Hotpoint WD63, WD64 User Manual
INSTRUCTIONS FOR INSTALLATION & USE
WD63,WD64
Hotpoint recommends,for your own safety and to ensure you get the best possible results from your Washer
Dryer,you read through this booklet and follow these steps thoroughly.
STEP 1 STEP 2
Choose a location for your washer dryer,
where possible on a solid floor,with the
electrical sockets and water supply taps
Electrical Guide Installation Guide
easily accessible.
Allow sufficient space: 600mm width,
600m depth and 900mm height.
DO NOT install in a bath or shower
room.
WARNING: This appliance must be earthed.
Dispose of packaging material in a safe
place and remove any labels.
Please read through thoroughly to
ensure you understand each stage
before you begin.
Remember you may be charged for a service call if a
problem with your washer dryer is caused by
incorrect installation or misuse.
STEP 3
Dispenser Drawer
Read through this section to familiarise
yourself with the different
compartments within the dispenser
drawer.
STEP 4
Wash Guide
A wash chart is provided to help you to
select your required programme.
Examples given for the maximum
washing load weight for different fabric
Hotpoint recommend the Persil range of
NOTE: Always follow manufacturer’s dosage
STEP 5
Options Guide
detergent products.
recommendations.
All available optional wash features are
explained within this section - These
allow you to adjust your selected wash
programme to suit your needs.
STEP 6
types.
Drying Guide
A guide to drying times is provided for
independent drying programmes, along
with a list of items not suitable for
tumble drying.
Examples given for the maximum drying
load weight for different fabric types.
NOTE: In addition to the temperature of the
incoming water,the selection of optional wash
features will affect the programme times.
STEP 7
Wash & Auto Dry Programme
A picture guide provides a clear
explanation how to set a wash and auto
dry programme.
DO NOT overload the washer dryer.
NOTE: Hotpoint recommend, on completion of
your programme, that you switch off both the
electricity and water supply to the appliance.
STEP 8
READ BEFORE
CONTACTING
SERVICE!
NOTE: Always make sure the mains button is in the
OFF position before selecting an independent
drying programme.
Troubleshooting
Please refer to the Troubleshooting
section if you have any problems when
using your washer dryer.
There may be nothing wrong!
Read the rest of these instructions to get the best from your appliance, remember to fill in your guarantee registration.
Keep these instructions in a safe place for quick reference.
STEP 1
Electricity Supply
STEP 2
WARNING: The appliance must be earthed.
Fuses
Your appliance comes fitted with a plug and a 13A fuse. If you need to
replace the fuse,only those rated at 13A and ASTA approved to
BS1362 should be used.To change fuse lift holder to vertical position
and lift fuse out.To replace, insert fuse and push fuse holder down
into locked position. Correct replacement is identified by colour coding or the marking on base of plug.
WARNING: Do not use plug unless fuse holder is in locked position.
Changing the Mains Lead
A special lead can be ordered from Hotpoint Service
UK: 08709 066 066 or Republic of Ireland: 1850 302 200
If you have damaged the existing lead or require a longer one a
charge will be made. It is strongly advised that this work is carried out
by a qualified electrician.
Changing the Plug
Cut off and dispose of the supplied plug if it does not fit your socket.
WARNING:To avoid a shock hazard do not insert the discarded plug into
a socket anywhere else.
IMPORTANT: WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Green/Yellow - Earth
Blue - Neutral
Brown - Live
If you change the plug, the colour of wires in the mains lead may not
correspond with the colour of the markings identifying terminals in
the plug.You should therefore wire it as shown:
Green and yellow (Earth)
wire to terminal marked ‘E’,
symbol , or coloured
green and yellow.
Blue (Neutral) wire to
terminal marked ‘N’or
coloured black.
13A ASTAapproved fuse to
BS1362.
Brown (Live) wire to terminal
marked ‘L’ or coloured red.
1
POLYSTYRENE BLOCK...
NOTE: YOU MAY NEED A SECOND PERSON TO HELP YOU
RAISE AND LOWER THE APPLIANCE.
This is part of the packaging
and should have come away
with the polystyrene base -
IF IT HAS NOT... REMOVE IT!
4
NOTE:
MOV
ALON
WHI
YOU
HOO
LEVEL
DRA
(*see
5
LEVEL?...
