Hotpoint FZ 830.1 IX NE /HA, FQ 830.1 User Manual

Operating Instructions

OVEN

English,1 Dansk, 12

FI SE

Suomi, 34 Svenska, 45

FZ 830.1 NE/HA FZ 830.1 IX NE/HA FQ 830.1 NE/HA

Norsk,23

Contents

Installation, 2-3

Positioning Electrical connections

Description of the appliance, 4

Overall view Control panel

Start-up and use, 5

Starting the oven Data plate

The electronic cooking programmer, 6

Cooking modes, 7-9

Cooking modes Practical cooking advice Cooking advice table

Precautions and tips, 10

General safety Disposal Respecting and conserving the environment Assistance

Maintenance and care, 11

Switching the appliance off Cleaning the appliance Cleaning the oven door Replacing the light bulb

Installation

560 m

45 mm.

 Before placing your new appliance into operation please read these operating instructions carefully. They contain important information for safe use, for installation and for care of the appliance.

 Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance.

Positioning

 Keep packaging material out of the reach of children.It can become a choking or suffocation hazard. see Precautions and tips).

! The appliance must be installed by a qualified person in compliance with the instructions provided. Incorrect installation may cause harm to persons, animals or may damage property.

Fitting the appliance

Use the appropriate cabinet to ensure that the appliance functions properly.

 The panels adjacent to the oven must be made of

heat-resistant material.

Ventilation

To ensure good ventilation, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of wood, or on a completely flat surface with an opening of at least 45 x 560 mm (see diagrams).

Centring and fastening

Position the 4 tabs on the side of the oven according to the 4 holes of the outer frame. Adjust the tabs according to the thickness of the cabinet side panel, as shown below:

thickness of 20 mm: take off the removable part of the tab (see diagram)

 Cabinets with a veneer exterior must be assembled

with glues which can withstand temperatures of up to 100°C.

 To install the oven under the counter (see diagram)

and in a kitchen unit, the cabinet must have the following dimensions:

. m

567 mm.

45 mm.

558 mm.

593 mm.

23 mm.

595 mm.

5 mm.

595 mm.

545 mm.

24 mm.

! The appliance must not come into contact with electrical parts once it has been installed. The consumption indications on the data plate have been calculated for this type of installation.

thickness of 18 mm: use the first groove, which has already been set in the factory (see diagram)

thickness of 16 mm: use the second groove (see diagram)

Secure the appliance to the cabinet by opening the oven door and putting 4 screws into the 4 holes of the outer frame.

! All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool.

Electrical connections

! Ovens equipped with a three-pole power supply

cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate located on the appliance (see below).

Fitting the power supply cable

1. Open the terminal board by inserting a screwdriver into the side tabs of the cover. Use the screwdriver as a lever by pushing it down to open the cover (see diagram).

2. Loosen the cable clamp screw and

remove it, using a screwdriver as a lever (see figure).

3. Remove the wire contact screws L-N, then fasten the wires under the screw heads, respecting the colour code: Blue (N), Brown (L) and Yellow-Green Verde (

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indicated on the data plate (see side). The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains, suitable for the load indicated and complying with current electrical regulations (the earthing wire must not be interrupted by the circuitbreaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations.

Before connecting to the power supply, make sure that:

 The appliance is earthed and the plug is

compliant with the law.

 The socket can withstand the maximum power of

the appliance, which is indicated on the data plate (see below).

 The voltage must be in the range between the

values indicated on the data plate (see below).

 The socket is compatible with the plug of the

appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only (see Assistance).

! The manufacturer declines any liability should these safety measures not be observed.

Description of the appliance

Overall view

DRIPPING PAN

Control panel

GRILL

SELECTOR

Knob

GUIDES for the sliding racks

position 5

position 4 position 3 position 2 position 1

THERMOSTAT

Knob

Indicator light

THERMOSTAT

•• ••

ELECTRONIC

Programmer

Start-up and use

! The first time you use your appliance, heat the empty

oven with its door closed at its maximum temperature for at least half an hour. Ensure that the room is well ventilated before switching the oven off and opening the oven door. The appliance may produce a slightly unpleasant odour caused by the burning away of protective substances used during the manufacturing process.

