HP CQ32 Service Guide

Page 1
Compaq Presario CQ32 Notebook PC HP G32 Notebook PC
Maintenance and Service Guide
Page 2
© Copyright 2010 Hewlett-Packard Development Company, L.P.
Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
First Edition: April 2010
Document Part Number: 610542-001 Rev. A
Page 3
MSG revision history
Revision Publication date Description
A July 2010
Added HP branding and updated commodities in the following location:
Product description on page 1
Added a newly supported Rubber feet kit to spare parts listings in the following
locations:
listing on page 28, and Computer feet on page 39
Added a newly supported WLAN module to spare parts listings in the
following locations:
part number listing on page 28, and WLAN module on page 45
Added a newly supported USB board to spare parts listings in the following
locations:
listing on page 28, and USB board on page 60
Added a newly supported power connector cable to spare parts listings in the
following locations:
part number listing on page 28, and Power connector cable on page 66
Added a newly supported system board to spare parts listings in the following
locations:
listing on page 28, and System board on page 78
Added newly supported processors to spare parts listings in the following
locations:
listing on page 28, and Processor on page 83
Computer major components on page 17, Sequential part number
Computer major components on page 17, Sequential
Computer major components on page 17, Sequential part number
Computer major components on page 17, Sequential
Computer major components on page 17, Sequential part number
Computer major components on page 17, Sequential part number
iii
Page 4
iv MSG revision history
Page 5
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of Information Technology Equipment (IEC 60950).
v
Page 6
vi Safety warning notice
Page 7
Table of contents
1 Product description ........................................................................................................... 1
2 External component identification ..................................................................................... 5
Identifying hardware ................................................................................................................ 5
Top components ...................................................................................................................... 6
TouchPad ................................................................................................................. 6
Lights ....................................................................................................................... 7
Button and speakers .................................................................................................. 8
Keys ........................................................................................................................ 9
Display .................................................................................................................. 10
Front component .................................................................................................................... 11
Right-side components ............................................................................................................ 11
Left-side components ............................................................................................................... 12
Rear component ..................................................................................................................... 13
Bottom components ................................................................................................................ 13
Wireless antennas .................................................................................................................. 14
Additional hardware components ............................................................................................ 15
3 Illustrated parts catalog .................................................................................................. 16
Serial number location ............................................................................................................ 16
Computer major components ................................................................................................... 17
Display assembly components ................................................................................................. 24
Plastics Kit ............................................................................................................................. 25
Mass storage devices ............................................................................................................. 26
Miscellaneous parts ................................................................................................................ 27
Sequential part number listing .................................................................................................. 28
4 Removal and replacement procedures ............................................................................ 33
Preliminary replacement requirements ....................................................................................... 33
Tools required ......................................................................................................... 33
Service considerations ............................................................................................. 33
Plastic parts ............................................................................................. 33
Cables and connectors ............................................................................. 34
vii
Page 8
Drive handling ......................................................................................... 34
Grounding guidelines .............................................................................................. 35
Electrostatic discharge damage .................................................................. 35
Packaging and transporting guidelines ........................................ 36
Workstation guidelines .............................................................. 36
Equipment guidelines ................................................................. 37
Component replacement procedures ........................................................................................ 38
Serial number ......................................................................................................... 38
Computer feet ......................................................................................................... 39
Battery ................................................................................................................... 40
Memory module ...................................................................................................... 41
RTC battery ............................................................................................................ 44
WLAN module ........................................................................................................ 45
Hard drive ............................................................................................................. 50
Optical drive .......................................................................................................... 53
Top cover ............................................................................................................... 54
Keyboard ............................................................................................................... 58
USB board ............................................................................................................. 60
Speaker assembly ................................................................................................... 62
Bluetooth module .................................................................................................... 64
Power connector cable ............................................................................................ 66
Optical drive connector ........................................................................................... 68
Power button board ................................................................................................. 70
Display assembly .................................................................................................... 72
System board ......................................................................................................... 78
Fan/heat sink assembly ........................................................................................... 80
Processor ............................................................................................................... 83
5 Setup Utility (BIOS) ......................................................................................................... 85
Starting Setup Utility ............................................................................................................... 85
Using Setup Utility .................................................................................................................. 86
Changing the language of Setup Utility ...................................................................... 86
Navigating and selecting in Setup Utility .................................................................... 86
Displaying system information ................................................................................... 87
Restoring default settings in Setup Utility ..................................................................... 87
Exiting Setup Utility ................................................................................................. 88
Setup Utility menus ................................................................................................................. 88
Main menu ............................................................................................................. 88
Security menu ......................................................................................................... 88
System Configuration menu ...................................................................................... 89
Diagnostics menu .................................................................................................... 90
viii
Page 9
6 Specifications .................................................................................................................. 91
Computer specifications .......................................................................................................... 91
33.78-cm (13.3-in) display specifications .................................................................................. 92
Hard drive specifications ........................................................................................................ 93
DVD±RW SuperMulti DL Drive with LightScribe specifications ...................................................... 94
Blu-ray ROM with LightScribe DVD±R/RW SuperMulti DL Drive ................................................... 95
System resource specifications ................................................................................................. 96
7 Backup and recovery ...................................................................................................... 97
Creating recovery discs .......................................................................................................... 98
Backing up your information .................................................................................................... 99
Using Windows Backup and Restore ....................................................................... 100
Using system restore points ..................................................................................... 100
When to create restore points .................................................................. 100
Create a system restore point ................................................................... 100
Restore to a previous date and time .......................................................... 101
Performing a recovery .......................................................................................................... 101
Recovering from the recovery discs .......................................................................... 101
Recovering from the dedicated recovery partition (select models only) ......................... 102
8 Connector pin assignments ........................................................................................... 103
Audio-out (headphone) ......................................................................................................... 103
Audio-in (microphone) .......................................................................................................... 103
External monitor ................................................................................................................... 104
RJ-45 (network) .................................................................................................................... 105
Universal Serial Bus .............................................................................................................. 105
HDMI ................................................................................................................................. 106
9 Power cord set requirements ........................................................................................ 107
Requirements for all countries or regions ................................................................................. 107
Requirements for specific countries or regions .......................................................................... 108
10 Recycling .................................................................................................................... 109
Battery ................................................................................................................................ 109
Display ............................................................................................................................... 109
Index ............................................................................................................................... 115
ix
Page 10
x
Page 11

