Hotpoint SH83CK, SH83CZ, SH83K, SH83X Operating Instructions Manual

Operating Instructions

Contents

Installation, 2

Positioning

Electrical connection, 3

Data plate

Description of the appliance, 4

Overall view
Control panel

Start-up and use, 5

Starting the oven

The electronic cooking programmer, 6

Cooking modes, 7-9

Cooking modes
Practical cooking advice
Cooking advice table

Precautions and tips, 10

General safety
Disposal
Respecting and conserving the environment
Recycling & Disposal Information

Maintenance and care, 11

Switching the appliance off
Cleaning the appliance
Cleaning the oven door
Replacing the light bulb
Sliding Rack Kit assembly

After Sales Service, 12

Guarantee, 13

OVEN

SE861X/1
SH83CK
SH83CZ
SH83K
SH83X

English,1

GB

GB

2

GB

595 mm.

595 mm.

24 mm.

545 mm.

5 mm.

567 mm.

23 mm.

593 mm.

45 mm.

558 mm.

547 mm. min.

Installation

560 mm.

45 mm.

! Before placing your new appliance into operation
please read these operating instructions carefully.
They contain important information for safe use, for
installation and for care of the appliance.

! Please keep these operating instructions for future
reference. Pass them on to possible new owners of
the appliance.

Positioning

! Keep packaging material out of the reach of
children. It can become a choking or suffocation
hazard.

see Precautions and tips

).

! The appliance must be installed by a qualified
person in compliance with the instructions provided.
Incorrect installation may cause harm to persons,
animals or may damage property.

Fitting the appliance

Use the appropriate cabinet to ensure that the
appliance functions properly.

• The panels adjacent to the oven must be made of
heat-resistant material.

• Cabinets with a veneer exterior must be assembled
with glues which can withstand temperatures of up
to 100°C.

• To install the oven under the counter (

see diagram

)
and in a kitchen unit, the cabinet must have the
following dimensions:

! The appliance must not come into contact with
electrical parts once it has been installed.
The consumption indications on the data plate have
been calculated for this type of installation.

Ventilation

To ensure good ventilation, the back panel of the
cabinet must be removed. It is advisable to install the
oven so that it rests on two strips of wood, or on a
completely flat surface with an opening of at least 45 x
560 mm (

see diagrams

).

Centring and fastening

Position the 4 tabs on the side of the oven according
to the 4 holes of the outer frame. Adjust the tabs
according to the thickness of the cabinet side panel,
as shown below:

thickness of 20 mm: take off
the removable part of the tab
(

see diagram

)

thickness of 18 mm: use the
first groove, which has already
been set in the factory (

see

diagram

)

thickness of 16 mm: use the
second groove (

see diagram

)

Secure the appliance to the cabinet by opening the
oven door and putting 4 screws into the 4 holes of the
outer frame.

! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a
tool.

3

GB

DATA P LATE

Dimensions

width cm 37.5
heigh t cm 32
depth cm 41.5

Vol ume lt. 50

Ele ctr ic al
connections

volt age: 230 -240V ~ 50Hz
maximum p ower absorbed
2800W-3000W

ENE RGY LAB EL

Directive 2002/40/EC on the label
of electri c ovens.
Stand ard EN 50 304

Energy consumption f or Natural
convec ti on – heatin g mode:
Convection mode.

Decl ared energy consumpti on for
For ced co nvection Clas s – heat ing
mode: Baking.

This appliance conforms to the
following European Econ omic
Community directives:

- 20 06/95/EEC of 12/12/06 (Low
Volt age) and subsequent
amendments;

- 20 04/108/ EEC of 15/12/04
(El ec tromagn etic C ompatib ility) an d
subsequent amendment s;

- 93 /68/EEC of 2 2/07/93 and
subsequent amendment s.

- 20 02/96/EC and subsequent
amendments.

Electrical Connection

Electrical connection

The electrical connection to the mains must be made
on the appliance. The power voltage and frequency
are as indicated on the rating plate.

!

