Hotpoint RLM56, RLA54, RLA56, RLM54, RLM64 User Manual
LARDER FRIDGE - MODELS RLA54, RLA56, RLA64, RLM54, RLM56, RLM64
INSTRUCTIONS FOR INSTALLATION & USE
GETTING STARTED:
To ensure that your fridge runs reliably and efficiently follow these steps.
STEP 1 STEP 2
Choose a location for your
fridge, away from any
heat sources and
allow adequate
ventilation - 30mm
1
/4 inch) gap above.
(1
STEP 3
Level the fridge by
adjusting the front feet.
This will stop rocking or
vibration and keep the
NB.The spanner is for illustration
only and is not supplied with the
door aligned.
STEP 5
fridge.
STEP 4
STEP 6
Move the fridge into
position, using the sides
of the cabinet. Take care
to avoid damaging the
refrigerant circuit pipe
work on the rear.
Before plugging in and
switching on, leave the
fridge in its final
location for at least 15
minutes to allow it to
settle.
INSTALLATION CONTROLS
SAFETY &
USEFUL ADVICE
MAINTENANCE
CLEANING &
TROUBLESHOOTING
Plug in and switch on.
Allow the fridge to cool
before placing food
inside.
All food in the fridge
should be covered.
Your fridge is now
working.
If after 24 hours your
fridge is not operating as
you want, refer to the
Troubleshooting section.
Read the rest of these instructions to get the best from your appliance
and remember to fill in your guarantee registration.
Keep this Book in a safe place for quick reference.
GUARANTEE
SERVICE &
For Your Safety
For your safety, read the following advice:
The fridge cooling system contains a small amount of gas which is environmentally
friendly but flammable. To avoid any risk :-
● Install the fridge following the installation instructions and ensure
that ventilation openings are kept clear of obstruction.
● Take care when installing or moving the fridge to avoid damaging
the pipes on the rear.
● If you suspect a leak, do not switch on the fridge,but open the
windows and doors to ventilate the room.
● Do not use any mechanical or electrical devices inside the fridge, for
SAFETY &
INSTALLATION
● Only use this fridge for storing domestic foodstuffs.
When installing your fridge :-
● Ensure that the mains cable is not trapped underneath or behind the fridge
● Do not stack any other appliance on top of this fridge as they may
When using your fridge :-
instance for manual defrosting.
when you install or move it.
damage the fridge or become unstable.
● Do not sit or stand on top of your fridge.
● Do not store poisonous, flammable or dangerous substances in your fridge.
● Do not use aerosol sprays for defrosting or cleaning your fridge.
If you sell the fridge, pass on this booklet to the new owner.
2
Installation
Location & Air Circulation
100mm
(4 inches)
Locate your fridge away from sources of heat e.g. cookers,
radiators,direct sunlight as extreme temperature will
affect its performance.
Allow a minimum 100mm (4 inches) between the top of
the fridge and the ceiling or the underside of a wall
cupboard.
Providing you follow the recommended ventilation
requirements you will :-
● Prolong the life of the fridge.
● Minimise the risk of condensation on the outside of
the fridge.
● Minimise the running costs.
● Minimise operating sounds caused by vibration.
Minimum space required to open door
The fridge needs a space of 600mm (24 inches) in front to allow the door to open.
When positioning the fridge next to a unit, a gap of 30mm (1
1
/4inch) can be left
at the hinge side of the door to allow the easy removal of furniture.If preferred
the fridge can be positioned so that a gap is not left.This will restrict how far the
door can be opened but the furniture can still be removed (see diagram below).
The door hinge side can be changed to make it easier to open (see ‘Door Reversal’
in the CLEANING & MAINTENANCE section).
INSTALLATION
SAFETY &
600mm
TOP VIEW
30mm or more
TOP VIEW
600mm
less than 30mm
3
Installation
Levelling:
Level the fridge when it is in its final location by adjusting the front feet,until firm
contact is made with the floor. This will stop rocking or vibration and keep the door
aligned which helps the fridge run reliably and efficiently.
Note: Before plugging in and switching on,leave the fridge standing
in its final location for at least 15 minutes to allow it to settle.
Bottle Retainer:
To fit the bottle rack retainer:
SAFETY &
INSTALLATION
Locate the retainer groove at one end of
the bottle rack and then gradually press
down along the top edge until the
retainer is fully in the home position.
Joining:
Equal height Hotpoint fridges and freezers can be joined together to look like one
unit by using a Filler Kit available from Hotpoint Genuine Parts & Accessories Mail
Order Hotline (see KEY CONTACTS,back page).
4
Installation
Electrical Supply
WARNING:This appliance must be earthed.
The fridge must be positioned so that the plug is accessible after
installation.
Fuses
Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the
fuse, only use those rated at 13A and ASTA approved to BS1362.
Changing the Plug
Cut off and dispose of the supplied plug if it does not fit your socket.
WARNING:To avoid a shock hazard do not insert the discarded plug into a socket
anywhere else.
IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE :
Green/Yellow - Earth
INSTALLATION
SAFETY &
Blue - Neutral Brown - Live
If you change the plug, the colour of wires in the mains lead may not correspond with
the colour of the markings identifying terminals in the plug. You should therefore
wire it as shown above.
Changing the Mains Lead
This fridge is fitted with a special mains lead. If you need to replace the mains lead
due to damage, one can be bought from Hotpoint Service (see KEY CONTACTS, back
page). It is strongly advised that this work is carried out by a qualified electrician.
CE Marking certifies that this appliance conforms to the following EEC
directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC
5
Controls
Controlling the Temperature of the Fridge Compartment
The control wheel on the front of the worktop adjusts the internal fridge
compartment temperature. The internal temperature should be 5˚C or colder
although some sections, such as the salad bin, will be slightly warmer.
The setting of the control wheel will depend on the location of the fridge,the room
temperature and how often the door is opened. The normal set point (marked by a 3
and N on the dial) is usually suitable. If you need to adjust the temperature turn the
control wheel:
Clockwise (higher number) - Colder
Anti-clockwise (lower number) - Warmer
Temperature Indicator
(not applicable to all models)
CONTROLS
After plugging in and switching on PLEASE WAIT 24 HOURS for the refrigerator
compartment temperature to stabilise.After this time the indicator should clearly
show OK and that indicates the refrigerator compartment is operating at the correct
temperature.
If the indicator is completely black, the compartment temperature is too high and
you should adjust the temperature wheel to a colder setting (see above).
If you have to adjust the temperature setting please WAIT A MINIMUM OF 10 HOURS,
this is time for the temperature to stabilise before checking that the indicator is
showing OK.
If large quantities of food have been added or if the refrigerator door has been
opened frequently it is normal for the temperature indicator not to show OK.WAIT A
MINIMUM OF 10 HOURS before adjusting the temperature setting to a colder
position.
You can check the temperature of the fridge compartment by using a Fridge Freezer
Thermometer available from Hotpoint Genuine Parts and Accessories Mail Order
Hotline (see KEY CONTACTS back page).
WARNING: Do not use a mercury filled thermometer,as breakage would cause a
health hazard.
Your fridge must NOT be placed in a room where the temperature goes below 6˚C or
above 38˚C for prolonged periods,as the internal fridge temperature will not be
maintained.
6
The temperature indicator is located on the bottom right
hand side of the refrigerator wall.
This indicator shows when the refrigerator compartment of
your larder fridge is operating at the correct temperature.
Loading...