1 Product description

Category Description Compaq Presario
CQ32
Product Name Compaq Presario CQ32 Notebook PC
Processors Intel® Core™ i5
580M, 2.66-GHz, SC turbo, 3-MB L3 cache √√
560M, 2.66-GHz, SC turbo, 3-MB L3 cache √√
540M, 2.53-GHz, SC turbo, 3-MB L3 cache √√
520M, 2.40-GHz, SC turbo, 3-MB L3 cache √√
460M, 2.53-GHz, SC turbo, 3-MB L3 cache √√
450M 2.40-GHz, SC turbo, 3-MB L3 cache √√
430M 2.26-GHz, SC turbo, 3-MB L3 cache √√
380M, 2.53-GHz, 3-MB L3 cache √√
370M, 2.40-GHz, 3-MB L3 cache √√
350M, 2.26-GHz, 3-MB L3 cache √√
HP G32 Notebook PC
Intel Core i3
HP G32
P6200, 2.13-GHz, 3-MB L3 cache √√
P6100, 2.0-GHz, 3-MB L3 cache √√
P6000, 1.86-GHz, 3-MB L3 cache √√
Chipset
Graphics Discrete graphics
Support for BD and/or HD-DVD playback with
Intel Pentium®
Intel HM55 Express √√
ATI Mobility Radeon™ HD5470 with 1024-MB of dedicated video memory 128-MB×16 DDR3, 800-MHz)
HD Decode, and DX11 Support
√√
√√
1
Page 12
Category Description Compaq Presario
CQ32
HP G32
Panel 33.78-cm (13.3-in) HD LED BrightView (1366
× 768 HD) (5.2 mm) SVA
16:9 ultra wide aspect ratio √√
Memory
Customer-accessible and upgradable √√
Supports up to 8 GB of system memory √√
DDR3, 1066-MHz, dual-channel memory (DDR3
Supports the following configurations:
Hard drives Supports the following 9.5-mm, 6.35-cm
2 SODIMM slots √√
1333 MHz downgraded to DDR3 1066 MHz)
4 GB (2 GB×2) √√
4 GB (4 GB×1) √√
3 GB (1 GB×1 + 2 GB×1) √√
2 GB (1 GB×1) √√
2 GB (1 GB×2) √√
1 GB (1 GB×1) √√
(2.5-in) SATA hard drives
√√
√√
Optical drives Supports the following 12.7-mm (0.50-in) tray
Blu-ray ROM with LightScribe DVD±R/RW
Blu-ray ROM DVD±R/RW SuperMulti DL Drive √√
DVD±R/RW SuperMulti DL Drive with
DVD±R/RW SuperMulti DL Drive √√
Camera
Fixed (no tilt), activity LED √√
640 × 480 by 24 frames per second √√
Microphone
Noise suppression, echo cancellation √√
500 GB, 7200 & 5400 rpm √√
320 GB, 7200 & 5400 rpm √√
250 GB, 7200 rpm √√
160 GB, 7200 rpm √√
load, fixed, SATA drive:
√√
SuperMulti DL Drive
√√
LightScribe
Low cost VGA camera √√
One microphone, digital √√
2 Chapter 1 Product description
Page 13
Category Description Compaq Presario
CQ32
HP G32
Audio
Supports Microsoft Premium requirements √√
Two Altec Lansing speakers √√
Ethernet
Wireless Integrated wireless local area network
Intel Centrino Wireless-N 1000 b/g/n with 2
Atheros 54g wireless 802.11 b/g/n with 2
Broadcom 802.11b/g/n with 2 antennas √√
Broadcom 802.11b/g/n 1x1 WiFi + 2070
Realtek 802.11b/g/n with 2 antennas √√
Realtek 802.11b/g/n 1x1 + Bluetooth with 2
HD audio √√
Integrated 10/100 network interface card (NIC) √√
√√
(WLAN) options by way of wireless module:
√√
antennas
√√
antennas
√√
Bluetooth combo half-minicard module with 2 antennas
√√
antennas
External media card
Supports mini versions of SD, MMC, and MS
Ports
Disabled when connected to devices through
Hot plug/unplug and auto detect for wide-
HDMI v1.3 supporting up to 1080p, 1920 x
USB 2.0 (3) √√
RJ-45 √√
Audio-in (microphone) √√
Audio-out (headphone) √√
Smart-pin AC adapter plug √√
Keyboard/pointing devices
5-in-1 Digital Media Slot; supports SD, MMC, MS, Mspro, xD
Duo with adapter (adapter not included)
VGA (Dsub 15-pin) supporting 1600 x 1200 resolution at 75 Hz
expansion port 3
aspect or standard-aspect video
1200 @ 60 Hz DVI mode
33.78-cm (13.3-inch) black textured pocket keyboard
√√
√√
√√
√√
√√
√√
√√
TouchPad supports two-way scroll with legend √√
3
Page 14
Category Description Compaq Presario
CQ32
Taps enabled by default √√
HP G32
Power requirements
6-cell (47-Wh) 2.2-Ah Li-ion battery √√
1 meter power cord √√
65-W AC adapter with Smart-Pin DC connector √√
90-W AC adapter with Smart-Pin DC connector √√
Security
Operating system Preinstalled:
Windows 7 Home Basic (32 bit) √√
FreeDOS √√
Serviceability End-user replaceable parts:
AC adapter √√
Battery (system) √√
Hard drive √√
Memory module √√
Optical drive √√
6-cell (55-Wh) 2.55-Ah Li-ion battery √√
Kensington Security Lock √√
Mini-card device √√
4 Chapter 1 Product description
Page 15

2 External component identification

Identifying hardware

To see a list of hardware installed in the computer, follow these steps:
Select Start > Control Panel > System and Security. Then, in the System area, click Device Manager.
You can also add hardware or modify device configurations using Device Manager.
NOTE: Windows® includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.
Identifying hardware
5
Page 16

Top components

TouchPad

Component Description
TouchPad on/off indicator To turn the TouchPad on and off, quickly double-tap the TouchPad
(1)
on/off indicator.
NOTE: When the TouchPad is enabled, the light is off.
TouchPad zone* Moves the pointer and selects or activates items on the screen.
(2)
Left TouchPad button* Functions like the left button on an external mouse.
(3)
Right TouchPad button* Functions like the right button on an external mouse.
(4)
*This table describes factory settings. To view or change pointing device preferences, select Start > Devices and Printers. Then, right-click the icon representing your device, and select Mouse settings.
There is an unmarked scroll zone inside the right edge of the TouchPad. To scroll up and down using the TouchPad vertical scroll zone, slide your finger up or down inside the right edge of the TouchPad. For more information about TouchPad features, refer to ”Using the TouchPad” section later in this guide.
6 Chapter 2 External component identification
Page 17

Lights

Component Description
(1)
(2)
(3)
(4)
TouchPad light
Caps lock light On: Caps lock is on.
Power light
Wireless light
Amber: The TouchPad is disabled.
Off: The TouchPad is enabled.
On: The computer is on.
Blinking: The computer is in the Sleep state.
Off: The computer is off or in Hibernation.
White: An integrated wireless device, such as a wireless
local area network (WLAN) device and/or a Bluetooth® device, is on.
Amber: All wireless devices are off.
Top components
7
Page 18

Button and speakers

Component Description
Speakers (2) Produce sound.
(1)
Power button
(2)
When the computer is off, press the button to turn on the
computer.
When the computer is on, press the button briefly to initiate
Sleep.
When the computer is in the Sleep state, briefly press the
button to exit Sleep.
When the computer is in Hibernation, briefly press the button
to exit Hibernation.
If the computer has stopped responding and Windows shutdown procedures are ineffective, press and hold the power button for at least 5 seconds to turn off the computer.
To learn more about your power settings, select Start > Control Panel > System and Security > Power Options.
8 Chapter 2 External component identification
Page 19

Keys

Component Description
esc key Displays system information when pressed in combination with the
(1)
fn key.
fn key
(2)
Windows logo key Displays the Windows Start menu.
(3)
Windows applications key Displays a shortcut menu for items beneath the pointer.
(4)
Navigation keys Navigate using the Up, Down, Left, and Right arrow keys.
(5)
Action keys Execute frequently used system actions.
(6)
Displays system information when pressed in combination with
the esc key.
Press in combination with an Up, Down, Left, or Right arrow
key to navigate a page or document.
Top components
9
Page 20

Display

Component Description
Internal microphone Records sound.
(1)
Integrated webcam Records video and captures still photographs.
(2)
Integrated webcam light On: The integrated webcam is in use.
(3)
10 Chapter 2 External component identification
Page 21

Front component

Component Description
Digital Media Slot Supports the following optional digital card formats:

Right-side components

Memory Stick (MS)
Memory Stick Pro (MSP)
MultiMediaCard (MMC)
Secure Digital (SD) Memory Card
xD-Picture Card (XD)
Component Description
Optical drive light Blinking: The optical drive is being accessed.
(1)
Optical drive Reads and writes to optical discs.
(2)
USB ports (2) Connect optional USB devices.
(3)
AC adapter/battery charging light
(4)
Power connector Connects an AC adapter.
(5)
White: The computer is connected to external power and the
battery is fully charged.
Blinking white: The computer is in the Sleep state.
Amber: A battery is charging.
Off: The computer is not connected to external power.
Front component
11
Page 22

Left-side components

Component Description
Security cable slot Attaches an optional security cable to the computer.
(1)
Vent Enables airflow to cool internal components.
(2)
NOTE: The security cable is designed to act as a deterrent, but it
may not prevent the computer from being mishandled or stolen.
NOTE: The computer fan starts up automatically to cool internal
components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
External monitor port Connects an external VGA monitor or projector.
(3)
RJ-45 (network) jack Connects a network cable.
(4)
HDMI port Connects an optional video or audio device, such as a high-
(5)
definition television, or any compatible digital or audio component.
USB port Connects optional USB devices.
(6)
Audio-in (microphone) jack Connects an optional computer headset microphone, stereo array
(7)
microphone, or monaural microphone.
Audio-out (headphone) jack Produces sound when connected to optional powered stereo
(8)
speakers, headphones, earbuds, a headset, or television audio.
Drive light On: The hard drive or the optical drive is in use.
(9)
12 Chapter 2 External component identification
Page 23

Rear component

Component Description
Vent Enables airflow to cool internal components.

