U.S. and/or other countries.
All other product names mentioned herein may be trademarks of their respective
companies.
This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
HP shall not be liable for technical or editorial errors or omissions contained herein.
The information is provided “as is” without warranty of any kind, and is subject to
change without notice. The warranties for HP products are set forth in the express
limited warranty statements accompanying such products. Nothing herein should be
construed as constituting an additional warranty.
Compaq Notebook Series Reference Guide
First Edition (December 2002)
Reference Number: 2100/2500/N1050v
Part Number: 311069-001
iiReference Guide
Important Safety Information
CAUTION
To reduce the risk of fire, use only No. 26 AWG or larger telecommunications
line cord to connect a modem to the telephone wall jack. In Australia, the
notebook must be connected to the Telecommunication Network through a
line cord that meets the requirements of ACA Technical Standard TS008.
When using your notebook with a telephone connection, always follow basic safety
precautions to reduce the risk of fire, electric shock, and injury to persons.
• Do not use this product with a telephone connection near water (for example,
near a bathtub, sink, swimming pool, or in a wet basement).
• Avoid using a telephone connection (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from lightning.
• Do not use a telephone connection to report a gas leak in the vicinity of the leak.
• Use only the power cord and batteries indicated in this manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for possible special
disposal instructions.
• Disconnect the modem cable before opening the notebook case or touching an
uninsulated modem cable, jack, or internal component.
• Do not plug a modem cable or telephone cable into the network (LAN)
receptacle.
Reference Guideiii
Software Product License Agreement
Your HP product contains software programs. CAREFULLY READ THIS
LICENSE AGREEMENT BEFORE PROCEEDING TO OPERATE THIS
EQUIPMENT. RIGHTS IN THE SOFTWARE ARE OFFERED ONLY ON THE
CONDITION THAT THE CUSTOMER AGREES TO ALL TERMS AND
CONDITIONS OF THE LICENSE AGREEMENT. PROCEEDING TO OPERATE
THE EQUIPMENT INDICATES YOUR ACCEPTANCE OF THESE TERMS
AND CONDITIONS. IF YOU DO NOT AGREE WITH THE TERMS OF THE
LICENSE AGREEMENT, YOU MUST NOW EITHER REMOVE THE
SOFTWARE FROM YOUR HARD DISK DRIVE AND DESTROY THE
MASTER DISKETTES, OR RETURN THE COMPLETE HP PRODUCT AND
SOFTWARE FOR A FULL REFUND. PROCEEDING WITH CONFIGURATION
SIGNIFIES YOUR ACCEPTANCE OF THE LICENSE TERMS.
UNLESS OTHERWISE STATED BELOW, THIS HP SOFTWARE LICENSE
AGREEMENT SHALL GOVERN THE USE OF ALL SOFTWARE THAT IS
PROVIDED TO YOU AS PART OF THE HP PRODUCT AND SHALL
SUPERSEDE ANY OTHER SOFTWARE WARRANTY STATEMENT THAT
MAY BE INCLUDED IN THIS HP PRODUCT OR MAY BE FOUND ONLINE.
Operating system and software applications by Microsoft are licensed to you under
the Microsoft License Agreement contained in the Microsoft documentation or
displayed on your screen when Microsoft Software Products are launched.
For a PC supplied with a Microsoft operating system: When you start the PC and
accept the Microsoft End-user License Agreement (“EULA”), your license rights are
valid only if a Certificate of Authenticity (“COA”) label corresponding to your
Microsoft operating system is provided with your PC. The COA label can usually be
found on the bottom of the notebook. If the COA label does not correspond to your
Microsoft operating system or is missing, contact your HP reseller for details.
Other non-HP Software and Operating Systems are covered by the appropriate
vendor license. The following License Terms govern the use of the HP software:
USE. Customer may use the software on any one HP product. Customer may not
network the software or otherwise use it on more than one HP product. Customer
may not reverse assemble or decompile the software unless authorized by law.
COPIES AND ADAPTATIONS. Customer may make copies or adaptations of the
software (a) for archival purposes or (b) when copying or adaptation is an essential
step in the use of the software with an HP product so long as the copies and
adaptations are used in no other manner.
ivReference Guide
OWNERSHIP. Customer agrees that he/she does not have any title or ownership of
the software, other than ownership of the physical media. Customer acknowledges
and agrees that the software is copyrighted and protected under the copyright laws.
