The only warranties for HP products and services are set forth in the express statements
accompanying such products and services. Nothing herein should be construed as
constituting an additional warranty. HP shall not be liable for technical or editorial errors or
omissions contained herein.
HP assumes no responsibility for the use or reliability of its software on equipment that is not
furnished by HP.
This document contains proprietary information that is protected by copyright. No part of this
document may be photocopied, reproduced, or translated to another language without the
prior written consent of HP.
Hewlett-Packard Company
P.O. Box 4010
Cupertino, CA 95015-4010
USA
of certain U.S. patents and other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright-protection technology must be
authorized by Macrovision Corporation and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering
or disassembly is prohibited. Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216,
4,819,098, and 4,907,093 licensed for limited viewing uses only.
Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.
Apple, iTunes, FireWire, the FireWire symbol, and iPod are trademarks of Apple Computer,
Inc., registered in the U.S. and other countries.
HP supports lawful use of technology and does not endorse or encourage the use of our
products for purposes other than those permitted by copyright law.
The information in this document is subject to change without notice.
Table of Contents
Setting Up Your PC ......................................................................... 1
Putting Your PC Together............................................................................... 1
Connecting to the PC ...............................................................................2
Turning On Your PC for the First Time .............................................................3
Setting Up and Connecting to Your Internet Account ......................................... 4
Transferring your old PC information and files to your new PC ......................5
Using Desktop Icons...................................................................................... 6
Using Compaq Organize software ............................................................6
Using the Keyboard ....................................................................... 7
Customizing the keyboard buttons ............................................................. 9
Setting Up Sound ......................................................................... 11
Using Speakers .......................................................................................... 11
Setting up 3-connector sound ....................................................................... 12
Configuring multi-channel audio output for the DVD player .........................13
Setting up 6-connector sound ....................................................................... 14
Configuring the Sound Effect Manager (6-connector) ................................. 15
WARNING: Please read “Safety Information” in the Warranty and Support Guide before installing and connecting your PC to
the electrical power system.
WARNING: The power supply is preset for the country/region in
which you purchased your PC. If you move, please check the voltage
requirements before plugging your PC into an AC power outlet.
Putting Your PC Together
Follow the steps on the quick setup poster to set up your PC.
Look in the PC box for printed details or updates regarding your model PC.
After assembling your PC, but before you begin using it, arrange the PC and your
work area to maintain your comfort and productivity. Refer to the Safety & Comfort
Guide for important ergonomic information.
WARNING: To reduce the risk of serious injury, read the Safety &
Comfort Guide. It describes proper workstation setup, posture, and
health and work habits for computer users. It also provides
important electrical and mechanical safety information.
To view the Safety & Comfort Guide:
• Click Start, choose All Programs, choose Documentation, and then click
Safety & Comfort Guide.
Or
• Type
http://www.hp.com/ergo/
into your Web browser address box, and then press Enter on the keyboard.
Setting Up Your PC1
Connecting to the PC
Your PC features and
location, availability,
and number of
connectors may vary.
Connect your main hardware devices like the monitor, keyboard, and mouse to the
back of the PC. Other peripheral devices like a printer, scanner, camera, or other
equipment also plug into connectors on the back of your computer. Some PC models
also have connectors on the front of the PC. The table does not show all connectors.
ConnectorConnector
symbol
Description
Mouse (PS/2 connector)
Keyboard (PS/2 connector)
Universal Serial Bus (USB) for mouse,
keyboard, digital cameras, or other devices
with USB connectors
2Getting Started Guide
Printer (parallel)
Monitor
Serial port for some digital cameras or
other serial devices
Serial
ConnectorConnector
symbol
OUT
IN
Description
Audio Line Out (powered speakers)
Audio Line In
Headphones
Microphone
®
FireWire
(IEEE 1394) for video cameras
or other devices with very fast transfer rates
Turning On Your PC for the First Time
After you have completed the steps on the quick setup poster, you are ready to turn
on your PC.
1 Press the Power button on the monitor.
2 Press the On button on the front of the PC.
3 Turn on the speakers, if they are present.
4 Click an option to select your language (if applicable for your model). Click
OK, and then confirm your selection by clicking Yes. Wait until the PC makes
preparations. (It may take up to 30 minutes for this one-time language setup on
the PC.)
5 Set up Microsoft
®
Windows® by following the onscreen instructions.
