Starting the appliance
Using the display
Chiller system
Ever Fresh
Using the refrigerator to its full potential
Using the freezer to its full potential
Maintenance and care, 10
Switching the appliance off
Cleaning the appliance
Ever Fresh
Avoiding mould and unpleasant odours
Replacing the light bulb
Changing the odour filter
Precautions and tips, 11
General safety
Disposal
Respecting and conserving the environment
Troubleshooting, 12
Assistance, 13
1
Installation
GB
! Before operating your new appliance please read
these instructions carefully. They contain important
information for safe use, installation and care of the
appliance.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free
room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation
to operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part
of the appliance and any furniture above it, and at
least 5 cm between the sides and any furniture/side
walls.
4. Ensure the appliance is away from any sources of heat
(direct sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers
supplied in the installation kit, following the
instructions provided.
Levelling
1. Install the appliance on a level and sturdy floor.
2. If the floor is not perfectly horizontal, adjust the
refrigerator by tightening or loosening the front feet.
Electrical connections
After transportation of the appliance, carefully place it
in an upright position and wait at least 3 hours before
connecting it to the electricity mains. Before inserting
the plug into the electrical socket ensure the following:
The appliance is earthed and the plug is compliant
with the law.
The socket can withstand the maximum power of the
appliance (this is indicated on the data plate in the
bottom left section of the refrigerator compartment),
for example 150 W).
The voltage is in the range of values indicated on
the data plate located on the bottom left section
(e.g. 220-240V).
The socket is compatible with the plug of the
appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it (see Assistance).
Do not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only (see Assistance).
! The manufacturer declines any liability should
these safety measures not be observed.
Reversible doors
If it is necessary to change the direction in which the
doors open, please contact the Technical Assistance
Centre.
2
Description of the
appliance
Control panel
REFRIGERATOR
Display
REFRIGERATOR
Temperature
Adjustment
FREEZER
Temperature
Adjustment
FREEZER
Display
ON/OFF
ON/OFF
It is possible to switch the whole product (both the
refrigerator and freezer compartments) on by pressing
this button. The red LED indicates that the product is
switched off, while the green LED shows that it is
operating. To switch the product off, press and hold the
ON/OFF button for at least two seconds.
I CARE
This is used to activate and deactivate the I Care
function (the optimal temperature for energy saving
levels). When activated, the AUTO LED and the I Care
LED illuminate simultaneously.
ALARMS
This controls all the alarm signals connected to product
operation.
Child Lock
Enables the buttons on the control panel to be locked in
order to avoid various functions being activated accidentally
by children. To enable the Child Lock function, the ALARM
button must be pressed for 2 seconds.
REFRIGERATOR + and - Temperature Adjustment
Enable the temperature setting of the refrigerator to be
modified, with the relative confirmation of the
temperature selected shown on the display.
GB
ALARMS
SUPER COOL
SUPER FREEZE
EVER FRESH
ICE PARTY
HOLIDAY
I CARE
FREEZER Display
Shows the set temperature relating to the freezer
compartment.
SUPER COOL
Activates or deactivates the SUPER COOL function (rapid
cooling). The refrigerator display shows the text SC).
SUPER FREEZE
Activates or deactivates the SUPER FREEZE function
(rapid freezing), The freezer display shows the text SF).
EVER FRESH
Activates or deactivates the Ever Fresh function. When
the LED is illuminated, the vacuum-packing system is
operating; when the LED switches off the operation is
complete and the container airtight. A red LED signals
that a problem has been encountered.
HOLIDAY
Activates or deactivates the HOLIDAY function (the
AUTO LED and HOLIDAY LED illuminates).
ICE PARTY
Activates or deactivates the ICE PARTY function (It
reduces the temperature of the freezer for the period of
time required to cool a bottle.).
FREEZER + and - Temperature Adjustment
Enable the temperature setting of the freezer to be
modified, with the relative confirmation of the
temperature selected shown on the display.
REFRIGERATOR Display
Indicates the set temperature relating to the refrigerator
compartment or shows that it has been deactivated (in
this case the display shows - -).
3
Description of the appliance
GB
Overall view
LAMP
(see Maintenance)
SHELVES
WINE RACK
EVER FRESH
shelf
FRUIT and
VEGETABLE
compartment
Removable
multipurpose
*
SHELVES
BOTTLE shelf
ICE TRAYS Ice Care
FREEZER and
STORAGE
compartment
ICE TRAYS Ice Care
STORAGE
compartments
Levelling FEET
Removable
multipurpose
SHELVES
Varies by number and/or position.
