITU-T G.652 and ISO/IEC 793-2 Type B1;
Maximum distance:
2-550 m (multimode 62.5 µm core diameter, 500 MHz*km bandwidth)
2-550 m (multimode 50 µm core diameter, 400 MHz*km bandwidth)
2-550 m (multimode 50 µm core diameter, 500 MHz*km bandwidth)
2-10,000 m (single-mode fiber)
Notes
A mode conditioning patch cord may be needed in some multimode fiber
installations.
Wavelength: 1310nm
Power Consumption: < 500mW Typical
Services
Refer to the HP website at
www.hp.com/networking/services
for details on the
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
HP X121 1G SFP LC SX
Transceiver
(J4858C)
A small form-factor
pluggable (SFP) Gigabit SX
transceiver that provides a
full-duplex Gigabit solution
up to 550 m on multimode
fiber.
Ports
1 LC 1000BASE-SX port; Duplex: full only
Physical characteristics
Dimensions: 2.24(d) x 0.54(w) x 0.48(h) in. (5.69 x 1.37 x 1.22 cm)
Weight: 0.04 lb. (0.02 kg)
Transceiver form factor: SFP
Environment
Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 5% to 85%, noncondensing
Nonoperating/Storage temperature: -40°F to 203°F (-40°C to 85°C)
Altitude: up to 10,000 ft. (3 km)
Electrical characteristics
Power consumption typical: 0.4 W
Power consumption maximum: 0.7 W
Cabling
Type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low
metal content, multimode fiber optic, complying with ITU-T G.651 and
ISO/IEC 793-2 Type A1b or A1a, respectively;
Maximum distance:
2-220 m (62.5 µm core diameter, 160 MHz*km bandwidth
2-275 m (62.5 µm core diameter, 200 MHz*km bandwidth
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 44
Page 45
2-500 m (50 µm core diameter, 400 MHz*km bandwidth)
2-550 m (50 µm core diameter, 500 MHz*km bandwidth)
Cable length: 2-550m
Fiber type: Multi Mode
Services
Refer to the HP website at
www.hp.com/networking/services
for details on the
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
HP X122 1G SFP LC BX-D
Transceiver
(J9142B)
A small form-factor
pluggable (SFP) Gigabit-BX
(bi-directional)
"downstream" transceiver
that provides a full-duplex
Gigabit solution up to 10
km on one strand of
single-mode fiber. The
J9142B connects to the
J9143B "upstream"
transceiver, or to any IEEEstandard 1000BASE-BX10U ("upstream") device.
Ports
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex:
full only
Physical characteristics
Dimensions
2.19(d) x 0.54(w) x 0.46(h) in. (5.57 x 1.37 x 1.18
cm)
Weight
0.04 lb. (0.02 kg)
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, non-condensing
Non-operating/
Storage temperature
–40ºF to 185ºF –40ºC to 85ºC)
Cabling
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Notes
Transmit wavelength: 1490 nm. Receive wavelength: 1310 nm.
Power consumption is 1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9142B connects to the J9143B "upstream" transceiver, or to any IEEEstandard 1000BASE-BX10-U ("upstream") device. (A 1000-BX-D transceiver
can only connect to a 1000-BX-U product. You cannot connect two 1000-BX-D
transceivers together.)
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 45
Page 46
HP X122 1G SFP LC BX-U
Transceiver
(J9143B)
A small form-factor
pluggable (SFP) Gigabit-BX
(bi-directional) "upstream"
transceiver that provides a
full-duplex Gigabit solution
up to 10 km on one strand
of single-mode fiber. The
J9143B connects to the
J9142B "downstream"
transceiver, or to any IEEEstandard 1000BASE-BX10D ("downstream")
device.
Ports
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex:
full only
Physical characteristics
Dimensions
2.19(d) x 0.54(w) x 0.46(h) in. (5.57 x 1.37 x 1.18
cm)
Weight
0.04 lb. (0.02 kg)
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, non-condensing
Non-operating/
Storage temperature
–40ºF to 185ºF –40ºC to 85ºC)
Cabling
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Notes
Transmit wavelength: 1310 nm. Receive wavelength: 1490 nm.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9143B connects to the J9142B "downstream" transceiver, or to any IEEEstandard 1000BASE-BX10-D ("downstream") device. (A 1000-BX-U
transceiver can only connect to a 1000-BX-D product. You cannot connect two
1000-BX-U transceivers together.)