Bottom components

NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Component Description
Battery bay Holds the battery.
(1)
Vents (6) Enable airflow to cool internal components.
(2)
NOTE: The computer fan starts up automatically to cool internal
components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Rear component
13
Page 24
Component Description
Battery release latch Releases the battery from the battery bay.
(3)
Memory module compartment Contains 2 memory module slots.
(4)
Hard drive bay Holds the hard drive and, on select models, the wireless LAN
(5)

Wireless antennas

At least 2 antennas send and receive signals from one or more wireless devices. These antennas are not visible from the outside of the computer.
(WLAN) module.
CAUTION: To prevent an unresponsive system, replace the
wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact technical support through Help and Support.
NOTE: For optimal transmission, keep the areas immediately around the antennas free from
obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region. These notices are located in Help and Support.
14 Chapter 2 External component identification
Page 25

Additional hardware components

Component Description
Power cord* Connects an AC adapter to an AC outlet.
(1)
AC adapter Converts AC power to DC power.
(2)
Battery* Powers the computer when the computer is not plugged into
(3)
external power.
*Batteries and power cords vary in appearance by country or region.
Additional hardware components
15
Page 26

3 Illustrated parts catalog

Serial number location

When ordering parts or requesting information, provide the computer serial number and model number located in the battery bay of the computer.
(1) Product name (4) Warranty period
(2) Serial number (5) Model description (select models)
(3) Product number
16 Chapter 3 Illustrated parts catalog
Page 27

Computer major components

Computer major components
17
Page 28
Item Description Spare part number
(1) Display assembly 33.78 cm (13.3-in) WXGA, HD, BrightView display assembly
NOTE: See
internal component spare part information.
For use in Compaq Presario CQ32 computers 608017-001
For use in HP G32 computers 628920-001
(2) Keyboard (for use in the United States)
(3) Top cover (includes Touchpad)
(4) Power connector cable (includes bracket)
(5) Optical Drive Mounting Kit (includes SATA cable, cable bracket, optical drive
bracket, and screws)
(6) USB board (includes cable)
(7) Speaker assembly (includes cable)
(8) System board (includes replacement thermal material; with 512-MB discrete graphics
memory)
System board (includes replacement thermal material, with 1-GB discrete graphics memory) 615842-001
(9) Processor (includes replacement thermal material)
Intel Core i5 processors, Dual Core
Display assembly components on page 24 for more display assembly
608018-001
608030-001
621884-001
608274-001
603922-001
608027-001
608029-001
580M (2.66-GHz turbo, 3-MB L3 cache) 625825-001
560M (2.66-GHz turbo, 3-MB L3 cache) 625824-001
540M (2.53-GHz, 3-MB L3 cache) 594188-001
520M (2.40-GHz, 3-MB L3 cache) 594187-001
460M (2.53-GHz turbo, 3-MB L3 cache) 626039-001
450M (2.40-GHz, 3-MB L3 cache) 613585-001
430M (2.26-GHz, 3-MB L3 cache) 597624-001
Intel Core i3 processors, Dual Core
380M (2.53-GHz, 3-MB L3 cache) 625823-001
370M (2.40-GHz, 3-MB L3 cache) 613584-001
350M (2.26-GHz, 3-MB L3 cache) 597623-001
Intel Pentium
P6200 (2.13-GHz, 3-MB L3 cache) 625831-001
P6100 (2.0-GHz, 3-MB L3 cache) 613587-001
P6000 (1.86-GHz, 3-MB L3 cache) 613586-001
(10) Fan/heat sink assembly (includes replacement thermal material)
18 Chapter 3 Illustrated parts catalog
608010-001
Page 29
Item Description Spare part number
(11) RTC battery (includes mounting adhesive)
(12) WLAN modules
Atheros AR9285 802.11 a/b/g/n 2x2 WiFi adapter
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentian, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Barbados, Belgium, Belize, Benin, Bhutan, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgeria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, Central African Republic, Chad, Chile, People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, Czech Republic, Zaire, Denmark, Djibouti, Dominica, Dominican Republic, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Korea-South, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, Nether Antilles, French Guiana, Aruba, British Virgin Islands, Bermuda, Syria, Guadeloupe, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagaascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Poland, Portugal, Republic of Moldova, Romania, rwanda, Samoa, San Marino, Sao tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Gren, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, Timor (East), Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, United Arab Emirates ,United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zambia, and Zimbabwe
449137-001
580101-002
Intel Centrino Wireless-N 1000 802.11b/g/n 1x2
For use in Andorra, Antigua and Barbuda, Argentina, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Barbados, Belgium, Bermuda, Bolivia, Bosnia and Herzegovina, Brazil, Brunei, Bulgaria, Canada, the Cayman Islands, Chile, People's Republic of China, Colombia, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, the Dominican Republic, Ecuador, Egypt, El Salvador, Estonia, Finland, France, French Guiana, Georgia, Germany, Ghana, Greece, Guadeloupe, Guam, Guatemala, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kenya, Kuwait, Kyrgyzstan, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malawi, Malaysia, Malta, Martinique, Mauritius, Mexico, Monaco, Montenegro, Morocco, the Nether Antilles, Netherlands, New Zealand, Nicaragua, Nigeria, Norway, Oman, Pakistan, Panama, Paraguay, Peru, Philippines, Poland, Portugal, Puerto Rico, Qatar, Romania, San Marino, Saudi Arabia, Senegal, Singapore, Slovakia, Slovenia, South Africa, South Korea, Spain, Sri Lanka, Sweden, Switzerland, Taiwan, Tanzania, Thailand, Trinidad and Tobago, Turkey, Ukraine, United Arab Emirates, United Kingdom, Uruguay, the US Virgin Islands, the United States, Venezuela, and Vietnam
593530-001
Computer major components
19
Page 30
Item Description Spare part number
Realtek RTL8191SE 802.11b/g/n WiFi Adapter
For use in Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Cayman Islands, Central African Republic, Chad, Chile, People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Iraq, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, Nether Antilles, Netherlands, New Zealand Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Poland, Portugal, Puerto Rico, Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Grenadine, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, United Arab Emirates, the United Kingdom, Uruguay, the US Virgin Islands, the United States, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
593533-001
Broadcom 4313AGN 802.11a/b/g/draft-n WiFi Adapter
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, the Cayman Islands, Central African Republic, Chad, People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea­Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Iraq, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Puerto Rico, Peru, Philippines, Poland, Portugal, Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, the United States, the US Virgin Islands, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
593836-001
20 Chapter 3 Illustrated parts catalog
Page 31
Item Description Spare part number
Broadcom 4313 802.11b/g/n 1x1 WiFi and 2070 Bluetooth 2.1 +EDR Combo Adapter
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, the Cayman Islands, Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Iraq, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, Puerto Rico, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, the US Virgin Islands, the United States, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
600370-001
Computer major components
21
Page 32
Item Description Spare part number
Realink RT3090BC4 802.11b/g/n 1x1 WiFi and Bluetooth 2.1+EDR Combo Adapter
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, the Cayman Islands, Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea­Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, Puerto Rico, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, the US Virgin Islands, the United States, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
602992-001
(13) Memory modules (PC3-10600, 1333-MHz)
4-GB 599092-001
2-GB 598859-001
1-GB 598856-001
(14) Power button board (includes cable and bracket)
(15) Bluetooth module
NOTE: The Bluetooth module cable is included in the Misc Cable Kit, spare part number
608009-001.
(16) Base enclosure (with modem cable and ODD cable)
(17) Battery
6-cell, 47-WHr (2.20-Ah) Li-ion 593553-001
6-cell, 55-WHr (2.55-Ah) Li-ion 593554-001
(18) Hard Drive Mounting Kit (includes retention screws, bracket screws, and hard drive
bracket)
(19) Hard drive (includes hard drive bracket)
NOTE: The hard drive cable is included in the Misc Cable Kit, spare part number 608009-001.
608276-001
537921-001
608008-001
608015-001
22 Chapter 3 Illustrated parts catalog
Page 33
Item Description Spare part number
500-GB, 7200 RPM 608014-001
320-GB, 7200 RPM 608013-001
250-GB, 7200 RPM 608012-001
160-GB solid-state drive 608011-001
(20) Optical drive (12.7 mm, SATA, fixed)
DVD±RW SuperMulti DL Drive with LightScribe 608021-001
Blu-ray ROM with LightScribe DVD±R/RW SuperMulti DL Drive 608022-001
Computer major components
23
Page 34

Display assembly components

Item Description Spare part number
(1) Display bezel (includes Mylar screw covers)
For use in Compaq Presario CQ32–branded computers 608020-001
For use in HP G32–branded computers 628918-001
(2) Webcam module
(3) Display panel, Brightview, high-definition, 33.78 cm (13.3-in)
24 Chapter 3 Illustrated parts catalog
608031-001
608019-001
Page 35
Item Description Spare part number
(4) Display hinge cover
(5) Display hinges
(6) Display cable kit
(7) Display WLAN antennas
(8) Display enclosure
For use in Compaq Presario CQ32–branded computers 608007-001
For use in HP G32–branded computers 628919-001

Plastics Kit

608275-001
608016-001
608272-001
608006-001
Item Description Spare part number
Plastics kit
Wireless/memory module mini-card compartment cover (includes captive screw)
(1)
Hard drive bay cover (includes captive screws)
(2)
608023-001
Plastics Kit
25
Page 36