Starting the oven

1. Select the desired cooking mode by turning the SELECTOR knob.

2. Select the desired temperature with the THERMOSTAT knob. See the Cooking advice table for cooking modes and the suggested cooking temperatures (see Cooking Modes).

3. When lit, the THERMOSTAT indicator light indicates that the oven is heating up to the temperature set.

4. You may do the following during cooking:

- change the cooking mode by turning the SELECTOR knob.

- change the temperature by turning the THERMOSTAT knob.

- stop cooking by turning the SELECTOR knob to the 0 position.

! Never put objects directly on the oven bottom to avoid damaging the enamel coating.

! Always place cookware on the rack(s) provided.

Cooling ventilation

In order to cool down the external temperature of the oven, some models are fitted with a cooling fan that blows out air between the control panel and the oven door. ! Once the cooking has been completed, the cooling fan remains on until the oven has cooled down sufficiently.

Oven light

It goes on when selecting

with the SELECTOR

knob. It stays on when a cooking mode is selected.

DATA PLATE

Dimensions

Volume

Electrical connections

width 43.5 cm height 32 cm depth 41,5 cm

lt. 58

voltage: 220-240V ~ 50Hz maximum power absorbed 2800W

ENERGY LABEL

Directive 2002/40/EC on the label of electric ovens. Standard EN 50304

Energy consumption for Natural convection – heating mode: Convection mode.

Declared energy consumption for Forced convection Class – heating mode: Baking.

This appliance conforms to the following European Economic Community directives:

- 2006/95/EEC of 12/12/06 (Low Voltage) and subsequent amendments;

- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent amendments;

- 93/68/EEC of 22/07/93 and subsequent amendments.

- 2002/96/EC

The electronic cooking programmer

DISPLAY

END OF

COOKING icon

DURATION

icon

DECREASE TIME

button

•• ••

SET TIME

button

CLOCK icon

TIMER icon

INCREASE TIME

button

Setting the clock

 The clock may be set when the oven is switched off or when it is switched on, provided that a the end time of a cooking cycle has not been programmed previously. After the appliance has been connected to the

mains, or after a blackout, the numerical digits on the DISPLAY will begin to flash.

1. Press the icon and the four digits on the display begin to flash.

2. Use the + and - buttons to adjust the time; if you press and hold either button, the display will scroll through the values more quickly, making it quicker and easier to set the desired value.

3. Wait for 10 seconds or press the to finalise the setting.

button several times until the

icon and the four

button again

Setting the timer

 This function does not interrupt cooking and does not affect the oven; it is simply used to activate the buzzer when the set amount of time has elapsed.

1. Press the icon and the three digits on the display begin to flash.

2. Use the + and - buttons to set the desired time; if you press and hold either button, the display will scroll through the values more quickly, making it quicker and easier to set the value.

3. Wait for 10 seconds or press the to finalise the setting. The display will then show the time as it counts down. When this period of time has elapsed the buzzer will be activated.

button several times until the

button again

Programming cooking

 A cooking mode must be selected before programming can take place.

Programming the cooking duration

1. Press the icon and the three digits on the DISPLAY begin to flash.

2. Use the + and - buttons to set the desired duration; if you press and hold either button, the display will scroll through the values more quickly, making it quicker and easier to set the value.

3. Wait for 10 seconds or press the to finalise the setting.

4. When the set time has elapsed, the text END appears on the DISPLAY, the oven will stop cooking and a buzzer sounds.  For example: it is 9:00 a.m. and a time of 1 hour

and 15 minutes is programmed. The programme will stop automatically at 10:15 a.m.

Setting the end time for a cooking mode

 A cooking duration must be set before the cooking end time can be scheduled.

1. Follow steps 1 to 3 to set the duration as detailed above.

2. Next, press the the four digits on the DISPLAY begin to flash.

3. use the + and - buttons to adjust the cooking end time; if you press and hold either button, the display will scroll through the values more quickly, making it quicker and easier to set the desired value.