Power consumption is 1 watt maximum.
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X130 CX4 Optical
Media Converter
(J8439A)
An optical media converter
that connects to CX4 ports,
providing 10-Gigabit
connectivity up to 300 m
on multimode fiber.
Physical characteristics
Dimensions
2.83(d) x 0.98(w) x 0.59(h) in. (7.19 x 2.49 x 1.5
cm)
Weight
.06 lb. (0.03 kg)
Cabling
Maximum distance:
• 62.5 µm multimode cable @ 150 MHz*km = 1-50 m
• 50 µm multimode cable @ 500 MHz*km = 1-100 m
• 50 µm multimode cable @ 2000 MHz*km = 1-300 m
Notes
Duplex: full
The CX4 Media Converter connects directly to the CX4 port, and a 12-strand
multimode ribbon cable is used between CX4 Media Converters.
The 12-strand multimode ribbon cable can have either 62.5 or 50 micron core
diameters, terminated by standard Multiple Terminations Push-pull Latch
(MTP) connectors in a crossover configuration. The ribbon cables are known as
Multi-fiber Push (MPO).
Users should specify a "crossover" (often called "key up/key up")
configuration for the ribbon cable. Also, specify female-female cables to
connect to ProCurve 10-GbE CX4 Media Converters.
For a suggested vendor of MPO ribbon cables, please see the "Cabling"
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 46
Page 47
answers on the "ProCurve 10-GbE Transceivers" FAQs Web page.
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X131 10G X2 CX4
Transceiver
(J8440C)
HP X131 10G X2 CX4
Transceiver: An X2 format
10-gigabit CX4 transceiver.
Ports
1 CX4 10-GbE port (IEEE 802.3ak Type 10GBASE-CX4); Duplex: full only
Connectivity
Connector type
CX4
Physical characteristics
Dimensions
3.54(d) x 1.42(w) x 0.53(h) in. (8.99 x 3.61 x 1.35
cm)
Weight
0.18 lb. (0.08 kg)
Transceiver form factor
X2
Environment
Operating temperature
32ºF to 131ºF (0ºC to 55ºC)
Operating relative
humidity
15% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Power consumption
typical
1.0 W
Power consumption
maximum
3.3 W
Cabling
Maximum distance:
• 15m with CX4 cables
• 300m with optical media converter and multimode fiber cable
Notes
Connector: CX4; Duplex: full
Use CX4 10-GbE cable (0.5-15 m) or HP X130 CX4 Optical Media Converter
(J8439A).
For suggested vendors of CX4 cables, please see the "Cabling" answers on the
"HP 10-GbE Transceivers" FAQs Web page.
Optical Media Converter (OMC) J8439A is not supported on the C version as the
power supply for the OMC was removed in this design.
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 47
Page 48
HP X131 10G X2 SC ER
Transceiver
(J8438A)
HP X131 10G X2 SC ER
Transceiver: An X2 format
10-gigabit transceiver with
SC connectors using ER
technology.
Ports
1 SC 10-GbE port (IEEE 802.3ae Type 10GBASE-ER); Duplex: full only
Connectivity
Connector type
SC
Wavelength
1550 nm
Physical characteristics
Dimensions
3.48(d) x 1.42(w) x 0.43(h) in. (8.84 x 3.61 x 1.09
cm)
Weight
0.35 lb. (0.16 kg)
Transceiver form factor
X2
Environment
Operating temperature
32ºF to 104ºF (0ºC to 40ºC)
Operating relative
humidity
15% to 95%, noncondensing
Electrical characteristics
Power consumption
typical
3 W
Power consumption
maximum
4.5 W
Cabling
Cable type::
Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and
ISO/IEC 793-2 Type B1;
Cable length
2m to 30km (max 40km on engineered links)
Fiber type
Single Mode
Notes
Conditioning patch cord cables are not supported
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X131 10G X2 SC LR
Transceiver
(J8437A)
An X2 form-factor
transceiver that supports
the 10-Gigabit LR standard,
providing 10-Gigabit
connectivity up to 10 km
on single-mode fiber.
