Hotpoint SE481012GX, SE48L1012GX, SE48R1012GX User Manual

Operating Instructions
OVEN
GB
English, 1
SE481012X SE48L1012X SE48R1012X SE481012GX SE48L1012GX SE48R1012GX
Contents
GB
Installation, 2-3
Electrical connection, 4
Data plate
Description of the appliance, 5
Overall view of classical-opening model Overall view of side-opening model Control panel
Start-up and use, 6-7
Control panel lock DEMO mode Setting the clock Setting the timer Starting the oven
Cooking modes, 8-11
Manual cooking modes Automatic cooking modes Programming cooking Practical cooking advice Cooking advice table
Precautions and tips, 12
General safety Disposal Respecting and conserving the environment
Care and maintenance, 13-14
Switching the appliance off Cleaning the appliance Cleaning the oven door Replacing the light bulb Assembling the sliding rack kit Assistance
After Sales Service, 15
Repair Service and Information Desk Extended Warranties Genuine Parts and Accessories
Guarantee, 16
560 m
m
.
45 mm.
Installation
GB
Before operating your new appliance please read this instruction booklet carefully. It contains important information concerning the safe operation, installation and maintenance of the appliance.
Please keep these operating instructions for future reference. Make sure that the instructions are kept with the appliance if it is sold, given away or moved.
Positioning
Keep all packaging materials out of the reach of children. It may present a choking or suffocation hazard (see Precautions and tips).
The appliance must be installed by a qualified person in compliance with the instructions provided. Incorrect installation may cause harm to people and animals or may damage property.
Built-in appliance
Use the appropriate cabinet to ensure that the appliance functions properly.
 The panels adjacent to the oven must be made of
heat-resistant material.
OK OK
If the appliance is fitted under the counter, make sure that the hob piping is positioned correctly and that it does not interfere with the oven during installation or obstruct the rear vents of the cooling fan.
The appliance must not come into contact with electrical parts once it has been installed. The indications for consumption given on the data plate have been calculated for this type of installation.
Ventilation
To ensure adequate ventilation is provided, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of wood, or on a completely flat surface with an opening of at least 45 x 560 mm (see diagrams).
 Cabinets with a veneer exterior must be
assembled with glues which can withstand temperatures of up to 100°C.
 To install the oven under a counter (see diagram)
or in a kitchen unit, the cabinet must have the following dimensions:
in.
. m
m
547 m
45 mm.
558 mm.
475 mm.
480 mm.
595 m
24,5 mm.
7 mm.
470 mm.
3 mm.
m
.
545 mm.
Centring and fixing
Position the 4 tabs on the side of the oven so that they are lined up with the 4 holes on the outer frame. Adjust the tabs according to the thickness of the cabinet side panel, as shown below:
20 mm thick: take off the removable part of the tab (see diagram).
18 mm thick: use the first groove, which has already been set in the factory (see diagram).
2
16 mm thick: use the second groove (see diagram).
Secure the appliance to the cabinet by opening the oven door and inserting 4 screws into the 4 holes on the outer frame.
All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool.
GB
3
Electrical Connection
GB
Electrical connection
The electrical connection to the mains must be made on the appliance. The power voltage and frequency are as indicated on the rating plate.
! THIS APPLIANCE MUST BE EARTHED.
Connecting the power supply cable
To open the terminal board:
 Using a screwdriver, press on the tabs situated
on each side of the terminal board cover.
 Pull open the terminal board cover.
To connect the power supply cable, proceed as follows:
_ Unscrew the cable clamp screw and the contact
screws L-N-$.
 Fasten the wires beneath the screwheads using
the following colour scheme: Blue (N) Brown (L)
Yellow-Green$
 Fasten the power supply cable in the
corresponding cable clamp and close the cover.
Electrical Connection:
Voltage Frequency: 230 V-1+N 50Hz Fuse Section: 16A Supply cable: 3x1.5mm
2
42 NL
You can connect your oven to the system means of a terminal board. Refer to above information for the minimal cable sections and the calibration of the protective elements according to the connection. If the appliance is installed with a junction box, an omnipolar circuit breaker - with a minimum contact opening of 3mm - should be installed between the appliance and the mains.
Power cable supply connection to the elec trical mains:
We recommend you use a power supply cable which is long enough to allow you to take the oven out of its recess in the event of maintenance operations (only use HAR - H 05 - RRF quality cables fitted with a plug conforming to the regulations in force.
The plug must be accessible at all times.
Unplug the appliance before all operations, even when replacing the oven lamp.
Using the appliance without correct earthing is highly dangerous.
! After connecting the appliance to the flexible cable, tighten all th board.
TABLE OF CHARACTERISTICS
Dimensions *
Volume *
Electrical connections
ENERGY LABEL *
* Without removable guide rails
e screws on the terminal
width 43.5 cm height 32 cm depth 41.5 cm 58 l voltage: 220-240V ~ 50/60Hz maximum power absorbed 2800 W Directive 2002/40/EC on the label of electric ovens. Regulation EN 50304
Declared energy consumption for Forced convection Class  heating mode: Gratin This appliance conforms to the following European Economic Community directives: 2006/95/EEC dated 12/12/06 (Low Voltage) and subsequent amendments - 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequent amendments ­93/68/EEC dated 22/07/93 and subsequent amendments. 2002/96/EEC
4
Description of the appliance
Overall view of classical-opening model
GRILL rack
DRIPPING PAN rack
Control panel
Overall view of side-opening model
GUIDE RAILS
for the sliding racks
GB
GUIDE RAILS
for the sliding racks
position 5
position 4 position 3 position 2 position 1
GRILL
rack
position 5 position 4 position 3 position 2 position 1
Control panel
CONTROL PANEL
POWER
button
TEMPERATURE
adjustment
COOKING MODE
MANUAL
COOKING
MODE
selector
AUTOMATIC
selector
DRIPPING PAN
MANUAL
COOKING
MODE
icons
AUTOMATIC
COOKING
MODE
icons
rack
TEMPERATURE
display
DURATION
icon
TIMER
icon
COOKING END TIME
icon
TIME
display
START
icon
CLOCK
icon
Control panel
LIGHT
button
TIME SETTING
button
START / STOP
TIME ADJUSTMENT
buttons
5
Loading...
+ 11 hidden pages