4. Wait for 10 seconds or press the to finalise the setting.

5. When the set time has elapsed, the text END appears on the DISPLAY, the oven will stop cooking and a buzzer sounds.

Programming has been set when the buttons are illuminated. The DISPLAY shows the cooking end time and the cooking duration alternately.

Cancelling a programme

To cancel a programme:  press the

the setting you wish to cancel and the digits on the display are no longer flashing. Press the - button until the digits 00:00 appear on the display.

 Press and hold the + and - buttons; this will

cancel all the settings selected previously, including timer settings.

button several times until the

button again

button until the icon and

button again

and

button until the icon corresponding to

Cooking modes

! A temperature value can be set for all cooking modes between 60°C and Max, except for

 BARBECUE (recommended: set only to MAX power

level);

 GRATIN (recommended: do not exceed 200°C).

LEAVENING mode

The oven reaches and maintains a temperature of 40°C irrespective of the position of the THERMOSTAT knob. This mode is ideal for leavening dough made with yeast.

TRADITIONAL OVEN mode

Both the top and bottom heating elements will come on. With this traditional cooking mode, it is best to use one cooking rack only: if more than one rack is used, the heat distribution will be uneven.

BAKING mode

The rear heating element and the fan come on, guaranteeing the distribution of heat delicately and uniformly throughout the oven. This mode is ideal for baking and cooking temperature sensitive foods such as cakes that need to rise and to prepare certain tartlets on 3 shelves simultaneously.

FAST COOKING mode

PIZZA mode

The heating elements (bottom and circular) and the fan come on. This combination heats the oven rapidly by producing a considerable amount of heat, particularly from the bottom element. If you use more than one rack simultaneously, switch the position of the dishes halfway through the cooking process.

BARBECUE mode

The top heating element and the rotisserie (where present) come on. The high and direct temperature of the grill is recommended for food that requires high surface temperature. Always cook in this mode with the oven door closed.

GRATIN mode

The top heating element as well as the fan and the rotisserie (where present) come on. This combination of features increases the effectiveness of the unidirectional thermal radiation of the heating elements through forced circulation of the air throughout the oven. This helps prevent food from burning on the surface, allowing the heat to penetrate right into the food. Always cook in this mode with the oven door closed.

The Rotisserie (only available on certain models)

To operate the rotisserie (see diagram) proceed as follows:

The heating elements and the fan come on, guaranteeing the distribution of heat consistently and uniformly throughout the oven. Pre-heating is not necessary for this cooking mode. This mode is especially recommended for cooking pre-packed food quickly (frozen or pre-cooked). The best results are obtained if you use one cooking rack only.

MULTI-COOKING mode

All the heating elements (top, bottom and circular), as well as the fan, will come on. Since the heat remains constant throughout the oven, the air cooks and browns food uniformly. A maximum of two racks may be used at the same time.

1. Place the dripping pan in position 1.

2. Place the rotisserie support in position 3 and insert the spit in the hole provided on the back panel of the oven.

3. Start the rotisserie using the knob to select MODE or .

 When door is opened.

mode is on, the rotisserie will stop if the

Practical cooking advice

! Do not place racks in position 1 and 5 during fan-

assisted cooking. Excessive direct heat can burn temperature sensitive foods.

! In the BARBECUE and GRATIN cooking modes, particularly when using the rotisserie, place the dripping pan in position 1 to collect cooking residues (fat and/or grease).

MULTI-COOKING

 Use position 2 and 4, placing the food that requires

more heat on 2.

 Place the dripping pan on the bottom and the rack

on top.

BARBECUE

 Insert the rack in position 3 or 4. Place the food in

the centre of the rack.

 We recommend that you set the maximum power

level. The top heating element is regulated by a thermostat and may not always be on.

PIZZA MODE

 Use a light aluminium pizza pan. Place it on the

rack provided. For a crispy crust, do not use the dripping pan (prevents crust from forming by extending cooking time).

 If the pizza has a lot of toppings, we recommend

adding the mozzarella cheese on top of the pizza halfway through the cooking process.

