Hotpoint SX 1038L CX, SX 1038N CX User Manual

Operating Instructions
Please phone us on
08448 24 24 24
to activate your
guarantee
OVEN
GB
English,1
SX 1038N CX SX 1038L CX
Contents
Installation, 2-3
Positioning Electrical connection Data plate
Description of the appliance, 4
Overall view Control panel
Start-up and use, 5-6
Control panel lock Setting the clock Setting the minute minder Starting the oven Concealed handle Restoring the factory settings Standby
Modes, 7-10
Manual cooking modes Automatic cooking modes Programming cooking Practical cooking advice Cooking advice table
GB
Precautions and tips, 11
General safety Disposal Respecting and conserving the environment
Care and maintenance, 12-13
Switching the appliance off Cleaning the appliance Cleaning the oven door Replacing the light bulb Assembling the sliding rack kit
Troubleshooting, 14
After Sales Service, 15
Guarantee, 16
560 mm.
45 mm.
Installation
GB
! Please keep this instruction booklet in a safe place for future reference. If the appliance is sold, given away or moved, please make sure the booklet is also passed on to the new owners so that they may benefit from the advice contained within it.
! Please read this instruction manual carefully: it contains important information concerning the safe operation, installation and maintenance of the appliance.
Positioning
! Do not let children play with the packaging material; it should be disposed of in accordance with local separated waste collection standards (
Precautions and tips
).
! The appliance must be installed by a qualified professional in accordance with the instructions provided. Incorrect installation may damage property or cause harm to people or animals.
Built-in appliances
Use an appropriate cabinet to ensure that the appliance operates properly:
• The panels adjacent to the oven must be made of heat-resistant material.
• Cabinets with a veneer exterior must be assembled with glues which can withstand temperatures of up to 100°C.
• To install the oven under the counter (
diagram
) or in a kitchen unit, the cabinet must
have the following dimensions:
see
see
Ventilation
To ensure adequate ventilation is provided, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of wood, or on a completely flat surface with an opening of at least 45 x 560 mm (
see diagrams
).
Centring and fixing
Secure the appliance to the cabinet:
• Open the oven door.
• Remove the 2 rubber plugs covering the fixing holes on the perimeter frame.
• Fix the oven to the cabinet using the 2 wood screws.
• Replace the rubber plugs.
! All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool.
590 mm.
595 mm.
20 mm.
570 mm.
550 mm.
20,5 mm.
22,5 mm.*
550 mm.
min.
45 mm.
560 mm.
575-585 mm.
* Stainless steel models only
! The appliance must not come into contact with electrical parts once it has been installed. The indications for consumption given on the data plate have been calculated for this type of installation.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
2
Electrical connection
42 NL
The electrical connection to the mains must be made on the appliance. The power voltage and frequency are as indicated on the rating plate.
THIS APPLIANCE MUST BE EARTHED.THIS APPLIANCE MUST BE EARTHED.
!
THIS APPLIANCE MUST BE EARTHED.
THIS APPLIANCE MUST BE EARTHED.THIS APPLIANCE MUST BE EARTHED.
Connecting the power supply cable
Power cable supply connection to the electrical mains:
We recommend you use a power supply cable which is long enough to allow you to take the oven out of its recess in the event of maintenance operations (only use HAR - H 05 - RRF quality cables fitted with a plug conforming to the regulations in force. The plug must be accessible at all times.
GB
To open the terminal board:
• Using a screwdriver, press on the tabs situated on each side of the terminal board cover.
• Pull open the terminal board cover.
To connect the power supply cable, proceed as follows:
••
• Unscrew the cable clamp screw and the contact
•• screws L-N-.
• Fasten the wires beneath the screwheads using the following colour scheme: Blue (N) Brown (L)
Yellow-Green
• Fasten the power supply cable in the corresponding cable clamp and close the cover.
Electrical Connection:
Voltage Frequency: 230 V-1+N 50Hz Fuse Section: 16A Supply cable: 3x1.5mm
2
Unplug the appliance before all operations, even when replacing the oven lamp.
Using the appliance without correct earthing is highly dangerous.
! After connecting the appliance to the flexible cable, tighten all the screws on the terminal board.