Ports
1 SC 10-GbE port (IEEE 802.3ae Type 10GBASE-LR); Duplex: full only
Connectivity
Connector type
SC
Wavelength
1310 nm
Physical characteristics
Dimensions
3.48(d) x 1.42(w) x 0.43(h) in. (8.84 x 3.61 x 1.09
cm)
Weight
0.35 lb. (0.16 kg)
Transceiver form factor
X2
Environment
Operating temperature
32ºF to 104ºF (0ºC to 40ºC)
Operating relative
humidity
15% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Altitude
up to 10,000 ft. (3 km)
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 48
Page 49
Electrical characteristics
Power consumption
typical
2 W
Power consumption
maximum
3 W
Cabling
Cable type::
Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and
ISO/IEC 793-2 Type B1;
Maximum distance:
10 km
Cable length
2m to 10km with 9/125 ìm single-mode cable
Fiber type
Single Mode
Notes
Conditioning patch cord cables are not supported
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X131 10G X2 SC LRM
Transceiver
(J9144A)
An X2 form-factor
transceiver that supports
the 10-Gigabit LRM
standard, providing 10Gigabit connectivity up to
220 m on legacy
multimode fiber.
Ports
1 SC 10-GbE port (IEEE 802.3aq Type 10GBASE-LRM); Duplex: full only
Physical characteristics
Dimensions
3.54(d) x 1.59(w) x 0.7(h) in. (9.0 x 4.05 x 1.78 cm)
Weight
0.35 lb. (0.16 kg)
Transceiver form factor
X2
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Power consumption
typical
3.2 W
Power consumption
maximum
4.2 W
Cabling
Cable type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively (a mode conditioning patch cord may be needed
in some multimode fiber installations);
Maximum distance:
• 0.5-220m with 62.5 µm multimode cable @ 160/500 MHz*km
• 0.5-220m with 62.5 µm multimode cable @ 200/500 MHz*km
• 0.5-100m with 50 µm multimode cable @ 400/400 MHz*km
• 0.5-220m with 50 µm multimode cable @ 500/500 MHz*km
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 49
Page 50
• 0.5-220m with 50 µm multimode cable @ 1500/500 MHz*km
Cable length
.5m to 220m
Fiber type
Multi Mode
Notes
Wavelength: 1310nm
For OM3 cable (50 ìm multimode @ 1500/500 MHz*km), a mode-conditioning
patch cord is not required. Other multimode cables may require modeconditioning patch cords to achieve the maximum distances listed above.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the J9144A 10-GbE X2-SC LRM
Optic" on the "HP 10-GbE Transceivers" Manuals Web page.
Power Consumption: 4W Max
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X131 10G X2 SC SR
Transceiver
(J8436A)
HP X131 10G X2 SC SR
Transceiver: An X2 format
10-gigabit transceiver with
SC connectors using SR
technology.
Ports
1 SC 10-GbE port (IEEE 802.3ae Type 10GBASE-SR); Duplex: full only
Connectivity
Connector type
SC
Wavelength
850 nm
Physical characteristics
Dimensions
3.48(d) x 1.42(w) x 0.43(h) in. (8.84 x 3.61 x 1.09
cm)
Weight
0.35 lb. (0.16 kg)
Transceiver form factor
X2
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Nonoperating/Storage
relative humidity
0% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Power consumption
typical
1.7 W
Power consumption
maximum
2.4 W
Cabling
Cable type::
62.5/125 µm or 50/125 µm (core/cladding) graded-index, low metal content,
multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type
A1b or A1a, respectively;
Maximum distance:
2-26m with 62.5 µm multimode cable @ 160 MHz*km
2-33m with 62.5 µm multimode cable @ 200 MHz*km
2-66m with 50 µm multimode cable @ 400 MHz*km
2-82m with 50 µm multimode cable @ 500 MHz*km
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 50
Page 51
2-300m with 50 µm multimode cable @ 2000 MHz*km
Cable length
2-300m
Fiber type
Multi Mode
Notes
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X132 10G SFP+ LC ER
Transceiver
(J9153A)
The SFP+ ER Transceiver
will transmit 10Gbps over
up to 40km using standard
OM3 fiber cable. This
product expands the HP
Networking transceiver
portfolio for connections
from 0m to 40km. Use only
genuine HP transceivers
with your HP Networking
equipment to ensure
reliability and support.