Setting Up Your PC3
6 Double-click the large Internet Access icon, if it is present on your desktop.
Wait until the PC displays the Easy Internet Sign-up window, and then follow the
onscreen instructions.
7 Register your PC.
Setting Up and Connecting to Your
Internet Account
Before you can connect to the Internet, you must sign up with an Internet service
provider (ISP). HP has made arrangements with leading ISPs to help you sign up for
Internet service using Easy Internet Sign-up (available on select models only).
NOTE: You may use any other ISP of your choice, or transfer your existing ISP
account to this PC.
Use Easy Internet Sign-up to sign up for a new or transfer an existing ISP account
(select ISPs only). The software programs for available ISPs are part of your PC. If
you decide to subscribe to high-speed broadband, cable or digital subscriber line
(DSL), contact your ISP for any specific software and hardware you may need.
1 Make sure the modem or other Internet access cable is connected.
NOTE: Easy Internet Sign-up finds and obtains updated information about ISP
services by temporarily connecting to the Internet. The PC uses either the PC
modem connected to an active telephone service line or an active broadband
(cable or DSL) connection.
2 Choose an ISP using Easy Internet Sign-up. To open Easy Internet Sign-up:
a Double-click the Easy Internet Sign-up icon on the desktop.
Or
Click Start on the taskbar, choose All Programs, choose
Online Services, and then click Easy Internet Sign-up.
b Follow the onscreen instructions.
NOTE: The folder called Online Services includes icons for accessing various
online services, but they may not be present in all countries/regions.
3 Connect to your ISP and the Internet (after you established your ISP account on
this PC).
Use one of these methods:
• Double-click the ISP-provided icon on the desktop.
Or
• Press the Connect (or Internet) button on the keyboard (select
models only).
Or
4Getting Started Guide
• If your PC is always connected to your ISP, open your browser program,
such as Internet Explorer: Click Start, choose AllPrograms, choose
Online Services, and click Internet Explorer.
NOTE: If you are using MSN, AOL, or others and have questions, contact the ISP
directly.
Installing Software and Hardware Devices
After you turn on the PC the first time, you can install any software programs that
came on CDs or DVDs included in the PC box (select models only).
You may wish to install additional software programs or hardware devices on your
PC. Before installation, make a restore point using the Microsoft System Restore
program, and then restart the PC after installation. By using System Restore, you
insure you have a point to return to before an issue occurred. For information about
System Restore, refer to the Microsoft Web site at:
http://www.microsoft.com/worldwide/
Choose software that is compatible with your PC — check the operating system,
memory, and other requirements listed for the new software for compatibility with
your PC.
NOTE: Only use original licensed software. Installing copied software may be
illegal or may infect your PC with a virus.
Install the new software according to the directions provided by the software
manufacturer. Check the manufacturer’s documentation or customer service
information for help if you need it.
For antivirus software, uninstall the existing software program before reinstalling it
or installing a new antivirus program.
Transferring your old PC information and files to
your new PC
See the built-in Microsoft Windows Help and Support Center; search for transfer
wizard, and select the overview article, “Files and Settings Transfer Wizard
overview.” This information describes a Microsoft solution for moving your files
onto your new PC.
Setting Up Your PC5
Using Desktop Icons
The desktop has shortcut icons that make it easy to find the things you need.
IconOpensUse it to
Help and Support (select
models only)
Easy Internet Sign-upSet up a new or an existing
Compaq Organize (select
models only)
View onscreen Help information
about your PC.
Internet account.
Organize your PC shortcuts and
your favorite Internet destination
links.
Using Compaq Organize software
Compaq Organize software (select models only) is a desktop tool you use to
organize both your PC shortcuts and your favorite Internet destination links. You use
it to organize the important things you do on the PC and the Internet, and to
arrange them the way you want. Compaq Organize makes all your information
available with just a few mouse clicks.
Compaq Organize looks like a window with multiple category frames. Each
category has links to Internet destinations or shortcuts to software programs or files
on your PC. Use the player area for viewing pictures, for listening to your MP3
music files stored on your computer, or for watching video clips. For searching,
there is a search bar at the top of Compaq Organize where you can select the
search engine you want to use.
6Getting Started Guide
To open Compaq Organize:
Double-click the desktop icon.
Or
1 Click Start on the taskbar.
2 Choose All Programs.
3 Click Compaq Organize.
Using the Keyboard
Your keyboard has an arrangement of standard keys, indicator lights, and special
buttons (select models only).