Customer acknowledges and agrees that the software may have been developed by a
third party software supplier named in the copyright notices included with the
software, who shall be authorized to hold the Customer responsible for any copyright
infringement or violation of this Agreement.
PRODUCT RECOVERY CD-ROM or DVD. If your HP product was shipped with a
product recovery CD-ROM or DVD: (i) The product recovery CD-ROM or DVD
and/or support utility software may only be used for restoring the hard disk of the HP
product with which the product recovery CD-ROM or DVD was originally provided.
(ii) The use of any operating system software by Microsoft contained in any such
product recovery CD-ROM or DVD shall be governed by the Microsoft License
Agreement.
TRANSFER OF RIGHTS IN SOFTWARE. Customer may transfer rights in the
software to a third party only as part of the transfer of all rights and only if Customer
obtains the prior agreement of the third party to be bound by the terms of this
License Agreement. Upon such a transfer, Customer agrees that his/her rights in the
software are terminated and that he/she will either destroy his/her copies and
adaptations or deliver them to the third party.
SUBLICENSING AND DISTRIBUTION. Customer may not lease, sublicense the
or distribute copies or adaptations of the software to the public in physical media or
by telecommunication without the prior written consent of Hewlett-Packard.
TERMINATION. Hewlett-Packard may terminate this software license for failure to
comply with any of these terms provided Hewlett-Packard has requested Customer
to cure the failure and Customer has failed to do so within thirty (30) days of such
notice.
UPDATES AND UPGRADES. Customer agrees that the software does not include
updates and upgrades which may be available from Hewlett-Packard under a
separate support agreement.
EXPORT CLAUSE. Customer agrees not to export or re-export the software or any
copy or adaptation in violation of the U.S. Export Administration regulations or
other applicable regulation.
Reference Guidev
U.S. GOVERNMENT RESTRICTED RIGHTS. Use, duplication, or disclosure is
subject to HP standard commercial license terms and for non-DOD Departments and
Agencies of the U.S. Government, the restrictions set forth in FAR 52.227-19(c)(1-2)
(June 1987) Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304
U.S.A. Copyright (c) 2000 Hewlett-Packard Company. All Rights Reserved.
Customer further agrees that Software is delivered and licensed as “Commercial
notebook software” as defined in DFARS 252-227-7014 (June 1995) or as a
“commercial item” as defined in FAR 2.101(a), or as “Restricted notebook software”
as defined in FAR 52.227-19 (or any equivalent agency regulation or contract
clause), whichever is applicable. The Customer agrees that it has only those rights
provided for such Software by the applicable FAR or DFARS clause or the HP
standard software agreement for the product involved.
SUPPORT POLICY FOR MICROSOFT OPERATING SYSTEMS SERVICE
PACK. HP will provide end user support for HP PCs that use Microsoft Operating
Systems, including its latest service packs. This support will be available 30 days
after the service pack being released by Microsoft.
viReference Guide
Contents
Getting Started with Your Notebook...........................................................................1
Identifying Parts of the Notebook ..........................................................................2
Series 2100 and N1050v...................................................................................2
Series 2500........................................................................................................5
Status Lights .....................................................................................................8
Setting Up Your Notebook...................................................................................10
Step 1: Insert the battery.................................................................................10
Step 2: Connect AC power .............................................................................11
Step 3: Connect a phone line ..........................................................................12
Step 4: Turn on the notebook .........................................................................13
Step 5: Set up Windows..................................................................................13
Index ........................................................................................................................110
Reference Guideix
Getting Started with Your Notebook
Reference Guide1
Getting Started with Your Notebook
Identifying Parts of the Notebook
Identifying Parts of the Notebook
Series 2100 and N1050v
NOTE
Components included with the notebook may vary by geographical region and the
features you selected. The following illustrations identify the standard external
components included with most notebook models.
1Notebook open/close latch.
2One-Touch buttons.
3Keyboard status lights.
4Power button. Turns the notebook on and off.
5TouchPad, scroll pad, Click buttons, and
on-off button.
6Main status lights (left to right): power mode,
hard disk activity, and battery.
2Reference Guide
7Hard disk drive.
8Infrared port (select models only).
9Wireless on-off button and indicator light
(select models only).