APPLIANCE SPECIFICATIONS
Dimensions
Volume
Electrical connections
width 43.5 cm height 32 cm depth 41.5 cm
58 l
voltage: 230 - 240 V~ 50/60 Hz (see data plate) maximum power absorbed 2800-3000 W
Directive 2002/40/EC on the label of electric ovens. Standard EN 50304
ENERGY LABEL*
Declared energy consumption for Forced convection Class – heating mode: ECO.
You can connect your oven to the system means of a terminal board. Refer to above information for the minimal cable sections and the calibration of the protective elements according to the connection. If the appliance is installed with a junction box, an omnipolar circuit breaker - with a minimum contact opening of 3mm - should be installed between the appliance and the mains.
* Without removable guide rails
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
3
Description of the appliance
GB
Overall view
Control panel
Control panel
GRILL
DRIPPING PAN
GUIDES for the
sliding racks
position 5
position 4 position 3 position 2 position 1
COOKING MODE
MANUAL
icons
CONTROL PANEL POWER BUTTON
AUTOMATIC/
COOKING MODE
ECO
icons
TEMPERATURE
display
PREHEATING /
RESIDUAL HEAT
icons
TEMPERATURE
icon
TIME /
TEMPERATURE
ADJUSTMENT
icons
MINUTE MINDER
DURATION
icon
icon
TIME
display
CLOCK
icon
END OF COOKING
icon
CONTROL PANEL LOCK
icon
LIGHT
icon
START / STOP
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
4
Start-up and use
! The first time you use your appliance, heat the empty oven with its door closed at its maximum temperature for at least half an hour. Make sure that the room is well ventilated before switching the oven off and opening the oven door. The appliance may emit a slightly unpleasant odour caused by protective substances used during the manufacturing process burning away. ! To make the setting process easier, press and hold the + and numbers on the display rapidly. ! Each setting will automatically be stored in the appliance memory after 10 seconds. ! The touch controls cannot be activated if the user is wearing gloves.
Some models are equipped with a system of hinges which allows the door to close slowly, without the user having to follow the movement through with his/ her hand. To use the system correctly, before closing the door:
• Open the door fully.
• Do not force the closing movement manually.
––
– buttons to scroll through the
––
Control panel lock
! The control panel can be locked while the oven is off, once cooking has started or finished and during programming.
To lock the oven controls, press and hold the button for at least 2 seconds. A buzzer will sound and the TEMPERATURE display shows the key symbol “O—n”. The icon will light up to indicate lock activation. To deactivate the lock, press and hold the button again for at least 2 seconds.
Setting the clock
! The clock can only be set when the oven is switched off. If the oven is in standby mode,
pressing the time setting. Press it again to set the time.
After connection to the power supply network or after
a blackout, the TIME display will flash for 10 seconds. To set the clock:
1. Press the
2. Adjust the hour figure using the + and - buttons.
3. Once you have reached the correct hour value,
button once will display the current
button and the digits on the
button.
indicates that the clock has not been set correctly.
Setting the minute minder
! The minute minder may be set regardless of whether the oven is switched on or off. It does not switch the oven on or off.
When the set time has elapsed, the timer emits a buzzer that will automatically stop after 30 seconds or when any active button on the control panel is pressed. To adjust the timer proceed as follows:
1. Press button
2. Set the desired time using buttons
3. Once you have reached the desired value, press
the
The lit minder is on.
To cancel the minute minder, press the and use the + and – buttons to set the time to 00:00.
Press button
The minder has been disabled.
button again.
symbol will remind you that the minute
icon will switch off to indicate that the minute
.
+ and -.
button
again.
Starting the oven
1. Switch the control panel on by pressing the button. The appliance buzzer sounds three times (ascending) and all buttons light up in sequence.
2. Press the button corresponding to the desired cooking mode. The TEMPERATURE display shows:
- the temperature associated with the mode, if programming manually;
- “Auto”, if programming is automatic. The TIME display shows:
- the current time, if programming manually;
- the duration, if programming is automatic.
3. Press the
4. The oven will begin its preheating phase, the preheating indicators will light up as the temperature rises.
5. When the preheating process has finished, a buzzer sounds and all the preheating indicator lights show that this stage has been completed: the food can then be placed in the oven.
6. During cooking it is always possible to:
button to begin cooking.
GB
press the
4. Repeat the above process to set the minutes.
If a blackout occurs, it will be necessary to reset the
clock. If the
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
button.
icon flashes on the display, this
- change the temperature by pressing the
button, followed by the + and - buttons (
modes only
);
manual
5
Loading...
+ 11 hidden pages