Hoyles Yellow resettable DPCO call point IP67 User Manual
RESET KEY
(1) PROVIDED
OPERATING ELEMENT
FRONT COVER
WATERPROOF RESET CALL POINT
SURFACE MOUNTING BACK BOX
O RING
EARTHING STRAP
(PROVIDED)
20MM THREADED INSERT & WASHER
NB: M3.5 ALLEN FIXINGS
ALREADY INSTALLED
IN THE FRONT COVER
(6) PROVIDED
FIXINGS No.8 X 1”
(4) PROVIDED
Waterproof ReSet Call Point Series 01 & 11
The IP 67 Waterproof ReSet (WRP) has been designed to deal with today’s difficult and harsh environments. Like the ReSet Call Point
it is a unique fire alarm manual Call Point that mimics the feel of breaking glass whilst offering the user the benefits and safety
advantages of a glass-free resettable operating element. Once activated a warning flag drops in to view easily identifying the Call
Point that has been operated. A key can then reset the unit. The Waterproof ReSet provides an ideal solution for most conventional
fire alarm systems. Ideal for all outside applications such as oil rigs, ships, factory’s as well as wash down areas that are sensitive to
broken glass.
Waterproof ReSet
Series 01 Configuration
Connection Options for
Waterproof ReSet Call
Point Series 01
1
1
2
2
control panel
Option 1 terminals 1 & 2
Normally open switch closing on
alarm
680
4
1
680
1
4
control panel
470
3
1
470
1
3
control panel
Option 2 terminals 1 & 3
Normally open switch closing on
alarm with a 470 ohm resistor fitted
in series with the switch
Option 3 terminals 1 & 4
Normally open switch closing on alarm
with a 680 ohm resistor fitted in series
with the switch
680
470
REAR VIEW
SHOWING TERMINALS
Dia A
Dia B
Dia C
see note
over
1
2
3
5
6
4
RECOMMENDED
TIGHTENING SEQUENCE
Dia D
BACK BOX
IMPORTANT NOTICE
Waterproof ReSet Call Point Series 01 & 11
The IP 67 Waterproof ReSet (WRP) has been designed to deal with today’s difficult and harsh environments. Like the ReSet Call Point
it is a unique fire alarm manual Call Point that mimics the feel of breaking glass whilst offering the user the benefits and safety
advantages of a glass-free resettable operating element. Once activated a warning flag drops in to view easily identifying the Call
Point that has been operated. A key can then reset the unit. The Waterproof ReSet provides an ideal solution for most conventional
fire alarm systems. Ideal for all outside applications such as oil rigs, ships, factory’s as well as wash down areas that are sensitive to
broken glass.
Waterproof ReSet
Series 01 Configuration
Connection Options for
Waterproof ReSet Call
Point Series 01
Option 1 terminals 1 & 2
Normally open switch closing on
alarm
Option 2 terminals 1 & 3
Normally open switch closing on
alarm with a 470 ohm resistor fitted
in series with the switch
Option 3 terminals 1 & 4
Normally open switch closing on alarm
with a 680 ohm resistor fitted in series
with the switch
REAR VIEW
SHOWING TERMINALS
Dia A
Dia B
Dia C
see note
over
1
2
3
5
6
4
RECOMMENDED
TIGHTENING SEQUENCE
Dia D
BACK BOX
IMPORTANT NOTICE
EARTHING STRAP
(PROVIDED)
20MM THREADED INSERT & WASHER
WATERPROOF RESET CALL POINT
SURFACE MOUNTING BACK BOX
O RING
FRONT COVER
74.9mm
64.8mm
84.7mm
5.0mm
O
FIXINGS No.8 X 1”
(4) PROVIDED
74.9mm
OPERATING ELEMENT
NB: M3.5 ALLEN FIXINGS
ALREADY INSTALLED
IN THE FRONT COVER
(6) PROVIDED
RESET KEY
(1) PROVIDED
64.8mm
84.7mm
5.0mm
O
control panel
control panel
control panel
470
470
680
680
1
2
1
3
1
4
1
2
1
470
3
1
680
4
Technical Data for Waterproof ReSet Call Point Series 01 & 11
Waterproof Series 01
Denotes a Waterproof ReSet Call Point that will interface with
most conventional fire alarm systems. It is fitted with two
internal 1 watt resistors 470 and 680 ohm. These are easily
accessed through the installer terminals as illustrated.
