Hotpoint Re963013 Owner's Manual

Height

3" Min.

Width

Depth

BUIL T-IN TRIM KIT INSTALLA TION INSTRUCTION

FOR KENMORE TRIM-KIT MODEL - 30” : 63002, 63004, 63009, 64003

27” : 63012, 63014, 63019, 63013

■

FOR USE WITH KENMORE MICROWAVE OVEN MODEL:

721.62462200, 721.62463200, 721.62464200, 721.62469200

■

UL LISTED - FOR USE OVER KENMORE 30”,27” ELECTRIC BUILT-IN OVENS
(INCLUDING MODELS - 30” : 41785, 41789, 41085, 41086, 41089, 49002, 49003, 49004, 49009

27” : 47489, 47485, 47486, 47189)

PARTS LIST

• Trim Kit

• Bottom Duct (1)

•

Upper Duct (1)

•

Anti-Tip
Bracket (1)

• Installation

instruction (1)

•

1” Screws

(4 Req’d 2 Extra)

1

•

/2” Screws

(11 Req’d 2 Extra)

•

Bottom Bracket (1)

• Side Duct (1)

•

Template (1)

CUTOUT DIMENSIONS

27” 30”

Height 16

Width
Depth
(min.) (22

1

25

/2” 25 1/2” (min.), 28 1/2” (max.)

21

“ with flush mount receptacle.

3

/4” if non-flush receptacle is

used)

3

/4”

- 1 -

P/NO.: 3828W5U0189

1

/2" Screws (2)

Front

Rear

1

/2" Screws (2)

1

/2" Screws (2)

Upper Duct

3 tabs

Side Duct

3 Holes

"a)"

"b)"

Existing

Screw (1)

STEP 1

1. Disconnect the microwave oven from the
outlet before proceeding with installation.

2. Remove any loose items (turntable, support,
etc) from the microwave oven.

3. Fasten the bottom bracket to the bottom duct
by using two

1

/2” screws.

4. Install bottom duct with four

1

/2” screws as

shown.

FRONT VIEW OF

MICROWAVE

STEP 2

1. Remove the one existing screw from the left side of the microwave oven.

2. Connect the side duct to upper duct as shown.

a) Insert projecting tabs of upper duct into holes of side duct.
b) Bend tabs up as shown.
NOTE: Remove any oil or dirt on surface of microwave oven before ducts are attached.

3. Peel off the backing of double sided tape.
Attach the side duct and upper duct assembly
on the microwave cabinet. Press down firmly
on ducts. Fasten duct assembly to left side of
cabinet with one existing screw.

- 2 -

Bottom Duct

Anti-Tip
Bracket

Bottom Bracket

1

/2" Screw

Anti-Tip Assembly

Positioning
Flange

Cutout
Opening

1

/2" Screw

A

B

C

Cutout Floor

Center Line

Anti-Tip Bracket

1

/2" Screws (2)

STEP 3

1. On the cutout floor, mark hole centers for the
anti-tip brackets as shown using the supplied
template. Be sure to align the center line of
template to center line of cutout floor.

2. Drill two holes for anti-tip bracket.

7

(use

/64” drill or #35 drill)

3. Install anti-tip bracket onto cutout floor using

1

two

/2” screws.

DIMENSIONS:

A = 4

1

/4”

B = 3”

C = 18

3

/16”

STEP 4

1. Slide microwave oven part way into cabinet
opening.
(Bottom brackets must be flat to the cutout
floor to engage correctly with anti-tip
brackets as shown)

2. Plug in the microwave oven.

3. Center the microwave oven within the
cut-out opening and slide the microwave
oven in the anti-tip bracket.
(Ensure the microwave oven is accurately

centered)

4. Drill pilot holes (use
through the positioning flange and then

install three
bottom duct as shown.

7

/64” drill or #35 drill)

1

/2” screws at the front of the

- 3 -