Cooking advice table

Cooking

modes

Leavening

Traditional

Oven

Baking

Mode

Fast

cooking

Multi-

cooking

Pizza Mode

Barbecue

Gratin

Foods Weight

Leavening process of dough made with yeast or baking powder (brioches, bread, sugar pie, croissants, etc.) Duck Roast veal or beef Pork roast Biscuits (short pastry) Tarts Tarts Fruit cakes Plum cake Sponge cake Stuffed pancakes (on 2 racks) Small cakes (on 2 racks) Cheese puffs (on 2 racks) Cream puffs (on 3 racks) Biscuits (on 3 racks) Meringues (on 3 racks)

Frozen food

Pizza Courgette and prawn pie Country style spinach pie Turnovers Lasagne Golden Rolls Chicken morsels

Pre-cooked food

Golden chicken wings 0.4 2 - 200 20-25

Fresh Food

Biscuits (short pastry) Plum cake Cheese puffs Pizza (on 2 racks) Lasagne Lamb Roast chicken + potatoes Mackerel Plum cake Cream puffs (on 2 racks) Biscuits (on 2 racks) Sponge cake (on 1 rack) Sponge cake (on 2 racks) Savoury pies Pizza Roast veal or beef Chicken Soles and cuttlefish Squid and prawn kebabs Cuttlefish Cod filet Grilled vegetables Veal steak Sausages Hamburgers Mackerels Toasted sandwiches (or toast) With rotisserie (where present) Veal on the spit Chicken on the spit Lamb on the spit Grilled chicken Cuttlefish With rotisserie (where present) Veal on the spit Lamb on the spit Chicken on the spit + potatoes (roasted)

(in kg)

1 1 1

0.5 1

0.7

0.5

1.2

0.6

0.4

0.7

0.5

0.3

0.4

0.5

0.3

0.5

0.4

0.3

0.6

0.2 1 1 1

1+1

1 1

0.5

0.5 1

1.5

0.5 1 1

0.7

0.6

0.8

0.4

0.8

0.6

0.6 1

4 and 6

1.0

1.5

1.0

1.5

Rack Position Pre-heating

time

(minutes)

3 3 3 3 3 3

2 or 3

3 2 and 4 2 and 4 2 and 4

1 and 3 and 5 1 and 3 and 5 1 and 3 and 5

2 2 and 4

2 2 and 4 2 and 4

2 2 and 4

2 or 3

3 or 4

2 2

15 15 15 15 15 15 15 15 15 15 15 15 15 15 15

15 10 10 15 10 10

10 10 10 10 15 15 10 10

10 10

10 10 10 10

Recommended

temperature

200 200 200 180 180 180 180 180 160 200 190 210 180 180

250 200 220 200 200 180 220

200 180 210 230 180 180 200 180 170 190 180 170 170 200 220 220

180 Max Max Max Max Max Max Max Max Max Max

Max Max Max

200

Cooking

time

(minutes)

65-75 70-75 70-80 15-20 30-35 20-30 40-45 40-50 25-30 30-35 20-25 15-20 20-25 20-25

180

12 20

30-35

35 25-30 15-20

15-18

45 10-12

15-20 30-35 40-45 60-70 30-35 40-50 20-25 10-15 15-20 20-25 25-30 15-20 25-30 60-70 10-12

8-10 10-15 10-15 15-20 15-20 15-20 10-12 15-20

3-5

80-90 70-80 70-80 55-60 30-35

70-80 70-80 70-75 70-75

Precautions and tips

! The appliance was designed and manufactured in compliance with

international safety standards. The following warnings are provided for safety reasons and must be read carefully.

General safety

 The appliance was designed for domestic use inside the home

and is not intended for commercial or industrial use.

 The appliance must not be installed outdoors, even in covered

areas. It is extremely dangerous to leave the appliance exposed to rain and storms.

 When handling the appliance, always use the handles provided

on the sides of the oven.

 Do not touch the appliance with bare feet or with wet or moist

hands and feet.

 The appliance must be used to cook food by adults only and

according to the instructions in this manual.

 When the appliance is in use, the heating

elements and some parts of the oven door become extremely hot. Make sure you don't

touch

them and keep children well away.