Available only on certain models.
*
4
Accessories
Refrigerator compartment
SHELVES: the shelves are removable and their height
may be adjusted thanks to special rails, allowing easy
storage of large containers and bulky food.
EVER FRESH: shelf dedicated
to storing food in vacuumpacked containers. Food
keeps for longer when stored in
the containers provided.
ODOUR FILTER
models are fitted with a new
active carbon odour filter,
which ensures better air quality
inside the refrigerator.
The filter is located on the
bottom left side, inside the
FRUIT and VEGETABLE
compartment
: some
*
Freezer compartment
GB
ICE PARTY: ensures bottles of
sparkling wine or champagne
reach the right temperature.
Place the bottle in the bucket
provided inside the FREEZER
and STORAGE compartment.
The bucket may be used to
serve the bottle and keeps it
cool outside the appliance.
ICE CARE tray
The fact that they are situated on the top part of the
freezer drawers ensures greater cleanliness: the ice no
longer comes into contact with the food placed inside
the freezer compartment; furthermore, the dripping of
the water during filling is avoided (a lid to cover up the
hole after filling with water is also provided).
1. Pull out the tray by pushing it up.
Check that the tray is ompletely empty and fill it with
water through the opening provided.
2. Take care not to exceed the level indicated (MAX
WATER LEVEL). Excess water prevents the ice
cubes from dispensing (if this happens, wait for the
ice to melt and empty the tray).
3. Turn the tray 90°: due to the connected
compartments each mould fills with water (seediagram).
4. Close the opening with the lid provided and put the
tray back.
5. When the ice has formed (minimum time
approximately 8 hours) knock the tray against a hard
surface and wet the outside so that the ice cubes
come loose and take them out through the opening.
Available only in certain models.
*
WATER LEVEL
MAX
WATER LEVEL
MAX
MAX
WATER LEVEL
5
Start-up and use
GB
Starting the appliance
! After transportation of the appliance, carefully place it in
an upright position and wait at least 3 hours before
connecting it to the electricity mains, to make sure it
operates as it should.
Clean the inside of the refrigerator well using warm
water and bicarbonate of soda before placing food
inside it.
The appliance comes with a motor protection control
system which makes the compressor start
approximately 8 minutes after being switched on.
The compressor also starts each time the power
supply is cut off whether voluntarily or involuntarily
(blackout).
Freezer Compartment
When the product is switched on (the ON/OFF button is
pressed for more than two seconds) the freezer
compartment is set to its default value of -18°C. We
recommend that the SUPER FREEZE function is set (the
freezer display shows the text SF) in order to accelerate
the cooling process of the compartment; when the inside
of the compartment has reached its optimal temperature
the function will be deactivated and the food may be
placed inside.
Refrigerator Compartment
When the appliance is switched on the refrigerator
compartment is set to its default value of +5°C. We
recommend that the SUPER COOL function is set (the
refrigerator display shows the text SC) in order to
accelerate the cooling process of the compartment. After
a few hours it will be cool enough for food to be placed
inside.
Navigating the display
Setting the temperatures:
If the product is switched on, the refrigerator and freezer
displays will indicate the temperatures set at that
moment. To change them, simply press the + and buttons corresponding to the compartment for which you
wish to change the set temperature. To be specific, each
time one of the buttons is pressed the temperature is
increased or decreased by 1°, and the number of
illuminated horizontal bars is adjusted accordingly. The
temperature values that may be selected for the
refrigerator compartment are +8°C, +7°C, +6°C, +5°C,
+4°C, +3°C and +2°C, while the values that may be set
for the freezer are -18°C, -19°C, -120°C, -21°C, -22°C, 24°C and -26°C.
The temperatures are automatically set to +5°C for the
refrigerator compartment and -18°C for the freezer
compartment (these are standard food storage values).
When the I Care function is active, the appliance
automatically adjusts the temperatures according to the
conditions inside and outside the refrigerator; the
operation of this function is signalled by the text AUTO.
