Hotpoint TCAL User Manual

Instruction booklet

TUMBLE DRYER

Contents

Important information, 2-3

Installation, 4

Where to put your dryer Ventilation Water drain Electrical connection Before you start using your dryer

Dryer description, 5

The features Control panel

Start and programmes, 6-10

Choosing a programme Special programmes Programmes Table The Controls

Laundry, 11-12

Sorting your laundry Wash care labels Special clothing items Drying times

Warnings and Suggestions, 13

General safety Saving energy and respecting the environment

Maintenance and Care, 14

Switching off the electricity Cleaning the filter after each cycle Check the drum after each cycle Empty the water container after each cycle Cleaning the condenser unit Cleaning the dryer

Troubleshooting, 15

Service, 16

Disposal

Hotpoint Guarantee, 19

Hotpoint After Sales Service, 20

English

TCAL 83

! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the appliance works. ! Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works.

This symbol reminds you to read this booklet.

Important

Information

Installation Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care Service

Troubleshooting

Important Information

! You MUST clean the fluff filter after EVERY drying cycle.

Fluff Filter...

! Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine.

- It will take longer to dry and as a result will use more electricity during drying.

! You MUST empty the water container after EVERY drying cycle.

Water Container...

Priming the Water Collection System

When your dryer is new, the water container will not collect water until the system is primed... this will take 1 or 2 drying cycles. Once primed it will collect water during every drying cycle.

STEP 1.

Open the door of your dryer.

STEP 2.

Remove the filter.

STEP 3.

Open the filter and clean any fluff deposits from the filter mesh.

STEP 4.

Refit the filter - NEVER run the dryer without the filter in position.

For your Condenser dryer to operate efficiently, you must follow the regular maintenance schedule shown below:

STEP 1.

Pull the water container towards you and remove it fully from the dryer.

STEP 2.

Remove either the small or large cap and empty the water from the container.

! Failure to empty the water container will result in:

- The machine will stop heating (so the load may still be wet at the end of the drying cycle).

- The ‘Empty Water’ light will tell you that the water container is full.

STEP 3.

Refit the water container, ensuring that it is pushed fully back into position.

! The ‘Empty Water’ light reminds you to empty the water

container at the start and at the end of each programme.

Important

Information

Installation Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care Service

Troubleshooting

Important Information

Condenser Unit...

! You MUST clean the fluff from the condenser EVERY month.

! Failure to clean the condenser could cause premature failure of your dryer.

●

Check that:

- The positioning arrows are pointing upwards.

- The 3 clips are re-secured back into their ‘lock’ position.

STEP 3.

Flush the condenser, from the rear with water, to remove any fluff deposits.

STEP 4.

Refit the condenser unit

- ensure that the unit is pushed in fully, all 3 clips are re-secured and the positiong arrows on the front of the condenser are pointing upwards.

Rotate 3 clips

STEP 1.

Open the condenser cover

- hold the handle and pull towards you.

STEP 2.

Remove the condenser by rotating the 3 clips then pulling the condenser towards you. (There may be some water in the tubes, this is normal).

Installation

Moulded plug

! The plug must not be used without the fuse cover in place. If a replacement fuse holder/cover is required, it must be of the same colour coding or wording as shown on the base of the plug. Replacements are available from authorised dealers.

Changing the plug

The wires in the power cord are coloured in accordance with the following:

! If the plug being replaced is a non-rewirable type, then the cut-off plug must be disposed of safely. DO NOT leave it where it can be inserted into a socket and create a shock hazard. ! The power supply cord should be checked periodically and replaced by a cord specially prepared for this dryer and fitted only by authorised technicians (see Service). New or longer power cords are supplied at an extra charge by authorised dealers. ! The manufacturer denies any responsibility should any of these rules not be followed. ! If in doubt about any of the above consult a qualified electrician.

Before you start using your dryer

Once you have installed your dryer and before you use it, clean the inside of the drum to remove any dust that could have accumulated during transport.

Where to put your dryer

●

Place your dryer at a distance from gas ranges, stoves, heaters, or cook tops because flames can damage the appliance.

●

If you are going to install the appliance under a work counter, be sure to leave a 10mm space between the top and any other objects on or above the machine and a 15mm space between the sides and lateral furnishings or walls.

This is to ensure proper air circulation.

Ventilation

When the dryer is in use, there has to be adequate ventilation. Make sure you put your dryer in an environment that is not damp and has proper air circulation throughout. Airflow around the dryer is essential to condense the water produced during the washing, the dryer will not operate efficiently in an enclosed space or cupboard. ! If using the dryer in a small or cold room some condensation could be experienced. ! We do not recommend that the dryer is installed in a cupboard but the dryer must never be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the dryer door.

Water drain

If your dryer is installed next to a drain the water can be plumbed into this drain. This does away with the need to empty the water container. If the dryer is stacked onto or installed next to a washing machine it can share the same drain. The height of the drain must be less than 3' (1m) from the bottom of the dryer.

Remove hose from position shown (see diagram).

Fit a suitable length of hose to the new location shown (see diagram).

! Make sure that the hose is not squashed or kinked when the dryer is in its final location.

Electrical connections

Make sure of the following before you insert the plug into the the electrical socket:

●

Ensure your hands are dry.

●

The socket must be grounded.

●

The socket must be able to sustain the machines maximum power, which is indicated on the rating label (see Dryer Description).

●

Power voltage must be within the values indicated on the rating label (see Dryer Description).

●

The socket must be compatible with the dryers plug. Should this not be the case, replace the plug or the socket.