THIS APPLIANCE MUST BE EARTHED.THIS APPLIANCE MUST BE EARTHED.

THIS APPLIANCE MUST BE EARTHED.THIS APPLIANCE MUST BE EARTHED.

THIS APPLIANCE MUST BE EARTHED.

Connecting the power supply cable

To open the terminal board:

• Using a screwdriver, press on the tabs situated on
each side of the terminal board cover.

• Pull open the terminal board cover.

To connect the power supply cable, proceed as
follows:

••

••

• Unscrew the cable clamp screw and the contact
screws L-N-6.

• Fasten the wires beneath the screwheads using the
following colour scheme: Blue (N) Brown (L)

Yellow-Green

6

• Fasten the power supply cable in the
corresponding cable clamp and close the cover.

Electrical Connection:

Voltage Frequency: 230
V-1+N 50Hz
Fuse Section: 16A
Supply cable: 3x1.5mm

2

You can connect your oven to the system means of a
terminal board. Refer to above information for the
minimal cable sections and the calibration of the
protective elements according to the connection.
If the appliance is installed with a junction box, an
omnipolar circuit breaker - with a minimum contact
opening of 3mm - should be installed between the
appliance and the mains.

Power cable supply connection to the electrical
mains:

We recommend you use a power supply cable which
is long enough to allow you to take the oven out of its
recess in the event of maintenance operations (only
use HAR - H 05 - RRF quality cables fitted with a plug
conforming to the regulations in force.

The plug must be accessible at all times.

Unplug the appliance before all operations, even
when replacing the oven lamp.

Using the appliance without correct earthing is
highly dangerous.

! After connecting the appliance to the flexible
cable, tighten all the screws on the terminal board.

42
NL

4

GB

Control panelControl panel

Control panelControl panel

Control panel

GRILLGRILL

GRILLGRILL

GRILL

DRIPPING PANDRIPPING PAN

DRIPPING PANDRIPPING PAN

DRIPPING PAN

GUIDES GUIDES

GUIDES GUIDES

GUIDES for the
sliding racks

position 5position 5

position 5position 5

position 5

position 4position 4

position 4position 4

position 4

position 3position 3

position 3position 3

position 3

position 2position 2

position 2position 2

position 2

position 1position 1

position 1position 1

position 1

Description of the appliance

Overall view

Control panel

•• ••

SELECTORSELECTOR

SELECTORSELECTOR

SELECTOR

Knob

Indicator light

THERMOSTATTHERMOSTAT

THERMOSTATTHERMOSTAT

THERMOSTAT

ELECTRONIC

programmer

THERMOSTATTHERMOSTAT

THERMOSTATTHERMOSTAT

THERMOSTAT

Knob

5

GB

Start-up and use

! The first time you use your appliance, heat the

empty oven with its door closed at its maximum
temperature for at least half an hour. Ensure that the
room is well ventilated before switching the oven off
and opening the oven door. The appliance may
produce a slightly unpleasant odour caused by the
burning away of protective substances used during
the manufacturing process.

Starting the oven

1. Select the desired cooking mode by turning the

SELECTOR knob.

2. Select the desired temperature with the

THERMOSTAT knob. See the Cooking advice table for
cooking modes and the suggested cooking
temperatures (

see Cooking Modes

).

3. When lit, the THERMOSTAT indicator light indicates

that the oven is heating up to the temperature set.

4. You may do the following during cooking:

- change the cooking mode by turning the SELECTOR

knob.

- change the temperature by turning the

THERMOSTAT knob.

- stop cooking by turning the SELECTOR knob to the

“0” position.

! Never put objects directly on the oven bottom to
avoid damaging the enamel coating.

! Always place cookware on the rack(s) provided.

Cooling ventilation

In order to cool down the external temperature of the
oven, some models are fitted with a cooling fan that
blows out air between the control panel and the oven
door.
! Once the cooking has been completed, the cooling
fan remains on until the oven has cooled down
sufficiently.

Oven light

It goes on when selecting

with the SELECTOR

knob. It stays on when a cooking mode is selected.