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-ER); Duplex: full only
Connectivity
Connector type
LC
Wavelength
1550 nm
Physical characteristics
Dimensions
2.22(d) x 0.55(w) x 0.47(h) in. (5.65 x 1.39 x 1.19
cm)
Weight
.04 lb., Fully loaded
Transceiver form factor
SFP+
Environment
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Power consumption
typical
1.3 W
Power consumption
maximum
1.5 W
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
40km
Fiber type
Single Mode
Notes
Check switch release notes for minimum version of software required to
support this transceiver.
Some switches have limits as to how many of this particular transceiver can
be installed. See the release notes of the switch software/firmware being
used for more details.
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 51
Page 52
HP X132 10G SFP+ LC LR
Transceiver
(J9151A)
A 10-Gigabit transceiver in
SFP+ form-factor that
supports the 10-Gigabit LR
standard, providing 10Gigabit connectivity up to
10 km on single-mode
fiber.
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-LR); Duplex: full only
Connectivity
Connector type
LC
Wavelength
1310 nm
Physical characteristics
Dimensions
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
Weight
0.04 lb. (.02 kg)
Transceiver form factor
SFP+
Environment
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Power consumption
typical
0.9 W
Power consumption
maximum
1 W
Cabling
Cable type:
Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and
ISO/IEC 793-2 Type B1;
Maximum distance:
2m-10km with 9/125 µm single-mode cable
Cable length
2m to 10km
Fiber type
Single Mode
Notes
Conditioning patch cord cables are not supported.
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 52
Page 53
HP X132 10G SFP+ LC LRM
Transceiver
(J9152A)
A 10-Gigabit transceiver in
SFP+ form-factor that
supports the 10-Gigabit
LRM standard, for 10Gigabit connectivity up to
220 m on legacy
multimode fiber.
Ports
1 LC 10-GbE port (IEEE 802.3aq Type 10Gbase-LRM); Duplex: full only
Connectivity
Connector type
LC
Wavelength
1310 nm
Physical characteristics
Dimensions
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
Weight
0.04 lb. (.02 kg)
Transceiver form factor
SFP+
Environment
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Power consumption
typical
0.7 W
Power consumption
maximum
1 W
Cabling
Cable type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively (a mode conditioning patch cord may be needed
in some multimode fiber installations);
Maximum distance:
0.5-220m with 62.5 µm multimode cable @ 160/500 MHz*km
0.5-220m with 62.5 µm multimode cable @ 200/500 MHz*km
0.5-100m with 50 µm multimode cable @ 400/400 MHz*km
0.5-220m with 50 µm multimode cable @ 500/500 MHz*km
0.5-220m with 50 µm multimode cable @ 1500/500 MHz*km
Cable length
0.5m to 220m
Fiber type
Multi Mode
Notes
For OM3 cable (50 µm multimode @ 1500/500 MHz*km), a mode-conditioning
patch cord is not required. Other multimode cables may require modeconditioning patch cords to achieve the maximum distances listed above.
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 53
Page 54
HP X132 10G SFP+ LC SR
Transceiver
(J9150A)
A 10-Gigabit transceiver in
SFP+ form-factor that
supports the 10-Gigabit SR
standard, providing 10Gigabit connectivity up to
300 m on multimode fiber.