Identifying Special Keyboard Buttons
There are special buttons (select models only) at the top of the keyboard. (Some
models have some of these special buttons on the left side of the main keys.) These
buttons operate a CD or DVD player, connect you to the Internet, or provide quick
access to specific functions.
NOTE: The number, location, and labeling of buttons vary by keyboard model.
IconFeatureDescription
StandbyPuts PC into power-saving mode (screen is
blank but PC is still on). To make screen
reappear, press the Esc key, or press
Standby again. May take 10–30 seconds
before screen reappears.
Compaq or
or
or
or
UserSwitches between the PC users.
Compaq
My Presario
HelpOpens the Help and Support Center.
Pictures
(Photos)
MusicStarts iTunes or Windows Media Player.
VideoOpens video software program. Can be
Links to Compaq Web site.
Opens an imaging software program. Can
be reconfigured.
Can be reconfigured.
reconfigured.
Using the Keyboard7
IconFeatureDescription
Shopping
, or
Sports
or
Finance
or
Connect
, or
, or
or
or
Internet
SearchGoes to popular Web sites. Can be
reconfigured to open a site or software
program.
Chat
E-Mail
Entertainment
Offers
CalculatorOpens the calculator. Can be reconfigured.
A
B
C
D
E
F
Media
controls (CD/
DVD/MP3)
Operates a disc player.
A Open and close disc tray
B Record
C Play or pause
D Stop
ESkip to the previous track
FSkip to the next track
8Getting Started Guide
IconFeatureDescription
Volume
or
, or
NOTE: The number, location, and labeling of buttons vary by keyboard model.
control
(Volume knob
or Volume Up
and Volume
Down
buttons)
MuteTurns speaker sound on and off.
Volume knob: Increases speaker volume
when turned clockwise and decreases
volume when turned counterclockwise. It
can be turned indefinitely, even after
maximum sound has been reached.
Volume Up and Down buttons: Press the
Volume Up button to increase volume
and the Volume Down button to
decrease volume.
Customizing the keyboard buttons
You can customize some of the special buttons on the keyboard (select models only)
to open different programs or files or to connect to favorite Web sites:
1 Click Start on the taskbar.
2 Choose Control Panel.
3 Click Printers and Other Hardware, if it is present.
4 Double-click Keyboard.
5 On the Buttons tab, double-click the button you want to change.
6 For the Button configuration, click the Down arrow to the right of the list and
choose the button capability, such as Simple web page with label.
7 Enter a display label and the address information. For a Web page, enter
the URL.
8 Click OK.
9 On the Buttons tab, click Apply.
10 Repeat steps 5 through 9 for each button you want to customize.
11 Click OK to finish.
NOTE: Clicking the Restore Defaults button on the Button tab restores all of the
Internet buttons to the factory settings.
Using the Keyboard9
10Getting Started Guide
Setting Up Sound
Using Speakers
Speakers are included with the monitor (select models only) or are sold separately.
Your PC supports only an active (powered) speaker system; the speaker system must
have its own power cord.
NOTE: A stereo speaker set is a left-right, two-channel speaker system. A multi-
channel audio speaker system is a system with more than two channels, and it may
include a subwoofer. For example, 7.1 channels, referred to as an eight-speaker
mode, uses two front speakers (left-right), two side speakers (left-right), two rear
speakers (left-right), a center speaker, and a subwoofer.
The PC supports a variety of sound options and speaker configurations. You may set
NOTE: If your PC
includes a sound
card (select models
only), refer to the
documentation that came
with the sound card.
up your PC for two stereo speakers or for multi-channel audio speaker systems.
Connect your speaker system to the PC, and then configure the audio software for
sound output. For details on connecting stereo speakers to the PC, see the quick
setup poster. Location, availability, and number of connectors may vary.
• If your PC model includes three sound connectors (select models only) on the
back of the PC, see “Setting up 3-connector sound” on page 12.
IN
OUT
• If your PC model includes six sound connectors (select models only) on the back
of the PC, see “Setting up 6-connector sound” on page 14.
Setting Up Sound11
Setting up 3-connector sound
PC models that include three sound connectors (select models only) on the back of
the PC support up to six channels of sound (5.1 speaker output) and use the
Multi-channel Sound Manager to configure the software settings.
Connecting the speaker system to the PC (3-connector)
The 3-connector audio speaker system uses the Audio In, Audio Out, and Mic
connectors on the back or front of the PC. Refer to the quick setup poster for the
location of the connectors.
