Hotpoint RLA32, RLA30, RLM30, RLS30 User Manual

LARDER FRIDGE - MODELS RLA30, RLM30, RLS30, RLA32

INSTRUCTIONS FOR INSTALLATION & USE

GETTING STARTED:

To ensure that your fridge runs reliably and efficiently follow these steps.

STEP 1 STEP 2

Choose a location for your

fridge, away from any

heat sources and

allow adequate

ventilation - 30mm

1

/4 inch) gap above.

(1

STEP 3 STEP 4

Level the fridge by
adjusting the front feet.
This will stop rocking or

vibration and keep the

door aligned.

STEP 5 STEP 6

Move the fridge into
position, using the sides
of the cabinet. Take care
to avoid damaging the
refrigerant circuit pipe
work on the rear.

Before plugging in and
switching on, leave the
fridge in its final
location for at least 15
minutes to allow it to
settle.

INSTALLATION CONTROLS

SAFETY &

USEFUL ADVICE

MAINTENANCE

CLEANING &

TROUBLESHOOTING

Plug in and switch on.

Allow the fridge to cool

before placing food

inside.

All food in the fridge

should be covered.

Your fridge is now
working.
If after 24 hours your
fridge is not operating as
you want, refer to the
Troubleshooting section.

Read the rest of these instructions to get the best from your appliance

and remember to fill in your guarantee registration.

Keep this Book in a safe place for quick reference.

GUARANTEE

SERVICE &

For Your Safety

For your safety, read the following advice:

The fridge cooling system contains a small amount of gas which is environmentally
friendly but flammable. To avoid any risk :-

● Install the fridge following the installation instructions and ensure
that ventilation openings are kept clear of obstruction.

● Take care when installing or moving the fridge to avoid damaging
the pipes on the rear.

● If you suspect a leak, do not switch on the fridge,but open the
windows and doors to ventilate the room.

● Do not use any mechanical or electrical devices inside the fridge, for

SAFETY &

INSTALLATION

● Only use this fridge for storing domestic foodstuffs.

When installing your fridge :-

● Ensure that the mains cable is not trapped underneath or behind the fridge

● Do not stack any other appliance on top of this fridge as they may

When using your fridge :-

instance for manual defrosting.

when you install or move it.

damage the fridge or become unstable.

● Do not sit or stand on top of your fridge.

● Do not store poisonous, flammable or dangerous substances in your fridge.

● Do not use aerosol sprays for defrosting or cleaning your fridge.

If you sell the fridge, pass on this booklet to the new owner.

2

Installation

Location & Air Circulation

30mm (11/4 inch)

Locate your fridge away from sources of heat e.g.
cookers, radiators, direct sunlight as extreme temperature
will affect its performance.

Allow a minimum 30mm (11/4

inch) between the top of

the fridge and the underside of the worktop.

Providing you follow the recommended ventilation requirements you will :-

● Prolong the life of the fridge.

● Minimise the risk of condensation on the outside of the fridge.

● Minimise the running costs.

● Minimise operating sounds caused by vibration.

Minimum space required to open door

The fridge needs a space of 600mm (24 inches) in front to allow the door to open.
When positioning the fridge next to a unit, a gap of 30mm (1

1

/4inch) can be left
at the hinge side of the door to allow the easy removal of furniture.If preferred
the fridge can be positioned so that a gap is not left.This will restrict how far the
door can be opened but the furniture can still be removed (see diagram below).
The door hinge side can be changed to make it easier to open (see ‘Door Reversal’
in the CLEANING & MAINTENANCE section).

INSTALLATION

SAFETY &

600mm

TOP VIEW

30mm or more

TOP VIEW

600mm

less than 30mm

3

Installation

Levelling:

Level the fridge when it is in its final location by adjusting the front feet,until firm
contact is made with the floor. This will stop rocking or vibration and keep the door
aligned which helps the fridge run reliably and efficiently.

Before plugging in and switching on, leave the fridge standing in its final location for
at least 15 minutes to allow it to settle.

Fitting a Fridge under a Work Top

To minimise running costs Hotpoint recommend fitting a vent to the rear of your

SAFETY &

worktop,which is available from Hotpoint Genuine Parts & Accessories Mail Order

INSTALLATION

Hotline (see KEY CONTACTS,back page).

WARNING:If there is less than 30mm clearance above the fridge,a vent must be
fitted to provide adequate ventilation above your fridge.

4

Installation

Electrical Supply

WARNING:This appliance must be earthed.

The fridge must be positioned so that the plug is accessible after
installation.

Fuses

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the
fuse, only use those rated at 13A and ASTA approved to BS1362.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING:To avoid a shock hazard do not insert the discarded plug into a socket
anywhere else.

IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE :

Green/Yellow - Earth

INSTALLATION

SAFETY &

Blue - Neutral Brown - Live

If you change the plug, the colour of wires in the mains lead may not correspond with
the colour of the markings identifying terminals in the plug. You should therefore
wire it as shown above.

Changing the Mains Lead

This fridge is fitted with a special mains lead. If you need to replace the mains lead
due to damage or require a longer lead,one can be bought from Hotpoint Service
(see KEY CONTACTS,back page). It is strongly advised that this work is carried out by
a qualified electrician.

CE Marking certifies that this appliance conforms to the following EEC
directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC

5