Hotpoint HSS25ASHSS, HSS25ATHBB, HSS25ATHWW User Manual

GEAppliances.com

Safety Instructions .................2–3

Operating Instructions

Automatic Icemaker ..................12,13

Care and Cleaning ...................15,16

Crispers and Pans .......................11

ExpressChill

Ice and Water Dispenser ................14

Refrigerator Doors ......................10

Replacing the Light Bulbs .............16,17

Shelves and Bins .......................8, 9

Temperature Controls ....................4

TurboCool

Side by Side

ClimateKepper2 ..........................5

Water Filter ..............................7

Installation Instructions

Installing the Refrigerator ............ 23–26

Moving the Refrigerator .............19–22

Preparing to Install

the Refrigerator .........................18

Water Line Installation ..............27–29

Troubleshooting Tips ............31–33

Normal Operating Sounds ...............30

™

.............................5

..............................5

Owner’s Manual

and Installation

Models 22, 23, 25,26,27 and 29

Côte à Côte

Réfrigérateurs

Manuel d’utilisation

et d’installation

La section française commence à la page 40

Lado a Lado

Refrigeradores

Manual del propietario

e instalación

La sección en español empieza en la página 75

Consumer Support

Consumer Support .............Back Cover

Performance Data Sheets ............34,35

Warranty ...............................36

Write the model and serial numbers here:

Model # _________________________ Serial # __________________________

Find these numbers on a label inside the refrigerator compartment at the top on the

Refrigerators

right side.

200D8074P051 49-60646-4 10-14 GE

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

SAFETY

GE Appliances Website

For more information on your refrigerator’s operation, visit www.GEAppliances.com or

call 800.GECARES (800.432.2737). In Canada visit GEAppliances.ca or call 800.561.3344.

REFRIGERATOR SAFETY INFORMATION

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All

safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are defined as:

DANGER

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

 This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is used.

 Unplug the refrigerator before making repairs, replacing a light

bulb, or cleaning. Note: Power to the refrigerator cannot be disconnected by any setting on the control panel. Note: Repairs must be performed by a qualified service professional.

 Replace all parts and panels before operating.  Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

To reduce the risk of fire, explosion, electric shock, or injury when using your

refrigerator follow these basic safety precautions:



Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord. However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

 To prevent suffocation and entrapment hazards to children,

remove the fresh food and freezer doors from any refrigerator before disposing of it or discontinuing its use.

 Do not allow children to climb, stand or hang on the door

handles or the shelves in the refrigerator. They could seriously injure themselves.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

 Do not clean glass shelves or covers with warm water

when they are cold. Glass shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping or dropping. Tempered glass is designed to shatter into many small pieces if it breaks.

 Keep fingers out of the “pinch point” areas; clearances

between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

To reduce the risk of injury when using your refrigerator, follow these basic

safety precautions.

 Do not touch the cold surfaces in the freezer compartment

when hands are damp or wet, skin may stick to these extremely cold surfaces.

 Do not refreeze frozen foods which have thawed

completely.



In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes. Do not place fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in.

GEAppliances.com

SAFETY (CONT.)

INSTALLATION

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can result in fire, explosion, or death.

CONNECTING ELECTRICITY

WARNING

Plug into a grounded 3-prong outlet Do not remove the ground prong Do not use an adapter Failure to follow these instructions can result in death, fire, or electrical shock.

Electrical Shock Hazard.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Do not use an adapter.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded electrical supply is required. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

PROPER DISPOSAL OF YOUR OLD REFRIGERATOR

WARNING

Remove fresh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can result in child entrapment which can lead to death or brain damage.

IMPORTANT:

Suffocation and child entrapment hazard.

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

 Take off the fresh food and freezer doors.  Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old refrigeration product, check with the company handling the disposal about what to do.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

About the temperature controls.

Not all features are on all models. Your controls may be similar to the following:

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

The temperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on usage and operating environment.





On some models, setting both controls to the warmest setting until the display flashes (off) will stop cooling in both the freezer and refrigerator compartments.





On other models, setting either control to the warmest setting until the display flashes (off) will stop the cooling to the freezer and refrigerator.





NOTE: Turning the refrigerator off via the controls on the touch panel does not shut off electrical power to the refrigerator.

NOTE: The refrigerator is shipped with protective film- covering the temperature controls. If this film was not removed during installation, remove it now.

Performance Air Flow System

The Performance Air-Flow System is designed to maximize temperature control in the refrigerator and freezer compartments. This unique special feature consists of the Air Tower along the back wall of the refrigerator and the Air Tunnel on the bottom portion of the freezer rear wall.

Placing food in front of the louvers on these components will not affect performance. Although the Air Tower and the Air Tunnel can be removed, doing so will affect temperature performance. (For removal instructions, on-line, 24 hours a day, contact us at GEAppliances.com or call 800.GE.CARES. In Canada, contact us at geappliances.ca or call

1.800.561.3344.)

About ClimateKeeper2.

How it Works

The ClimateKeeper2™ is the industry’s most advanced refrigeration system, delivering optimum temperature and humidity performance to keep food garden fresh longer and reduce freezer burn.

The ClimateKeeper2™ system features two

HYDSRUDWRUV³RQHIRUWKHUHIULJHUDWRUDQGRQH

for the freezer. This provides two separate cooling systems,

and separates the airflow between the fresh food and freezer compartments during normal cooling operations.*

This ensures that the humidity levels in the fresh food compartment are significantly higher than in a conventional system,** allowing fresh produce and other unsealed foods to retain their moisture content and freshness longer. Moisture sensitive foods such as fresh fruit, salads, rice, etc., can now be stored on open shelves without excessive moisture loss.