1 With the speaker system off, assemble the speakers and, if used, the subwoofer.
Refer to the speaker documentation.
2 Turn off the PC.
3 Connect the three audio cable plugs from the speaker system to the connectors
on the back of the PC. (See the following table.)
Connect speaker plugs for:
4/4.1
2 Speaker
Mode
Front
speakers
Not used for
speakers
Not used for
speakers
4 Turn on the PC.
5 Turn on the speaker system.
6 Configure the audio output for this 3-connector multi-channel speaker system by
performing the following procedure.
Speaker
Mode
Front
speakers
Rear speakersRear speakersAudio In
Not used for
speakers
6/5.1
Speaker
Mode
Front
speakers
Center/
subwoofer
speakers
To PC
connector
Audio Out
(lime green)
(blue)
Mic-1 (pink)
Connector
icon
OUT
IN
Configuring the Multi-Channel Sound Manager
(3-connector)
1 Click Start on the taskbar.
2 Choose All Programs.
12Getting Started Guide
3 Click Multi-channel Sound Manager. The Multi-channel Audio
Configuration window opens.
NOTE: If you do not see the Speaker Configuration tab, your PC does not have
the multi-channel capability. However, it still has two-channel (stereo) output.
4 Click the Speaker Configuration tab.
5 Select the option describing the number of speakers in your system, for
example, 6/5.1 speaker mode. You can click the Speaker Test tab and
then click a speaker icon to test it.
6 Click OK.
To use a microphone for recording, see “Using the microphone with the MultiChannel Sound Manager (3-connector)” on page 13.
To hear DVD movies recorded with multi-channel audio from all speakers, change
the audio properties for WinDVD to match your speaker configuration (if your
InterVideo WinDVD program supports more than two channels). Refer to
“Configuring multi-channel audio output for the DVD player” on page 13.
Using the microphone with the Multi-Channel Sound
Manager (3-connector)
The 3-connector multi-channel speaker system (select models only) connects to the
PC using the Microphone, Audio (Line) In, and Audio (Line) Out connectors on the
back of the PC. Your PC may have a second microphone connector on the front of
the PC. If present, this microphone connector is ready to use and does not affect the
use of the multi-channel audio speaker system.
To use the microphone connector on the back of the PC with a 3-connector multichannel audio speaker system, you must disconnect the cables for the multi-channel
speakers and change the audio configuration to a two-channel audio system. Refer
to “Configuring the Multi-Channel Sound Manager (3-connector)” on page 12 to set
the audio configuration.
Configuring multi-channel audio output for the
DVD player
The InterVideo WinDVD program (select models only) is set up for two-speaker
(stereo) output. To hear all speakers from DVD movies recorded with multi-channel
audio, change the audio properties for WinDVD to match your speaker
configuration (if your InterVideo WinDVD program supports more than two
channels):
1 Insert a DVD, or start InterVideo WinDVD. (Click Start, choose All
Programs, choose InterVideo WinDVD, select InterVideo WinDVD
Player, and then click InterVideo WinDVD.) The WinDVD video window
opens.
2 Right-click anywhere in the WinDVD video window, and then click Setup. The
Setup window opens.
Setting Up Sound13
3 Click the Audio tab.
A
4 Click the option for the number of speakers to match your multi-channel speaker
system.
NOTE: When using the digital out connector for sound (6-connector, select
models only), select Digital (S/PDIF) out to External Processor.
5 Click Apply.
NOTE: To test the speakers (multi-channel speakers only), click the Test button.
The WinDVD control panel shows the speaker number being used. Click Stop.
6 Click OK.
NOTE: If you want to play a stereo DVD, change the audio properties of WinDVD to
match the recorded DVD audio output.
Setting up 6-connector sound
PC models that include six sound connectors (select models only) on the back of the
PC, support up to eight channels of sound (7.1 speaker output) and use the Sound
Effect Manager to configure the software settings.
Identifying the audio connectors (6-connector)
The PC supports a maximum of eight speakers in a multi-channel speaker system by
using four of the six audio connectors on the back of the PC.
This PC also has digital audio out and digital audio in connectors for digital sound
devices such as a DVD recorder or a digital stereo receiver/amplifier.
The four connectors (A, B, C, and E) for the 6-connector multi-channel speaker
Side speaker port
(side)
B Rear speaker port
(rear)
C Center speaker/
subwoofer port
(c/sub)
D Microphone (mic)
E Audio line out (out) for
front speakers
F Audio line in (in)
system are on the back of the PC.