Mass storage devices

Item Description Spare part number
(1) Optical drives (12.7 mm, SATA, fixed)
DVD±RW SuperMulti DL Drive with LightScribe 608021-001
Blu-ray ROM with LightScribe DVD±R/RW SuperMulti DL Drive 608022-001
(2) Hard drive (include hard drive bracket)
NOTE: The hard drive cable is included in the Misc Cable Kit, spare part number 608009-001.
500-GB, 7200 RPM 608014-001
320-GB, 7200 RPM 608013-001
250-GB, 7200 RPM 608012-001
160-GB solid-state drive 608011-001
Hard Drive Hardware Kit (includes retention screws, bracket screws, and hard drive bracket; not illustrated)
608015-001
26 Chapter 3 Illustrated parts catalog
Page 37

Miscellaneous parts

Description Spare part number
Smart AC adapter (90-W with power factor correction)
Power cord, AC, 3 wire, black, 1.83-m for use in the People's Republic of China
RTC battery
Rubber Feet Kit
Screw Kit
Phillips M2.0×3.0 screw
Phillips M2.0×4.0 screw
Phillips M2.5×3.0 broadhead screw
Phillips M2.5×4.0 screw
Phillips M2.5×5.0 screw
Phillips M2.5×7.0 screw
Phillips M2.5×8.0 screw
Phillips M3.0×3.0 screw
609940-001
490371-AA1
449137-001
608228-001
608026-001
Miscellaneous parts
27
Page 38

Sequential part number listing

Spare part number
449137-001 RTC battery
490371-AA1 Power cord, AC, 3-pin, black,1.83-m, for use in the People's Republic of China
537921-001 Bluetooth module without cable
580101-002 Atheros AR9285 802.11 a/b/g/n 2x2 WiFi adapter for use in Afghanistan, Albania, Algeria, Andorra,
Description
Angola, Antigua and Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Barbados, Belgium, Belize, Benin, Bhutan, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, Central African Republic, Chad, Chile, People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, Czech Republic, Zaire, Denmark, Djibouti, Dominica, Dominican Republic, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Korea­South, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, Nether Antilles, French Guiana, Aruba, British Virgin Islands, Bermuda, Syria, Guadeloupe, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Poland, Portugal, Republic of Moldova, Romania, Rwanda, Samoa, San Marino, Sao tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Gren, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, Timor (East), Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, United Arab Emirates, United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zambia, and Zimbabwe
593530-001 Intel Centrino Wireless-N 1000 802.11b/g/n 1x2 for use in Andorra, Antigua and Barbuda, Argentina,
Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Barbados, Belgium, Bermuda, Bolivia, Bosnia and Herzegovina, Brazil, Brunei, Bulgaria, Canada, the Cayman Islands, Chile, People's Republic of China, Colombia, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, the Dominican Republic, Ecuador, Egypt, El Salvador, Estonia, Finland, France, French Guiana, Georgia, Germany, Ghana, Greece, Guadeloupe, Guam, Guatemala, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kenya, Kuwait, Kyrgyzstan, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malawi, Malaysia, Malta, Martinique, Mauritius, Mexico, Monaco, Montenegro, Morocco, the Nether Antilles, Netherlands, New Zealand, Nicaragua, Nigeria, Norway, Oman, Pakistan, Panama, Paraguay, Peru, Philippines, Poland, Portugal, Puerto Rico, Qatar, Romania, San Marino, Saudi Arabia, Senegal, Singapore, Slovakia, Slovenia, South Africa, South Korea, Spain, Sri Lanka, Sweden, Switzerland, Taiwan, Tanzania, Thailand, Trinidad and Tobago, Turkey, Ukraine, United Arab Emirates, United Kingdom, Uruguay, the US Virgin Islands, the United States, Venezuela, and Vietnam
28 Chapter 3 Illustrated parts catalog
Page 39
Spare part number
593533-001 Realtek RTL8191SE 802.11b/g/n WiFi Adapter for use in Albania, Algeria, Andorra, Angola, Antigua and
593553-001 6-cell, 47-Whr (2.20-Ah) Li-ion battery
Description
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Cayman Islands, Central African Republic, Chad, Chile, People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Iraq, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, Nether Antilles, Netherlands, New Zealand Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Poland, Portugal, Puerto Rico, Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Grenadine, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, United Arab Emirates, the United Kingdom, Uruguay, the US Virgin Islands, the United States, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
593554-001 6-cell 55-Whr (2.55Ah) Li-ion battery
593836-001 Broadcom 4313AGN 802.11a/b/g/draft-n WiFi Adapter for use in Afghanistan, Albania, Algeria,
Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, the Cayman Islands, Central African Republic, Chad, People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Iraq, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Puerto Rico, Peru, Philippines, Poland, Portugal, Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, the United States, the US Virgin Islands, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
594187-001 Intel Core i5 520M Dual Core processor (2.40-GHz, 3-MB L3 cache)
594188-001 Intel Core i5 540M Dual Core processor (2.53-GHz, 3-MB L3 cache)
597623-001 Intel Core i3 350M Dual-Core processor (2.26-GHz, 3-MB L3 cache)
Sequential part number listing
29
Page 40
Spare part number
597624-001 Intel Core i5 430M Dual Core processor (2.26-GHz, 3-MB L3 cache)
598856-001 Memory module, 2-GB, PC3 10600, 1333-MHz
598859-001 Memory module, 1-GB, PC3 10600, 1333-MHz
599092-001 Memory module, 4-GB, PC3 10600, 1333-MHz
600370-001 Broadcom 4313 802.11b/g/n 1x1 WiFi and 2070 Bluetooth 2.1+EDR Combo Adapter for use in
Description
Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, the Cayman Islands, Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Iraq, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, Puerto Rico, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, the US Virgin Islands, the United States, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
602992-001 Realink RT3090BC4 802.11b/g/n 1x1 WiFi and Bluetooth 2.1+EDR Combo Adapter for use in
Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, the Cayman Islands, Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, Puerto Rico, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, the US Virgin Islands, the United States, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
603922-001 USB board
30 Chapter 3 Illustrated parts catalog
Page 41
Spare part number
608006-001 Display WLAN antennas
608007-001 Display enclosure for use in Compaq Presario CQ32 computers
608008-001 Base enclosure
608009-001 Misc Cable Kit (includes Bluetooth module cable and hard drive cable)
608010-001 Fan/heat sink
608011-001 160-GB solid-state hard drive
608012-001 250-GB, 7200 RPM hard drive
608013-001 320-GB, 7200 RPM hard drive
608014-001 500-GB, 7200 RPM hard drive
608015-001 Hard drive hardware kit (includes retention screws, bracket screws, and hard drive bracket)
608016-001 Display bracket (with hinges)
Description
608017-001
608018-001 Keyboard for use in the United States
608019-001
608020-001 Display bezel (includes Mylar screw covers) for use in Compaq Presario CQ32 computers
608021-001 DVD±RW SuperMulti DL Drive with LightScribe
608022-001 Blu-ray ROM with LightScribe DVD±R/RW SuperMulti DL Drive
608023-001 Plastics kit (with hard drive compartment cover and memory/wireless compartment cover)
608026-001 Screw Kit
608027-001 Speaker assembly (includes cable)
608029-001 System board with 512-MB of discrete graphics memory (includes replacement thermal material)
608030-001 Top cover (includes Touchpad and bracket, button board, and cable)
608031-001 Webcam module
608228-001 Rubber kit
608272-001 Display cable kit
608274-001 Optical Drive Mounting Kit (includes SATA cable, cable bracket, optical drive bracket, and screws)
33.78 cm (13.3-in) WXGA Brightview display assembly for use in Compaq Presario CQ32 computers
33.78 cm (13.3-in) display panel, high definition
608275-001 Display hinge cover
608276-001 Power button board (includes cable and bracket)
609940-001 90-W Smart AC adapter
613584-001 Intel Core i3 370M Dual Core (2.40-GHz, 3-MB L3 cache)
613585-001 Intel Core i5 450M Dual Core processor (2.40-GHz, 3-MB L3 cache)
613586-001 Intel Pentium P6000 processor (1.86-MHz, 3-MB L3 cache)
Sequential part number listing
31
Page 42
Spare part number
613587-001 Intel Pentium P6100 processor (2.0-GHz, 3-MB L3 cache
615842-001 System board with 1-GB discrete graphics memory (includes replacement thermal material)
621884-001 Power connector with cable (includes bracket)
625823-001 Intel Core i3 380M Dual Core processor (2.53-GHz, 3-MB L3 cache)
625824-001 Intel Core i5 560M Dual Core processor (2.66–3.2-GHz, 3-MB L3 cache)
625825-001 Intel Core i5 580M Dual Core processor (2.66–3.3-GHz, -3MB, L3 cache)
625831-001 Intel Pentium P6200 processor (2.13-GHz, 3-MB, L3 cache)
626039-001 Intel Core i5 460M Dual Core processor (2.53-GHz, 3-MB L3 cache)
628918-001 Display bezel (includes Mylar screw covers) for use in HP G32–branded computers
628919-001 Display enclosure for use in HP G32–branded computers
Description
628920-001
33.78 cm (13.3-in) WXGA Brightview display assembly for use in HP G32–branded computers
32 Chapter 3 Illustrated parts catalog
Page 43
4 Removal and replacement
procedures