™

(on some models) GEAppliances.com

Due to the higher humidity in the refrigerator, you may on occasion experience fog or small amounts of moisture in the refrigerator compartment. This is normal and may come and go as different food loads and environmental conditions change. Wipe dry with a paper towel if desired.

The separate airflow system minimizes the mixing of air between the two compartments, which reduces fresh food odor transfer to improve the taste of ice.

The ClimateKeeper2™ system also reduces the number of defrosting cycles in the freezer evaporator, thereby reducing freezer burn.

* Freezer air is used in the CustomCool™ feature. ** Testing shows a higher level of humidity in

the Fresh Food section in ClimateKeeper2™ refrigerators versus conventional units.

About TurboCool.™ (on some models)

How it Works

TurboCool ™ rapidly cools the refrigerator

compartment in order to more quickly cool foods. Use TurboCool ™ when adding a large amount of food to the refrigerator compartment, putting away foods after they have been sitting out at room temperature or when putting away warm leftovers. It can also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn on immediately and the fans will cycle on and off at high speed as needed for eight hours. The compressor will continue to run until the refrigerator compartment cools to approximately 34°F (1°C), then it will cycle on and off to maintain this setting. After 8 hours, or if TurboCool ™ is pressed again, the refrigerator compartment will return to the original setting.

How to Use

Press TurboCool.™ The TurboCool ™ temperature display will show Tc and the LED will be activated.

After TurboCool ™ is complete, the TurboCool indicator light will go out.

NOTES: The refrigerator temperature cannot be

changed during TurboCool ™.

The freezer temperature is not affected

during TurboCool ™.

When opening the refrigerator door during

TurboCool

if they have cycled on.

™

, the fans will continue to run

™

About ExpressChill™. (on some models)

How it Works

The ExpressChill™ feature is a system of dampers, a fan and a temperature thermistor.

The pan is tightly sealed to prevent the pan’s temperature from causing temperature fluctuations in the rest of the refrigerator.

How to Use

Empty the pan. Place the Chill tray in the pan. Place the items on the tray and close the pan completely.

Select the ExpressChill™ pad. On some models, you can then select the chill time (use chart to determine best setting). Other

ExpressChill™

models will only have one option (45 minutes). On models with multiple settings, tap the pad until the light appears next to

The controls for this pan are located in the top of the refrigerator or on the dispenser with the temperature controls.

the desired setting.





To stop a feature before it is finished, tap that feature’s pad until no options are selected and the display is off.





During ExpressChill™, the display on the controls will count down the time in the cycle.

How to Remove and Replace the Drawer

To remove:

Pull the drawer out to the stop position. Rotate all four swing locks to the unlock

position. Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are in the unlock position.

Place the sides of the drawer into the drawer supports, making sure the swing locks fit on the drawer slots.

Lock all four swing locks by rotating them to the lock position.

ExpressChill™ Chart (on some models)

NOTE: Results may vary depending on packaging, starting temperature and other food traits.

15 Minutes



1 Beverage Can (12 oz)





2 Small Juice Boxes



(6–8 oz each)

















30 Minutes

2 to 6 Beverage Cans (12 oz each)

2 Plastic 20 oz Bottles of Beverage

4 to 6 Small Juice Boxes (6–8 oz each)

3 Foil Juice Packets Wine (750 ml bottle)

45 Minutes



2 Liters of Beverage





1/2 Gallon of Juice





*HODWLQ³SDFNDJH



About the water filter. (on some models) GEAppliances.com

Water Filter Cartridge

The water filter cartridge is located in the back upper right corner of the refrigerator compartment.

When to Replace the Filter on Models With a Replacement Indicator Light

There is a replacement indicator light for the water filter cartridge on the dispenser. This light will turn orange to tell you that you need to replace the filter soon.

The filter cartridge should be replaced when the replacement indicator light turns red or if the flow of water to the dispenser or icemaker decreases.

When to Replace the Filter on Models Without a Replacement Indicator Light

The filter cartridge should be replaced every six months or earlier if the flow of water to the water dispenser or icemaker decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one by slowly turning it to the left. Do not pull down on the cartridge. A small amount of water may drip down.

Installing the Filter Cartridge

If you are replacing a SmartWater cartridge with an adapter, it must be removed before installing the cartridge. To remove the adapter, turn it to the left about 1/4 turn.

If you are replacing a Water by Culligan cartridge, leave the adapter in place. This adapter will stay in the refrigerator when you replace future cartridges.

Run water from the dispenser 1-1/2 gallons (about three minutes) to clear the system and prevent sputtering.

Press and hold the WATER FILTER pad (on some models) on the dispenser for 3 seconds.

NOTE: A newly-installed water filter cartridge may cause water to spurt from the dispenser upon first use.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter cartridge is not available. The dispenser and the icemaker will not operate without the filter or filter bypass plug.

Filter Bypass Plug

Cartridge Holder

SmartWater

Filter Bypass Plug

Water by Culligan

Some models

With adapter

(appearance may vary)

On models ithout a replacement indicator light, apply the month and year sticker to the new cartridge to remind you to replace the filter in six months.

Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after installation.

Line up the arrow on the cartridge and the cartridge holder. Place the top of the new cartridge up inside the holder. Do not push it up into the holder.

