Instructions for use
|
WASHER |
-DRYER |
|
|
|
|
|
|
|
|
|
|
|
|
! This symbol reminds you to read this instruc- |
|
|||
GB |
||||
tion manual. |
|
|||
|
GB
English,1
RD 1076 J
Contents
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 6
Cutting off the water or electricity supply
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 7
General safety
Disposal
Opening the porthole door manually
Description of the washer-dryer, 8-9
Control panel Display
How to run a wash cycle or a drying cycle, 10
Wash cycles and functions, 11
Table of wash cycles Wash functions
Detergents and laundry, 12
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 13-14
Product Guarantee and Repair Information, 15
1
Installation
! Keep this instruction manual in a safe place GB for future reference. Should the appliance be
sold, transferred or moved, make sure the instruction manual accompanies the washerdryer to inform the new owner as to its operation and features.
! Read these instructions carefully: they contain vital information on installation, use and safety.
Unpacking and levelling
Unpacking |
!This is a separate part of the polystyrene base and should be removed with the base.
!IMPORTANT check when unpacking your machine.
1. Unpack the washer-
dryer.
2. Check whether
the washer-dryer has been damaged during transport. If this is the
case, do not install
it and contact your
retailer.
3. Remove the 4 protective screws and the rubber bush with the respective spacer, situated on the rear of the appliance (see also the installation leaflet).
4.Seal the gaps using the plastic plugs provided.
5.Keep all the parts: you will need them again if the washer-dryer needs to be moved to another location.
! Packaging materials are not children’s toys.
Levelling
Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly.
1. Install the washerdryer on a flat sturdy floor, without resting it up against walls, cabinets or anything else.
2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2°.
Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washer-dryer.
Electric and water connections
Connecting the water inlet hose
1. Connect the supply pipe by screwing it to a cold water tap using a 3/4 gas threaded connection (see
figure).
Before performing the connection, allow the water to run freely until it is perfectly clear.
2. Connect the other end of the water inlet hose to the washerdryer,
screwing it onto the appliance’s cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure).
3. Make sure there are no kinks or bends in the hose.
!The water pressure at the tap must be within the values indicated in the Technical details table (on the page 5).
!If the water inlet hose is not long enough, contact a specialist store or an authorised serviceman.
!Ensure that the supply taps are allowing water through. Old taps may seize in the closed position and thus prevent water reaching the machine.
!Never use second-hand or old inlet hoses; use the products supplied with the machine.
2
Connecting the drain hose
65 - 100 cm |
Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;
Where it connects to the waste water pipe cut end off spigot or remove the blanking cap
The drain hose may be connected to an under-sink trap. Before connecting the drain hose from the machine ensure that any blanks or
removable ends have been taken off the spigot.
If it is placed over the edge of a basin or sink be sure the free end of the hose should not be underwater.
! We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.
Ensure that if the drain hose is pushed into a standpipe, that the end does not go down
more than 15cms (6 inches). If the hose is pushed down too far, this may cause the machine to self -syphon ie. continuously empty as it is filling.
Electric connection
Before plugging the appliance into the mains socket, make sure that:
•the socket is earthed and in compliance with the applicable law;
•the socket is able to sustain the appliance’s maximum power load indicated on the Technical Data Plate fixed on the machine;
|
|
|
|
|
• the supply voltage is included within the |
|
|||
GB |
||||
values indicated on the Technical Data Plate |
||||
|
||||
fixed on the machine. |
|
|||
|
||||
• the socket is compatible with the washer- |
|
|||
dryer’s plug. If this is not the case, replace |
|
|||
the socket or the plug. |
|
|||
Your appliance is now supplied with a 13 amp |
|
|||
fused plug it can be plugged into a 13 amp |
|
|||
socket for immediate use. Before using the |
|
|||
appliance please read the instructions below. |
|
|||
WARNING - THIS APPLIANCE MUST BE |