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-SR); Duplex: full only
Connectivity
Connector type
LC
Wavelength
850 nm
Physical characteristics
Dimensions
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
Weight
0.04 lb. (0.02 kg)
Transceiver form factor
SFP+
Environment
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Power consumption
typical
0.6 W
Power consumption
maximum
0.8 W
Cabling
Cable type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively;
Maximum distance:
2-26m with 62.5 µm multimode cable @ 160 MHz*km
2-33m with 62.5 µm multimode cable @ 200 MHz*km
2-66m with 50 µm multimode cable @ 400 MHz*km
2-82m with 50 µm multimode cable @ 500 MHz*km
2-300m with 50 µm multimode cable @ 2000 MHz*km
Cable length
2-300m
Fiber type
Multi Mode
Notes
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 54
Page 55
HP X242 SFP+ SFP+ 1 m
Direct Attach Cable
(J9281B)
Connectivity
Length
3.28 ft. (1 m)
Physical characteristics
Weight
0.24 lb. (0.11 kg) the cable with an SFP+
transceiver at each end of the cable
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
14ºF to 185ºF (-10ºC to 85ºC)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Notes
0.04 watts maximum per transceiver end
Notes
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X242 SFP+ SFP+ 3 m
Direct Attach Cable
(J9283B)
Connectivity
Length
10 ft. (3 m)
Physical characteristics
Weight
.49 lb. (0.22 kg), Fully loaded the cable with an
SFP+ transceiver at each end of the cable
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
14ºF to 185ºF (-10ºC to 85ºC)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Notes
0.04 watts maximum per transceiver end
Notes
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 55
Page 56
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X242 SFP+ SFP+ 7 m
Direct Attach Cable
(J9285B)
Connectivity
Length
22.97 ft. (7 m)
Physical characteristics
Weight
1.02 lb., Fully loaded the cable with an SFP+
transceiver at each end of the cable
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
14ºF to 185ºF (-10ºC to 85ºC)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Notes
0.04 watts maximum per transceiver end
Notes
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X242 SFP+ to SFP+ 10m
Direct Attach Copper
Cable
(J9286B)
Connectivity
Length
32.82 ft. (10 m)
Physical characteristics
Dimensions
12(d) x 15(w) x 3(h) in. (30.48 x 38.1 x 7.62 cm)
Weight
0.99 lb. (0.45 kg), Fully loaded the cable with an
SFP+ transceiver at each end of the cable
Environment
Operating temperature
23°F to 185°F (-5°C to 85°C)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
14°F to 185°F (-10°C to 85°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Maximum power rating
1.2 W
Notes
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 56
Page 57
infrastructure with fully loaded PoE (if equipped),
100% traffic, all ports plugged in, and all modules
populated.
0.6 watts maximum per transceiver end
Notes
Electrical Properties:
• Cable Characteristic Impedance: 100 ohms
Physical Properties:
• Cable Diameter: 0.185"
• Minimum Cable Bend Radius: .555"
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X242 SFP+ to SFP+ 15m
Direct Attach Copper
Cable (J9287B)
Connectivity
Length
49.20 ft. (15 m)
Physical characteristics
Dimensions
12(d) x 15(w) x 3(h) in. (30.48 x 38.1 x 7.62 cm)
Weight
1.74 lb. (0.79 kg), Fully loaded the cable with an
SFP+ transceiver at each end of the cable
Environment
Operating temperature
23°F to 185°F (-5°C to 85°C)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
14°F to 185°F (-10°C to 85°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics
Maximum power rating
1.2 W
Notes
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped),
100% traffic, all ports plugged in, and all modules
populated.
0.6 watts maximum per transceiver end
Notes
Electrical Properties:
• Cable Characteristic Impedance: 100 ohms
Physical Properties:
• Cable Diameter: 0.255"
• Minimum Cable Bend Radius: 0.765"
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 57
Page 58
HP X244 XFP SFP+ 1 m
Direct Attach Cable
(J9300A)
A 1m direct attach copper
cable with an XFP
connector attached on one
end and an SFP+ connector
attached on the other end.
This cable
provides a low price
connectivity option
between switches/servers/
storage to interconnect
XFP and SFP+ form factors.
Connectivity
Length
3.28 ft. (1 m)
Physical characteristics
Weight
.27 lb. (0.12 kg), Fully loaded cable with XFP
transcevier on one end and SFP+ on the other end
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
32ºF to 158ºF (0ºC to 70ºC)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
Notes
XFP end consumes 2 watts SFP+ end consumes 0.036 watts
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X244 XFP SFP+ 3 m
Direct Attach Cable
(J9301A)
A 3m direct attach copper
cable with an XFP
connector attached on one
end and an SFP+ connector
attached on the other end.
This cable provides a low
price connectivity option
between switches/servers/
storage to interconnect
XFP and SFP+ form factors.
