Page 1
Operating Instructions
REFRIGERATOR/FREEZER COMBINATION
GB
English
FF187M
FF200M
Contents
Installation, 2-3
Positioning and connection
Reversible doors
Description of the appliance, 4-5
Control panel
Overall view
Start-up and use, 6-7-8
Starting the appliance
Navigating the display
No Frost Cooling system
Using the refrigerator to its full potential
Using the freezer to its full potential
Maintenance and care, 9
Switching the appliance off
Cleaning the appliance
Avoiding mould and unpleasant odours
Replacing the light bulb
Precautions and tips, 10
General safety
Disposal
Respecting and conserving the environment
GBGB
GB
GBGB
Troubleshooting, 11
Guarantee, 12
After Sales Service, 13
Page 2
Installation
! Before operating your new appliance, please read
GB
these operating instructions carefully. They contain
important information for safe use, installation and care
of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free
room.
2. Do not obstruct the airflow under and behind the
appliance. The compressor and condenser give off
heat and require good ventilation to operate correctly
and save energy.
3. Ensure the appliance is far away from any sources of
heat (direct sunlight, electric stove, etc.).
Electrical connections
After transportation of the appliance, carefully place it
vertically and wait at least 3 hours before connecting it
to the electricity mains. Before inserting the plug into the
electrical socket ensure the following:
• The appliance is earthed and the plug is compliant
with the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate
located on the bottom left side of the fridge (e.g. 150
W).
• The voltage must be in the range between the values
indicated on the data plate located on the bottom left
side (e.g. 220-240V, 50Hz).
• The socket is compatible with the plug of the
appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it (
Service
sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (
! The manufacturer declines any liability should these
safety measures not be observed.
). Do not use extension cords or multiple
see After Sales Service
see After Sales
Your appliance is supplied with a 13amp fused plug that
can be plugged into a 13amp socket for immediate use.
Before using the appliance please read the instructions
below.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
Replacing fuse covers:
When replacing a faulty fuse, a 13amp ASTA approved
fuse to BS 1362 should always be used and the fuse
cover re-fitted.
If the fuse cover is lost, the plug must not be used until
a replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking or the
colour that is embossed in words on the base of the plug.
Changing the plug:
Removing the plug
If your appliance has a non-rewireable moulded plug
and you should wish to remove it to add a longer cable
or to re-route the mains cable through partitions, units
etc. please ensure that either:
- The plug is replaced by a fused 13amp rewireable plug bearing the BSI mark of
approval.
or
- The mains cable is wired directly into a
13amp cable outlet, controlled by a
switch (in compliance with BS 5733)
which is accessible without moving the
appliance.
Disposing of the plug
Cut off and dispose of the supplied plug if it does not fit
your socket. The cable should be cut as close as
possible to the moulded plug.
Remove the fuse.
WARNING:
To avoid a shock hazard do not insert the discarded
plug into a socket anywhere else.
).
2
Page 3
Fitting a new plug
IMPORTANT
WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE...
Green and Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- Connect Green and Yellow wire to terminal marked
'E' or
- Connect Brown wire to terminal marked 'L' or
coloured red or brown.
- Connect Blue wire to terminal marked 'N' or
coloured Black or Blue.
If a 13amp plug (BS 1363) is used it must be
fitted with a 13amp fuse. A 15amp plug must be
protected by a 15amp fuse, either in the plug or adaptor
or at the distribution board.
:
or coloured Green and Yellow.
Reversible doors
GB
If it is necessary to change the direction in which the
doors open, please contact the Hotpoint Service
(see After Sales Service).
If you are in any doubt about the electrical
supply to your machine, consult a qualified
electrician before use.