A
D
BC
EF
14Getting Started Guide
The previous figure shows the six audio connectors arranged on the back of the PC:
the four connectors (A, B, C, and E) used for eight-channel audio and the
connectors for the microphone (D, mic) and the audio line in (F, in).
Connecting the speaker system to the PC (6-connector)
1 With the speaker system off, assemble the speakers and, if used, the subwoofer.
Refer to the speaker documentation.
2 Turn off the PC.
3 Connect the audio cable plugs from the speaker system subwoofer to the
connectors on the back of the PC. (See the following table.)
Connect speaker cable (plug) for:To PC port (label, name,
color):
Front speakers (or two stereo speakers)Audio line out (E, out, lime green)
Side speakersSide speaker (A, side, gray)
Rear speakersRear speaker (B, rear, black)
Center speaker/subwooferCenter speaker/subwoofer
(C, c/sub, gold)
4 Turn on the PC.
5 Turn on the speaker system.
6 Configure the audio output for this 6-connector multi-channel speaker system by
performing the following procedure.
Configuring the Sound Effect Manager
(6-connector)
1 Click Start on the taskbar.
2 Choose Control Panel.
3 If it is present, click Sounds, Speech, and Audio Devices.
4 Click Sound Effect Manager. The window opens.
5 Click the Speaker Configuration button.
6 Select the option describing the number of speakers in your system, for
example, 7.1 speakers.
A connector with no descriptive text in the Connection Guide indicates that the
connector is not used for the selected speaker configuration.
NOTE: You can click the Speaker Test button to test the speakers.
7 Click OK.
Setting Up Sound15
To hear DVD movies recorded with multi-channel audio from all speakers, change
the audio properties for WinDVD to match your speaker configuration (if your
InterVideo WinDVD program supports more than two channels). Refer to
“Configuring multi-channel audio output for the DVD player” on page 13.
To use a microphone or set up the PC for recording, see “Configuring sound for
recording with the Sound Effect Manager (6-connector)” on page 16.
To use the other features of the Sound Effect Manager, see “Using the Sound Effect
Manager (6-connector)” on page 17.
Configuring sound for recording with the
Sound Effect Manager (6-connector)
The microphone connector on the front of the 6-connector audio PC is ready to use
for recording sound. If you want to use another connector for recording, such as the
digital audio in connector, use these steps to select it.
NOTE: The pink and green connectors on the front of a PC with 6-connector
sound can be retasked to perform other audio functions; refer to “Using the Audio
Wizard in the Sound Effect Manager (6-connector)” on page 18.
1 Click Start on the taskbar.
2 Choose Control Panel.
3 If it is present, click Sounds, Speech, and Audio Devices.
4 Click Sounds and Audio Devices.
5 Click the Audio tab.
6 In Sound recording select the default device from the drop-down list. Choose:
• RealTek HD Front Pink Jack to use the microphone connector on the
front of the PC.
• RealTek HD Digital Input to use the digital audio in connector on the
back of the PC.
• RealTek HD Front Green Jack to use the green connector on the front
of the PC.
• Back Line in/Mic, Front Line in to use the audio line in (in) or the
microphone (mic) connectors on the back of the PC, or to use the audio line
in connector on the front of the PC.
16Getting Started Guide
NOTE: For this selection, the audio line in connector is ready to use. To use
the back mic connector, follow the steps in “Selecting the Back Line in/Mic,
Front Line in connectors for recording (6-connector)” that follows this
procedure.
7 Click Apply, and then click OK to close the window.
Selecting the Back Line in/Mic, Front Line in connectors for
recording (6-connector)
Perform these steps when you select Back Line in/Mic, Front Line in for the
sound recording in step 6 of the previous procedure.
NOTE: If you want to record from the mic connector on the back of the PC, you must
perform these steps.
1 Click Start on the taskbar.
2 Choose Control Panel.
3 If it is present, click Sounds, Speech, and Audio Devices.
4 Click Sounds and Audio Devices.
5 On the Volume tab, in the Device volume area click the Advanced button. The
Master Volume window opens.
6 Click Options and choose Properties.
7 In the Mixer device area, select Back Line in/Mic, Front Line in from the
drop-down list. Click OK.
8 The recording control window opens and shows Line In 1 or 2 selected. The line
in connector you plug into is used. However, to use the mic connector on the
back of the PC, click the Select check box under Microphone so a check mark
appears in the box.