Whenever it is necessary to activate the I Care function
at temperatures that are different to the standard storage
values, the I Care button must be pressed as soon as
the function is activated and held down while the new
temperatures are set using the + and - buttons. Under
these conditions, the temperatures may be set to 4°C,
5°C and 6°C for the refrigerator compartment and -18°C,
-19°C and -20°C for the freezer compartment.
When the HOLIDAY function is active the temperature
may not be adjusted, however the appliance adjusts itself
automatically so that the optimal settings for the situation
are used: +12°C for the refrigerator compartment and -18°C for the freezer compartment. This function is
indicated by the text.
To activate and deactivate the functions simply press the
relevant button and the function status will be signalled
by the corresponding LED switching on or off.
Several functions (SUPER COOL, SUPER FREEZE, ICEPARTY, I CARE) are incompatible with others
(HOLIDAY,...); remember that there is a pre-set order of
priority which will help you to use the product in the best
possible way.
When the Ice Party function has finished, press the ICEPARTY button to stop the relevant LED from flashing. This
flashing indicates that the function is complete and that the
bottle should be removed from the freezer compartment.
Child Lock
To enable the Child Lock function, the ALARM button
must be pressed for 2 seconds; the button lock activation
is confirmed by a short beep and the text LO CH
appears on the refrigerator and freezer displays. This text
is then replaced by the refrigerator and freezer
temperatures set prior to when the child lock function was
enabled.
To deactivate the function, press the ALARM button or 2
seconds; deactivation will be confirmed by a short beep
and the text CH OF will appear on the refrigerator and
freezer displays for 1 second.
6
Chiller system
No Frost
The No Frost system
circulates cold air
continuously to collect
humidity and prevent ice
and frost formation. The
system maintains an
optimal humidity level in
the compartment,
preserving the original
quality of the food,
preventing the food from sticking together and making
defrosting a thing of the past.
Do not block the aeration cells by placing food or
containers in direct contact with the refrigerating back
panel. Close bottles and wrap food tightly.
Ever Fresh
The absence of air inside the containers ensures that
food is preserved for longer periods of time while
maintaining its original appearance, taste and
nutritional characteristics.
In
normal
conditions
Food
General cooked dish2 days10 days
Ready-made rice or pasta dish 2 days10 days
Fresh fish2-3 days4-5 days
Fresh raw meat3 days9 days
Hard cheese15 days60 days
Raw vegetables5 days21 days
Fresh fruit10 days21 days
Dry biscuits180 days 365 days
Pastries with cream/custard2 days10 days
Other desserts/pastries5 days20 days
* The above table is indicative and refers to food
storage in the refrigerator at temperatures ranging
between 3°C and 5°C. The length of time food lasts for
will, however, depend on the initial freshness of the
products, preparation and storage methods, and
correct use of the Ever Fresh function.
! The foods tendency to spoil and use-by date must
always be borne in mind when using the Ever Fresh
food storage system. This method of storing food does
not change any of the characteristics of the food.
! Use only the containers that come with the product to
store food in the Ever Fresh system. Do not use any
other type of container.
With
EVER
FRESH*
Ever Fresh system
The Ever Fresh system is activated and deactivated
by means of a button on the refrigerator shelf, an
external button on the display and a knob on the cover
of each container.
! There is a pump in the centre of the Ever Fresh shelf
which sucks the air out of the containers.
Activating and deactivating Ever Fresh
1. Fill the container. Make sure that the food inside
leaves room for the container to be closed properly.
2. Put the lid on the container.
U
U
C
M
A
V
O
T
O
U
A
V
3. Close the handles on either
side of the container and turn
the knob on the lid of the
container all the way to the
CLOSE position. Then turn the
O
T
N
R
E
E
P
P
A
O
C
H
C
I
L
U
O
S
S
O
E
knob anticlockwise to the
VACUUM position
(see figure A).
B
4. Press the button on the shelf
and place the container in the
1
central position (see figure B).
5. Lock the container into
2
position by pulling the button
on the shelf (see figure C).
C
6. Activate the Ever Fresh
function by pressing the
relevant button on the external
display (the Ever Fresh icon will
light up). A slight noise can be
heard while the Ever Fresh
system is in operation.
7. Wait for the signal that the operation has finished
(the Ever Fresh icon will switch off).
8. Unlock the container from its position by pressing
the button on the shelf.