Preliminary replacement requirements

Tools required

You will need the following tools to complete the removal and replacement procedures:
Flat-bladed screwdriver
Magnetic screwdriver
Phillips P0 and P1 screwdrivers

Service considerations

The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Preliminary replacement requirements
33
Page 44
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective packaging and label the package “FRAGILE.”
34 Chapter 4 Removal and replacement procedures
Page 45

Grounding guidelines

Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal cycle. Or the device may function normally for a while, then degrade in the internal layers, reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event 10% 40% 55%
Walking across carpet 35,000 V 15,000 V 7,500 V
Walking across vinyl floor 12,000 V 5,000 V 3,000 V
Motions of bench worker 6,000 V 800 V 400 V
Removing DIPS from plastic tube 2,000 V 700 V 400 V
Removing DIPS from vinyl tray 11,500 V 4,000 V 2,000 V
Removing DIPS from Styrofoam 14,500 V 5,000 V 3,500 V
Removing bubble pack from PCB 26,500 V 20,000 V 7,000 V
Packing PCBs in foam-lined box 21,000 V 11,000 V 5,000 V
Preliminary replacement requirements
35
Page 46
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
Place items on a grounded surface before removing items from their containers.
Always be properly grounded when touching a component or assembly.
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive
foam.
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that
mechanized equipment used for moving materials is wired to ground and that proper materials are selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
Cover the workstation with approved static-shielding material.
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle
these items only at static-free workstations.
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before inserting or removing connectors or test equipment.
36 Chapter 4 Removal and replacement procedures
Page 47
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps)
can be used at standing workstations and are compatible with most types of shoes or boots. On conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the operator and ground. To be effective, the conductive strips must be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
Antistatic tape
Antistatic smocks, aprons, and sleeve protectors
Conductive bins and other assembly or soldering aids
Non-conductive foam
Conductive tabletop workstations with ground cords of one megohm resistance
Static-dissipative tables or floor mats with hard ties to the ground
Field service kits
Static awareness labels
Material-handling packages
Non-conductive plastic bags, tubes, or boxes
Metal tote boxes
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material Use Voltage protection level
Antistatic plastic Bags 1,500 V
Carbon-loaded plastic Floor mats 7,500 V
Metallized laminate Floor mats 5,000 V
Preliminary replacement requirements
37
Page 48

Component replacement procedures

This chapter provides removal and replacement procedures.
There are as many as 75 screws, in 12 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement.

Serial number

The serial number label, located in the battery bay of the computer, provides important information that you may need when contacting technical support.
Product name (1). This is the product name affixed to the front of the computer.
Serial number (s/n) (2). This is an alphanumeric identifier that is unique to each product.
Part number/Product number (p/n) (3). This number provides specific information about the product's hardware components. The part number helps a service technician to determine what components and parts are needed.
Warranty period (4). This number describes the duration (in years) of the warranty period for the computer.
Model description (5). This is the alphanumeric identifier used to locate documents, drivers, and support for the computer.
38 Chapter 4 Removal and replacement procedures
Page 49

Computer feet

Description Spare part number
Rubber Feet Kit 608228-001
The computer feet are adhesive-backed rubber pads. The feet attach to the base enclosure in the locations illustrated below.
Component replacement procedures
39
Page 50

Battery

Description Spare part number
6-cell, 47-WHr (2.20-Ah) Li-ion 593553-001
6-cell, 55-WHr (2.55Ah) Li-ion 593554-001
Before disassembling the computer, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery:
Turn the computer upside down on a flat surface.
1.
2. Slide the battery release latch (1) to release the battery.
3. Pivot the battery (2) upward and lift it out of the computer (3).
To insert the battery, insert the rear edge of the battery into the battery bay and pivot the front edge downward until the battery is seated. The battery release latch automatically locks the battery into place.
40 Chapter 4 Removal and replacement procedures
Page 51

Memory module

Description Spare part number
4-GB, PC3 10600, 1333-MHz 599092-001
2-GB, PC3 10600, 1333-MHz 598856-001
1-GB, PC3 10600, 1333-MHz 598859-001
Before removing the memory module, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Battery on page 40).
Remove the memory module:
Turn the computer upside down with the front toward you.
1.
2. Remove the Phillips PM2.5×5.0 screw (1) that secures the memory/wireless module compartment
cover to the computer.
Component replacement procedures
41
Page 52
3. Lift the cover (2) and remove it (3). The memory/wireless compartment cover is included in the
Plastics Kit, spare part number 608023-001.
4. Spread the retaining tabs (1) on each side of the memory module slot to release the memory
module. (The edge of the module opposite the slot rises away from the computer.)
42 Chapter 4 Removal and replacement procedures
Page 53
5. Remove the module (2) by pulling it away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the
memory module slot.
Reverse this procedure to install a memory module.
Component replacement procedures
43
Page 54

RTC battery

Description Spare part number
RTC battery 449137-001
Before removing the RTC battery, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Hard drive cover (see
5.
Battery on page 40).
Hard drive on page 50)
Remove the RTC battery:
Turn the system board upside down.
1.
2. Release the RTC battery from the clips on the system board (1).
3. Remove the RTC battery (2).
Reverse this procedure to install the RTC battery.
44 Chapter 4 Removal and replacement procedures
Page 55

WLAN module

NOTE: The WLAN module and the WWAN module are not interchangeable.
Description Spare part
number
Atheros AR9285 802.11 a/b/g/n 2x2 WiFi adapter
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentian, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Barbados, Belgium, Belize, Benin, Bhutan, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgeria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, Central African Republic, Chad, Chile, People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, Czech Republic, Zaire, Denmark, Djibouti, Dominica, Dominican Republic, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Korea-South, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, Nether Antilles, French Guiana, Aruba, British Virgin Islands, Bermuda, Syria, Guadeloupe, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagaascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Poland, Portugal, Republic of Moldova, Romania, rwanda, Samoa, San Marino, Sao tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Gren, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, Timor (East), Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, United Arab Emirates ,United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zambia, and Zimbabwe
Intel Centrino Wireless-N 1000 802.11b/g/n 1x2
For use in Andorra, Antigua and Barbuda, Argentina, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Barbados, Belgium, Bermuda, Bolivia, Bosnia and Herzegovina, Brazil, Brunei, Bulgaria, Canada, the Cayman Islands, Chile, People's Republic of China, Colombia, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, the Dominican Republic, Ecuador, Egypt, El Salvador, Estonia, Finland, France, French Guiana, Georgia, Germany, Ghana, Greece, Guadeloupe, Guam, Guatemala, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kenya, Kuwait, Kyrgyzstan, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malawi, Malaysia, Malta, Martinique, Mauritius, Mexico, Monaco, Montenegro, Morocco, the Nether Antilles, Netherlands, New Zealand, Nicaragua, Nigeria, Norway, Oman, Pakistan, Panama, Paraguay, Peru, Philippines, Poland, Portugal, Puerto Rico, Qatar, Romania, San Marino, Saudi Arabia, Senegal, Singapore, Slovakia, Slovenia, South Africa, South Korea, Spain, Sri Lanka, Sweden, Switzerland, Taiwan, Tanzania, Thailand, Trinidad and Tobago, Turkey, Ukraine, United Arab Emirates, United Kingdom, Uruguay, the US Virgin Islands, the United States, Venezuela, and Vietnam
580101-002
593530-001
Component replacement procedures
45
Page 56
Description Spare part
number
Realtek RTL8191SE 802.11b/g/n WiFi Adapter
For use in Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Cayman Islands, Central African Republic, Chad, Chile, People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Iraq, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, Nether Antilles, Netherlands, New Zealand Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Poland, Portugal, Puerto Rico, Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Grenadine, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, United Arab Emirates, the United Kingdom, Uruguay, the US Virgin Islands, the United States, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Broadcom 4313AGN 802.11a/b/g/draft-n WiFi Adapter
593533-001
593836-001
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, the Cayman Islands, Central African Republic, Chad, People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Iraq, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Puerto Rico, Peru, Philippines, Poland, Portugal, Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, the United States, the US Virgin Islands, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
46 Chapter 4 Removal and replacement procedures
Page 57
Description Spare part
number
Broadcom 4313 802.11b/g/n 1×1 WiFi and 2070 Bluetooth 2.1+EDR Combo Adapter
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, the Cayman Islands, Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Iraq, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, Puerto Rico, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, the US Virgin Islands, the United States, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Realink RT3090BC4 802.11b/g/n 11 WiFi and Bluetooth 2.1+EDR Combo Adapter
600370–001
602992-001
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cape Verde, the Cayman Islands, Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, Puerto Rico, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, the US Virgin Islands, the United States, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Component replacement procedures
47
Page 58
Before removing the WLAN module, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the memory/wireless module compartment cover (see
5.
Battery on page 40).
Memory module on page 41).
Remove the WLAN module:
Turn the computer upside down with the front toward you.
1.
2. Disconnect the two WLAN antenna cables (1) from the WLAN module.
3. Remove the two Phillips PM2.0×4.0 screws (2) that secure the WLAN module to the computer.
(The edge of the module opposite the slot rises away from the computer.)
48 Chapter 4 Removal and replacement procedures
Page 59
4. Remove the WLAN module (3) by pulling it away from the slot at an angle.
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless
module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact technical support through Help and Support.
NOTE: WLAN modules are designed with a notch (4) to prevent incorrect insertion into the
WLAN module slot.
Reverse this procedure to install a WLAN module.
Component replacement procedures
49
Page 60