CE Marking certifies that this appliance conforms to
the following EEC directives :
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC
& 93/68/EEC
3
Page 4
Description of the
appliance
GB
Control panel
REFRIGERATOR
Temperature
Adjustment
CHILD LOCK
REFRIGERATOR
status bar
FREEZER
status bar
ICE PARTY
FREEZER
Temperature
Adjustment
I CARE
ON/OFF
ALARMS
SUPER COOL
SUPER
FREEZE
HOLIDAY
ON/OFF
It is possible to switch the whole product (both the
refrigerator and freezer compartments) on by pressing
this button. The red LED indicates that the product is
switched off, while the green LED shows that it is
operating. To switch the product off, press and hold the
ON/OFF button for at least two seconds.
I CARE
This is used to activate and deactivate the I Care
function (the optimal temperature for energy saving
levels). When activated, the AUTO LED and the I Care
LED illuminate simultaneously.
ALARMS
This controls all the alarm signals connected to product
operation.
CHILD LOCK
Activates or deactivates the control panel button lock in
order to avoid the risk of the various functions being
activated accidentally by children.
REFRIGERATOR and Temperature Adjustment
Enable the temperature setting of the refrigerator to be
modified, with the relative confirmation of the
temperature selected shown on the display. It is also
possible to use these buttons to deactivate the
refrigerator compartment only.
(See also section “Troubleshooting”)
REFRIGERATOR status bar
Indicates the set temperature relating to the refrigerator
compartment or shows that it has been deactivated (in
this case the status bar is disabled).
FREEZER status bar
Shows the set temperature relating to the freezer
compartment.
SUPER COOL
Activates or deactivates the refrigerator SUPER COOL
function (rapid cooling). The SUPER COOL LED
illuminates.
SUPER FREEZE
Activates or deactivates the SUPER FREEZE function for
rapid freezing in the freezer compartment. The SUPER
FREEZE LED illuminates.
HOLIDAY
Activates or deactivates the HOLIDAY function (the
AUTO LED and HOLIDAY LED illuminates).
ICE PARTY
Activates or deactivates the ICE PARTY function (It
reduces the temperature of the freezer for the period of
time required to cool a bottle.). the ICE PARTY
illuminates.
FREEZER
Enable the temperature setting of the freezer to be
modified, with the relative confirmation of the
temperature selected shown on the display.
4
and Temperature Adjustment
Page 5
Overall view
The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not
directly represent the appliance purchased. For more complex features, consult the following pages.
LAMP
see Maintenance
(
)
Removable lidded
shelf with EGG TRAY
GB
SHELVES
WINE RACK
FRESH BOX
Compartment
FRUIT and
VEGETABLE bin
ICE CARE ice tray
FREEZER and
STORAGE
compartment
ICE CARE ice tray
*
Removable multipurpose
SHELVES
BOTTLE shelf
*
•
STORAGE
compartment
Levelling FEET
•
Varies by number and/or position.
Available only on certain models.
*
5
Page 6
Start-up and use
SHELVES: with or without grill.
GB
FRESH BOX
Due to the compartment low temperature (the coldest
in the refrigerator) food can be stored for up to one
week. It can also be used to store chilled ready meals.
(always read the instructions on the food packaging).
WINE RACK:
Use to store bottles of wine. The air circulates freely
between the bottles.
1
2
:
*
Due to the special guides the
shelves are removable and the
height is adjustable (
diagram
of large containers and food.
Height can be adjusted without
complete removal of the shelf.
), allowing easy storage
see
Starting the appliance
! After transportation of the appliance, carefully place it in
an upright position and wait at least 3 hours before
connecting it to the electricity mains, to make sure it
operates as it should.
• Clean the inside of the refrigerator well using warm
water and bicarbonate of soda before placing food
inside it.
The appliance is fitted with an electronic motor
•
control system. The compressor motor will start
approximately 8 minutes after the appliance is first
switched on, or after any power interruptions. (e.g.
power failures)
Navigating the display and setting the
storage temperatures
To switch on the appliance, press the ON/OFF button
for more than two seconds.
The i-care setting should be automatically activated.
This is the optimal setting for energy saving with a
frozen food storage temperature of -18°C and
general refrigerator compartment temperature of +5°C.
Status bar and LED will indicate these temperatures.
AUTO will be displayed.
