Hotpoint TVEL 75C Experience, TVYL 75C Style Instruction Booklet

Instruction booklet

TUMBLE DRYER

GB

English

! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and
should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the
dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.
! Read these instructions carefully; the following pages contain important information on installation and suggestions
on how the appliance works.

This symbol reminds you to read this booklet.

1

Contents

TVEL 75C Experience
TVYL 75C Style

Important information, 2

Installation, 3-4

Where to put your dryer
Ventilation
Electrical connection
Levelling your dryer
Before you start using your dryer

Dryer description, 5

The front
The back
Control panel

Start and programmes, 6-10

Choosing a programme
Tables of Programmes
The controls

Laundry, 11-12

Sorting your laundry
Wash care labels
Special clothing items
Drying times

Warnings and Suggestions, 13

General safety
Saving energy and respecting the environment

Maintenance and Care, 14

Switching off the electricity
Cleaning the filter after each cycle
Check the drum after each cycle
Cleaning the dryer

Troubleshooting, 15

Service, 16

Disposal

Hotpoint Guarantee, 19

Hotpoint After Sales Service, 20

GB

Important

Information Installation Description The Display

Start and

Programmes Laundry

Warnings and

Suggestions Troubleshooting Ser vice

Maintenance

and Care

2

GB

Important Information

! You MUST clean the fluff filter after EVERY drying
cycle.

Fluff Filter...

! Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine.

- It will take longer to dry and as a result will use more electricity during drying.

STEP 1.

Open the door of your
dryer.

STEP 2.

Pull out the filter (using
the two finger grips).

STEP 3.

Open the filter and clean
any fluff deposits from
the filter mesh.

For your Venting dryer to operate efficiently, you must follow the regular maintenance schedule shown below:

STEP 4.

Refit the filter, with the
curved side towards you.

STEP 5.

Make sure the filter is
pushed fully home.

- NEVER run the dryer
without the filter in position.

! You MUST clean fluff build up around the filter housing and the vent tube periodically, EVERY two or three months:

- Check the vent tube and any permanent venting fixture to make sure that there has been no accumulation
of fluff or lint, and remove it.

- Remove lint that collects around the filter and the outlet vents.

3

GB

Description The Display

Start and

Programmes Laundry

Warnings and

Suggestions Troubleshooting Ser vice

Maintenance

and Care

Installation

Permanent venting

In conjunction with the vent tube we recommend
using a Wall/Window Vent Kit, available at a retail
location or the nearest Spare Parts Dealer.

Wall mounting

1. Leave an opening in
the wall to the left of the
dryers proposed position.

2. Keep the tube as short
and straight as possible
to prevent condensed
moisture from backing up
into the dryer.

3. Similarly, the duct in
the wall should slope
downwards towards the
outside.

Window mounting

1. With a stacked dryer
the hole in the window
should ideally be made
below the vent.

2. The tube should be
kept as short as possible.

Depending on how often you use your dryer, it is
essential that areas A and B are checked periodically
to remove lint or debris.
The vent tube adaptor must be fitted securely thus
preventing any humid air from being emitted back into
the room.
! The Dryer should not be pushed so far back that the
tube adaptor is pulled out of position or the tube is
squashed or bent.
! The tube should be kept clear of the air intake vent
and kinks or ‘U’ bends must be avoided as these will
obstruct the tube or trap condensation.

Where to put your dryer

●

Place your dryer at a distance from gas ranges,
stoves, heaters, or cook tops because flames can
damage the appliance.

●

If you are going to install the
appliance under a work
counter, be sure to leave a
10mm space between the
top and any other objects on
or above the machine and a
15mm space between the
sides and lateral furnishings

or walls. This is to ensure
proper air circulation. Make sure that the back
vents are not obstructed.

●

Make sure you put your dryer in an environment
that is not damp and has proper air circulation
throughout, the dryer will not operate efficiently in
an enclosed space or cupboard.

! We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed
behind a lockable door, a sliding door or a door with a
hinge on the opposite side to that of the dryer door.

Ventilation

The Dryer dries your laundry by drawing in cool, clean
and relatively dry air, heating it, and then distributing it
through the clothes as they are gently tumbled. For
optimum performance, the moist air is then blown out
through a vent tube at the back of the dryer.
When the dryer is in use, there has to be adequate
ventilation to avoid the back flow of gases into the room
from appliances burning other fuels, including open fires.