Hard drive

NOTE: All hard drive spare part kits include a hard drive bracket.
NOTE: The hard drive cable is included in the Misc Cable Kit, spare part number 608009-001.
Description Spare part number
500-GB, 7200 RPM 608014-001
320-GB, 7200 RPM 608013-001
250-GB, 7200 RPM 608012-001
160-GB solid-state drive 608011-001
Hard drive hardware kit (includes screws and hard drive bracket) 608015-001
Before removing the hard drive, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the memory/wireless module compartment cover (see
5.
Battery on page 40).
Memory module on page 41)
Remove the hard drive:
Position the computer with the front toward you.
1.
2. Remove the Phillips PM2.5×5.0 screw (1) that secures the hard drive cover to the computer.
50 Chapter 4 Removal and replacement procedures
Page 61
3. Lift the hard drive cover (2) and remove it from the computer (3). The hard drive cover is included
in the Plastics Kit, spare part number 608023-001.
4. Disconnect the hard drive cable from the system board (1).
5. Remove the four Phillips PM2.5×8.0 screws (2) that secure the hard drive to the computer.
Component replacement procedures
51
Page 62
6. Use the Mylar tab to lift the hard drive out of the hard drive bay (3).
7. If it is necessary to replace the hard drive bracket, remove the four Phillips PM3.0×3.0 screws (1)
that secure the hard drive bracket to the hard drive
8. Lift the bracket (2) straight up and off the hard drive.
Reverse this procedure to install the hard drive.
52 Chapter 4 Removal and replacement procedures
Page 63

Optical drive

Description Spare part number
DVD±RW SuperMulti DL Drive with LightScribe 608021-001
Blu-ray ROM with LightScribe DVD±R/RW SuperMulti DL Drive 608022-001
Before removing the optical drive, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the memory/wireless module compartment cover (see
5.
Remove the hard drive cover (see
6.
Battery on page 40).
Memory module on page 41)
Hard drive on page 50)
Remove the optical drive:
Position the computer upside down with the front toward you.
1.
2. Remove the Phillips PM2.5x5.0 screw (1) that secures the optical drive to the computer.
3. Use a flat-bladed screwdriver or similar tool to push the drive bracket to the left (2) to release the
optical drive.
4. Remove the optical drive (3).
If it is necessary to replace the optical drive bracket, position the optical drive with the optical
5.
drive bracket toward you.
Component replacement procedures
53
Page 64
6. Remove the two Phillips PM2.0×3.0 screws (1) that secure the optical drive bracket to the optical
7. Remove the optical drive bracket (2).
Reverse the above procedure to reassemble and install the optical drive.

Top cover

Description Spare part number
Top cover (includes Touchpad and bracket, button board, and cable) 608030-001
drive.
Before removing the top cover, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the following components:
4.
Battery (see
a.
Hard drive (see
b.
Optical drive (see
c.
Battery on page 40).
Hard drive on page 50).
Optical drive on page 53).
Remove the top cover:
Turn the computer upside down with the front toward you.
1.
Remove the following screws that secure the top cover to the base enclosure:
2.
(1) 5 Phillips PM2.0×4.0 screws
(2) 1 Phillips PM2.5×7.0 screw
(3) 2 Phillips PM2.5×5.0 screws
54 Chapter 4 Removal and replacement procedures
Page 65
Remove the following screws that secure the top cover to the base enclosure:
3.
(1) 2 rubber feet
(2) 2 Phillips PM2.0×3.0 screws (in optical drive bay)
(3) 2 Phillips PM2.5×5.0 screws (in hard drive bay)
(4) 10 Phillips PM2.5×8.0 screws (2 of the screws are under the feet)
Component replacement procedures
55
Page 66
Turn the computer right-side up with the front toward you.
4.
Open the computer as far as possible.
5.
6. Pry up the edges of the top cover (1), and then lift it up off the base enclosure (2) enough to gain
access to the cables.
Release the ZIF connector to which the TouchPad cable is connected and disconnect the cable
7.
from the system board (1).
56 Chapter 4 Removal and replacement procedures
Page 67
Release the ZIF connector to which the TouchPad button board cable is connected and disconnect
8.
the cable from the system board (2).
Remove the top cover from the base enclosure.
9.
Reverse this procedure to install the top cover.
Component replacement procedures
57
Page 68

Keyboard

Description Spare part number
Keyboard for use in the United States 608018-001
Before removing the keyboard, follow these steps:
1.
2.
3.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the memory/wireless compartment cover (see
5.
Remove the hard drive cover (see
6.
Remove the top cover (see
7.
Battery on page 40).
Hard drive on page 50).
Top cover on page 54).
Remove the keyboard:
Turn the top cover upside down.
1.
Memory module on page 41).
58 Chapter 4 Removal and replacement procedures
Page 69
Slide the keyboard clips off the bottom of the keyboard.
2.
3. Pry to edges of the keyboard from the top cover (1), and the lift the top of the keyboard up from
the top cover (2).
4. Slide the keyboard cable through the slot in the top cover (3).
Reverse this procedure to install the keyboard.
Component replacement procedures
59
Page 70

USB board

Description Spare part number
USB board (includes cable) 603922–001
Before removing the USB board, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Hard drive (see
a.
Optical drive (see
b.
Top cover (see
c.
Battery on page 40).
Hard drive on page 50)
Optical drive on page 53)
Top cover on page 54)
Remove the USB board:
Position the computer upright with the right side toward you.
1.
If necessary, move the power connector cable aside to gain access to the USB board screw.
2.
3. Disconnect the USB board cable (1) from the system board.
4. Remove the Phillips PM2.5×8.0 screw (2) that secures the USB board to the base enclosure.
60 Chapter 4 Removal and replacement procedures
Page 71
5. Lift the USB board (3) straight up to remove it from the computer.
Reverse this procedure to install the USB board.
Component replacement procedures
61
Page 72

Speaker assembly

Description Spare part number
Speaker assembly 608027-001
Before removing the speaker assembly, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Optical drive (see
a.
Keyboard (see
b.
Top cover (see
c.
Battery on page 40).
Optical drive on page 53)
Keyboard on page 58)
Top cover on page 54)
Remove the speaker assembly:
Position the computer upright with the front toward you.
1.
2. Remove the tape that secures the cable to the system board (1).
3. Disconnect the speaker cable from the system board (2).
4. Remove the tape that secures the cable to the system board (3).
5. Remove the Phillips PM2.5×5.0 screw (4) that secures the speaker assembly to the base
enclosure.
6. Lift the left speaker (5) straight up to remove it from the base enclosure.
62 Chapter 4 Removal and replacement procedures
Page 73
7. Lift the right speaker (6) straight up to remove it from the base enclosure.
Reverse this procedure to install the speaker assembly.
Component replacement procedures
63
Page 74

Bluetooth module

NOTE: The Bluetooth module cable is included in the Misc Cable Kit, spare part number
608009-001.
Description Spare part number
Bluetooth module 537921-001
Before removing the Bluetooth module, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Hard drive (see
a.
Optical drive (see
b.
Top cover (see
c.
Battery on page 40).
Hard drive on page 50)
Optical drive on page 53)
Top cover on page 54)
Remove the Bluetooth module:
Position the computer upright with the front toward you.
1.
2. Lift the tape that secures the Bluetooth module cable to the system board (1).
3. Disconnect the cable (2) from the system board.
64 Chapter 4 Removal and replacement procedures
Page 75
4. Pull the clip that holds the Bluetooth module (3), and then remove the module from the base
enclosure (4).
Reverse the above procedure to install the Bluetooth module.
Component replacement procedures
65
Page 76