Slowly turn it to the right until the filter cartridge stops. DO NOT OVERTIGHTEN. As you turn the cartridge, it will automatically raise itself into position. The cartridge will move about 1/2 turn.

Without adapter

use this type of

water filter.

To use the filter bypass plug on Water by Culligan models, you must first remove the filter adapter from the cartridge holder by turning it to the left.

For the maximum benefit of your filtration system, GE recommends the use of GE branded SmartWater filters only. Using GE branded filters in GE and Hotpoint refrigerators provides optimal performance and reliability. GE branded SmartWater filters are always the right choice because they are patented and designed specifically for GE products. GE SmartWater filters meet rigorous industry NSF standards for safety and quality that are important for products that are filtering your water. GE has not qualified non-GE branded filters for use in GE and Hotpoint refrigerators and there is no assurance that non-GE branded filters meet GE’s standards for quality, performance and reliability.

,I\RXKDYHTXHVWLRQV³YLVLWRXU:HEVLWHDWGEAppliances.com, or call 1.800.GE.CARES (1.800.432.2737).

Replacement filters:

To order additional filter cartridges in the United States, visit our Website at GEAppliances.com, or call GE Parts and Accessories,

800.626.2002.

See filter label for type of filter to order (MWF or MSWF). Customers in Canada should consult the yellow pages for the

nearest Mabe Service Center.

About the shelves and bins.

Not all features are on all models.

Snugger

Refrigerator bin

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins

The larger refrigerator door bins and freezer tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight up, then lift up and out.

To replace or relocate: Engage the back side of the bin in the molded supports of the door. Then push down on the front of the bin. Bin will lock in place.

Small Bins To remove: Lift the front of the bin straight up

then out.

The snugger helps prevent tipping, spilling or sliding of small items stored on the door shelf. Place a finger on either side of the snugger near the rear and move it back and forth to fit your needs.

Top freezer bin

NOTE:

Be careful when placing items in the top bin. Make sure that items do not block or fall into the ice chute.

Freezer bin

Freezer tilt-out bin

Press tab and pull shelf forward to remove

To replace: Position the bin above the rectangular molded supports on the door. Then slide the bin down onto the support to lock it in place.

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you to reach items stored behind others. The special edges are designed to help prevent spills from dripping to lower shelves.

To replace or relocate:

Line the shelf up with the supports and slide it into place. The shelf can be repositioned when the door is at 90° or more. To reposition the shelf, slide the shelf past the stops and angle downward. Slide shelf down to the desired

To remove:

Slide the shelf out until it reaches the stop, then press down on the tab and slide the shelf straight out.

position, line up with the supports and slide into place.

Make sure you push the shelves all the way back in before you close the door.

Freezer Baskets (on some models)

To remove, slide out to the stop position, lift the

front past the stop position, and slide out.

Make sure you push the baskets all the way back in before you close the door.

Freezer Baskets (on some models)

To remove, push the basket all the way to the

back of the freezer. Lift up until the back pins are disengaged. Lift the entire basket up and pull out.

Make sure you push the baskets all the way back in before you close the door.

About the shelves and bins.

Not all features are on all models.

QuickSpace™ Shelf (on some models)

This shelf splits in half and slides under itself for storage of tall items on the shelf below.

This shelf can be removed and replaced or relocated just like Slide-Out Spillproof Shelves.

Slide-Out Freezer Shelves

To remove, slide out to the stop position, lift the front past the stop position, and slide out from rib.

Fixed Freezer Shelves

To remove, lift the shelf up at the left side and

then bring the shelf out.

Door Wine/Beverage Rack

(on some models)

This rack holds up to 5 cans, one bottle of wine or one 2-liter bottle of soda.

The rack hangs from the sides of the dairy bin.

To remove:

Empty the wine/beverage rack.

GEAppliances.com

On some models, this shelf can not be used in the lowest position.

Make sure you push the shelves all the way back in before you close the door.

NOTE FOR DISPENSER MODELS: In order to take full advantage of the tilt-out ice bin (on some models), only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

Holding the bottom of the dairy bin, lift the front straight up, then lift up and out.

To detach the rack from the dairy bin, pull the rack’s side wires out of the holes on each side of the dairy bin.

ShelfSaver™ Rack

(on some models)

Use this rack to store beverage cans for easy access.

It can also hold a 9” x 13” baking dish.

Removable Beverage Rack

(on some models)

The beverage rack is designed to hold a bottle on its side. It can be attached to any slide-out shelf.

To replace:

Reattach the rack to the sides of the bin.

Engage the back side of the bin in the molded supports on the door. Then push down on the front of the bin. The bin will lock into place.

Door Can Rack

(on some models)

This door rack holds up to 9 cans.

NOTE: This rack can only be mounted in the top position under the dairy bin.

To install:

Line up the large part of the slots on the top of the rack with the tabs under the shelf.

Then slide the rack back to lock it in place.

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors may feel different than the ones you are used to. The special door opening/closing feature makes sure the doors close all the way and are securely sealed.

When opening and closing the door you will notice a stop position. If the door is opened past this stop point, the door will remain open to allow you to load and unload food more easily. When the door is only partially open, it will automatically close.

When the door is only partially open, it will automatically close.

Beyond this stop the door will stay open.

Door Alignment

If doors are uneven, adjust the refrigerator door.

Using a 7/16” socket wrench, turn the

door adjusting screw to the right to raise the door; to the left, to lower it. (A nylon plug, imbedded in the threads of the pin, prevents the pin from turning unless a wrench is used.)

