Hotpoint RLS80, RLM80, RLA80 User Manual
LARDER FRIDGE - MODEL RLA80, RLM80, RLS80
INSTRUCTIONS FOR INSTALLATION & USE
GETTING STARTED:
To ensure that your fridge runs reliably and efficiently follow these steps.
STEP 1
Choose a location for
your fridge, away from
any heat sources and
allow adequate
ventilation - 100mm
(4 inches) gap above.
STEP 3
To prevent the fridge
tilting forwards it must be
held in place with the
stability bracket supplied.
NB.This is the responsibility of
the customer.
STEP 5
After the front feet have
been adjusted and the
fridge is level, fit the left
and right hand bottom
hinge covers supplied.
Align with the cover plate
slots and push into
position.
STEP 2
STEP 4
Move the fridge into
position, using the sides
of the cabinet. Take care
to avoid damaging the
refrigerant circuit pipe
work on the rear.
Level the fridge by
adjusting the front feet.
This will stop rocking or
vibration and keep the
door aligned.
NB.The spanner is for illustration
only and is not supplied with the
fridge.
STEP 6
Before plugging in and
switching on, leave the
fridge in its final
location for at least 15
minutes to allow it to
settle.
INSTALLATION CONTROLS
SAFETY &
USEFUL ADVICE
MAINTENANCE
CLEANING &
TROUBLESHOOTING
STEP 7
Plug in and switch on.
Allow the fridge to cool
before placing food
inside.
All food in the fridge
should be covered.
STEP 8
Your fridge is now
working.
If after 24 hours your
fridge is not operating as
you want, refer to the
TROUBLESHOOTING
section.
Read the rest of these instructions to get the best from your appliance
and remember to fill in your guarantee registration.
Keep this Book in a safe place for quick reference.
GUARANTEE
SERVICE &
For Your Safety
For your safety, read the following advice:
The fridge cooling system contains a small amount of gas which is environmentally
friendly but flammable. To avoid any risk :-
● Install the fridge following the installation instructions and ensure
that ventilation openings are kept clear of obstruction.
● Take care when installing or moving the fridge to avoid damaging
the pipes on the rear.
● If you suspect a leak, do not switch on the fridge,but open the
windows and doors to ventilate the room.
● Do not use any mechanical or electrical devices inside the fridge, for
SAFETY &
INSTALLATION
● Only use this fridge for storing domestic foodstuffs.
When installing your fridge :-
● The stability bracket must be installed securely,in accordance to the
● Ensure that the mains cable is not trapped underneath or behind the fridge
● Do not stack any other appliance on top of this fridge as they may
instance for manual defrosting,they may cause damage.
instructions, before using the fridge. This is the responsibility of the
customer.
when you install or move it.
damage the fridge or become unstable.
When using your fridge :-
● Do not sit or stand on top of your fridge.
● Do not store poisonous, flammable or dangerous substances in your fridge.
● Do not use aerosol sprays for defrosting or cleaning your fridge.
If you sell the fridge, pass on this booklet to the new owner.
2
Installation
Location & Air Circulation
100mm
(4 inches)
Locate your fridge away from sources of heat e.g. cookers,
radiators,direct sunlight as extreme temperature will
affect its performance.
Allow a minimum 100mm (4 inches) between the top of
the fridge and the ceiling or the underside of a wall
cupboard.
Providing you follow the recommended ventilation
requirements you will :-
● Prolong the life of the fridge.
● Minimise the risk of condensation on the outside of
the fridge.
● Minimise the running costs.
● Minimise operating sounds caused by vibration.
Minimum space required to open door
The fridge needs a space of 600mm (24 inches) in front to allow the door to open.
When positioning the fridge next to a unit, a gap of 30mm (1
1
/4inch) can be left
at the hinge side of the door to allow the easy removal of furniture.If preferred
the fridge can be positioned so that a gap is not left.This will restrict how far the
door can be opened but the furniture can still be removed (see diagrams below).
The door hinge side can be changed to make it easier to open (see ‘Door Reversal’
in the CLEANING & MAINTENANCE section).
INSTALLATION
SAFETY &
600mm
TOP VIEW
30mm or more
TOP VIEW
600mm
less than 30mm
3
Installation
Stability bracket:
WARNING:To prevent the fridge from tilting forwards, it must be held in place
with the stability bracket supplied. This is the responsibility of the customer.
Fixed to the floor or wall at the rear of the
fridge, the stability bracket hooks onto the
compressor mounting plate holding the
fridge secure.
SAFETY &
INSTALLATION
Note: The fridge is heavy so care must be taken when moving it.
1. Position the fridge in its chosen
location.
2. Looking from the front of the fridge,
mark the position of the left hand
panel.
3. Move the fridge far enough away to
get clear access to the back wall.
4. In order to clear components on the
compressor mounting plate,the
stability bracket must be positioned
on the floor between 100 - 200mm
to the right of the left hand panel
mark.
5. Mark and drill the fixing holes and insert suitable fixings to hold the bracket firm.
6. Carefully re-position the fridge. Make sure that the compressor mounting plate
locates into the stability bracket.
The stability bracket must be installed
securely in accordance with these
instructions BEFORE using the fridge.
position stability bracket
100 - 200mm away from
left hand panel mark.
4
Installation
Levelling:
Level the fridge when it is in its final location by adjusting the front feet,until firm
contact is made with the floor. This will stop rocking or vibration and keep the door
aligned which helps the fridge run reliably and efficiently.
Note: Before plugging in and switching on,leave the fridge standing
in its final location for at least 15 minutes to allow it to settle.
Hinge Covers:
After the front feet have been adjusted and the fridge is level fit the left and right
hand bottom hinge covers supplied.
To fit:
Align the bottom hinge cover onto the
cover plate slots.
Push until the bottom hinge cover
clicks into place.
INSTALLATION
SAFETY &
5
Installation
Electrical Supply
WARNING:This appliance must be earthed.
The appliance must be positioned so that the plug is accessible after
installation.
Fuses
Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the
fuse, only use those rated at 13A and ASTA approved to BS1362.
SAFETY &
Changing the Plug
INSTALLATION
Cut off and dispose of the supplied plug if it does not fit your socket.
WARNING:To avoid a shock hazard do not insert the discarded plug into a socket
anywhere else.
IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE :
Green/Yellow - Earth
Blue - Neutral Brown - Live
If you change the plug, the colour of wires in the mains lead may not correspond with
the colour of the markings identifying terminals in the plug. You should therefore
wire it as shown above.
Changing the Mains Lead
This appliance is fitted with a special mains lead. If you need to replace the mains
lead due to damage one can be bought from Hotpoint Service (see KEY CONTACTS,
back page). It is strongly advised that this work is carried out by a qualified
electrician.
CE Marking certifies that this appliance conforms to the following EEC
directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC
6
Loading...