Hotpoint SE1002X User Manual

Instructions for Installation and Use

Electric Oven

Models: SE1002X

To the Installer

Before installation fill in the product details on the back cover of this book.

The information can be found on the rating plate.

To the User

You must read the instructions prior to installing and using the appliance and

then retain them for future reference.

Operating Instructions

OVEN

Retention of this Instruction Book

This Instruction Book must be kept handy for

reference as it contains important details on the safe

and proper use of the appliance.

If you sell or pass the appliance to someone else, or

move house and leave it behind, make sure this Book

is also provided so the new owner can become

familiar with the appliance and safety warnings.

If the Book is lost or damaged a copy may be

obtained from:

Merloni Elettrodomestici LTD., Morley Way,

Peterborough, PE2 9JB

Contents

Introduction, 3

Installation, 4

Positioning

Electrical connection, 5

Data plate

Description of the appliance, 6

Overall view

Control panel

Start-up and use, 7

Setting the clock and timer

Starting the oven

Control Panel Lock

DEMO mode

Cooking modes, 8-10

Cooking modes

Programming your cooking

Practical cooking advice

Cooking advice table

Precautions and tips, 11

General safety

Disposal

Respecting and conserving the environment

Maintenance and care, 12

Switching the appliance off

Cleaning the appliance

Cleaning the oven door

Replacing the light bulb

Sliding Rack Kit assembly, 13

After Sales Service, 14

Hotpoint Guarantee, 15

Key Contacts, Back Cover

Introduction

Your new electric oven is guaranteed* and will give

lasting service. This guarantee is only applicable if

the appliance has been installed in accordance with

the installation instructions detailed in this booklet.

To help make best use of your cooking equipment,

please read this booklet carefully.

The oven is designed specifically for domestic use

and responsibility will not be accepted for use in any

other installation.

! When the oven is first used, an odour may be

omitted - this will cease after a short period of use.

To help remove the 'new' smell, heat the empty oven

to maximum temperature for a minimum of two to three

hours, keeping the door/s closed. Ensure that the

room is well ventilated (eg. open a window or use an

extractor fan) and that persons who may be sensitive

to the odour avoid any fumes. It is suggested that any

pets be removed from the room until the smell has

ceased.

This odour is due to any temporary finish on oven

linings and elements and any moisture absorbed by

the insulation.

! The guarantee is subject to the provisions that

the appliance:

(a) Has been used solely in accordance with this

booklet.

(b) Has been properly connected to a suitable

supply voltage as stated on the rating plate,

attached to the appliance.

or been modified or repaired by any person

other than the manufacturers authorised

employee or agent.

(d) Has been correctly installed.

Installation

! Before placing your new appliance into operation

please read these operating instructions carefully.

They contain important information for safe use, for

installation and for care of the appliance.

! Please keep these operating instructions for future

reference. Pass them on to possible new owners of

the appliance.

Positioning

! Keep packaging material out of the reach of children. It can become a choking or suffocation

hazard. (see Precautions and tips).

! The appliance must be installed by a qualified

person in compliance with the instructions provided.

Incorrect installation may cause harm to persons,

animals or may damage property.

Fitting the appliance

Use the appropriate cabinet to ensure that the

appliance functions properly.

 The panels adjacent to the oven must be made of

heat-resistant material.

Ventilation

To ensure good ventilation, the back panel of the

cabinet must be removed. It is advisable to install the

oven so that it rests on two strips of wood, or on a

completely flat surface with an opening of at least 45 x

560 mm (see diagrams).

45 mm.

560 mm.

Centring and fastening

Position the 4 tabs on the side of the oven according

to the 4 holes of the outer frame. Adjust the tabs

according to the thickness of the cabinet side panel,

as shown below:

thickness of 20 mm: take off

the removable part of the tab

(see diagram)

 Cabinets with a veneer exterior must be assembled

with glues which can withstand temperatures of up

to 100°C.

 To install the oven under the counter (see

diagram) and in a kitchen unit, the cabinet must

have the following dimensions:

567 mm.

45 mm.

558 mm.

593 mm.

23 mm.

595 mm.

5 mm.

595 mm.

545 mm.

24 mm.

! The appliance must not come into contact with

electrical parts once it has been installed.

The consumption indications on the data plate have

been calculated for this type of installation.

thickness of 18 mm: use the

first groove, which has already

been set in the factory (see

diagram)

thickness of 16 mm: use the

second groove (see diagram)

Secure the appliance to the cabinet by opening the

oven door and putting 4 screws into the 4 holes of the

outer frame.

! All parts which ensure the safe operation of the

appliance must not be removable without the aid of a

tool.

Electrical Connection

Electrical connection

The electrical connection to the mains must be made

on the appliance. The power voltage and frequency

are as indicated on the rating plate.

! THIS APPLIANCE MUST BE EARTHED.

Connecting the power supply cable

To open the terminal board:

 Using a screwdriver, press on the tabs situated on

each side of the terminal board cover.

 Pull open the terminal board cover.

To connect the power supply cable, proceed as

follows:

 Unscrew the cable clamp screw and the contact

screws L-N-6.

 Fasten the wires beneath the screwheads using the

following colour scheme: Blue (N) Brown (L)

Yellow-Green 6

 Fasten the power supply cable in the

corresponding cable clamp and close the cover.

Power cable supply connection to the electrical

mains:

We recommend you use a power supply cable which

is long enough to allow you to take the oven out of its

recess in the event of maintenance operations (only

use HAR - H 05 - RRF quality cables fitted with a plug

conforming to the regulations in force.

The plug must be accessible at all times.

Unplug the appliance before all operations, even

when replacing the oven lamp.

Using the appliance without correct earthing is

highly dangerous.

! After connecting the appliance to the flexible

cable, tighten all the screws on the terminal board.

DATA PLATE

width cm 37.5

Dimensions

height cm 32 depth cm 41.5

Electrical Connection:

Voltage Frequency: 230

V-1+N 50Hz

Fuse Section: 16A

Supply cable: 3x1.5mm

4 2

N L

You can connect your oven to the system means of a

terminal board. Refer to above information for the

minimal cable sections and the calibration of the

protective elements according to the connection.

If the appliance is installed with a junction box, an

omnipolar circuit breaker - with a minimum contact

opening of 3mm - should be installed between the

appliance and the mains.

Volume

Electrical connections

ENERGY LABEL

Control programs in accordance with standard IEC456

lt. 50 voltage: 230-240V ~ 50Hz /

maximum power absorbed 2800W-3000W

Directive 2002/40/EC on the label of electric ovens. Standard EN 50304

Energy consumption for Natural convection – heating mode: Convection mode

Declared energy consumption for Forced convection Class – heating mode: Baking

This appliance conforms to the following European Economic Community directives: 73/23/EEC of 19/02/73 (Low Voltage) and subsequent amendments;

-89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent amendments; 93/68/EEC of 22/07/93 and subsequent amendments.

+ 11 hidden pages