 Ensure that the power supply cable of other electrical appliances

does not come into contact with the hot parts of the oven.

 The openings used for ventilation and dispersion of heat must

never be covered.

inexperienced persons may cause injury or further malfunctioning of the appliance. Contact a Service Centre (see Assistance).

 Do not rest heavy objects on the open oven door.

 The appliance should not be operated by people (including

children) with reduced physical, sensory or mental capacities, by inexperienced individuals or by anyone who is not familiar with the product. These individuals should, at the very least, be supervised by someone who assumes responsibility for their safety or receive preliminary instructions relating to the operation of the appliance.

 Do not let children play with the appliance.

Disposal

 Observe local environmental standards when disposing packaging

material for recycling purposes. Observe existing legislation when disposing of the old appliance.

 The European Directive 2002/96/EC on Waste Electrical and

Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out wheeled bin symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

 Always grip the oven door handle in the centre: the ends may be

hot.

 Always use oven gloves to place cookware in the oven or when

removing it.

 Do not use aluminium foil to line the bottom of the oven.

 Do not place flammable materials in the oven: if the appliance is

switched on by mistake, it could catch fire.

 Always make sure the knobs are in the l/

appliance is not in use.

 When unplugging the appliance always pull the plug from the

mains socket, do not pull on the cable.

 Never carry out any cleaning or maintenance work without having

unplugged the plug from the mains.

 In the case of a malfunction, under no circumstances should you

attempt to repair the appliance yourself. Repairs carried out by

¡ position when the

Respecting and conserving the environment

 By using the appliance in the hours between late afternoon and

early morning, you can help reduce the work load placed on electrical companies.

 Always keep the oven door closed when using the BARBECUE

and GRATIN modes: to attain best results and to save energy (approximately 10%).

 Regularly check the door seals and wipe clean to ensure they are

free of debris so that they stick properly to the door and do not allow heat to disperse.

Assistance

Communicating:

 appliance model (Mod.)  serial number (S/N) This information is found on the data plate located on the appliance and/or on the packaging.

Maintenance and care

Switching the appliance off

Disconnect your appliance from the electricity supply before carrying out any work on it.

Cleaning the appliance

 The stainless-steel or enamel-coated external

parts as well as the rubber seals may be cleaned using a sponge that has been soaked in lukewarm water and neutral soap. If these stains are difficult to remove, use only specialised products. After cleaning, rinse and dry thoroughly. Do not use abrasive powders or corrosive substances.

 Ideally, the inside of the oven should be cleaned

after each use, when it is still lukewarm. Use hot water and detergent, rinse and dry with a soft cloth. Do not use abrasive products.

 All accessories - with the exception of the sliding

racks - can be washed like everyday crockery.  Never use steam cleaners or pressure cleaners on the appliance.

Cleaning the oven door

Clean the glass part of the oven door using a sponge and a non-abrasive cleaning product, then dry thoroughly with a soft cloth. Do not use rough abrasive material or sharp metal scrapers as these could scratch the surface and cause the glass to crack.

To clean more thoroughly, you can remove the oven door.

1. Open the oven door fully (see diagram).

2. Lift up and turn the small levers located on the two hinges (see diagram).

Inspecting the seals

Check the door seals around the oven periodically. If the seals are damaged, please contact your nearest After-sales Service Centre (see Assistance). We recommend not using the oven until the seals have been replaced.

Replacing the light bulb

To replace the oven light bulb:

1. Remove the glass cover of the lamp-holder.

2. Remove the light bulb and replace it with a similar one: Wattage 25 W, cap E 14.

3. Replace the glass cover (see diagram).

3. Grip the door on the two external sides and close it approximately half way. Unlock the door by pressing on the clamps ., then pull the

door towards you lifting it out of its seat (see diagram). To replace the door, reverse this sequence.

