Hotpoint SX 1038L P 0 X Instruction booklet

Please phone us on
08448 24 24 24
to activate your
guarantee
SX 1038L P 0 X
English

Operating Instructions

Contents
Operating Instructions,1 Warnings,2 Description of the appliance,3 Description of the appliance,3 Installation,4 Electrical Connection,4 Start-up and use,6 Modes,7 Precautions and tips,11 Maintenance and care,11 Troubleshooting,13 After Sales Service,15 Guarantee,16
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Warnings

GB
WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.
Never use steam cleaners or pressure cleaners on the appliance.
WARNING: Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock.
Before initiating the automatic cleaning cycle:
• clean the oven door;
• remove large or coarse food residues from the
inside of the oven using a damp sponge. Do not use
detergents;
• remove all accessories and the sliding rack kit (where present);
• do not place tea towels
Keep children away from the appliance during the automatic cleaning cycle as surfaces may become very hot.
! When you place the rack inside, make sure that the stop is directed upwards and in the back of the cavity.
2
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Description of the appliance

7
1
3
4
5
1011121315
1437
6
5
9
16
2
14
17
Overall view
9 6
GB
1. POSITION 1
2. POSITION 2
3. POSITION 3
4. POSITION 4
5. POSITION 5
6. GUIDES for the sliding racks
7. DRIPPING PAN
8. GRILL
9. Control panel

Description of the appliance

Control panel
1. MANUAL COOKING MODE Icons
2. FAST CLEAN selector
3. TEMPERATURE display
4. TEMPERATURE icon
5. DURATION icon
6. TIME display
7. END OF COOKING Icon
8. CONTROL PANEL LOCK icon
9. START / STOP
10. LIGHT icon
11. CLOCK icon
12. MINUTE MINDER Icon
13. TIME / TEMPERATURE ADJUSTMENT Icons
14. PREHEATING / RESIDUAL HEAT icons
15. DOOR LOCK indicator
16. AUTOMATIC/ECO COOKING MODE icons
17. CONTROL PANEL POWER BUTTON
8
2
8
3
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Installation

590 mm.
595 mm.
22,5 mm.*
20,5 mm.
550 mm.
570 mm.
20 mm.
575-585 mm.
45 mm.
560 mm.
550 mm.
min.
GB
! Please keep this instruction booklet in a safe place for future reference. If the appliance is sold, given away or moved, please make sure the booklet is
also passed on to the new owners so that they may benet from the advice
contained within it.
! Please read this instruction manual carefully: it contains important information concerning the safe operation, installation and maintenance of the appliance.
Positioning
! Do not let children play with the packaging material; it should be disposed
of in accordance with local separated waste collection standards (see Precautions and tips).
! The appliance must be installed by a qualied professional in accordance
with the instructions provided. Incorrect installation may damage property or cause harm to people or animals.
Built-in appliances
Use an appropriate cabinet to ensure that the appliance operates properly:
• the panels adjacent to the oven must be made of heat-resistant material.
• cabinets with a veneer exterior must be assembled with glues which can
withstand temperatures of up to 100°C.
• to install the oven under the counter (see diagram) or in a kitchen unit,
the cabinet must have the following dimensions:
Centring and xing
Secure the appliance to the cabinet:
• open the oven door.
• slide out the side gaskets at the top until the 2 xing holes are exposed;
• x the oven to the cabinet using the 2 wood screws.
• reposition the 2 gaskets.
! All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool.

Electrical Connection

The electrical connection to the mains must be made on the appliance. The power voltage and frequency are as indicated on the rating plate.
! THIS APPLIANCE MUST BE EARTHED.
! The appliance must not come into contact with electrical parts once it has
been installed. The indications for consumption given on the data plate have been calculated for this type of installation.
Ventilation
To ensure adequate ventilation, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of
wood, or on a completely at surface with an opening of at least 45 x 560
mm (see diagrams).
45 mm.
560 mm.
Fitting the power supply cable
1. Open the terminal board by inserting a screwdriver into the side tabs of the cover. Use the screwdriver as a lever by pushing it down to open the cover (see diagram).
2. Install the power supply cable by loosening the cable clamp screw and the three wire contact screws
N
N
L-N- . Connect the wires to the corresponding terminals: the Blue wire to the terminal marked (N), the Brown wire to the terminal marked (L) and the Yellow/Green wire to
L
L
3. Secure the cable by fastening the clamp screw.
4. Close the cover of the terminal board.
the terminal marked
(see diagram).
Electrical Connection:
Voltage Frequency: see data plate Fuse Section: 16A Supply cable: 3x1.5mm
2
You can connect your oven to the system means of a terminal board. Refer to above information for the minimal cable sections and the calibration of the protective elements according to the connection. If the appliance is installed with a junction box, an omnipolar circuit breaker
- with a minimum contact opening of 3mm - should be installed between the appliance and the mains.
4
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Power cable supply connection to the electrical mains:
* Only for models with drawn rails ** Only for models with wire rails
We recommend you use a power supply cable which is long enough to allow you to take the oven out of its recess in the event of maintenance operations
(only use HAR - H 05 - RRF quality cables tted with a plug conforming to
the regulations in force. The plug must be accessible at all times.
Unplug the appliance before all operations, even when replacing the oven lamp. Using the appliance without correct earthing is highly dangerous.
! After connecting the appliance to the exible cable, tighten all the screws
on the terminal board.
APPLIANCE SPECIFICATIONS
width 43.5 cm
Dimensions*
Volume*
Dimensions**
Volume**
Electrical connections
ENERGY LABEL and ECODESIGN
height 32,4 cm depth 41.5 cm
59 l
width 45.5 cm height 32,4 cm depth 41.5 cm
62 l
voltage: 230-240V~ 50/60Hz or 50Hz (see data plate) maximum power absorbed 2800-3000 W
EU Directive no 65/2014 supplementing Directive 2010/30/EU. EU Regulation no 66/2014 implementing Directive 2009/125/EC. Standard EN 60350-1 Standard EN 50564
GB
Declared energy consumption for Forced convection Class – heating mode: ECO.
This appliance conforms to the following European Economic Community directives:
- 2006/95/EC of 12/12/06 (Low Voltage) and subsequent amendments;
- 2004/108/EC of 15/12/04 (Electromagnetic Compatibility) and subsequent amendments;
- 93/68/EEC of 22/07/93 and subsequent amendments.
- 2002/96/EU and subsequent amendments.
- 1275/2008 standby/off mode.
.
.
5
Loading...
+ 11 hidden pages