Using the Sound Effect Manager (6-connector)
The Sound Effect Manager has four buttons that display its control screens.
To open the Sound Effect Manager:
1 Click Start on the taskbar.
2 Choose Control Panel.
3 If it is present, click Sounds, Speech, and Audio Devices.
4 Click Sound Effect Manager. The window opens.
5 Click a button near the top of the window to see that control screen.
The Sound Effect Manager control screens:
• Sound Effect — selects the Environment and the Equalizer settings. You can
select an Environment, such as Under Water or Auditorium. To use the
Equalizer, click the Power button in the center of the circular equalizer control to
turn on the Equalizer. You can click a preset button, such as Pop or Live, or
manually adjust the settings and then save them for easy selection later.
• Speaker Configuration — selects the number of speakers, shows the
Connection Guide, and has the Speaker Test button to test the speakers. A
connector with no descriptive text in the Connector Guide indicates that the
connector is not used for the selected speaker configuration.
Setting Up Sound17
• Digital Audio — selects the digital audio output and digital audio frequency
for the digital audio connectors on the PC.
•Audio Wizard — opens a window that shows the connector panel on the
front of the PC. To close the window without enabling the wizard, click OK.
To enable the Audio Wizard:
Make sure the Enable auto detection check box is selected to enable the
wizard. Click OK to close the window.
Using the Audio Wizard in the Sound Effect Manager
(6-connector)
When you click the Audio Wizard button, a window opens that shows the three
audio connectors on the front of the PC.
NOTE: The connectors on the front of your PC may be of a different type or may be
in a different arrangement; look for the connector icon and color. Location,
availability, and number of connectors may vary.
/
ABC
C
A
B
ConnectorNameIconColor
AAudio Line InLight blue
IN
BMicrophonePink
CHeadphones
Or
Audio Line Out
Or
OUT
Lime
green
Retasking using the Audio Wizard (6-connector)
With the Audio Wizard enabled, both the microphone connector (B) and the
headphones connector (C) on the front of the PC can be retasked to perform a
different audio function. These two connectors are universal audio jacks. When you
plug in a cable, the Wizard asks you to select the function for the cable from a list,
and then it sets the universal audio jack to perform as the selected function. The
functions are:
18Getting Started Guide
• Stereo speaker (out)
• Microphone (in)
• Headphone (out)
• Audio line in
Using the Memory Card Reader
Digital cameras and other digital imaging devices use memory cards, or media,
to store digital picture files. The optional memory card reader (select models only)
can read and write to a variety of types of memory cards and the IBM Microdrive
disk drive.
The card reader is accessible directly on the front of the PC. It has four horizontal
card slots, which accept the memory cards and the Microdrive disk drive.
Card4-slot reader
CompactFlash Type I mediaLower-left slot
CompactFlash Type II mediaLower-left slot
IBM Microdrive disk driveLower-left slot
Secure Digital (SD) Memory CardUpper-right slot
MultiMediaCard (MMC)Upper-right slot
Memory Stick (MS) Memory CardLower-right slot
Memory Stick (MS-Pro) Memory CardLower-right slot
SmartMedia (SM) Memory CardUpper-left slot
xD mediaUpper-left slot
You can place media in one or more of the card slots and use each media
independently. Place only one piece of media in a slot at one time.
Each card slot has its own drive letter and icon. When you insert media, the display
label may change to the title of the media, if the title is present.
Using the Memory Card Reader19
Working with the Safely Remove
Hardware utility
CAUTION: Do not click Stop in the Safely Remove Hardware window
with the USB Mass Storage Device selected. Doing so removes the
operating system recognition of the memory card reader from your
PC; you must restart the PC to see your memory card reader again.
If you open the Safely Remove Hardware window by mistake, click Close.
Using the memory card reader
NOTE:
CompactFlash and Microdrive are keyed and cannot be inserted incorrectly.
Insert the receptacle edge (holes) of this media into the slot.
1 Insert the media into the card slot until it stops. The activity light (A) on the
memory card reader lights, and the PC automatically detects the media.
2 The PC opens a window so you can use the media contents. You can copy files
from or to the media.
3 When you are finished, right-click the drive icon, select Eject, check that the
activity light is on but not blinking, and then remove the media. A steady
activity light indicates that the PC is not reading or writing the media.
WARNING: Do not try to remove media when the activity light is
blinking; doing so may cause loss of data.
20Getting Started Guide
Loading...
+ 60 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.