10 Battery.
11 CD-ROM, DVD, or other drive.
12 PS/2 port.
Getting Started with Your Notebook
Identifying Parts of the Notebook
13 AC adapter jack.
14 Universal serial bus ports (USB).
15RJ-45 jack. Connects a network cable.
16 S-video out jack.
17 Parallel port (LPT1). Use this port for a parallel
printer or other parallel device.
18 Serial port (COM1). Use this port for a serial
mouse, modem, printer, or other serial device.
19 External monitor port.
20 Kensington lock slot (security connector).
21 RJ-11 jack. Connects the modem cable.
22 PC Card and CardBus slot and button.
23 IEEE 1394 port (select models only).
24 Audio jacks (left to right): external microphone,
audio out (headphones).
25 Volume control.
26 Audio mute button and audio mute light.
27 Floppy disk drive (select models only).
Reference Guide3
Getting Started with Your Notebook
Identifying Parts of the Notebook
28 Hard disk drive.
29 Battery latch.
30 RAM (memory) cover.
4Reference Guide
31 Reset button.
32 Docking port (select models only).
33 Mini-PCI cover (no user parts inside).
Series 2500
Getting Started with Your Notebook
Identifying Parts of the Notebook
1Notebook open/close latch.
2One-Touch buttons.
3Keyboard status lights.
4Power button. Turns the notebook on and off.
5TouchPad, scroll pad, Click buttons, plus
on-off button.
6Main status lights (left to right): power mode,
hard disk activity, and battery.
7Infrared port (select models only).
8Wireless on-off button and indicator light
(select models only).
9Battery.
10Audio mute button, audio mute light, and
volume control.
11Audio jacks (left to right): audio out
(headphones), external microphone.
12CD-ROM, DVD, or other drive.
13Universal serial bus port (USB).
Reference Guide5
Getting Started with Your Notebook
Identifying Parts of the Notebook
14 AC adapter jack.
15 Two USB ports.
16 RJ-45 network jack. Connects a network
cable.
17 PS/2 port.
18 Parallel port (LPT1). Use this port for a
parallel printer or other parallel device.
6Reference Guide
19 External monitor port.
20 S-video out jack.
21 Kensington lock slot (security connector).
22 RJ-11 jack. Connects a modem cable.
23 IEEE 1394 port (select models only).
24 PC Card and CardBus slot and buttons.
25 Floppy disk drive (select models only).
Getting Started with Your Notebook
Identifying Parts of the Notebook
26 Hard disk drive.
27 Battery latch.
28 Mini-PCI cover (no user parts inside).
The notebook includes a number of status lights that report power and battery status,
drive activity, and keyboard functions such as Caps Lock and Num Lock.
The following diagram shows the main status lights on the front of the notebook.
1Powermode.
• On: the notebook is on (even if the display is off).
• Blinking: the notebook is in Standby.
• Off: the notebook is off or in Hibernation.
2 Hard disk drive activity.
On: notebook is accessing the hard disk drive.
3 Battery status.
• Green: the AC adapter is connected and the battery is fully charged.
• Amber: the AC adapter is connected and the battery is charging.
• Blinking: the AC adapter is connected and the battery is missing or has a
fault.
• Off: the AC adapter is not connected.
8Reference Guide
Getting Started with Your Notebook
Identifying Parts of the Notebook
The keyboard status lights, located above the keyboard, indicate the states of the
keyboard locks.
1 Caps Lock On: Caps Lock is active.
2NumLockOn:NumLockisactive.(TheKeypadLockmustalsobeontouse
the embedded keypad.)
3 KeypadLockOn:The embedded keypad is active (Fn+F8). Num Lock must
also be on for the numeric keys. Otherwise, cursor control is active (as marked
on an external keyboard).
Reference Guide9
Getting Started with Your Notebook
Setting Up Your Notebook
Setting Up Your Notebook
WARNING
WARNING
Improper use of keyboards and other input devices has been associated with
ergonomic injury.
If you are using your notebook as your primary computer, or using it for
extended periods, you should use it with a full-sized keyboard, monitor, and
mouse. Docking accessories offer quick, easy connections to these devices. This
can reduce the risk of ergonomic injury.
For information about setting up a safe and comfortable work environment,
see the Safety & Comfort Guide on this CD.
When you set up your notebook for the first time, you’ll charge the battery, connect
the AC adapter, turn on the notebook, and run the Windows setup program.
