HP HLMA-VH00, HLMA-VL00, HLMP-V100, HLMP-V500 Datasheet
T-13/4 (5 mm), Wide Viewing
Angle, High Intensity LED
Lamps
H
Technical Data
Features
• Outstanding LED Material
Efficiency
• Extremely Wide Horizontal
Viewing Angle
• High Light Output over a
Wide Range of Currents
• Untinted, Non-diffused Lens
• Choice of Four Colors: 644
nm Red, 590 nm Amber, 570
nm Green, and 615 nm
Orange
Outline Drawing
Description
These high intensity LED lamps
provide the user with an
extremely wide 60° (horizontal)
by 30° (vertical) oval shaped
radiation pattern. Available in TS
AlGaAs red, AlInGaP amber,
AlInGaP orange, and GaP green
colors, these untinted nondiffused T-13/4 (5 mm) LEDs are
an excellent choice for outdoor
applications requiring an
extremely wide field of vision and
high brightness.
Device Selection Guide
HLMA-VH00
HLMA-VL00
HLMP-V100
HLMP-V500
Applications
• Outdoor Message Boards
• Safety Lighting Equipment
• Changeable Message Signs
• Alternative to Incandescent
Lamps
13.97 ± 0.76
(0.550 ± 0.030)
2.54 ± 0.76
2.54 ± 0.25
(0.100 ± 0.030)
(0.100 ± 0.010)
1-56
8.71 ± 0.38
(0.343 ± 0.015)
20.32
(0.800)
2.54 ± .025
(0.100 ± 0.010)
MIN
5.59 ± 0.25
(0.220 ± 0.010)
1.02
MAX
(0.040)
NOTE 1
0.51
SQUARE
(0.020)
NOMINAL
2.54 ± 0.25
(0.100 ± 0.010)
5.08 ± 0.25
(0.200 ± 0.010)
Amber Red-Orange Red Green
λd = 590 nm λd = 615 nm λd = 644 nm λd = 570 nm
HLMA-VL00 HLMA-VH00 HLMP-V100 HLMP-V500
NOTES:
1. LEAD ORIENTATION:
DEVICE TYPE
HLMP-V100
HLMP-V500
HLMA-VL00
HLMA-VH00
2. ALL DIMENSIONS ARE IN MM (INCHES).
CENTER LEAD
COMMON ANODE
COMMON CATHODE
COMMON CATHODE
COMMON CATHODE
OUTER LEADS
CATHODE
ANODE
ANODE
ANODE
5964-9292E
Absolute Maximum Ratings at T
= 25°C
A
Parameter HLMA-VL00 HLMA-VH00 HLMP-V100 HLMP-V500 Units
DC Forward Current
Peak Forward Current
Average Input Power
Reverse Voltage (I
= 200 µA)5555V
R
[1,3]
[2,3]
[2]
60
[4,5]
60
[4,5]
60 50 mA
400 400 600 180 mA
120 120 120 110 mW
Operating Temperature Range -40 to +100 -40 to +100 -55 to +85 -20 to +100 °C
Storage Temperature Range -55 to +100 -55 to +100 -55 to +100 -55 to +100 °C
Junction Temperature 110 °C
Soldering Temperature 260° C for 5 seconds
[1.59 mm (0.06 in.) below
seating plane]
Notes:
1. Derate linearly as shown in Figure 5.
2. Any pulsed operation cannot exceed the Absolute Max Peak Forward Current or the Max Allowable Average Power as specified in
Figure 6.
3. Specified with both die powered simultaneously.
4. Drive Currents between 10 mA and 30 mA are recommended for best long term performance.
5. Operation at currents below 10 mA is not recommended, please contact your Hewlett-Packard sales representative.
Optical Characteristics at T
= 25°C
A
Luminous Color, Viewing
Intensity Peak Dominant Angle Luminous
IV (mcd) Wavelength Wavelength 2θ1/2 Efficacy
@ 40 mA
[1]
λ
(nm) λ
peak
[2]
(nm) Degrees
d
[3]
η
V
Part Number Min. Typ. Typ. Typ. Typ. (lm/w)
HLMA-VL00 212 460 592 590 60° horizontal 480
HLMA-VH00 200 460 621 615 263
30° vertical
HLMP-V100 500 1000 654 644 60° horizontal 85
30° vertical
HLMP-V500 112 270 568 570 60° horizontal 595
30° vertical
Notes:
1. The luminous intensity, IV, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern
may not be aligned with this axis.
2. The dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the color of the device.
3. 2 θ
is the off-axis angle where the luminous intensity is 1/2 the on-axis intensity.
1/2
Electrical Characteristics at T
= 25°C
A
Forward Reverse Capacitance Speed of Response
Voltage Breakdown C (pF) Thermal τs (ns)
VF (Volts) VR (Volts) VF = 0, Resistance Time Constant
@ IF = 40 mA @ I
= 200 µA f = 1 MHz Rθ
R
J-PIN
e
-t/τs
Part Number Typ. Max. Min. Typ. (°C/W) Typ.
HLMA-VL00 1.90 2.4 5 120 100 13
HLMA-VH00 1.90 2.4 5 120 100 13
HLMP-V100 1.85 2.4 5 50 115 26
HLMP-V500 2.20 3.0 5 20 100 171
1-57
Loading...