(on some models)

The resistance you feel at the stop position will be reduced as the door is loaded with food.

After one or two turns of the wrench,

open and close the refrigerator door and check the alignment at the top of the doors.

To remove the base grille, open the doors, remove the screw at each end of the base grille and then pull the grille straight out.

7/16” Socket Wrench

Raise

About the crispers and pans. GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the bottom of the drawers should be wiped dry.

On some models, the bottom drawer has full extension slides that allow full access to the drawer.

Adjustable Humidity Crispers

Slide the control all the way to the HI setting to provide high humidity recommended for most vegetables.

Convertible Deli Pan (on some models)

The convertible deli pan has its own cold air duct to allow a stream of cold air from the freezer compartment or refrigerator compartment to flow to the pan.

The variable temperature control regulates the air flow from the Climate Keeper.

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling the drawer straight out and lifting the drawer up and over the stop location.

Slide the control all the way to the LO setting to provide lower humidity levels recommended for most fruits.

Set the control to the coldest setting to store fresh meats.

Set the control to cold to convert the panto normal refrigerator temperature and provide extra vegetable storage space. The cold air duct is turned off. Variable settings between these extremes can be selected.

If the door prevents you from taking out the drawers, first try to remove the door bins. If this does not offer enough clearance, the refrigerator will need to be rolled forward until the door opens enough to slide the drawers out. In some cases, when you roll the refrigerator out, you will need to move the refrigerator to the left or right as you roll it out.

About the automatic icemaker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Icemaker

7KHLFHPDNHUZLOOSURGXFHVHYHQFXEHVSHUF\FOH³

approximately 100–130 cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

If the refrigerator is operated before the water connection is made to the icemaker, set the power switch in the OFF position.

When the refrigerator has been connected to the water supply, set the power switch to the ON position.

The icemaker will fill with water when it cools to 15°F (–10°C). A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes.

You will hear a buzzing sound each time the icemaker fills with water.

Throw away the first few batches of ice to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm. When the bin fills to the level of the feeler arm, the icemaker will

stop producing ice. It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink.

CAUTION

the ejector mechanism, or with the heating element (located on the bottom of the ice maker) that releases the cubes. Do not place fingers or hands on the automatic ice making

mechanism while the refrigerator is plugged in.

Avoid contact with the moving parts of

Special note about dispenser models:

 Some models have a tilt-out ice bin. The bin can be tilted

out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before closing the door.

 To restore your ice level from an empty bucket stage, the

following steps are recommended:

12 hours after the first batch of ice has fallen into the bin,

dispense 3 to 4 cubes.

After an additional 6 hours, dispense 3 to 4 cubes again.

These steps will restore your ice level in the shortest amount of time.

Power Switch

Green Power Light

(on some models)

Icemaker

Feeler Arm

Power Switch

(on some models)

Icemaker

Feeler Arm

NOTE:

In homes with lower than average water pressure, you may hear the icemaker cycle multiple times when making one batch of ice.

About the automatic icemaker. (cont) GEAppliances.com

Accessing Ice and Reaching the Power Switch on Dispenser Models

There are two types of ice storage bins on dispenser models.

One has a shelf above the bin, the other does not.

Special note for models with tilt-out ice bin:

 These models have a tilt-out ice bin. The bin can be tilted

out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before closing the door.

NOTE: In order to take full advantage of the tilt-out ice bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

Models with a shelf above the ice bin

Shelf

Ice Bin

To reach the power switch, pull the shelf straight out. Always be sure to

To access ice, pull the bin forward.

replace the shelf.

Shelf

Ice Bin

Models with tilt out ice bin

To access ice and reach the icemaker power switch:

Lift the bin, then pull it forward until the bin stops.

Lower the bin to access ice or reach the power switch.

Removing Ice Bin (dispenser models)

CAUTION

Set the power switch to the OFF position before removing the bin.

When replacing the bin, be sure to press it firmly into place. If it does not go all the way back, remove it and rotate the drive mechanism 1/4 turn. Then push the bin back again.

The ice bin is heavy when full.

On some models, to access ice or reach the power switch:

Pull the bin forward until the bin stops.

Rotate

Lower the bin to access ice or reach the power switch.

Drive Mechanism

Dispenser Models only

About the ice and water dispenser. (on some models)

To Use the Dispenser

Spill Shelf

Select CUBED ICE , CRUSHED ICE or WATER .

Press the glass gently against the top of the dispenser cradle.

The spill shelf is not self-draining. To reduce water spotting, the shelf and its grille should be cleaned regularly.

If no water is dispensed when the refrigerator is first installed, there may be air in the water line system. Press the dispenser arm for at least two minutes to remove trapped air from the water line and to fill the water system. To flush out impurities in the water line, throw away the first six glassfuls of water.

CAUTION: Never put fingers or any other objects into the ice crusher discharge opening.

Locking the Dispenser

Press the LOCK pad for

3 seconds to lock the dispenser and control panel. To unlock, press and hold the pad again for 3 seconds.

Dispenser Light

This pad turns the light in the

dispenser on and off. The light also comes on when the dispenser cradle is pressed. For models with a bulb, if the light burns out, it should be replaced with a 6 watt 12V maximum bulb. For LED models, contact Factory Service.

Quick Ice (on some models)

When you need ice in a

hurry, press this pad to speed up ice production. This will increase ice production for the following 48 hours or until you press the pad again.