YOUR MACHINE WILL BE NOISY IF THE TWO
NOT ADJUSTED SO THE MACHINE STANDS F
Each foot has two parts: The Locking Disk a
Locking
Disk
CE marking certifies that this appliance conforms to the following
EEC directives:
Low Voltage Equipment - 72/23/EEC & 93/68/EEC
Electromagnetic Compatibility - 89/336/EEC, 92/31/EEC & 93/68/EEC
Foot
Release the locking disk on the
i
two front feet and screw the feet
in or out until the machine stands
firm and level.
Turn ON
ii
on the t
each is
of the m
Installation
2
REMOVE TRANSIT BRACKETS...
IMPORTANT:
Internal transit brackets
are fitted to prevent
damage during transit
and MUST be removed
before use...
Failure to do so may
cause damage to your
Remove and
retain 3 screws
from the back of
the worktop lid
Slide and push worktop lid back
into position, ensuring front edge is
correctly located into the console.
From the rear of the
machine, grip sides of
the worktop lid, lift,slide
and pull towards you.
machine!
DRAINAGE SYSTEM...we recommend one of the following:
STANDPIPE METHOD
Hooked End Support
Insert drainage hose
DO NO
T REMOVE IT.
approximately 100mm
into the standpipe.
.............................
Standpipe height:
minimum 500mm
from the floor.
OR
Remove 4 screws
and the rear transit
bracket - retain.
Replace the work top lid
using the 3 original screws.
UNDER SINK METHOD
cut off the blocked
end of the under sink
drainage unit.
Remove 3 screws
and front transit
bracket - retain.
3
PLEASE USE THE NEW HOSES
SUPPLIED, FITTED TO THE
MACHINE.
DO NOT REMOVE!
800mm
from floor
Fix the hooked
end support at
a minimum
800mm from
the floor.
CONNECT TO THE
Old hoses may cause leaks
due to worn out washers.
Attach the GREY
drainage hose to the
under sink drainage
unit securely,using a
hose clip.
6
CONNECT TO THE POWER SUPPLY...
PLUG YOUR MACHINE INTO AN ELECTRICAL SOCKET WHICH IS
EASILY ACCESSIBLE. SWITCH ON
NOTE: Hotpoint recommend
extension leads are not used.
Move your machine into position,
take care not to trap or kink the
hoses.
7
READY...
TO CHECK ALL PARTS OF
CLEAN THE INSIDE OF YO
SELECT A 95˚ WHITE CO
WITHO
✗
THIS WILL TAKE APP
STEP 3
The Dispenser Drawer
Check both hot and
i
cold water supplies
are running freely...
Connect fill hoses to
ii
water supply taps:
- Red or Grey Hose
end to Hot
- Blue Hose end to
Cold
TURN ON BOTH TAPS
If you have no hot water
supply...
A cold fill adaptor is
available from your local
Hotpoint authorised Service
Centre or by
calling the
Genuine
Parts &
Accessories
Hotline
(see KEY
CONTACTS).
Changing the Main
Wash Indicator:
The main wash indicator
has been fitted to
dispense powder
detergent only.
If you wish to use liquid
detergent, reposition the
main wash indicator as
shown below:
Pull the drawer out until
1
it reaches its stop.
Press down on button,
2
to release the drawer
latch and remove the
drawer.
1
2
3
4
5
6
Index:
1. Drawer latch
2. Button
3. Main wash
indicator
4. Main wash
compartment
5. Prewash
compartment
6. Fabric conditioner
compartment.
Dispensing Powder
Detergent
To achieve optimum wash
results we recommend that
you use the detergent
manufacturers dispensing
cup, to dispense no more
than 300ml of powder.
and
WITHOUT ANY DETERGENT
✗
Lift the main wash
3
indicator out of slots,
rotate and reposition for
Liquid, ensuring it is
secure.
Relocate the drawer and
4
push back into place.
Dispensing Fabric
Conditioner
Pour fabric conditioner into
the compartment.
We recommend that you do
not exceed the maximum
level indicated.
Cleaning the Dispenser Drawer &
Compartments:
It is advisable to clean the dispenser
drawer regularly:
Remove the drawer, see ‘Changing
the Main Wash Indicator’, wash
the dispenser drawer and clean
out the compartment.
Dry thoroughly and relocate.
Loading...