Hotpoint WF430, WF240, WF220, WF440, WF210 User Manual

...
4 (1)
INSTRUCTIONS FOR INSTALLATION & USE for the AQUARIUS RANGE
WF445,WF440,WF430,WF250,WF240,WF225,WF220,WF215,WF210 and WF000
Hotpoint recommends, for your own safety and to ensure you get the best possible results from your
Washing Machine, you read through this booklet and follow these steps thoroughly.
Choose a location for your washing
machine, where possible on a solid
floor,with the electrical sockets and
water supply taps easily accessible.
600m depth and 900mm height.
DO NOT install in a bath or shower
room.
Dispose of packaging material in a safe
place and remove any labels.
Please read instructions thoroughly to
ensure you understand each stage
before you begin.
Read the rest of these instructions to get the best from your appliance, remember to fill in your guarantee registration.
Keep this Book in a safe place for quick reference.
STEP 1 STEP 2
A wash chart is provided to help you to
select your required programme.
Examples are given for the maximum
washing load weights for different fabric
types.
STEP 4
WARNING: This appliance must be earthed.
Remember you may be charged for a service call if a
problem with your washing machine is caused by
incorrect installation or misuse.
Electrical Guide Installation Guide
Programme Selection
Read through this section to familiarise
yourself with the different
compartments within the dispenser
drawer.
STEP 3
Dispenser Drawer
NOTE: Always follow manufacturer’s dosage
recommendations.
All available optional wash features are
explained within this section - These
allow you to adjust your selected wash
programme to suit your needs.
STEP 6
Options Guide
How to start your selected programme
and how to stop or change the
programme if so required.
STEP 5
Using your Machine
NOTE: Progress indicator lights show what stage in
the programme cycle has been reached.
STEP 8
Troubleshooting
A picture guide provides a clear
explanation how to set a wash
programme.
DO NOT overload the washing machine.
STEP 7
A Typical Wash Programme
NOTE: Hotpoint recommend, on completion of
your programme, that you switch off both the
electricity and water supply to the appliance.
Please refer to the Troubleshooting
section if you have any problems when
using your washing machine.
There may be nothing wrong!
NOTE: In addition to the temperature of the
incoming water,the selec tion of optional wash
features will affect the programme times.
READ BEFORE
CONTACTING
SERVICE!
Electricity Supply
WARNING: The appliance must be earthed.
CE marking certifies that this appliance conforms to the following
EEC directives:
Low Voltage Equipment - 72/23/EEC & 93/68/EEC
Electromagnetic Compatibility - 89/336/EEC, 92/31/EEC & 93/68/EEC
Fuses
Your appliance comes fitted with a plug and a 13 amp (13A) fuse. If
you need to replace the fuse,use only those rated at 13 amp (13A)
and ASTA approved to BS1362.To change the fuse lift the holder to
vertical position and lift the fuse out. To replace the fuse, insert the
fuse and push fuse holder down into the locked position. Correct
replacement is identified by colour coding or the marking on base of
plug.
WARNING: Do not use the plug unless the fuse holder is in the locked
position and the top cover firmly replaced.
Changing the Mains Lead
If you have damaged the existing lead and need a new one,contact
Hotpoint Service UK on: 08709 066 066 or
www.theservicecentre.co.uk (or in the Republic of Ireland on: 1850
302 200). A charge will be made.
We strongly advise that fitting a new lead is carried out by a qualified
electrician.
Seek professional advice if you need to use an extension lead.
Changing the Plug
If you need to change your plug, if it does not fit your socket: isolate
the machine from the mains supply. Cut off the supplied plug and
safely dispose of the discarded plug. DO NOT plug into any other
socket.
NOTE: If you change the plug, the colour of wires in the mains lead
may not match the colour of the markings which show the different
terminals in the plug.You must wire it as shown below:
Green and yellow (Earth)
wire to terminal marked ‘E’,
symbol , or coloured
green and yellow.
Blue (Neutral) wire to
terminal marked ‘N’ or
coloured black.
13A ASTA approved fuse to
BS1362.
Brown (Live) wire to terminal
marked ‘L’or coloured red.
STEP 1
2
CONNECT TO THE WATER
SUPPLY...
Installation
ii
i
3
DRAINAGE SYSTEM...we recommend one of the following:
4
LEVEL?...
NOTE: ALTHOUGH YOU MAY NEED TO
MOVE THE HOOKED END SUPPORT
ALONG THE GREY DRAINAGE HOSE,
DO NOT REMOVE IT.
WHICHEVER DRAINAGE METHOD
YOU USE,MAKE SURE THAT THE
HOOKED END SUPPORT IS FIXED
LEVEL TO, OR ABOVE THE ‘PLUMBING
INDICATOR LINE’*
(*see Getting to Know your Appliance)
PLEASE USE THE NEW HOSES SUPPLIED,FITTED
TO THE MACHINE.
If you have no hot water supply...
Old hoses may
cause leaks due to
worn out washers
or may split due to
water pressure.