Brugervejledning

OVN

English,1 Dansk, 12

FI SE

Suomi, 34 Svenska, 45

FZ 830.1 NE/HA

FZ 830.1 IX NE/HA

FQ 830.1 NE/HA

Norsk,23

Oversigt

Installation, 13-14

Placering Elektrisk tilslutning

Beskrivelse af ovnen, 15

Samlet illustration Betjeningspanel

Start og brug, 16

Sådan tændes for ovnen Typeskilt

Elektronisk programmeringsenhed, 17

Programmer, 18-20

Tilberedningsprogrammer Praktiske råd til tilberedning Skema over tilberedning

Forskrifter og råd, 21

Generelt om sikkerheden Bortskaffelse Spar på energien og værn om miljøet

Vedligeholdelse, 22

Afbrydelse af strømmen Rengøring af apparatet Rengøring af ovndøren Udskiftning af pære Service

560 m

45 mm.

Installation

 Det er vigtigt at opbevare dette hæfte et sted, så det nemt kan konsulteres. Hvis apparatet sælges, overdrages eller flyttes, skal man sørge for, at brugervejledningen følger med, så den nye ejer kan få oplysninger om apparatets funktion og eventuelle advarsler.

 Læs omhyggeligt instruktionerne: De indeholder vigtige oplysninger om installation, anvendelse og sikkerhed.

Placering

 Emballagen må ikke betragtes som legetøj til børn, og den skal bortskaffes i henhold til bestemmelserne om sortering af affald (se afsnittet Forskrifter og råd).

 Installationen skal udføres i overensstemmelse med instruktionerne og af en kvalificeret tekniker. En fejlagtig installation kan medføre personskade, skader på dyr samt materielle skader.

Indbygning

For at ovnen skal kunne fungere korrekt, skal indbygningsskabet være egnet dertil:

 Panelerne på skabene ved siden af ovnen skal

være lavet af materialer, der er modstandsdygtige

over for varme.

Ventilation

For at sikre en god ventilation, er det nødvendigt at afmontere den bageste væg på indbygningsskabet. Det tilrådes at installere ovnen, så den støtter på to trælister eller på en plan overflade med en åbning på minimum 45 x 560 mm (se figuren).

Centrering og fastgørelse

Placér de 4 stifter på siden af ovnen ud for de 4 huller på omkredsrammen, idet der tages hensyn til køkkenelementets tykkelse:

Tykkelse på 20 mm: Fjern den bevægelige del af den udragende stift (se figuren).

 På skabe af finerplader skal limen være

modstandsdygtig over for temperaturer på 100ºC.

 Hvis ovnen indbygges i et skab, både ved

montering under en bordplade (se figuren) og ved

søjleopbygning, skal skabet have følgende mål:

. m

567 mm.

45 mm.

558 m

593 mm.

23 mm.

595 mm.

5 mm.

595 mm.

545 mm.

24 mm.

 Når ovnen er blevet indbygget, må der ikke være mulighed for eventuelt kontakt med de elektriske dele. Oplysningerne om energiforbrug, angivet på typeskiltet, er målt på denne type installation.

Tykkelse på 18 mm: Brug den første rille, som allerede findes ved levering fra fabrikken (se figuren).

Tykkelse på 16 mm: Brug den anden rille (se figuren).

Sådan fastgøres ovnen til køkkenelementet: Åbn ovndøren, og skru de 4 skruer i de 4 passende huller på omkredsrammen.

 Alle sikkerhedsdele skal være monteret på en sådan måde, at de ikke kan fjernes uden brug af værktøj.

Elektrisk tilslutning

 Ovne, der er udstyret med et trepolet

forsyningskabel er klargjort til funktion med

vekselstrøm ved den spænding og frekvens, der er

anført på ovnens typeskilt (se herunder).

Montering af forsyningskabel

1. Åbn klemrækken ved at stikke en skruetrækker ned i klapperne på siden af dækslet. Træk og åbn dækslet (se figuren).

2. Løsn skruen i kabelklemmen, og tag den ud ved at vrikke skruetrækkeren (se

figuren).