Power connector cable

Description Spare part number
Power connector cable (includes cable and connector) 621884-001
Before removing the power connector cable, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Hard drive (see
a.
Optical drive (see
b.
Top cover (see
c.
Battery on page 40).
Hard drive on page 50)
Optical drive on page 53)
Top cover on page 54))
Remove the power connector cable:
Turn the computer upright with the right side toward you.
1.
2. Disconnect the power connector cable (1) from the system board.
3. Remove the Phillips PM2.0×4.0 screw (2) that secures the power connector cable to the base
enclosure.
4. Remove the bracket from atop the connector (3).
66 Chapter 4 Removal and replacement procedures
Page 77
5. Remove the power connector (4) from the base enclosure.
Reverse this procedure to install the power connector cable.
Component replacement procedures
67
Page 78

Optical drive connector

Description Spare part number
Optical Drive Mounting Kit (includes SATA cable, cable bracket, optical drive bracket, and screws)
608274-001
Before removing the optical drive connector, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Hard drive (see
a.
Optical drive (see
b.
Top cover (see
c.
USB board (
d.
USB board on page 60).
Battery on page 40).
Hard drive on page 50)
Optical drive on page 53)
Top cover on page 54)
Speaker assembly(
e.
Speaker assembly on page 62).
Remove the optical drive connector:
Turn the computer upright with the right side toward you.
1.
2. Remove the tape that secures the cable to the base enclosure (1).
3. Disconnect the optical drive connector from the system board (2).
4. Remove the Phillips PM2.0×3.0 screw (3) that secures the optical drive connector to the base
enclosure.
5. Lift the bracket from the base enclosure (4).
68 Chapter 4 Removal and replacement procedures
Page 79
6. Remove the optical drive connector assembly (5) from the base enclosure.
Reverse this procedure to install the optical drive connector.
Component replacement procedures
69
Page 80

Power button board

Description Spare part number
Power button board (with cable and bracket)
608276-001
Before removing the power button board, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Hard drive (see
a.
Optical drive (see
b.
Top cover (see
c.
Speaker assembly (
d.
Battery on page 40).
Hard drive on page 50)
Optical drive on page 53)
Top cover on page 54)
Speaker assembly on page 62).
Remove the power button board:
Turn the computer upright with the right side toward you.
1.
2. Disconnect the cable from the system board (1).
3. Remove the Phillips PM2.0×3.0 screw (2) that secures the power button board to the top cover.
70 Chapter 4 Removal and replacement procedures
Page 81
4. Remove the power button board (3).
Reverse this procedure to install the power button board.
Component replacement procedures
71
Page 82

Display assembly

Description Spare part number
33.78 cm (13.3-in) WXGA Brightview display assembly for use in Compaq Presario CQ32–
branded computers
33.78 cm (13.3-in) WXGA Brightview display assembly for use in HP G32–branded computers
608017-001
628920-001
Before removing the display assembly, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Disconnect the wireless antenna cables from the WLAN module (see
5.
Remove the following components:
6.
Optical drive (see
a.
WLAN module (see
b.
Battery on page 40).
WLAN module on page 45).
Optical drive on page 53)
WLAN module on page 45)
Top cover (see
c.
USB board (
d.
Top cover on page 54)
USB board on page 60).
Remove the display assembly:
Turn the computer display-side up, with the front toward you.
1.
Open the display as far as possible.
2.
3. Disconnect the display panel cable (1) from the system board.
4. Remove the two Phillips PM2.5×8.0 screws (2) that secure the display assembly to the computer.
CAUTION: Support the display assembly when removing the display screws in the following
steps. Failure to support the display assembly can result in damage to the assembly and other components.
5. Remove the wireless antenna cables (3) from the hole and clips built into the base enclosure.
72 Chapter 4 Removal and replacement procedures
Page 83
6. Remove the display assembly (4).
If it is necessary to replace any of the display assembly internal components, remove the following
7.
screw covers and screws.
(1) Two Mylar screw covers on the display bezel bottom edge
(2) Two Phillips PM2.5×4.0 screws
8. Flex the inside edge of the top (1), the left and right sides (2), and the bottom (3) of the display
bezel until the bezel disengages from the display back cover.
Component replacement procedures
73
Page 84
9. Remove the display bezel (4). The display bezel is available using spare part numbers
608020-001 (for use in Compaq Presario CQ32-branded computers), and 628918-001 (for use in HP G32-branded computers).
If it is necessary to replace the webcam module, remove the tape from the webcam module
10.
connector (1), disconnect the webcam cable (2) from the module. and lift the webcam (left side first) to disengage the double-sided tape on the display back cover (3). The webcam is available using spare part number 608031-001.
If it is necessary to replace the display panel, remove the two Phillips PM2.5×3.0 broadhead
11.
screws (1) and the two Phillips PM2.5×4.0 screws (2) that secure the display panel to the display enclosure.
74 Chapter 4 Removal and replacement procedures
Page 85
12. Lift up the bottom of the panel (3), and them remove the panel from the enclosure (4). The display
panel is available using the spare part number 608019-001.
If it is necessary to replace the display cable, follow these steps:
13.
Turn the display panel upside down in front of you.
a.
b. Disengage the webcam cable from the glue securing it to the back of the display (1).
c. Peel back the tape that secures the display cable to the display (2).
d. Disconnect the display cable from the display (3).
e. Remove the display cable from the display (4).
Component replacement procedures
75
Page 86
The display cable is available in the display cable kit, spare part number 608272-001.
14. If it is necessary to replace the display hinges, remove the four Phillips PM2.0×3.0 screws (1) that
secure the hinges to the display.
15. Remove the display hinges (2) from the display. Display hinges are available using spare part
number 608016-001.
16. If it is necessary to replace the wireless antennas and cables, remove the adhesive strip (1) that
secures each antenna to the display back cover.
17. Remove the antennas (2) from the clips (3) built into the display enclosure.
76 Chapter 4 Removal and replacement procedures
Page 87
18. Remove the wireless antennas and cables (4) from the display enclosure. The wireless antennas
and cables are included in the display cable kit, spare part number 608272-001.
Reverse this procedure to reassemble and install the display assembly.
Component replacement procedures
77
Page 88

System board

NOTE: All system board spare part kits include replacement thermal material.
Description Spare part number
System board with 512-MB of discrete graphics memory 608029-001
System board with 1-GB of discrete graphics memory 615842-001
When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board:
RTC battery (see
Memory modules (see
WLAN module (see
Fan/heat sink assembly (see
Processor (see
RTC battery on page 44)
Memory module on page 41)
WLAN module on page 45)
Fan/heat sink assembly on page 80)
Processor on page 83)
Before removing the system board, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Hard drive (see
a.
WLAN module (see
b.
Battery on page 40).
Hard drive on page 50)
WLAN module on page 45)
Optical drive (see
c.
Top cover (see
d.
Speaker assembly (see
e.
Display assembly (see
f.
USB board (see
g.
Optical drive on page 53)
Top cover on page 54)
Speaker assembly on page 62)
Display assembly on page 72)
USB board on page 60)
78 Chapter 4 Removal and replacement procedures
Page 89
Power connector cable (see
h.
Power connector cable on page 66)
Display (see
i.
Turn the computer upright with the left side toward you.
1.
Display assembly on page 72)
2. Remove the two Phillips PM2.5×5.0 screws (1) that secure the system board to the computer.
3. Loosen the captive screw in the fan sink (2) that secures the system board.
4. Lift the right side of the system board (3).
5. Release the system board by sliding it to the right at an angle (4) until the connectors on the left
side of the system board clear the base enclosure, and then remove the system board.
Reverse the preceding procedure to install the system board.
Component replacement procedures
79
Page 90