Step 1: Insert the battery
Do not mutilate or puncture batteries. Do not dispose of batteries in fire, or
they can burst or explode, releasing hazardous chemicals. Rechargeable
batteries must be recycled or disposed of properly.
Your notebook is shipped with the battery installed. If the battery has been removed,
you should install it:
1. Turn the notebook upside down.
2. Insert the connector end of the battery into the battery compartment and slide it in
until it latches.
10Reference Guide
Step 2: Connect AC power
Getting Started with Your Notebook
Setting Up Your Notebook
CAUTION
Important
Use only the AC adapter included with your notebook (or other approved
adapter that meets the power requirements of the notebook).
Using the wrong AC adapter could damage the notebook or adapter, cause
data loss, and may void your warranty. (See the printed document WorldwideLimited Warranty and Technical Support that came with the notebook.)
1. Plug the AC adapter into the notebook.
2. Connect the power cord to the AC adapter.
3. Plug the power cord into a wall outlet.
The notebook battery then starts charging.
When unplugging the power cord, unplug it from the outlet before unplugging it
from the AC adapter.
While the battery is charging, you can continue with step 3.
Reference Guide11
Getting Started with Your Notebook
Setting Up Your Notebook
Step 3: Connect a phone line
1. Make sure the telephone line is an analog line, sometimes called a data line. (You
must not use a digital line.)
2. Connect the telephone cord (RJ-11) into a telephone jack
3. Plug the other end of the phone cord into the RJ-11 modem jack in the side of the
notebook.
For details about using the modem, see “Using the Modem” in this guide.
12Reference Guide
Getting Started with Your Notebook
Setting Up Your Notebook
Step 4: Turn on the notebook
Press the power button above the left side of the keyboard. The notebook then
boots up, and Windows starts automatically.
Hint
If your notebook does not turn on when operating on battery power, the battery may
be out of power. Plug in the AC adapter and press the power button again. Leave
the AC adapter plugged in for at least an hour or up to 3 hours to charge it fully.
Step 5: Set up Windows
Your notebook has the Microsoft Windows operating system preinstalled on its hard
disk drive. The first time you turn on your notebook, the Windows Setup program
runs automatically so you can customize your setup.
1. Follow the Setup program instructions on the screen. If the program prompts you
to enter the Product ID code, you will find this code on the bottom of the
notebook.
2. Check the modem’s country or region settings. Select Start > Control Panel >
Printers and Other Hardware > Phone and Modem Options > then choose your
country/region..
Reference Guide13
Basic Operation
Reference Guide15
Basic Operation
Operating Your Notebook
Operating Your Notebook
You can start and stop your notebook using the power button. However, at certain
times you may want to use other methods to start or stop the notebook, depending on
power considerations, types of active connections, and startup time.
Default power settings
Power modeTo enter this modeFunction
ON—Power status
light will turn on.
OFF—Power
status light will
turn OFF.
Standby—Power
status light will
blink.
Hibernation—
Power status light
will turn off.
Briefly press the power button.Powers on the notebook.
Select Start > Turn Off Computer >
Turn Off. If the system has stopped
responding and Windows shut
down procedures cannot be used,
press and hold the power button for
4 seconds to turn off the notebook.
Select Start > Turn Off Computer >
Stand By.
-orAllow the system to time out.
If the unit is already on, briefly
press the power button.
-orPress Fn+F12.
-orAllow the system to time out.
Powers off the notebook.
• Saves significant power.
• Turns off the display and
other components.
• Maintains current session
in RAM.
• Restarts quickly.
• Restores network
connections.
• Saves maximum power.
• Saves current session to
disk, then shuts down.
• Restores network
connections.
You can also customize the way power modes work. See the “Batteries and Power
Management” chapter in this guide.
16Reference Guide
Basic Operation
Operating Your Notebook
To reset the notebook
Occasionally, you may find that Windows or the notebook has stopped responding
and will not let you turn off the notebook. If this happens, try the following in the
order listed:
• If possible, shut down Windows: press CTRL+ALT+DEL, and then select Shut
Down, Restart.
–or, if this fails–
• Press the power button for at least 4 seconds until the display shuts down.
Unsaved data will be lost. Press the power button again to restart.
–or, if this fails–
• Insert the tip of a paper clip into the reset button on the bottom of the notebook,
andthenpressthepowerbuttontorestart.
To reset the notebook while it’s docked in a port replicator, you can press the reset
button on the left side of the port replicator.