On first switch on, we recommend that the SUPER
FREEZE function is also pressed (the status bar will
continue to display the freezer compartment set value).
This accelerates the cooling process of the freezer.
Once the optimum temperature is reached the function
will be automatically de-activate and frozen food can
be placed in the compartment.
Also,on first switch on, we recommend the SUPER
COOL function is pressed
to accelerate the cooling of the refrigerator
compartment. (The status bar will continue to show the
refrigerator compartment set value). After a few hours
the the SUPER COOL function will automatically
de-activate, and the refrigerator will be cool enough for
food to be placed inside.
When temperatures have stabilised on i-care setting, it
is normal that some sections of the refrigerator will
be warmer than 5°C (e.g. fruit and vegetable bin) and
some areas colder (e.g. fresh box).
Available only on certain models.
*
6
Page 7
When the i-care function is active, only slight
adjustments can be made to the temperature settings.
The freezer can be adjusted only colder, from -18°C to
-19°C or -20°C.
The refrigerator can be adjusted slightly colder or
warmer from a general +5°C to either +4° or +6°C.
If it is necessary to make these adjustments, hold down
the i-care button and use the
adjustment buttons for either the freezer or refrigerator
compartment.
The i-care setting can be de-activated by pressing the
corresponding button (see Control Panel).
(Note also that i-care will automatically be de-activated
if certain other buttons are pressed, see below).
Then, it is possible to make larger adjustments to the
compartment temperatures using any of the available
settings on the display for the refrigerator and freezer.
The set temperatures may not be achieved in all
conditions, but try adjusting the setting warmer
or colder (as necessary). The actual stored
food temperature can be affected by food loading,
number of door openings and by extreme ambient
conditions (very cold or very warm locations).
To activate and de-activate other functions simply press
the relevant button and the status will be shown by
the corresponding LED switching on or off.
The Holiday function minimises energy usage when on
holiday the set temperatures may not be adjusted.
The settings will automatically be +12°C for the
refrigerator and -18°C for the freezer.
AUTO and Holiday button will be illuminated.
Remember to remove perishable food.
To avoid setting conflicting operating modes, some
functions cannot be selected together.
Example: Super cool, super freeze, ice party, i-care
cannot be selected with Holiday mode.
The LEDs indicate the active function.
Press the Ice Party button when a wine bottle is
inserted in the freezer for chilling.
A buzzer will beep once and the Ice party LED light will
flash indicating the bottle must be removed.
Do not leave the bottle in the freezer because it will
freeze and this can cause the bottle to break.
Press the Ice Party button to cancel the LED .
and temperature
ALARMS.
! The freezer status bar is also used to indicate an
unusual temperature increase in the freezer
compartment. See Troubleshooting section for more
details about alarms and cancelling these.
Child Lock
In order to activate the Child Lock function, the Child Lock
button must be pressed for 2 seconds; the activation of the
button lock is confirmed by a short beep and the
illumination of the corresponding LED.
To deactivate the function, press the Child Lock button for 2
seconds; deactivation will be confirmed by a short beep
and by the corresponding LED switching off.
No Frost cooling system
This is recognisable by air
ducts located on the back
walls of each
compartment.
The No Frost system
circulates cold air
continuously to collect
humidity and prevent ice
and frost formation. The
system maintains an
optimal humidity level in the compartment, preserving
the original quality of the food, preventing the food from
sticking together and making defrosting a thing of the
past. Do not block the air circulation by placing food or
containers in direct contact with the rear ducts.
GB
7
Page 8
Using the refrigerator to its full potential
GB
• Adjust the temperature using the display.
• Press the SUPER COOL button (rapid cooling) to
lower the temperature quickly. For example, when you
place a large number of new food items inside a
fridge the internal temperature will rise slightly. The
function quickly cools the groceries by temporarily
reducing the temperature until it reaches the ideal
level.
• Place only cold or lukewarm foods in the compartment,
not hot foods (
see Precautions and tips
).
• Remember that cooked foods do not last longer than
raw foods.