9. Take it out of the refrigerator
D
and turn the knob clockwise to
the CLOSE position to avoid
accidental opening (see figureA). The absence of air inside
the container is indicated by
the valve at the bottom (see
figure D).
GB
7
GB
E
! The lid of the container is provided with a circular
valve. When the valve is low (figure D) there is no air
inside the container. When the valve is high (figure E)
air is present inside the container.
10. To open the container, turn
the knob anticlockwise to the
OPEN position (see figure A):
this will allow air to enter the
container and make it easy to
open. The valve will move
upwards as air enters the
container (see figure E).
The containers were designed to come into direct
contact with food.
Do not use the containers for any type of cooking (in
the microwave or oven, on an electric plate, over a
flame, etc.).
Do not put the containers in the freezer.
Do not clean the lids in a dishwasher.
Vacuum storage
Pre-packed foods stored using the vacuum system
must still be consumed before the use-by date.
! If, after you have created a vacuum (instructions
1-9), the valve moves upward (see figure E) within
three days, check the lid has been put on the container
properly and/or that the container is intact. Check the
storage status of the food before repeating the vacuum
storage operation.
! The Ever Fresh function is equipped with a safety
device that switches off the pump in case of
malfunction (if the container is missing or incorrectly
positioned, for example). If the safety device is
activated, the Ever Fresh button must be pressed to
restore normal operation.
Using Ever Fresh to its full potential
The following information is a guide on how to get the
best from the Ever Fresh system and the food it stores.
Ever Fresh containers
The maximum fill level marked on the container must
be respected when storing liquids of any kind.
Vacuuming actual liquid from the container may
damage the Ever Fresh pump.
Repeated opening of the vacuumed containers may
disturb the storage conditions of the food inside.
Before using the system, make sure there is no
visible damage on any part of the container.
The container valve has a built-in security system. If,
after you have created a vacuum, the valve moves
upward within three days, check the lid has been
put on the container properly and/or that the
container is intact. Check the storage status of the
food before repeating the vacuum storage
operation. See Activating and deactivating EverFresh.
Repeatedly storing these vacuum-packed foods
does not change their natural tendency to spoil.
Do not store defrosted foods using the vacuum
system unless they have been cooked already.
Stored food should be prepared while fresh
(chopped, sliced, peeled, cooked) and should be in
perfect condition.
Perishable foods stored using the vacuum system
must still be stored inside the refrigerator.
Cooked foods must be left to cool before being
stored using the vacuum system.
Using the refrigerator to its full
potential
Adjust the temperature using the display.
Activate the SUPER COOL function to lower the
temperature quickly, for example, when you place a
large number of new food items inside a fridge and
the internal temperature rises slightly. This function
quickly cools the groceries by temporarily reducing
the temperature until it reaches the ideal level.
Place only cold or lukewarm foods in the
compartment, never hot foods (see Precautions andtips).
Remember that cooked foods do not last longer than
raw foods.
Do not store liquids in open containers: they will
increase the level of humidity in the refrigerator and
cause condensation to form.
8
FRUIT and VEGETABLE bin
The salad crispers fitted inside the fridge have been
specially designed for the purpose of keeping fruit and
vegetables fresh and crisp. Open the humidity
regulator (position B) if you want to store food in a less
humid environment, or close it (position A) to store
food in a more humid environment.
A
B
Using the freezer to its full potential
Adjust the temperature using the display.
To freeze foods in safely and correctly, follow the
instructions below: place the food in the FREEZER
and STORAGE compartment, making sure that it
does not come into contact with any food that has
already been frozen; press the rapid-freezing
SUPER FREEZE button (the corresponding LED
lights up) and close the door. The function
deactivates automatically after 24 hours or when the
inside of the compartment has reached the optimal
temperature (the LED switches off).
! Do not open the door during freezing.
GB
! If there is a power cut or malfunction, do not open the
freezer door. This will help maintain the temperature
inside the freezer, ensuring that foods are conserved for
at least 9 -14 hours.
! To avoid blocking the air circulation inside the freezer,
it is advisable not to obstruct the ventilation holes with
food or containers.
Do not re-freeze food that is defrosting or that has
already been defrosted. These foods must be
cooked and eaten (within 24 hours).
Fresh food that needs to be frozen must not come
into contact with food that has already been
defrosted.
Do not place glass bottles which contain liquids,
and which are corked or hermetically sealed in the
freezer because they could break.