Mobile venting

A vent tube must always be fitted when the dryer is
used in conjunction with Mobile Venting.
The tube must be fitted securely into the back of the
dryer (see Dryer Description). If possible, it is always
best to connect the tube to a permanent
outlet close to the dryer. If permanent installation is
not possible, the dryer will work just as well with the
tube passing through a partly-opened window.

! Ensure that the end of the tube is not directed
toward the air intake vent at the rear of the dryer.

! The vent tube should not exceed 2.4 metres in
length and should be kept free of any possible
accumulation of fluff, lint and water by shaking it out
frequently. Always ensure that the tube is not
squashed.

Minimum gap 10mm

Minimum gaps

15mm

Important

Information Installation

4

GB

Installation

Open window venting

The end of the tube
should be directed
downwards, to prevent
warm moist air from
condensing in the room or
in the dryer.

! Ensure that the dryer is adequately ventilated and
that the end of the vent tube is not directed towards
the air intake duct.
! The vent tube must always be fitted for optimum
performance.
! Make sure that the vent tube and air intake vents are
not obstructed or blocked.

! The dryer must not recycle exhaust air.
! Misusing a tumble dryer may create a fire hazard.
! Do not discharge exhaust air into a flue which is

used for exhaust fumes from other appliances that
burn gas or other fuels.
! Do not discharge exhaust air into an extraction
system or any duct with an extractor fan. This will
affect the way the thermal controls operate and can
result in a fire hazard.

Electrical connections

Make sure of the following before you insert the plug
into the the electrical socket:

●

The socket must be grounded.

●

The socket must be able to sustain the machines
maximum power, which is indicated on the rating
label (see Dryer Description).

●

Power voltage must be within the values indicated
on the rating label (see Dryer Description).

●

The socket must be compatible with the dryers
plug. Should this not be the case, replace the
plug or the socket.

! The dryer must not be installed outdoors, even if the
space is sheltered. It can be very dangerous if it is
exposed to rain or storms.
! Once installed, the dryers electrical wire and plug
must be within easy reach.

! Do not use extension cords.
! The power cord must not be bent or squashed.
! The power cord supplied is fitted with a BS1363 plug

and a 13 amp BS1362 fuse. If you need to replace the
fuse, use only those rated at 13 amp (13A) and ASTA
approved to BS1362.

Moulded plug

! The plug must not be used
without the fuse cover in place. If
a replacement fuse holder/cover is
required, it must be of the same
colour coding or wording as
shown on the base of the plug.
Replacements are available from
authorised dealers.

Green and Yellow
(Earth) wire to terminal
marked ‘E’, symbol ,
or coloured green and
yellow.

13A ASTA approved
fuse to BS1362.

Brown (Live) wire to
terminal marked ‘L’ or
coloured red.

Blue (Neutral) wire to
terminal marked ‘N’ or
coloured black.

Cord clamp

Changing the plug

The wires in the power cord are coloured in accordance
with the following:

! If the plug being replaced is a non-rewirable type,
then the cut-off plug must be disposed of safely. DO
NOT leave it where it can be inserted into a socket
and create a shock hazard.
! The power supply cord should be checked periodically
and replaced by a cord specially prepared for this
dryer and fitted only by authorised technicians (see
Service). New or longer power cords are supplied at
an extra charge by authorised dealers.
! The manufacturer denies any responsibility should
any of these rules not be followed.
! If in doubt about any of the above consult a qualified
electrician.

Levelling your dryer

The dryer must be installed level for correct operation.

When you have installed your
dryer in its final location check
that it is level first side to side,
then front to back.

If the dryer is not level, use a
wooden block to
support it while adjusting the two
front legs up or down, until your
dryer is level.

Before you start using your dryer

Once you have installed your dryer and before you
use it, clean the inside of the drum to remove any dust
that could have accumulated during transport.