! Do not use extension cords. ! The dryer must not be installed outdoors, even if the space is

sheltered. It can be very dangerous if it is exposed to rain or storms. ! Once installed, the dryers electrical wire and plug must be within easy reach.

! The power cord must not be bent or squashed. ! The power cord supplied is fitted with a BS1363 plug and a 13

amp BS1362 fuse. If you need to replace the fuse, use only those rated at 13 amp (13A) and ASTA approved to BS1362.

Green and Yellow (Earth) wire to terminal marked ‘E’, symbol , or coloured green and yellow.

13A ASTA approved fuse to BS1362.

Brown (Live) wire to terminal marked ‘L’ or coloured red.

Blue (Neutral) wire to terminal marked ‘N’ or coloured black.

Cord clamp

Minimum gap 10mm

Minimum gaps

15mm

Remove hose from

here...

...fit new hose here.

Important

Information

Installation Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care Service

Troubleshooting

Dryer Description

The Progress or Delay lights show you the status of the programme, or the delay time when they flash. During a delayed start the lights flash to show the delay selected. When (not flashing) they show each stage of the programme by the corresponding light turning on (see Start and Programmes).

The Empty Water indicator light signals that the water container should be emptied. The light will take a few seconds to go out after replacing the empty water container, the dryer must be running for this to happen (see The Controls). Note: If the water bottle fills the indicator light flashes, the heat is turned off and your clothes will not dry.

The Clean Filter light gives you a reminder before every programme that it is essential to clean the filter every time the dryer is used (see Maintenance and Care).

The Clean Condenser light gives you a reminder that it is essential to clean the condenser at regular intervals (see Maintenance and Care).

The ON/OFF button : If the dryer is running and this button is pressed, the dryer stops. Press again, the dryer restarts.

The PROGRAMMES knob sets the programme: rotate it until the indicator is pointing to the programme you want to select (see Start and Programmes).

The OPTION buttons/lights select available options for your selected programme. The lights indicate that the option has been selected (see Start and Programmes).

The START/PAUSE button/light starts a selected programme. When you press this button there will be one beep and the progress lights will flash to confirm the action. When a programme is running, holding this button in pauses the programme and stops the dryer. The light is green when programme is running, flashing amber if the programme has been paused or flashing green if on standby waiting to start a programme (see Start and Programmes). Note: This light also flashes amber during the Heat & Enjoy programme and during the Post Care phase of a programme.

Control panel

Empty Water

Light

PROGRAMMES

Knob

START/PAUSE

Button & Light

Indicator

Progress or Delay

Lights

OPTION

Buttons & Lights

Clean Filter

Light

Clean Condenser

Light

ON/OFF

Button

The features

Water container

Filter

Condenser cover

Rating plate

Model & Serial numbers

Condenser cover handle (Pull to open)

Air intake grille

Start and Programmes

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see Laundry).

3. Open the door and make sure the filter is clean and in place and the water container is empty and in place (see Maintenance).

4. Load the machine and make sure items are not in the way of the door seal. Close the door.

5. If none of the lights are on: Press the ON/OFF button .

6. Choose a programme by checking the Programmes Guide (see Programmes) as well as the indications for each type of fabric (see Laundry).

- Select a programme by rotating the PROGRAMMES knob.

7. Set a delay time and other options if necessary.

Shirts

High heat option

●

This is a programme for shirts made from cotton.

●

It can be used for load sizes up to 3kg (approximately 10 shirts).

●

This programme will take about 80 minutes, but may take longer depending on the size of the load and the spin speed used in your washer.

Low heat option

●

This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such as polyester and cotton.

●

It can be used for load sizes up to 3kg (approximately 14 shirts).

●

This programme will take about 65 minutes, but may take longer depending on the size of the load and the spin

speed used in your washer. Loads dried using this programme are usually ready to wear, the edges or seams may be slightly damp. If this is the case, try turning the shirts inside out and running the programme again for a short period.

Jeans

●

This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.

●

It can be used for load sizes up to 3kg (approximately 4 pairs).

●

Do not mix dark and light coloured items.

●

It can also be used on other garments made from the same material, such as jackets.

●

This programme will take about 85 minutes, but may take longer depending on the size of the load and the spin

speed used in your washer.

●

Loads dried using this programme are usually ready to wear, the edges or seams may be slightly damp. If this is

the case, try turning the jeans inside out and running the programme again for a short period. ! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.

Note:

This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected. Press the ON/OFF button briefly and wait for the machine to start up again.

Anti Allergy Programme

This programme is a treatment used to minimise or eliminate the House Dust Mite or Pollen in the load. In the drying process mites are killed by the high temperature and the low humidity environment. Can be used on a wet load to dry and treat, or on a dry load just to treat your laundry. Maximum load is 8kg for a wet load and 4kg for a dry load.

8. The START/PAUSE light is flashing green:

- press the START/PAUSE button to begin. The green light stops flashing. During the drying programme, you can check on your laundry and take out items that are dry while others continue drying. When you close the door again, press the START/PAUSE button in order to resume drying. (When the door is opened the START/PAUSE light

will flash Amber, after the door is closed and the START/PAUSE button pressed, the START/PAUSE light will stop flashing and show green.) Note: During all of the Heat & Enjoy programme and the Post Care phase this light flashes Amber.

9. When the programme is complete. The buzzer will sound. Open the door, take the laundry out, clean the filter and replace it. Empty the water container and replace it (see Maintenance). If the Crease Care option has been selected and you do not remove the laundry immediately, the dryer will tumble occasionally for 10 hours or until you open the door.

10. Unplug the dryer.

+ 14 hidden pages