The maximum quantity of food that may be frozen daily
is indicated on the plate containing the technical
properties located on the bottom left side of the
refrigerator compartment (for example: Kg/24h: 4).
9
Maintenance and care
GB
Switching the appliance off
During cleaning and maintenance it is necessary to
disconnect the appliance from the electricity supply:
1. Hold the ON/OFF button down for more than two
seconds until OFF appears on both indicator
displays (refrigerator and freezer).
2. Pull the plug out of the socket.
! If this procedure is not followed, the alarm may
sound. This alarm does not indicate a malfunction. To
restore normal operation, hold the ON/OFF button
down for more than two seconds. To disconnect the
appliance, follow points 1 and 2 above.
Cleaning the appliance
The external and internal parts and the rubber seals
may be cleaned using a sponge that has been
soaked in lukewarm water and bicarbonate of soda
or neutral soap. Do not use solvents, abrasive
products, bleach or ammonia.
The removable accessories may be soaked in warm
soapy water or dishwashing liquid. Rinse and dry
them carefully.
The back of the appliance may collect dust. This can
be removed by carefully using the hose of a vacuum
cleaner set on medium power. The appliance must
be switched off and the plug disconnected from the
electricity mains before it is cleaned.
Ever Fresh
Use a clean dry cloth to clean the opening of the
vacuum system in the centre of the Ever Fresh shelf.
Do not use water or solvents.
The opening in the centre of the Ever Fresh shelf should
not come into contact with water or any other liquids.
Wash and dry the containers before using them.
Do not clean the lids in a dishwasher.
Before closing the containers make sure that the
edges are clean. Traces of dirt may affect the
sealing process and consequently the length of time
food may be stored.
If the knob on the cover needs to be cleaned, turn it
anticlockwise until it comes off and wash it using
water and neutral detergent. After drying it
thoroughly, screw it back on.
If you wish to take the Ever Fresh shelf out and clean it,
you must first disconnect the tube at the back of the
shelf. Make sure it is reattached properly in order to
avoid blockages and system malfunctions. The Ever
Fresh shelf should not come into contact with water or
other liquids as these may damage the system.
Avoiding mould and unpleasant odours
The appliance is manufactured with hygienic, odour
free materials. Food should be wrapped well and
containers closed properly in order to maintain this
hygiene. This will also prevent the formation of
stains.
If you wish to switch the appliance off for an
extended period of time, clean the inside and leave
the doors open.
Replacing the light bulb
To replace the light bulb in the refrigerator
compartment, pull out the plug from the electrical
socket. Follow the
instructions below.
Access the light bulb by
removing the cover as
indicated in the diagram.
Replace it with a similar
2
1
light bulb within the
power range indicated
on the cover (10 W, 15
W or 25 W).
Changing the odour filter
The filter should be replaced approximately 6-8 months
after it has been activated. This period may vary
depending on the type of food stored inside the
refrigerator. For information on where a replacement
filter may be purchased, contact Assistance (seeAssistance). To replace the filter, follow the instructions
(see diagrams A and B).
10
Precautions and tips
! The appliance was designed and manufactured in
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
This appliance complies with the following
European Community Directives:
- 73/23/EEC dated 19/02/73 (Low Voltage) and
subsequent amendments;
-89/336/EEC dated 03.05.89 (Electromagnetic
Compatibility) and subsequent amendments;
- 2002/96/CE.
General safety
The appliance was designed for domestic use
inside the home and is not intended for commercial
or industrial use.
The appliance must be used by adults only to store
and freeze food products according to the
instructions in this manual.
The appliance must not be installed outdoors, even
in covered areas. It is extremely dangerous to leave
the appliance exposed to rain and storms.
Disposal
GB
Observe local environmental standards when
disposing of packaging material as some of this
material may be recycled.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE),
requires that old household electrical appliances
must not be disposed of in the normal unsorted
municipal waste stream. Old appliances must be
collected separately in order to optimise the
recovery and recycling of the materials they contain
and reduce the impact on human health and the
environment. The crossed out wheeled bin symbol
on the product reminds you of your obligation, that
when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Respecting and conserving the
environment
Do not touch the appliance when barefoot or with
wet or damp hands and feet.
Do not touch the internal cooling elements: this
could cause skin abrasions or frost/freezer burns.