Fan/heat sink assembly

NOTE: All fan/heat sink assembly spare part kits include replacement thermal material.
Description Spare part number
Fan/heat sink assembly 608010-001
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the right
side and rear panel of the computer. The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to turn on automatically when high temperature conditions exist. These conditions are affected by high external temperatures, system power consumption, power management/battery conservation configurations, battery fast charging, and software requirements. Exhaust air is displaced through the ventilation grill located on the left side of the computer.
Before removing the fan/heat sink assembly, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Hard drive (see
a.
WLAN module (see
b.
Optical drive (see
c.
Top cover (see
d.
Speaker assembly (see
e.
Power connector cable (see
f.
USB board (see
g.
Display assembly (see
h.
System board (see
i.
Battery on page 40).
Hard drive on page 50)
WLAN module on page 45)
Optical drive on page 53)
Top cover on page 54)
Speaker assembly on page 62)
Power connector cable on page 66)
USB board on page 60)
Display assembly on page 72)
System board on page 78)
Remove the fan/heat sink assembly:
Turn the system board upside down.
1.
80 Chapter 4 Removal and replacement procedures
Page 91
Disconnect the fan cable from the system board.
2.
3. Follow the sequence embossed on heat sink to loosen the six captive screws (1) that secure the
fan/heat sink assembly to the system board.
NOTE: Due to the adhesive quality of the thermal material located between the fan/heat sink
assembly and system board components, it may be necessary to move the fan/heat sink assembly from side to side to detach the assembly.
Component replacement procedures
81
Page 92
4. Remove the fan/heat sink assembly from the system board (2).
The thermal material must be thoroughly cleaned from the affected surfaces on the system board (1), (3) and from the affected surfaces on the fan/heat sink assembly (2), (4) each time the fan/heat sink assembly is removed. Thermal pads and thermal paste must be installed on all surfaces before the fan/ heat sink assembly is reinstalled.
NOTE: Thermal pads and thermal paste are included with all fan/heat sink assembly, system board,
and processor spare part kits.
The following illustration shows the locations for thermal material.
Reverse this procedure to install the fan/heat sink assembly.
82 Chapter 4 Removal and replacement procedures
Page 93

Processor

NOTE: All processor spare part kits include replacement thermal material.
Description Spare part number
Intel Core i5 580M Dual Core processor (2.66-GHz, 3-MB L3 cache) 625825-001
Intel Core i5 560M Dual Core processor (2.66-GHz, 3-MB L3 cache) 625824-001
Intel Core i5 540M Dual Core processor (2.53-GHz, 3-MB L3 cache) 594188-001
Intel Core i5 520M Dual Core processor (2.40-GHz, 3-MB L3 cache) 594187-001
Intel Core i5 460M Dual Core processor (2.53-GHz, 3-MB L3 cache) 626039-001
Intel Core i5 450M Dual Core processor (2.40-GHz, 3-MB L3 cache) 613585-001
Intel Core i5 430M Dual Core processor (2.26-GHz, 3-MB L3 cache) 597624-001
Intel Core i3 380M Dual Core processor (2.53-GHz, 3-MB L3 cache) 625823-001
Intel Core i3 370M Dual Core (2.40-GHz, 3-MB L3 cache) 613584-001
Intel Core i3 350M Dual Core (2.26-GHz, 3-MB L3 cache) 597623-001
Intel Pentium P6200 processor (2.13-GHz, 3-MB L3 cache) 625831-001
Intel Pentium P6100 processor (2.0-GHz, 3-MB L3 cache) 613587-001
Intel Pentium P6000 (1.86-MHz, 3-MB L3 cache) 613586-001
Before removing the processor, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
3.
and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Hard drive (see
a.
WLAN module (see
b.
Optical drive (see
c.
Top cover (see
d.
Speaker assembly (see
e.
Battery on page 40).
Hard drive on page 50)
WLAN module on page 45)
Optical drive on page 53)
Top cover on page 54)
Speaker assembly on page 62)
Power connector cable (see
f.
USB board (see
g.
Power connector cable on page 66)
USB board on page 60).
Component replacement procedures
83
Page 94
Display assembly (see
h.
Display assembly on page 72)
System board (see
i.
Fan/heat sink assembly (see
j.
System board on page 78)
Fan/heat sink assembly on page 80)
Remove the processor:
1. Turn the processor locking screw (1) one-half turn counterclockwise until you hear a click.
2. Lift the processor (2) straight up and remove it.
NOTE: The gold triangle (3) on the processor must be aligned with the triangle icon (4)
embossed on the processor socket when you install the processor.
Reverse this procedure to install the processor.
84 Chapter 4 Removal and replacement procedures
Page 95

5 Setup Utility (BIOS)

Starting Setup Utility

Setup Utility is a ROM-based information and customization utility that can be used even when your Windows operating system is not working.
The utility reports information about the computer and provides settings for startup, security, and other preferences.
To start Setup Utility:
Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
1.
Startup Menu” message is displayed in the lower-left corner of the screen, press esc.
When the Startup Menu is displayed, press f10.
2.
Starting Setup Utility
85
Page 96

Using Setup Utility

Changing the language of Setup Utility

The following procedure explains how to change the language of Setup Utility. If Setup Utility is not already running, begin at step 1. If Setup Utility is already running, begin at step 2.
Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
1.
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the Startup Menu is displayed, press f10.
2. Use the arrow keys to select System Configuration > Language, and then press enter.
Use the arrow keys to select a language, and then press enter.
3.
When a confirmation prompt with your language selected is displayed, press enter.
4.
5. To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
Your change goes into effect immediately.

Navigating and selecting in Setup Utility

Because Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection are by keystroke.
To choose a menu or a menu item, use the arrow keys.
To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the
arrow keys or f5 or f6.
To select an item, press enter.
To close a text box or return to the menu display, press esc.
To display additional navigation and selection information while Setup Utility is open, press f1.
86 Chapter 5 Setup Utility (BIOS)
Page 97

Displaying system information

The following procedure explains how to display system information in Setup Utility. If Setup Utility is not open, begin at step 1. If Setup Utility is open, begin at step 2.
Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
1.
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the Startup Menu is displayed, press f10.
2. Select the Main menu. System information such as the system time and date, and identification
information about the computer is displayed.
3. To exit Setup Utility without changing any settings, use the arrow keys to select Exit > Exit
Discarding Changes, and then press enter.

Restoring default settings in Setup Utility

The following procedure explains how to restore Setup Utility default settings. If Setup Utility is not already running, begin at step 1. If Setup Utility is already running, begin at step 2.
Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
1.
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the Startup Menu is displayed, press f10.
2. Use the arrow keys to select Exit > Load Setup Defaults, and then press enter.
When the Setup Confirmation is displayed, press enter.
3.
4. To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
Setup Utility default settings go into effect when the computer restarts.
NOTE: Your password, security, and language settings are not changed when you restore the factory
default settings.
Using Setup Utility
87
Page 98

Exiting Setup Utility

You can exit Setup Utility with or without saving changes.
To exit Setup Utility and save your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Saving Changes, and then press enter.
To exit Setup Utility without saving your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Discarding Changes, and then press enter.
After either choice, the computer restarts in Windows.

Setup Utility menus

The menu tables in this section provide an overview of Setup Utility options.
NOTE: Some of the Setup Utility menu items listed in this chapter may not be supported by your
computer.

Main menu

Select To do this
System information

Security menu

Select To do this
Administrator password Enter, change, or delete an administrator password.
Power-On Password Enter, change, or delete a power-on password.
View and change the system time and date.
View identification information about the computer.
View specification information about the processor, memory size,
system BIOS, and keyboard controller version (select models only).
88 Chapter 5 Setup Utility (BIOS)
Page 99

System Configuration menu

Select To do this
Language Support Change the language of Setup Utility.
Button Sound (select models only) Enable/disable the capacitive button tapping sound.
Virtualization Technology (select models only) Enable/disable the processor Virtualization Technology.
Processor C6 State (select models only) Enable/disable the processor C6 sleep state.
LAN Power Saving (select models only) Enable/disable LAN Power Saving. When enabled, saves power when
the computer is in DC mode.
Card Reader/1394 Power Saving (select models only)
Fan Always On Enabled/disable Fan Always On. When enabled, the computer fan will
Action Keys Mode Enable/disable Action Keys Mode.
Boot Options Set the following boot options:
Enable/disable Card Reader/1394 Power Saving.
always be on.
POST hotkey delay (sec.)Set the delay for the f1, f2, f9, f10, f11,
and f12 functions of Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).
CD-ROM BootEnable/disable boot from CD-ROM.
Floppy BootEnable/disable boot from diskette.
Internal Network Adapter BootEnable/disable boot from the
internal network adapter.
Boot OrderSet the boot order for:
Notebook Hard Drive
Internal CD/DVD ROM Drive
USB Diskette on Key/USB Hard Disk
USB CD/DVD ROM Drive
USB Floppy
Network Adapter
Setup Utility menus
89
Page 100

Diagnostics menu

Select To do this
Hard Disk Self Test Run a comprehensive self-test on the hard drive.
Secondary Hard Disk Self Test (select models only) Run a comprehensive self-test on a secondary hard drive.
Memory Test Run a diagnostic test on the system memory.
NOTE: On models with two hard drives, this menu option is called the
Primary Hard Disk Self Test.
90 Chapter 5 Setup Utility (BIOS)
Loading...