3. Tag skruerne af kontakterne L-Nfastgør de små ledninger under skruehovederne i overensstemmelse med farverne Blå (N) Brun (L) Gulgrøn (

Tilslutning af strømforsyningskablet til nettet

Anvend et standardstik på kablet til den belastning, der er anført på typeskiltet (se her ved siden af). Hvis man ønsker en direkte forbindelse til el-nettet, skal man indsætte en flerpolet afbryder med en minimumsåbning mellem kontakterne på 3 mm. i overensstemmelse med belastningen og i overensstemmelse med de gældende regler (der skal ikke være en afbryder på jordforbindelsen). Forsyningskablet skal være placeret på en sådan måde, at det ikke når en temperatur på 50º C over omgivelsestemperaturen på noget punkt.

 Installatøren er ansvarlig for en korrekt elektrisk tilslutning samt overholdelse af sikkerhedsreglerne. Inden tilslutningen udføres, skal man kontrollere følgende:

 at stikkontakten har jordforbindelse og er i

overensstemmelse med loven,

 at stikkontakten kan bære apparatets maksimale

spændingsbelastning, som angivet på typeskiltet (se herunder),

 at forsyningsspændingen ligger inden for

værdierne, som angivet på typeskiltet (se herunder),

 at stikkontakten passer til apparatets stik. I modsat

fald skal man udskifte stikkontakten eller stikket. Undgå anvendelse af forlængerledninger eller flerdobbelte stikdåser.

 Når apparatet er installeret, skal man nemt kunne nå ind til både ledning og stikkontakt.

 Ledningen må ikke bøjes eller trykkes sammen.

 Ledningen skal regelmæssigt kontrolleres og må kun

udskiftes af autoriserede teknikere (se afsnittet Service).

 Virksomheden fralægger sig såfremt disse regler ikke overholdes.

ethvert ansvar,

Beskrivelse af apparatet

Samlet illustration

Betjeningspanel

BRADEPANDE

Betjeningspanel

RIST

GLIDESKINNER

til pladerne

rille 5 rille 4 rille 3 rille 2 rille 1

PROGRAMVÆLGER TERMOSTATKNAP

Kontrollampe for

TERMOSTAT

•• ••

ELEKTRONISK

pro

rammeringsenhed

Start og brug

Når ovnen tændes første gang, anbefales det at lade

ovnen være i funktion i tom tilstand i mindst en time

med termostaten indstillet på maksimum og ovndøren

lukket. Herefter skal man åbne ovndøren og udlufte

lokalet. Lugten, der opstår, skyldes fordampning af

beskyttelsesmidlerne i ovnen.

Sådan tændes for ovnen

1. Vælg det ønskede tilberedningsprogram ved at

dreje på PROGRAMKNAPPEN.

2. Indstil temperaturen ved at dreje på knappen

TERMOSTAT. Der findes en liste over tilberedninger

og de anbefalede temperaturer i tilberedningsskemaet

(se afsnittet Programmer).

3. Kontrollampen TERMOSTAT angiver, at ovnen er i

gang med at varme op til den valgte temperatur

4. Under tilberedningen er det altid muligt at:

- ændre programmet ved at dreje på

PROGRAMKNAPPEN,

- ændre temperaturen ved hjælp af

TERMOSTATKNAPPEN,

- afbryde tilberedningen ved at dreje

PROGRAMKNAPPEN over på position 0.

Afkølingsventilation

For at mindske den udvendige temperatur, er nogle modeller udstyret med en afkølingsblæser. Blæseren skaber en luftstråle, der blæses ud gennem betjeningspanelet og ovndøren.  Ved afsluttet tilberedning fortsætter blæseren med at være tændt, indtil ovnen er passende afkølet.

Ovnlys

Lyset tændes ved at vælge

med knappen PROGRAMMER. Den bliver ved med at lyse, når der vælges et tilberedningsprogram.

 Undgå at placere genstande i bunden af ovnen, da det kan beskadige ovnens lakering.

 Placér altid beholderne på den medfølgende rist.

