Page 1
EXITGUARD EX104, EX105 & EX106 24 hour Door Alarm
The EX100 series EXITGUARD provides a simple to operate solution for the 24 hour protection of fire exit and
other doors. A number of options are available that can be set up at the installation stage. The following
features are standard to all EX100 series EXITGUARDs:
Magnetic Door Contact.
Fit to door frame and
protect from moisture
8mm (max gap).
Magnet. Fit to door
& align with contact
6 x AA batteries
(Ex104 versions)
Do NOT power
from 12vdc.
This will result
Bk Rd Yl Bl
Tamper
Volt free auxiliary relay
contacts.
Change on alarm condition
EX105 & Ex106 versions
Tamper
12 vdc Power In Ex105
or
12 vdc Power Out 150ma EX106
F
U
S
E
in damage.
Contact
N E L
220/240vac
EX106 only
Move jumper to select
Lo
Hi
TONE
Jumper links shown in
factory default positions
4Basic Chime repeating at 15 sec intervals [1]
4Auto Reset adjustable 1 sec to 90 secs [2]
4Keyswitch Reset [3]
4Instant Alarm [4]
4Reduced alarm after 2 minutes if not reset
4Delay before alarm without pre-warn [5]
4Delay before alarm with pre-warn [6]
4Low level tamper for 2 mins then every 5 mins
4Tamper omit.
4Low battery warning on set & at 5 min intervals
4Hi & Lo level alarm tones
4LED status indicator
4Double bleep for set, single bleep for un-set.
4Pass through/ safe set facility.
Powered from 6 x AA batteries (supplied) EX104 or from a
12vdc intruder alarm supply Ex105
EX105KM is fitted
with auxiliary volt
free terminals for
remote signalling
of Set/Unset
16vac
from
transformer
COM
NO
NC
COM
NO
K1 K2 To1To2
Yellow
White
Blue
Keyswitch
NC
A1
A2
T1
T2
Alarm
Input
Tamper
Input
10s
RESET
1s
CONTROL
90s
Key Reset
ie 2mins +
-ve
+ve
low pitch tone
On
Off
DELAY
Move jumper to select 15s
alarm delay (DOTL)
Move jumper to select
On
door chime facility
Off
CHIME
Factory
Options
www.hoyles.com
Default
Start
Chime
or
Alarm
Alarm
Auto
or Key
Reset
[3]
Key
Delayed
or Instant
Alarm
Instant [4]
On On On On
Off Off Off Off
DELAY DELAY DELAY DELAY
On On On On
Off Off Off Off
CHIME CHIME CHIME CHIME
Auto reset
Turn pot fully
clockwise to
invoke Key Reset
ie Factory default
Delayed
Chime [1]
Basic CHIME facilty repeats at 15second intervals
Auto Reset time can be adjusted between 1 sec
and 90 secs. Beyond 90 secs it becomes Key Reset
10s
1s
The exact position for maximum reset time
(90 secs) is approx. 2 o'clock. To determine
this position exactly ensure that the door
contact and the tamper loop are both open.
The keyswitch should be in the O (Off)
position. Apply power and switch to the I
(On) position within 3 seconds. The sounder
will give a bleep followed by four rapid bleeps
Turn the potentiometer slowly and observe
the following:
At Key Reset a Chime & no LED
At Max Reset a Barp & no Led
Below Max Reset Silence and steady LED
Warning
at start of
delay
Yes
Tone Select does
not affect any other
programming
90s
[2]
No
Lo
Hi
TONE
Set jumpers for desired operation
Control with
Keyswitch
Note: There are no programming
options for tamper facilities.
Dwg 60095 Iss 3 Oct 13
[1][5][6]
Page 2
EXITGUARD EX104, EX105 & EX106 24 hour Door Alarm
The EX100 series EXITGUARD provides a simple to operate solution for the 24 hour protection of fire exit and
other doors. A number of options are available that can be set up at the installation stage. The following
features are standard to all EX100 series EXITGUARDs:
Magnetic Door Contact.
Fit to door frame and
protect from moisture
8mm (max gap).
Magnet. Fit to door
& align with contact
6 x AA batteries
(Ex104 versions)
Do NOT power
from 12vdc.
This will result
Bk Rd Yl Bl
Tamper
Volt free auxiliary relay
contacts.
Change on alarm condition
EX105 & Ex106 versions
Tamper
12 vdc Power In Ex105
or
12 vdc Power Out 150ma EX106
F
U
S
E
in damage.
Contact
N E L
220/240vac
EX106 only
Move jumper to select
Lo
Hi
TONE
Jumper links shown in
factory default positions
4Basic Chime repeating at 15 sec intervals [1]
4Auto Reset adjustable 1 sec to 90 secs [2]
4Keyswitch Reset [3]
4Instant Alarm [4]
4Reduced alarm after 2 minutes if not reset
4Delay before alarm without pre-warn [5]
4Delay before alarm with pre-warn [6]
4Low level tamper for 2 mins then every 5 mins
4Tamper omit.
4Low battery warning on set & at 5 min intervals
4Hi & Lo level alarm tones
4LED status indicator
4Double bleep for set, single bleep for un-set.
4Pass through/ safe set facility.
Powered from 6 x AA batteries (supplied) EX104 or from a
12vdc intruder alarm supply Ex105
EX105KM is fitted
with auxiliary volt
free terminals for
remote signalling
of Set/Unset
16vac
from
transformer
COM
NO
NC
COM
NO
K1 K2 To1To2
Yellow
White
Blue
Keyswitch
NC
A1
A2
T1
T2
Alarm
Input
Tamper
Input
10s
RESET
1s
CONTROL
90s
Key Reset
ie 2mins +
-ve
+ve
low pitch tone
On
Off
DELAY
Move jumper to select 15s
alarm delay (DOTL)
Move jumper to select
On
door chime facility
Off
CHIME
Factory
Options
www.hoyles.com
Default
Start
Chime
or
Alarm
Alarm
Auto
or Key
Reset
[3]
Key
Delayed
or Instant
Alarm
Instant [4]
On On On On
Off Off Off Off
DELAY DELAY DELAY DELAY
On On On On
Off Off Off Off
CHIME CHIME CHIME CHIME
Auto reset
Turn pot fully
clockwise to
invoke Key Reset
ie Factory default
Delayed
Chime [1]
Basic CHIME facilty repeats at 15second intervals
Auto Reset time can be adjusted between 1 sec
and 90 secs. Beyond 90 secs it becomes Key Reset
10s
1s
The exact position for maximum reset time
(90 secs) is approx. 2 o'clock. To determine
this position exactly ensure that the door
contact and the tamper loop are both open.
The keyswitch should be in the O (Off)
position. Apply power and switch to the I
(On) position within 3 seconds. The sounder
will give a bleep followed by four rapid bleeps
Turn the potentiometer slowly and observe
the following:
At Key Reset a Chime & no LED
At Max Reset a Barp & no Led
Below Max Reset Silence and steady LED
Warning
at start of
delay
Yes
Tone Select does
not affect any other
programming
90s
[2]
No
Lo
Hi
TONE
Set jumpers for desired operation
Control with
Keyswitch
Note: There are no programming
options for tamper facilities.
Dwg 60095 Iss 3 Oct 13
[1][5][6]
Loading...