Door Alarm (on some

models) To set the alarm, press this

pad until the indicator light comes on. This alarm will sound if either door is open for more than 3 minutes. The light goes out and the beeping stops when you close the door.

Important Facts About Your Dispenser

 Do not add ice from trays or bags to the

storage drawer. It may not crush or dispense well.

 Avoid overfilling glass with ice and use of

narrow glasses. Backed-up ice can jam the chute or cause the door in the chute to freeze shut. If ice is blocking the chute, poke it through with a wooden spoon.

 Beverages and foods should not be quick-

chilled in the ice storage drawer. Cans, bottles or food packages in the storage drawer may cause the icemaker or auger to jam.

 To keep dispensed ice from missing the

glass, put the glass close to, but not touching, the dispenser opening.

 Some crushed ice may be dispensed

even though you selected CUBED ICE. This happens occasionally when a few cubes accidentally get directed to the crusher.

 After crushed ice is dispensed, some water

may drip from the chute.

 Sometimes a small mound of snow will form

on the door in the ice chute. This condition is normal and usually occurs when you have dispensed crushed ice repeatedly. The snow will eventually evaporate.

Care and cleaning of the refrigerator. GEAppliances.com

Cleaning the Outside

Dispenser drip area.

The dispenser drip area, beneath the grille, shou l d b e w i p e d dr y . W a t e r left in this area may leave deposits. Remove the deposits by adding undiluted vinegar to the well. Soak until the deposits disappear or become loose enough to rinse away.

The dispenser cradle. Before cleaning, lock the dispenser by pressing and holding the LOCK pad for 3 seconds. Clean with warm water and

EDNLQJVRGDVROXWLRQ³DERXWDWDEOHVSRRQ

ml) of baking soda to a quart (1 liter) of water. Rinse thoroughly and wipe dry.

The door handles and trim. Clean with a cloth dampened with soapy water. Dry with a soft cloth.

Cleaning the Inside

To help prevent odors, leave an open box

of baking soda in the fresh food and freezer compartments.

Unplug the refrigerator before cleaning. If this is not practical, wring excess moisture out of sponge or cloth when cleaning around switches, lights or controls.

8VHZDUPZDWHUDQGEDNLQJVRGDVROXWLRQ³

about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and neutralizes odors. Rinse and wipe dry.

The stainless steel doors and door handles (on some models) can be cleaned with a commercially available stainless steel cleaner. Cleaners with oxalic acid such as Bar Keepers Friend Soft Cleanser™ will remove rust, tarnish and small blemishes. Use only a liquid cleanser free of grit and rub in the direction of the brush lines with a damp soft sponge.

Do not use appliance wax or polish on the stainless steel.

Keep the outside clean. Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may leave a residue that can erode the paint. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.

CAUTION

or covers with warm water when they are cold. Glass shelves and covers may break if exposed to sudden temperature changes or impact such as bumping or dropping. Tempered glass is designed to shatter into many small pieces if it breaks.

Do not wash any plastic refrigerator parts in the dishwasher.

The chill/thaw tray is dishwasher safe.

Do not clean glass shelves

Use of any cleaning solution other than that which is recommended, especially those that contain petroleum distillates, can crack or damage the interior of the refrigerator.

Care and cleaning of the refrigerator. (cont.)

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. All types of floor coverings can be damaged, particularly cushioned coverings and those with embossed surfaces.

Pull the refrigerator straight out and return it to position by pushing it straight in. Moving the refrigerator in a side direction may result in damage to the floor covering or refrigerator.

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigerator. Clean the interior with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the doors open.

Set the icemaker power switch to the OFF position and shut off the water supply to the refrigerator.

Preparing to Move

Secure all loose items such as shelves and drawers by taping them securely in place to prevent damage.

When pushing the refrigerator back, make sure you don’t roll over the power cord or icemaker supply line (on some models).

If the temperature can drop below freezing, have a qualified servicer drain the water supply system (on some models) to prevent serious property damage due to flooding.

Be sure the refrigerator stays in an upright position during moving.

When using a hand truck to move the refrigerator, do not rest the front or back of the refrigerator against the hand truck. This could damage the refrigerator. Handle only from the sides of the refrigerator.

Replacing the light bulbs. (on some models)

WARNING

live wire filament. (A burned-out light bulb may break when being replaced.) Turning the control to the OFF position does not remove power to the light circuit.

Your light shield will look like one of the following:

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a

5HIULJHUDWRU&RPSDUWPHQW³8SSHU/LJKW

Unplug the refrigerator. The bulbs are located at the top of the

compartment, inside the light shield. On

Tabs

Pocket

some models, a screw at the front of the light shield will have to be removed. On other models, the screw is located in the pocket located at the back of the shield.

To remove the light shield, on some models,

press in on the tabs on the sides of the shield and slide forward and out. On other models, just slide the shield forward and out.

After replacing the bulb with an appliance

bulb of the same or lower wattage, replace the light shield and screw. When replacing the light shield, make sure that the tabs at the back of the shield fit into the slots at the back of the light shield housing.

Plug the refrigerator back in.

Replacing the light bulbs. (cont) GEAppliances.com

WARNING

live wire filament. (A burned-out light bulb may break when being replaced.) Turning the control to the OFF position does not remove power to the light circuit.

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a

5HIULJHUDWRU&RPSDUWPHQW³/RZHU/LJKW

This light is located above the top drawer.

Unplug the refrigerator. Lift the light shield up and pull it out.