5

Dryer Description

GB

Important

Information Installation Description The Display

Start and

Programmes Laundry

Warnings and

Suggestions Troubleshooting Ser vice

Maintenance

and Care

button in pauses the programme and stops the dryer.
The light is green when programme is running, flashing
amber if the programme has been paused or flashing
green if on standby waiting to start a programme (see
Start and Programmes).
Note: This light also flashes amber during the Post
Care phase of a programme.

The Progress or Delay lights show you the status of
the programme, or the delay time when they flash.
During a delayed start the lights flash to show the
delay selected. When (not flashing) they show each
stage of the programme by the corresponding light
turning on (see Start and Programmes).

The Clean Filter light gives you a reminder before
every programme that it is essential to clean the filter
every time the dryer is used (see Maintenance and Care).

The ON/OFF button : If the dryer is running and
this button is pressed and held for more than 3
seconds, the dryer is turned off. Press and hold again
for more than 3 seconds and the dryer reactivates.

The PROGRAMMES knob sets the programme: rotate
it until the indicator is pointing to the programme you want
to select (see Start and Programmes).

The OPTION buttons/lights select available options for
your selected programme. The lights indicate that the
option has been selected. If an option is not available
the buzzer will beep three times (see Start and
Programmes).

The START/PAUSE button/light starts a selected
programme. When you press this button there will be
one beep and the progress lights will flash to confirm
the action. When a programme is running, holding this

Control panel

PROGRAMMES

Knob

START/PAUSE

Button & Light

Indicator

Progress or Delay

Lights

OPTION

Buttons & Lights

Clean Filter

Light

ON/OFF

Button

Control Panel

Drum

Model & Serial
numbers

Filter

The front The back

Air Intake Vent

Vent Tube fitted here

Caution: Hot!

Rating plate

6

GB

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see

Laundry).

3. Open the door and make sure the filter is clean

and in place (see Maintenance).

4. Load the machine and make sure items are not in

the way of the door seal. Close the door.

5. If none of the lights are on: Press the ON/OFF

button .

6. Choose a programme by checking the Programmes

Guide (see Programmes) as well as the indications
for each type of fabric (see Laundry).

- Select a programme by rotating the
PROGRAMMES knob.

7. Set a delay time and other options if necessary.

8. The START/PAUSE light is flashing green:

- press the START/PAUSE button to begin.
The green light stops flashing.

Start and Programmes

Shirts Light Dry

High heat option

●

This is a programme for shirts made from cotton.

●

It can be used for load sizes up to 3kg (approximately 10 shirts).

●

This programme will take about 80 minutes, but may take longer depending on the size of the load and the spin
speed used in your washer.

Low heat option

●

This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such
as polyester and cotton.

●

It can be used for load sizes up to 3kg (approximately 14 shirts).

●

This programme will take about 65 minutes, but may take longer depending on the size of the load and the spin

speed used in your washer.
Shirts dried using this programme are usually ready to put away, the edges or seams may be slightly damp. If this is
the case, try turning the shirts inside out and running the programme again for a short period.

Jeans

●

This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.

●

It can be used for load sizes up to 3kg (approximately 4 pairs).

●

Do not mix dark and light coloured items.

●

It can also be used on other garments made from the same material, such as jackets.

●

This programme will take about 85 minutes, but may take longer depending on the size of the load and the spin

speed used in your washer.

●

Loads dried using this programme are usually ready to wear, the edges or seams may be slightly damp. If this is

the case, try turning the jeans inside out and running the programme again for a short period.
! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.

Note:

This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is detected. Press the ON/OFF button briefly and wait for the
dryer to reactivate.

During the drying programme, you can check on
your laundry and take out items that are dry
while others continue drying. When you close
the door again, press the START/PAUSE button in
order to resume drying.
(When the door is opened the START/PAUSE light

will flash Amber, after the door is closed and the
START/PAUSE button pressed, the START/PAUSE
light will stop flashing and show green.)
Note: During the Post Care phase this light
flashes Amber.

9. To let you know that your programme is complete
the buzzer will beep 3 times. (Note: If the SOUND
option was selected the buzzer beeps 3 times
every 30 seconds for 5 minutes).
Open the door, take the laundry out, clean the filter
and replace it (see Maintenance).
If the Crease Care option has been selected and
you do not remove the laundry immediately, the
dryer will tumble occasionally for 10 hours or until
you open the door.

10. Unplug the dryer.