YOUR MACHINE WILL BE NOISY IF THE TWO FRONT FEET ARE NOT
ADJUSTED SO THE MACHINE STANDS FIRM AND LEVEL.
Check both hot
and cold water
supplies are
running freely...
A cold fill adaptor is available from
your local Hotpoint authorised
Service Centre or by calling the
Genuine Parts & Accessories Hotline
(see KEY CONTACTS).
Connect fill hoses to the
water supply taps:
Red or Grey Hose end to
Hot and Blue Hose end
to Cold.
TURN BOTH TAPS ON...
iv
iii
Check the hoses
at least once a
year.Replace any
that show signs of
cracking, they
might burst due
to water pressure.
Water pressure at the tap
must be in the range...
Max. 1Mpa (10 bar) and
Min. 0.05Mpa (0.5 bar)
- Move your machine into final location.
Take care not to trap or kink the hoses.
- Turn one or both front feet clockwise until
the machine stands firm and level.
The spring on each foot will stop them
coming loose.
If it is placed on a fitted carpet, adjust the feet
to ensure that there is adequate ventilation
beneath the washing machine.
1
REMOVE TWO TRANSIT FIXINGS... Follow these instructions to remove the TWO transit fixings.
IMPORTANT:
Situated, one either
side of the rear panel,
both transit bolts
(complete with
spacers) MUST be
removed before use...
Failure to do so may
cause damage to
your machine!
DO NOT REMOVE!
STANDPIPE METHOD
UNDER SINK METHOD
TECHNICAL DETAILS
OR
Attach the GREY
drainage hose to the
under sink drainage
unit securely,using a
hose clip.
Fix the hooked
end support at
a minimum
800mm from
the floor.
cut off the blocked
end of the under sink
drainage unit.
6
READY...
TO CHECK ALL PARTS OF THE INSTALLATION AND TO THOROUGHLY
CLEAN THE INSIDE OF YOUR MACHINE:
RUN PROGRAMME ‘B’ (refer to ‘Programme Selection’, STEP 4).
5
CONNECT TO THE POWER SUPPLY...
PLUG YOUR MACHINE INTO AN ELECTRICAL SOCKET WHICH IS
EASILY ACCESSIBLE. SWITCH ON
NOTE: Hotpoint recommend extension
leads are not used.
NOTE: The mains cable must only be
replaced by an authorised serviceman.
WITHOUT ANY LAUNDRY
WITHOUT ANY DETERGENT
and
THIS WILL TAKE APPROXIMATELY 2hours 30minutes TO COMPLETE
.............................
Standpipe height:
minimum 500mm
from the floor.
Insert drainage hose
approximately 100mm
into the standpipe.
It is important the transit
bolt and spacer come out
intact (see pic).
For safety,replace both
plastic covers over the
holes left by removing
the two bolts.
Use a crosshead
screwdriver to
remove the
plastic cover.
Unscrew the
bolt using a
13mm spanner.
ST
OP when 3
threads can be
seen.
Hold, slide
across and pull
to remove.
800mm
from floor
Hooked End Support
STEP 2
The inclination of the machine, measured on the top, must not exceed 2˚.
Models
Dimensions
Capacity
Electric
Connections
Spin Speed
Control
programmes
according to
IEC456
directive
WF445,WF440,WF430,WF250,
WF240,WF225,WF220, WF215,
WF210 and WF000
59.5cm wide
85cm high
60cm deep
from 1 to 6kg
voltage 220/230 Volts 50Hz
maximum absorbed power 1700W
up to 1500rpm - WF250
up to 1400rpm - WF445,WF440
& WF240
up to 1300rpm - WF430
up to 1200rpm - WF225 & WF220
up to 1100rpm - WF215 & WF210
up to 1000rpm - WF000
programme D
temperature 60˚C
run with a 6kg load
The Dispenser Drawer
STEP 3
Adding Fabric Conditioner
Dispensing Powder Detergent
Dispensing Liquid Detergent
Index:
1. Drawer release latch
2. Pre-wash detergent compartment
Maximum 200ml powder or
100ml liquid
3. Main detergent compartment
Maximum 400ml powder or
200ml liquid
4. Grate
5. Fabric conditioner compartment
120ml maximum
1
2
3
4
5
To achieve the best wash results the manufacturer’s
recommended amount of detergent should be measured
and added to the main detergent compartment (II symbol)
(max. 400ml).
Pour the recommended amount of fabric conditioner into the
compartment (flower symbol).
Do not exceed the maximum fill line.
Pre-wash Programme A
When selecting programme A add detergent to both the pre-wash compartment
(I symbol) and the main wash compartment (II symbol).
DO NOT use in drum dosing devices with Pre-wash programme A.
WARNING:
Do not put any items into
the drawer, other than
detergents designed to be
released from the drawer, as
they may cause damage or
blockage.
We recommend the use of a detergent dosing ball, as provided by your detergent
manufacturer.
Loading...
+ 7 hidden pages