Freezer Compartment

Unplug the refrigerator. Remove the shelf just above the light shield.

(The shelf will be easier to remove if it is emptied first.) Remove the screw at the top of the light shield.

To remove the light shield, press in on the

sides, and lift up and out.

After replacing the bulb with an appliance

bulb of the same or lower wattage, replace the shield.

Plug the refrigerator back in.

Replace the bulb with an appliance bulb

of the same or lower wattage, and reinstall the light shield. When reinstalling the light shield, make sure the top tabs snap securely into place. Replace the screw.

Reinstall the shelf and plug the

refrigerator back in.

Dispenser (on some models)

Unplug the refrigerator. The bulb is located on the dispenser under

the control panel. Remove the light bulb by turning it counterclockwise.

Replace the bulb with a bulb of the same

size and wattage.

Plug the refrigerator back in.

Replacing the lights on models with LED lighting

Setting the controls to OFF does not remove power to the light circuit. Not all features are on all models.

Refrigerator Compartment (on some models)

There is an LED lighting display in the top and sides of the fresh food compartment and in the rear

LED Lighting Display

and side of the freezer compartment on some models. If this assembly needs to be replaced, call GE Service at 1.800.432.2737 in the United States or

1.800.561.3344 in Canada.

Installation

Refrigerator

Instructions

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

Models 22, 23, 25, 26, 27 & 29

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT ³6DYHWKHVHLQVWUXFWLRQVIRU

local inspector’s use.

•

IMPORTANT ³2EVHUYHDOOJRYHUQLQJ

codes and ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for future reference.

• Skill level – Installation of this appliance requires basic mechanical skills.

• Completion time –

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

If the refrigerator has already been installed, remove the base grille (see Step 2 in Moving the Refrigerator), then skip to Step 5 in Installing the Refrigerator.

Refrigerator Installation

30 minutes

Water Line Installation 30 minutes

PREPARATION

WATER SUPPLY TO THE ICEMAKER

If the refrigerator has an icemaker, it will have to be connected to a cold water line. A GE water supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at GEAppliances. com (in Canada at www.geappliances.ca) or from Parts and Accessories, 800.626.2002 (in Canada

1.800.661.1616).

TOOLS YOU WILL NEED

3/8” and 5/16” Socket 1/2” and 7/16” Wrench

Plastic Putty Knife

Phillips Head Screwdriver

Installation Instructions

MOVING THE REFRIGERATOR

LOADING THE REFRIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors until the refrigerator is in its final location.

To move the refrigerator, use a padded hand truck. Center the refrigerator on the hand truck and secure the strap around the refrigerator.

DO NOT OVERTIGHTEN THE STRAP.

If the refrigerator must go through any entrance that is less than 38” wide, the doors must be removed. Proceed to Step 3.

DO NOT remove the handles.

If all entrances are more than 38” wide, skip to Installing the Refrigerator.

DISCONNECT THE WATER COUPLING

(on some models)

If the refrigerator has a water dispenser, there is a water line from the cabinet into the bottom hinge on the freezer door that must be disconnected.

To disconnect, push in on the white collar of the coupling and pull out the tubing.

White collar

REMOVE THE BASE GRILLE

Remove the grille by removing the two Phillips head screws.

Bottom freezer hinge

Installation Instructions

MOVING THE REFRIGERATOR (CONT.)

DISCONNECT THE POWER COUPLING

(on some models)

If the refrigerator has a water dispenser,

there is a power line (harness) from the cabinet into the bottom hinge on the freezer door that must be disconnected.

To disconnect, pull apart at the coupling.

Bottom freezer hinge

DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

If the refrigerator has a refreshment center,

there are electrical connectors (harnesses) from the cabinet into the bottom hinge on the refrigerator door that must be disconnected.

To disconnect, pull apart each connector.

CLOSE THE FREEZER AND

REFRIGERATOR DOORS

REMOVE THE FREEZER DOOR

Remove the freezer door top hinge cover (if

equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

Remove the two 5/16” hex head screws, then

lift the hinge straight up to free the hinge pin.

5/16” Hex Head

Bottom refrigerator hinge

Open the freezer door to 90.°

90°

Installation Instructions

REMOVE THE FREEZER DOOR (cont.)

As one person slowly lifts the freezer door up

and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.

90°

Set the door on a non-scratching surface with

the inside up.

REMOVE THE REFRIGERATOR DOOR

Remove the refrigerator door top hinge cover

(if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

REMOVE THE REFRIGERATOR DOOR

(cont.)

Remove the two 5/16” hex head screws, then

lift the hinge straight up to free the hinge pin.

5/16” Hex Head

Open the refrigerator door to 90.°

90°

Installation Instructions

MOVING THE REFRIGERATOR (CONT.)

REMOVE THE REFRIGERATOR DOOR

(cont.)

Lift the refrigerator door up and off the bottom

hinge. If the refrigerator has a refreshment center,

one person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the bottom hinge.

90°

REPLACING THE DOORS

To replace the doors, simply reverse steps 3 through 8.

However, please note the following:

• When lowering the doors onto the bottom hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.

• When connecting the water line, make sure you insert the tubing all the way to the mark.

Refreshment Center Models only

Set the door on a non-scratching surface with

the inside up.

Mark

• Do not pinch the tubing and harnesses when placing the doors on the bottom hinges.

• When connecting the power line and the electrical lines (refreshment center models only), be sure that the connectors are seated together fully.

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the

temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature will go above 100°F (37°C) because it will not perform properly.