Connectivity
Length
9.84 ft. (3 m)
Physical characteristics
Weight
.51 lb. (0.23 kg), Fully loaded cable with XFP
transcevier on one end and SFP+ on the other end
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
32ºF to 158ºF (0ºC to 70ºC)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
Cabling
Maximum distance:
• 3m Direct Attach Cable
Notes
XFP end consumes 2 watts SFP+ end consumes 0.036 watts
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 58
Page 59
HP X244 XFP SFP+ 5 m
Direct Attach Cable
(J9302A)
A 5m direct attach copper
cable with an XFP
connector attached on one
end and an SFP+ connector
attached on the other end.
This cable provides a low
price connectivity option
between switches/servers/
storage to interconnect
XFP and SFP+ form factors.
Connectivity
Length
16.4 ft. (5 m)
Physical characteristics
Weight
.74 lb. (0.34 kg), Fully loaded cable with XFP
transcevier on one end and SFP+ on the other end
Environment
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
32ºF to 158ºF (0ºC to 70ºC)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
Notes
XFP end consumes 2 watts SFP+ end conumes 0.036 watts
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 0.5 m Multimode OM3
LC/LC Optical Cable
(AJ833A)
Cabling
Cable type
:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m
Maximum distance
:
10Gbps Transfer Rate (Ethernet): 300m
Notes
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: 600 / 600 meters @850/1300nm
for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber and designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 59
Page 60
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 1 m Multimode OM3
LC/LC Optical Cable
(AJ834A)
Cabling
Cable type
:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m
Maximum distance
:
10Gbps Transfer Rate (Ethernet): 300m
Notes
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 60
Page 61
HP 2 m Multimode OM3
LC/LC Optical Cable
(AJ835A)
Cabling
Cable type
:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance
:
10Gbps Transfer Rate (Ethernet): 300m
Notes
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 61
Page 62
HP 5 m Multimode OM3
LC/LC Optical Cable
(AJ836A)
Cabling
Cable type
:
50/125 µm core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance
:
10Gbps Transfer Rate (Ethernet): 300m
Notes
Cable Specs: This specification defines the detail requirements for a tight
buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and
Ethernet assembly with LC duplex connectors on one end and LC duplex
connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 62
Page 63
HP 15 m Multimode OM3
LC/LC Optical Cable
(AJ837A)
Cabling
Cable type
:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance
:
10Gbps Transfer Rate (Ethernet): 300m
Notes
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 63
Page 64
HP 30 m Multimode OM3
LC/LC Optical Cable
(AJ838A)
Cabling
Cable type
:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance
:
10Gbps Transfer Rate (Ethernet): 300m
Notes
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 64
Page 65
HP 50 m Multimode OM3
LC/LC Optical Cable
(AJ839A)
Cabling
Cable type
:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance
:
10Gbps Transfer Rate (Ethernet): 300m
Notes
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 65
Page 66
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
1m Cable (QK732A)
Notes
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core Diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
2m Cable (QK733A)
Notes
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 66
Page 67
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
5m Cable (QK734A)
Notes
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
15m Cable
(QK735A)
Notes
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 67
Page 68
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
30m Cable
(QK736A)
Notes
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
50m Cable
(QK737A)
Notes
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Services
Refer to the HP website at
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 620
Redundant/External
Power Supply
(J8696A)
Ports
2 redundant power supply ports
Restrictions: 195 W available per port
2 external power supply ports
Restrictions: 398 W available per port
Physical characteristics
Dimensions
15.4(d) x 17.4(w) x 1.73(h) in. (39.12 x 44.2 x 4.39
cm) (1U height)
Weight
15.2 lb. (6.89 kg)
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 68
Page 69
Mounting
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); horizontal surface mounting only
Environment
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft. (3 km)
Acoustic
LwA per ISO 7779: 54.2 dB
Electrical characteristics
Maximum heat
dissipation
400 BTU/hr (422 kJ/hr), for the actual 620 itself.
PoE-powered device heat dissipation assumed to
be outside the 620.
Voltage
100-127/200-240 VAC
Current
16/8 A
Maximum power rating
1440 W
RPS power
390 W
PoE power
796 W
RPS
12 V
PoE
-50 V
Frequency
50/60 Hz
Notes
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped),
100% traffic, all ports plugged in, and all modules
populated.
Above figures are for maximum RPS and PoE
power being supplied to two switches
simultaneously. 200 - 240 V power cords shipped
with the 620 have a wall plug rated as close to 13
A as specific country standards allow.
