Hoyles ChatterBox Talking Alarm Module Voice Sounder User Manual

Installation Instructions
TAM401 - ChatterBox Talking Alarm Module
The ChatterBox Talking Alarm Module is a self contained audio module with loud speaker. It can play any type of sound file, be it tones, music or voice. Typical uses include a voice sounder for an intruder alarm, building welcome messages, general alarm messages.
The unit requires a supply of 12vdc which must be present before any sounds can be activated. Four different sounds can be played by activating one of the four inputs. The inputs are normally open and must be closed to activate a sound.
The sound will repeat while the input is held on. When the input is removed, the sound will play until the end of the file and then stop.
If more than one input is applied at a time, the most recently applied input will interrupt any file playing at the time.
The files need to be WAV files, mono, 16bit, 44.1KHz.
The files on the SD card are named TA001.wav, TA002.wav etc. The file TA001.wav corresponds to Input 1 and TA002.wav to Input 2 etc. A list of the messages provided is given on the reverse of this sheet. To actually use a message other than the default TA001 - TA004, you will need to use a PC to rename the file you want to use to TA001.wav, TA002.wav, TA003.wav or TA004.wav.
Connection Details
Power: Note that +ve must be connected to both the Amp and Logic terminals.
Normally open inputs. Close the input for mor than 100ms to play the related sound file.
+12vdc (Amp)
+12vdc (Logic)
-ve
Serial Input
Input 4
Input 1
Input 2
Input 3
Volume adjustment Turn anti clockwise to increase
Dimensions mm
Speaker terminals >=8 Ohms
60
125
175
50
DWG: 60148 iss1 APR 13
List of messages provided on the SD memory card.
File name Message
TA001.wav The system is now set.
TA002.wav The intruder alarm system has activated. The police have been called.
TA003.wav Emergency exit please close the door
TA004.wav Secure store alarm!
TA005.wav The alarm is now set, you have one minute to leave the building, please exit now.
TA006.wav Your presence has been detected; the owner and police have been informed.
TA007.wav Attention! Please close the door.
TA008.wav Attention! Please close the refrigerator door.
TA009.wav Attention! Emergency Access Call Point activated.
TA010.wav Attention! Emergency exit door open.
TA011.wav Attention! Emergency exit door open. Please close the door.
TA012.wav Attention! Disabled toilet alarm activated.
TA013.wav Attention! Panic alarm activated!
TA014.wav Attention! Panic alarm activated! Please call for help!
TA015.wav Warning! The smoke screen system has activated, please vacate the area immediately.
TA016.wav The door is unlocked, please proceed.
TA017.wav Alarm activated
TA018.wav The alarm is now set.
TA019.wav The alarm is un set.
TA020.wav The alarm is now set, you have one minute to leave the building, please exit now.
TA021.wav Warning! Your presence has been detected. You are on private property, the owner and the police
have been informed.
TA022.wav “Alarm Tone 1”
TA023.wav “Alarm Tone 2”
TA024.wav Your presence has been detected; the owner and police have been informed.
TA025.wav System disarmed.
TA026.wav Your presence has been detected; please apply the key within the next 30 seconds.
TA027.wav The alarm is activated, you have 30 seconds to leave the building, please exit now.
TA028.wav The intruder alarm has activated. The police have been called.
TA029.wav Smoking is not permitted at this entrance. please move to a designated smoking area.
TA030.wav As TA029.wav but plays message twice.
TA031.wav Please close the door and swipe access control card before entering or exiting.
TA032.wav This is a no smoking area, please extinguish your cigarette.
TA033.wav Attention! You are being observed by CCTV, please move away from the area immediately.
TA034.wav Attention! Please close the gate.
TA035.wav Attention! Please turn all lights off before exiting.
Other professionally recorded messages available on request.
Loading...