• Do not install the refrigerator in a location exposed to water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections:

23‘/25‘ 23‘ (33” wide), CustomStyle™ 25‘, 26‘, 27‘, 29‘

Sides 1/8” (4 mm) 1/8” (4 mm) Top 1” (25 mm) 1” (25 mm) Back 1/2” (13 mm) -1” (25 mm)

DIMENSIONS AND SPECIFICATIONS (for 23‘ CustomStyle

™

models)

701ø4” (178.4 cm)

36”

(91.4 cm)

24” (61 cm)

DIMENSIONS AND SPECIFICATIONS (for 25‘ CustomStyle

™

models)

DIMENSIONS AND SPECIFICATIONS

Electrical

25” (63.5 cm) Countertop

24” (61 cm) Cabinet

Water

3/4” (19 mm) Airspace (1/2” [13 mm] Gap + 1/4” [6 mm] Wall Plates)

721ø4” (183.5 cm)*

36”

(91.4 cm)

24” (61 cm)

* 721/4” (183.5 cm) required for full adjustment

of mobility wheels. If cabinets installed above refrigerator have doors that are flush to the top of the opening for the refrigerator, then an additional 1/8” may be required to provide clearance for cabinet doors to open freely.

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT.)

CONNECTING THE REFRIGERATOR TO

THE HOUSE WATER LINE (icemaker and dispenser models)

A cold water supply is required for automatic icemaker and dispenser operation. If there is not a cold water supply, you will need to provide one. See “Installing the Water Line” section.

NOTES:

• Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet.

• If your refrigerator does not have a water filter, we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator’s water valve. Install it in the water line near the refrigerator. If using GE SmartConnect Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to install filter.

If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supply.

If you are using the GE SmartConnect the nuts are already assembled to the tubing.

If you are using copper tubing, insert the end of

the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting.

If you are using GE SmartConnect insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening may cause leaks.

™

Refrigerator

™

tubing,

™

tubing,

Fasten the tubing into the clamp provided to

hold it in position. You may need to pry open the clamp.

Tubing Clamp

1/4” Compression Nut

Ferrule (sleeve)

Refrigerator Connection

TURN ON THE WATER SUPPLY

Turn the water on at the shutoff valve (house water supply) and check for any leaks.

PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make sure the icemaker power switch is set to the OFF position.

SmartConnect™ Tubing

1/4” Tubing

Option 2

See the grounding information attached to the power cord.

Installation Instructions

PUT THE REFRIGERATOR IN PLACE

Move the refrigerator to its final location.

LEVEL THE REFRIGERATOR (cont.)

To adjust the rollers on 23

CustomStyle

‘/25‘

™

models:

LEVEL THE REFRIGERATOR

The refrigerator can be leveled by adjusting the rollers located near the bottom hinges.

Rollers

Rollers have three purposes:

• Rollers adjust so the door closes easily when

opened about halfway. (Raise the front about 5/8” [16 mm] from the floor.)

• Rollers adjust so the refrigerator is firmly positioned on the floor and does not wobble.

• Rollers allow you to move the refrigerator away from the wall for cleaning.

To adjust the rollers on 23‘ (33” wide), 25‘, 26‘, 27‘ and 29‘ models:

• Turn the roller

adjusting screws clockwise to raise the refrigerator,

counterclockwise to lower it. Use a

3/8” hex socket or wrench, or an adjustable wrench.

Raise

Turn the front roller adjusting screws clockwise to raise the refrigerator,

counterclockwise to lower it. Use a 3/8” hex

wrench with extension, or an adjustable wrench. These models also have rear adjustable

rollers so you can align the refrigerator with your kitchen cabinets. Use a 3/8” hex wrench with extension to turn the screws for the rear

UROOHUV³clockwise to raise the refrigerator, counterclockwise to lower it.

LEVEL THE DOORS

Adjust the refrigerator door to make the doors

even at the top. To align:

Using a 7/16” wrench, turn the door adjusting screw to the right to raise the door, to the left to lower it.

NOTE:

A nylon plug, imbedded in the threads of the pin, prevents the pin from turning unless a wrench is used.

After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.

Doors should be even at top

Roller adjusting screws

Roller adjusting screw

Raise

7/16” wrench

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT.)

REPLACE THE BASE GRILLE

Replace the grille by installing the two Phillips head screws.

START THE ICEMAKER

Set the icemaker power switch to the I (on) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (–9°C) or below. It will then begin operation automatically. It will take 2–3 days to fill the ice bin.

Power switch

SET THE CONTROLS

Set the controls to the recommended setting.

NOTE:

In lower water pressure conditions, the water valve may turn on up to 3 times to deliver enough water to the icemaker.

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER & DISPENSER MODELS)

BEFORE YOU BEGIN

Recommended copper water supply kits are WX8X2, WX8X3 or WX8X4, depending on the amount of tubing you need. Approved plastic water supply lines are GE SmartConnect WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE Reverse Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse osmosis water systems, follow the manufacturer’s recommendations.

If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System AND the refrigerator also has a water filter, use the refrigerator’s filter bypass plug. Using the refrigerator’s water filtration cartridge in conjunction with the RO filter can result in hollow ice cubes and slower water flow from the water dispenser.

This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage.

™

Refrigerator Tubing (WX08X10006,

WHAT YOU WILL NEED

• Copper or GE SmartConnect™ Refrigerator Tubing kit, 1/4” outer diameter to connect the refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing you need: measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall after installation.