When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
Always switch the appliance off and disconnect it
from the electrical supply before cleaning it or
carrying out maintenance work. It is NOT sufficient
to hold the ON/OFF button down for more than two
seconds to eliminate all electrical contact.
In case of malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance.
Do not use any sharp or pointed utensils or
electrical equipment - other than the type
recommended by the manufacturer - inside the
frozen food storage compartments.
Do not put ice cubes taken directly from the freezer
into your mouth.
Install the appliance in a cool, well-ventilated room.
Ensure that it is protected from direct sunlight and
do not place it near sources of heat.
Try to avoid keeping the door open for long periods.
A significant amount of energy is used every time
the door is opened.
Do not over-fill the appliance: cold air must circulate
freely for food to be preserved properly. If air
circulation is impeded, the compressor will work
continuously.
Do not place hot food in the refrigerator. The internal
temperature will increase, forcing the compressor to
work harder and consume more energy.
Regularly check the door seals and wipe clean to
ensure they are free of debris and to prevent cold
air from escaping (see Maintenance).
Do not allow children to tamper with the controls or
play with the appliance. Under no circumstances
should they be allowed to sit on the bins or to hang
from the door.
Keep packaging material out of reach of children.
11
Troubleshooting
GB
If the appliance does not work, before calling for Assistance (see Assistance), check for a solution from the following list.
Malfunctions:
The display is completely switched off.
The motor does not start.
The display is on but it is dim.
The alarm sounds, a message
appears on the display, the ALARM
LED lights up and the refrigerator
light flashes.
The alarm sounds, the ALARM LED
lights up and a message appears on
the display.
The alarm sounds, the ALARM LED
flashes and a message appears on
the display.
Possible causes / Solutions:
The plug has not been inserted into the electrical socket, or not far
enough to make contact, or there is no power in the house.
The appliance comes with a motor protection control (see Start-up and use).
Pull out and reverse the plug before putting it back in the socket.
The refrigerator door has been open for more than two minutes.
The buzzer stops when the door is closed or when the RESET ALARM
button is pressed.
The temperature inside the freezer is too high.
The freezer will maintain a temperature of around 0°C so that the food
will not refreeze, allowing you to eat it within 24 hours or to refreeze it
after it has been cooked.
To switch off the buzzer, press the RESET ALARM button. Press again
to delete the message on the display, switch off the ALARM LED and
restore normal operation.
The temperature of the freezer is dangerously high: the food inside must not
be eaten. The freezer will maintain a temperature of approximately -18°C.
To switch off the buzzer, press the RESET ALARM button. Press again to
delete the message on the display, switch off the ALARM LED and restore
normal operation.
The refrigerator and the freezer do not
cool well.
The food inside the refrigerator is
beginning to freeze.
The motor runs continuously.
The Aircooler fan does not rotate
The appliance makes a lot of noise.
Early ending of functions
The doors do not close properly or the seals are damaged.
The doors are opened too frequently.
The temperature that has been set is too high (see Start-up and use).
The refrigerator or the freezer have been over-filled.
The temperature that has been set is too low (see Start-up and use).
The SUPER FREEZE button has been pressed (rapid freezing): the
yellow SUPER FREEZE light is on or flashing (see Description).
The door is not closed properly or is continuously opened.
The outside ambient temperature is very high.
The thickness of the frost exceeds 2-3 mm (see Maintenance).
The refrigerator door is open.
The Aircooler system is only activated automatically when it becomes
necessary to restore perfect operational conditions inside the
refrigerator compartment.
The appliance has not been installed on a level surface (see Installation).
The appliance has been installed between cabinets that vibrate and
make noise.
The internal refrigerant makes a slight noise even when the compressor
is off. This is not a defect, it is normal.
Electrical disturbance on the network or brief interruptions of the power supply
A message appears on the display
(e.g. F01)
12
The water discharge hole is blocked (see Maintenance).
Assistance
Before calling for Assistance:
Check if the malfunction can be solved on your own (see Troubleshooting).
If after all the checks, the appliance still does not operate or the problem persists, call the nearest Service
Centre
model
Communicating:
type of malfunction
appliance model (Mod.)
serial number (S/N)
This information can be found on the data
plate located on the bottom left side of the
refrigerator compartment.
Never call on unauthorized technicians and always refuse spare parts which are not originals.
serial number
GB
13
GB
195072008.00
09/2008
14
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.