TYPESKILT

Mål

Volumen Elektriske

tilslutninger

ENERGIMÆRKNING

Dette apparat er i

bredde 43,5 cm højde 32 cm dybde 41,5 cm

lt. 58 spænding 220-240V ~ 50Hz

maks. optaget effekt 2800W Direktiv 2002/40/EF på de

elektriske ovnes etikette Standard EN 50304 Energiforbrug ved naturlig varmestrømning opvarmningsfunktion: Traditionel ovn;

Erklæret energiforbrug for klasse med forceret varmestrømning opvarmningsfunktion: Fint bagværk.

overensstemmelse med følgende EU-direktiver: 2006/95/EØF af 12/12/06 (Lavspænding) og efterfølgende ændringer 89/336/EØF af 03/05/89 (Elektromagnetisk kompatibilitet) og efterfølgende ændringer - 93/68/EØF af 22/07/93 og efterfølgende ændringer. 2002/96/EF

Elektronisk programmeringsenhed

•• ••

Indstilling af uret

 Indstillingerne kan både foretage, når ovnen er slukket og når den er tændt, men ikke når der er programmeret et afslutningstidspunkt for tilberedningen. Efter tilslutning til el-nettet, eller efter

strømafbrydelse, blinker ikonet DISPLAYET blinker.

1. Tryk gentagne gange på tasten

og de fire cifre på DISPLAYET blinker.

2. med tasterne + og - indstilles klokkeslættet, og hvis man holder tasterne nede, skifter tallene hurtigere, så indstillingen gøres nemmere.

3. vent 10 sekunder, eller tryk igen på tasten at gemme indstillingen.

Indstilling af minuttælleren

 Denne funktion afbryder ikke tilberedningen og påvirker ikke brugen af ovnen. Den gør det kun muligt at aktivere et lydsignal, når det indstillede antal minutter er gået.

1. Tryk gentagne gange på tasten og de tre cifre på DISPLAYET blinker.

2. med tasterne + og - indstilles den ønskede

tid, og hvis man holder tasterne nede, skifter tallene hurtigere, så indstillingen gøres nemmere.

3. vent 10 sekunder, eller tryk igen på tasten

at gemme indstillingen. Herefter vises nedtællingen, indtil lydsignalet høres.

og de fire cifre på

, indtil ikonet

for

, indtil ikonet

for

Programmering af tilberedning

 Det er kun muligt at programmere tilberedningen, efter man har valgt et tilberedningsprogram.

Programmering af tilberedningsvarighed

1. Tryk gentagne gange på tasten og de tre cifre på DISPLAYET blinker.

2. med tasterne + og - indstilles den ønskede

varighed, og hvis man holder tasterne nede, skifter tallene hurtigere, så indstillingen gøres nemmere.

3. vent 10 sekunder, eller tryk igen på tasten

at gemme indstillingen.

4. Når tiden er gået, vises meddelelsen END på

DISPLAYET, ovnen afslutter tilberedningen og der udsendes et lydsignal.  Eksempel: Klokken er 9:00, og der programmeres

en tilberedningstid på 1 time og 15 minutter. Programmet standser automatisk kl. 10:15.

Programmering af afslutningstidspunkt for tilberedningen

 Programmering af afslutningstidspunktet for tilberedningen kan kun udføres, efter at man har indstillet varigheden.

1. Benyt samme fremgangsmåde som beskrevet

under punkt 1 til 3 for varigheden.

2. Tryk derefter gentagne gange på tasten

ikonet

3. med tasterne + og - indstilles tidspunktet for

afslutning af tilberedningen, og hvis man holder tasterne nede, skifter tallene hurtigere, så indstillingen gøres nemmere.

4. vent 10 sekunder, eller tryk igen på tasten

at gemme indstillingen.

5. Når tiden er gået, vises meddelelsen END på

DISPLAYET, ovnen afslutter tilberedningen og der udsendes et lydsignal.

De tændte ikoner en programmering. På DISPLAYET vises hhv. afslutningstidspunkt og varighed for tilberedningen.

Annullering af en programmering

Sådan annulleres en programmering:  tryk på tasten

der skal annulleres og cifrene på displayet blinker. Tryk på tasten -, indtil displayet viser cifrene 00:00.

 tryk og hold begge tasterne + og - nede

samtidig for at annullere alle programmeringer, også minuttællerne.

og de fire cifre på DISPLAYET blinker.

og viser, at der er foretaget

, indtil ikonet for indstillingen,

, indtil ikonet

for

, indtil

for

+ 39 hidden pages