|
|||
EARTHED. |
|
|
|
|
THE FOLLOWING OPERATIONS SHOULD |
|
|||
BE CARRIED OUT BY A QUALIFIED ELECTRI- |
|
|||
CIAN. |
|
|
|
|
Replacing the fuse: |
|
|
|
|
When replacing a faulty fuse, a 13 amp ASTA |
|
|||
approved fuse to BS 1362 should always be |
|
|||
used, and the fuse cover re-fitted. If the fuse |
|
|||
cover is lost, the plug must not be used until a |
|
|||
replacement is obtained. |
|
|||
Replacement fuse covers: |
|
|||
If a replacement fuse cover is fitted, it must be |
|
|||
of the correct colour as indicated by the colou- |
|
|||
red marking or the colour that is embossed in |
|
|||
words on the base of the plug. Replacements |
|
|||
can be obtained directly from your nearest |
|
|||
Service Depot. |
|
|
|
|
Removing the plug: |
|
|
|
|
If your appliance has a non-rewireable moul- |
|
|||
ded plug and you should wish to re-route the |
|
|||
mains cable through partitions, units etc., |
|
|||
please ensure that either: |
|
|||
the plug is replaced by a fused 13 ampere |
|
|||
rewireable plug bearing the BSI mark of ap- |
|
|||
proval. |
|
|
|
|
or: |
|
|
|
|
the mains cable is wired directly into a 13 |
|
|||
amp cable outlet, controlled by a switch, (in |
|
|||
compliance with BS 5733) which is accessible |
|
|||
without moving the appliance. |
|
|||
Disposing of the plug: |
|
|||
Ensure that before disposing of the plug itself, |
|
|||
you make the pins unusable so that it cannot |
|
|||
be accidentally inserted into a socket. |
|
|||
Instructions for connecting cable to an alternati- |
|
|||
ve plug: |
|
|
|
|
Important: the wires in the mains lead are co- |
|
|||
loured in accordance with the following code: |
|
|||
Green & Yellow |
Earth |
|
||
Blue |
Neutral |
|
||
Brown |
Live |
|
3
As the colours of the wires in the lead may not GB correspond with the coloured markings iden-
tifying the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E or or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked L or coloured Red.
Connect Blue wire to terminal marked N or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse, either in the plug or adaptor or at the distribution board.
If you are in any doubt regarding the electrical supply to your machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with the following code:
BLUE |
|
NEUTRAL (N) |
BROWN |
|
LIVE (L) |
GREEN & YELLOW |
EARTH (E) |
|
|
|
|
GREEN & |
|
|
YELLOW |
|
|
BROWN |
13 ampere fuse |
|
|
|
|
BLUE |
CROSS-BAR |
|
|
CORD GRIP |
|
|
|
|
! The power supply cable must only be replaced by an authorised serviceman.
Warning! The company denies all liability if and when these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, using wash cycle number auto clean (see “Cleaning the washer-dryer”).
Disposing of the appliance:
When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described on the previous page.
!The washer-dryer should not be installed in an outdoor environment, not even where the area is sheltered, because it may be very dangerous to leave it exposed to damp, rain and thunderstorms.
!When the washer-dryer is installed, the mains socket must be within easy reach.
!Do not use extensions or multiple sockets.
!The power supply cable must never be bent or dangerously compressed.
4
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Technical data |
|
GB |
|||
Model |
RD 1076 J |
|
|
||
|
|
|
|
||
|
width 59.5 cm |
|
|||
Dimensions |
height 85 cm |
|
|||
|
depth 60,5 cm |
|
|
||
|
from 1 to 10 kg for the wash |
|
|||
Capacity |
programme |
|
|||
from 1 to 7 kg for the drying |
|
||||
|
|
||||
|
programme |
|
|
||
Electrical |
please refer to the technical |
|
|||
connections |
data plate fixed to the machine |
|
|
||
|
maximum pressure |
|
|||
Water con- |
1 MPa (10 bar) |
|
|||
minimum pressure |
|
||||
nections |
|
||||
0.05 MPa (0.5 bar) |
|
||||
|
|
||||
|
drum capacity 71 litres |
|
|||
Spin speed |
up to 1600 rotations per |
|
|||
minute |
|
|
|||
|
|
||||
|
Wash: programme 8; tem- |
|
|||
|
perature 60°C; using a load |
|
|||
|
of 10 kg. |
|
|||
Energy |
Drying: the greater load |
|
|||
(7kg) must be dried by se- |
|
||||
rated |
|
||||
lecting the “EXTRA” dryness |
|
||||
programmes |
|
||||
level. |
|
||||
according to |
The remainder of the load |
|
|||
regulation |
must be dried by selecting |
|
|||
EN 50229 |
|
||||
the “EXTRA” dryness level: |
|
||||
|
|
||||
|
the load must consist of 3 |
|
|||
|
sheets, 2 pillowcases and |
|
|||
|
1 hand towel. |
|
This appliance conforms to the following EC Directives:
-2004/108/EC (Electromagnetic Compatibility)
-2006/95/EC (Low Voltage)
- 2012/19/EU (WEEE)
5