Safety
CSA 22.2 No. 60950; EN 60950/IEC 60950; UL 60950
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3
EFT/Burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Conducted
IEC 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 69
Page 70
Voltage dips and
interruptions
IEC 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
Unmanaged power supply; provides information via LEDs (LEDs repeated on
front and back panel) or through port interfaces of attached devices
Notes
The 620 supports the HP Switch 2900 Series (RPS) and 3500yl Series
(RPS/PoE), as well as 6200yl (RPS) switches. The HP Switch 5400zl Series is
not supported.
The 620 includes four 2 m RPS/EPS cables. These cables can be used to carry
either RPS or PoE power to the switch being powered.
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (U9270E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U9271E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR854E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR855E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR857E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR858E)
3 Yr 6 hr Call-to-Repair Onsite (UW371E)
4 Yr 6 hr Call-to-Repair Onsite (UW372E)
5 Yr 6 hr Call-to-Repair Onsite (UW373E)
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 630 Redundant and/or
External Power Supply
(J9443A)
Physical characteristics
Dimensions
15(d) x 8.5(w) x 1.73(h) in. (38.1 x 21.59 x 4.39
cm) (1U height)
Weight
7.9 lb. (3.58 kg)
Environment
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft. (3 km)
Acoustic
Power: 54.2 dB; ISO 7779, ISO 9296
Electrical characteristics
Maximum heat
dissipation
535 BTU/hr (564.42 kJ/hr), for the actual 630
power supply. PoE-powered device heat
dissipation assumed to be outside the 630 power
supply.
Voltage
100-127/200-240 VAC
Current
8/4 A
Maximum power rating
740 W
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 70
Page 71
PoE power
398 W
RPS power
185 W
PoE power
398 W
Frequency
50/60 Hz
Notes
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped),
100% traffic, all ports plugged in, and all modules
populated.
PoE Power is the power supplied by the internal
power supply, it is dependent on the type and
quantity of power supplies and may be
supplemented with the use of a External Power
Supply (EPS).
200-240 V power cords shipped with the 630
power supply have a wall plug rated as close to 13
A as specific country standards allow.
Notes
The HP 630 RPS/EPS supports the HP 2910al and 3500yl-PoE+ Switches. The
HP Switch 5400zl Series is not supported.
The 630 RPS/EPS includes two 2-m RPS/EPS cables, which can bes used to
carry either RPS or PoE+ power to the switch.
Minimum software versions required: 2910al PoE+ switches require W.14.35
or later and 3500yl-PoE+ switches require K.14.52 or later
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (U9270E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U9271E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR854E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR855E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR857E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR858E)
3 Yr 6 hr Call-to-Repair Onsite (UW371E)
4 Yr 6 hr Call-to-Repair Onsite (UW372E)
5 Yr 6 hr Call-to-Repair Onsite (UW373E)
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 71
Page 72
HP X410 1U Universal 4post Rack Mounting Kit
(J9583A)
Notes
The rack mounting kit supports the 1U, full width switches in the following
switch series and the power supply: 1810 Series, 2510 Series, 2520 Series,
2610 Series, 2810 Series, 2910 Series, 3500 Series, and the 620 Power Supply
This universal rack mounting kit is design to fit the following racks: HP 10K
10642, HP 10K 10842, Panduit CN, Panduit CS, Wrightline Vantage S2, APC
Netshelter 600mm, and APC Netshelter 800mm. It may well fit many other
brands and models too.
Services
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 3500 yl Premium
License
(J8993A)
Services
3-Year, 9x5 SW phone support, software updates (UT479E)
3-year, 24x7 SW phone support, software updates (UT480E)
4-year, 24x7 SW phone support, software updates (UT456E)
5-year, 24x7 SW phone support, software updates (UT457E)
1-year, 24x7 software phone support, software updates (HS531E)
Refer to the HP website at:
www.hp.com/networking/services
for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
To learn more, visit:
www.hp.com/networking
© Copyright 2009-2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without
notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products
and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
Microsoft is a U.S. registered trademark of Microsoft Corporation.
QuickSpecs
HP 3500 and 3500 yl Switch Series
Accessory Product Details
DA - 13282 Worldwide — Version 19 — December 9, 2013
Page 72
Loading...