To change the boot device
The notebook normally boots from its internal hard disk. You can also boot the
notebook from a floppy disk drive, a CD-ROM drive, or an internal network
interface card.
1. Select Start > Turn Off Computer > Restart.
2. When the logo screen appears, press ESC to display the Boot menu.
3. Use the arrow keys to select the boot device, and press ENTER.
If you want to boot from a specific device whenever it is present, change the boot
order using the BIOS Setup utility. See “Configuring the Notebook” in the
“Troubleshooting and Maintenance” chapter in this guide.
Reference Guide17
Basic Operation
Operating Your Notebook
To use the TouchPad
The TouchPad includes an on-off button so you can turn off the TouchPad to avoid
moving the pointer accidentally when you are typing. The indicator light turns off
when you turn off the TouchPad.
1 Select buttons. The Select buttons work like the left and
right buttons on a standard mouse.
2 TouchPad (touch-sensitive pointing device).
3 TouchPad on-off button and indicator light.
4 Scroll pad. The scroll pad scrolls vertically to display the
contents of the active window.
18Reference Guide
Basic Operation
Operating Your Notebook
To use the function hot keys
The combination of the Fn key plus another key creates a hot key—a shortcut key
sequence—for various system controls. To use a hot key, press and hold Fn, press the
appropriate second key, and then release both keys.
This hot keyDoes this
Fn+F1Decreases the display brightness.
Fn+F2Increases the display brightness.
Fn+F5Toggles among the built-in display, an external
display, and simultaneous display on both.
Fn+F8Toggles the built-in keypad on and off. Does not
affect an external keyboard. If Num Lock is on,
then the numeric functions are active;
otherwise, cursor control is active (as marked
on an external keyboard).
Fn+F12Initiates Hibernation.
Fn+NumLockToggles Scroll Lock on and off.
Fn+Page UpIncreases the audio volume and cancels the
mute setting.
Fn+Page DownDecreases the audio volume.
Fn+BackspaceMutes/unmutes the audio output.
Reference Guide19
Basic Operation
Operating Your Notebook
To use the One-Touch buttons
Your notebook includes five One-Touch buttons that can start any application or
open a document or Web site with a single press.
Press the One-Touch button to open the corresponding application, document, or
Web site.
To program a One-Touch button
1 Select Start > All Programs > Utilities > One Touch.
2 On the One-Touch tab, select the button you want to reprogram.
3 Type a label for the button, and then select the application, document, folder, or
Web site you want the button to open.
4 If you want a label to appear onscreen when you press a One-Touch button,
select that option on the Onscreen Display tab.
20Reference Guide
Basic Operation
Operating Your Notebook
To use the Windows and Applications keys
The Windows key brings up the Windows Start menu. This is the same as selecting
the Start button on the taskbar.
The Applications key brings up the shortcut menu for the current application. This is
the same menu that appears when you right-click while pointing at the application.
This key combinationDoes this
Windows key+ERuns Windows Explorer.
Windows key+F1Runs Windows Help.
Windows key+FRuns Windows Find: Search.
Windows key+MMinimizes all displayed windows.
Shift+Windows key+MReturns all minimized windows to original size.
Windows key+RRuns the Windows Run dialog box.
To use the ALT GR key
Non-U.S. keyboards have an ALT GR key to the right of the spacebar. This is a shift
key that provides access to certain special keyboard characters.
For a character in the lower-right corner of a key, press and hold ALT GR to type the
character.
1Shifted
2Unshifted
3ALT GR
Reference Guide21
Basic Operation
Using CDs or DVDs
Using CDs or DVDs
To insert or remove a CD or DVD
CAUTION
Do not remove a CD or DVD while the notebook is reading it, or the notebook
could stop responding and you could lose data.
To avoid damage to the disk or drive, be sure to press the CD or DVD firmly
onto the spindle.
1. Press the button on the face of the CD or DVD drive. If you are using this drive
for the first time, be sure to remove the cardboard packing insert if present.
2. Press the CD or DVD gently but firmly onto the spindle (label facing up).
–or–
Remove the CD or DVD.
3. Slide the tray back into the module to close it.
If your notebook loses power, you can manually open the drive to remove a CD.
Insert a straightened paper clip into the recessed hole on the front of the drive to
open it.
The location of the CD or DVD drive varies by model.
22Reference Guide
Loading...
+ 88 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.