GE SmartConnect available in the following lengths:

™

Refrigerator Tubing Kits are

8’ (2.8 m) – WX08X10006 15’ (4.6 m) – WX08X10015 25’ (7.6 m) – WX08X10025

Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook up the water line to the hot water line.

If you use your refrigerator before connecting the water line, make sure the icemaker power switch is in the OFF position.

Do not install the icemaker tubing in areas where temperatures fall below freezing.

When using any electrical device (such as a power drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered.

All installations must be in accordance with local plumbing code requirements.

Installation Instructions

INSTALLING THE WATER LINE (CONT.)

Install the shutoff valve on the nearest frequently used

WHAT YOU WILL NEED (CONT.)

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect kits. Do not use any other plastic water supply line because the line is under pressure at all times. Certain types of plastic will crack or rupture with age and cause water damage to your home.

• A GE water supply kit (containing tubing, shutoff valve and fittings listed below) is available at extra cost from your dealer or from Parts and Accessories, 800.626.2002 (in Canada

1.800.661.1616).

• A cold water supply. The water pressure must be between 20 and 120 p.s.i. (1.4–8.1 bar).

™

Refrigerator Tubing

drinking water line.

SHUT OFF THE MAIN WATER SUPPLY

CHOOSE THE VALVE LOCATION

Choose a location for the valve that is easily

Turn on the nearest faucet long enough to clear the line of water.

accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

• Power drill.

• 1/2” or adjustable wrench.

• Straight and Phillips blade screwdriver.

• Two 1/4” outer diameter compression nuts and 2 ferrules (sleeves)³WRFRQQHFWWKHFRSSHUWXELQJWR

the shutoff valve and the refrigerator water valve.

• If you are using a GE SmartConnect Tubing kit, the necessary fittings are preassembled to the tubing.

• If your existing copper water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting. Do not cut formed end from GE SmartConnect

™

Refrigerator tubing.

™

Refrigerator

DRILL THE HOLE FOR THE VALVE

Drill a 1/4” hole in the water pipe (even if using

a self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the

drill.

Failure to drill a 1/4” hole may result in reduced

ice production or smaller cubes.

• Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32” at the point of connection to the COLD WATER LINE. Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Installation Instructions

FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe

with the pipe clamp.

Pipe Clamp

Saddle-Type Shutoff Valve

NOTE: Commonwealth of Massachusetts

Vertical Cold Water Pipe

Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing

washer begins to swell.

NOTE: Do not overtighten or you may crush the

tubing.

Washer

Pipe Clamp

Inlet End

CONNECT THE TUBING TO THE VALVE

Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect Refrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight, then tighten one additional turn with a wrench. Overtightening may cause leaks.

Saddle-Type Shutoff Valve

Packing Nut

Outlet Valve

Compression Nut

SmartConnect™ Tubing

Ferrule (sleeve)

NOTE: Commonwealth of Massachusetts

Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

™

Clamp Screw

ROUTE THE TUBING

Route the tubing between the cold water line

and the refrigerator.

Route the tubing through a hole drilled in the

wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall after installation.

FLUSH OUT THE TUBING

Turn the main water supply on and flush out the tubing until the water is clear.

Shut the water off at the water valve after about one quart (1 liter) of water has been flushed through the tubing.

To complete the installation of the refrigerator, go back to Step 1 in Installing the Refrigerator.

Normal operating sounds.

Newer refrigerators sound different from older refrigerators. Modern refrigerators have more features and use newer technology.

Do you hear what I hear? These sounds are normal.

HUMMM...

WHOOSH...



The new high efficiency compressor may run faster and longer than your old refrigerator and you may hear a high-pitched hum or pulsating sound while it is operating.



Sometimes the refrigerator runs for an extended period, especially when the doors are opened frequently. This means that the Frost Guard™ feature is working to prevent freezer burn and improve food preservation.



You may hear a whooshing sound when the doors close. This is due to pressure equalizing within the refrigerator.



You may hear the fans spinning at high speeds. This happens when the refrigerator is first plugged in, when the doors are opened frequently or when a large amount of food is added to the refrigerator or freezer compartments. The fans are helping to maintain the correct temperatures.





If either door is open for over 3 minutes, you may hear the fans come on in order to cool the light bulbs.



The fans change speeds in order to provide optimal cooling and energy savings.

CLICKS, POPS,

CRACKS and CHIRPS



You may hear cracking or popping sounds when the refrigerator is first plugged in. This happens as the refrigerator cools to the correct temperature.





Electronic dampers click open and closed to provide optimal cooling and energy savings.



The compressor may cause a clicking or chirping sound when attempting to restart (this could take up to 5 minutes).



The electronic control board may cause a clicking sound when relays activate to control refrigerator components.



Expansion and contraction of cooling coils during and after defrost can cause a cracking or popping sound.



On models with an icemaker, after an icemaking cycle, you may hear the ice cubes dropping into the ice bucket.

WATER SOUNDS



The flow of refrigerant through the freezer cooling coils may make a gurgling noise like boiling water.



Water dropping on the defrost heater can cause a sizzling, popping or buzzing sound during the defrost cycle.



A water dripping noise may occur during the defrost cycle as ice melts from the evaporator and flows into the drain pan.





Closing the door may cause a gurgling sound due to pressure equalization.

For additional information on normal icemaker and dispenser operating sounds, see the About the automatic icemaker and About the ice and water dispenser sections.

+ 98 hidden pages