Waterproof Series 11
Denotes a Waterproof ReSet Call Point that incorporates two
independent single pole changeover switches providing double
pole changeover contacts. Easily accessed through installer
terminals as illustrated.
Current Rating (Series 01 & 11)
Current Rating (Series 11 only)
3 Amps 12 - 24V DC
3 Amps 125 - 250V AC
Housing and Mounting Box Material Polycarbonate
Electrical Contact Material Silver plated brass
Operating Temperature -20°C - +65°C
Installation Terminal Conductor Size 0.5mm - 2.5mm
Waterproof ReSet Series 01 & 11
Specifications
Dimensions
NB: Switch arrangements shown with WRP ReSet in standby.
Mounting Method
1. Remove the Waterproof ReSet Call Point (WRP) from it’s
packaging. Detach the front cover from the backbox.
The earthing strap will be attached to the back box. You
have a choice to keep or remove the earthing strap.
2. Ensure the conduit or cabling lines up with the
conduit entries located on the top or bottom of the
back box and remove the desired conduit threaded
insert(s). It is recommended that entry to the WRP is
via the one or two 20mm threaded entries on the
bottom of the back box.
3. Take the back box (ensuring the two entries are located
at the bottom) and mark the position for the four fixing
screws.
4. Drill the holes and install the back box using the four
fixing screws and rawl plugs provided.
5. When the wiring connections are complete, fix the front
cover to the back box. There are x6 allen screws evenly
distributed around the front cover. Using the allen key
provided tighten each allen screw by one full turn, then
move onto the next. This will ensure that even pressure
is applied all the way around. See Dia C for
recommendation on the sequence to be used. The
recommended torque for the allen screws is 5 N•m.
In order to achieve IP67 rating, ensure the front cover is
securely tightened to the back box.
Front View
Side View
680
470
Accessories
STI F068 Allen Key
STI M210 WRP Test Key
STI F069 Earth Strap
STI C084 ‘O’ Ring
STI M227 20mm Threaded Insert
STI M228 Waterproof Washer
Technical Data for Waterproof ReSet Call Point Series 01 & 11
Waterproof Series 01
Denotes a Waterproof ReSet Call Point that will interface with
most conventional fire alarm systems. It is fitted with two
internal 1 watt resistors 470 and 680 ohm. These are easily
accessed through the installer terminals as illustrated.
Waterproof Series 11
Denotes a Waterproof ReSet Call Point that incorporates two
independent single pole changeover switches providing double
pole changeover contacts. Easily accessed through installer
terminals as illustrated.
Current Rating (Series 01 & 11)
Current Rating (Series 11 only)
3 Amps 12 - 24V DC
3 Amps 125 - 250V AC
Housing and Mounting Box Material Polycarbonate
Electrical Contact Material Silver plated brass
Operating Temperature -20°C - +65°C
Installation Terminal Conductor Size 0.5mm - 2.5mm
Waterproof ReSet Series 01 & 11
Specifications
Dimensions
NB: Switch arrangements shown with WRP ReSet in standby.
Mounting Method
1. Remove the Waterproof ReSet Call Point (WRP) from it’s
packaging. Detach the front cover from the backbox.
The earthing strap will be attached to the back box. You
have a choice to keep or remove the earthing strap.
2. Ensure the conduit or cabling lines up with the
conduit entries located on the top or bottom of the
back box and remove the desired conduit threaded
insert(s). It is recommended that entry to the WRP is
via the one or two 20mm threaded entries on the
bottom of the back box.
3. Take the back box (ensuring the two entries are located
at the bottom) and mark the position for the four fixing
screws.
4. Drill the holes and install the back box using the four
fixing screws and rawl plugs provided.
5. When the wiring connections are complete, fix the front
cover to the back box. There are x6 allen screws evenly
distributed around the front cover. Using the allen key
provided tighten each allen screw by one full turn, then
move onto the next. This will ensure that even pressure
is applied all the way around. See Dia C for
recommendation on the sequence to be used. The
recommended torque for the allen screws is 5 N•m.
In order to achieve IP67 rating, ensure the front cover is
securely tightened to the back box.
Front View
Side View
Accessories
STI F068 Allen Key
STI M210 WRP Test Key
STI F069 Earth Strap
STI C084 ‘O’ Ring
STI M227 20mm Threaded Insert
STI M228 Waterproof Washer
680
470
128mm
62mm
128mm
119mm
62mm
119mm
Loading...