• Do not store liquids in open containers. They will
increase humidity in the refrigerator and cause
condensation to form.
Using the freezer to its full potential
• Adjust the temperature using the display.
• To freeze foods safely and correctly, follow the
instructions below: place the food in the FREEZER
and STORAGE compartment, making sure that it
does not come into contact with any food that has
already been frozen; press the rapid-freezing SUPER
FREEZE button (the corresponding LED lights up)
and close the door. The function deactivates
automatically after 24 hours or when the inside of the
compartment has reached the optimal temperature
(the LED switches off).
ICE CARE tray
The fact that they are situated on the top part of the
freezer drawers ensures greater cleanliness: the ice no
longer comes into contact with the food placed inside
the freezer compartment; furthermore, the dripping of
the water during filling is avoided (a lid to cover up the
hole after filling with water is also provided).
1. Pull out the tray by pushing it up.
Check that the tray is completely empty and fill it with
water through the opening provided.
2. Take care not to exceed the level indicated (MAX
WATER LEVEL). Excess water prevents the ice cubes
from dispensing (if this happens, wait for the ice to
melt and empty the tray).
3. Turn the tray 90°: due to the connected compartments
each mould fills with water (
see diagram
).
4. Close the opening with the lid provided and put the
tray back, placing the top part in the corresponding
housing and allowing it to drop in again.
5. When the ice has formed (minimum time
approximately 8 hours) knock the tray against a hard
surface and warm the outside so that the ice cubes
come loose and take them out through the opening.
MAX
WATER LEVEL
• Do not re-freeze food that is defrosting or that has
already been defrosted. These foods must be cooked
and eaten (within 24 hours).
• Fresh food that needs to be frozen must not come into
contact with food that has already been defrosted.
• Do not place glass bottles which contain liquids, and
which are corked or hermetically sealed in the freezer
because they could break.
• The maximum quantity of food that may be frozen daily
is indicated on the data plate located inside one of the
compartments (for example: Kg/24h: 4).
! Do not open the freezer door during freezing.
! If there is a power cut or malfunction, do not open the
freezer door. This will help maintain the temperature inside
the freezer, ensuring that foods are conserved for at least
9 -14 hours.
8
WATER LEVEL
MAX
WATER LEVEL
MAX
Page 9
Maintenance and care
Switching the appliance off
During cleaning and maintenance it is necessary to
disconnect the appliance from the electricity supply:
1. Press and hold the ON/OFF button for approximately
two seconds, until everything on the display switches
off apart from the red LED corresponding to the ON/
OFF button.
2. pull the plug out of the socket
!
If this procedure is not followed, the alarm may sound.
This alarm does not indicate a malfunction. To restore
normal operation, it is sufficient to hold the ON/OFF
button down for more than two seconds. To disconnect
the appliance, follow points 1 and 2.
Cleaning the appliance
• The external and internal parts, as well as the rubber
seals may be cleaned using a sponge that has been
soaked in lukewarm water and bicarbonate of soda or
neutral soap. Do not use solvents, abrasive products,
bleach or ammonia.
• The removable accessories may be soaked in warm
water and soap or dishwashing liquid. Rinse and dry
them carefully.
• The back of the appliance may collect dust which can
be removed by delicately using the hose of a vacuum
cleaner set on medium power. The appliance must be
switched off and the plug must be pulled out before
cleaning the appliance.
Replacing the light bulb
GB
To replace the light bulb in the refrigerator
compartment, pull out the plug from the electrical
socket. Follow the instructions below.
Access the light bulb by removing the cover as
indicated in the diagram.
Replace it with a similar light bulb within the power
range indicated on the cover (10W).
Avoiding mould and unpleasant odours
• The appliance is manufactured with hygienic materials
which are odour free. In order to maintain an odour free
refrigerator and to prevent the formation of stains, food
must always be covered or sealed properly.
• If you want to switch the appliance off for an extended
period of time, clean the inside and leave the doors
open.
9
Page 10
Precautions and tips
! The appliance was designed and manufactured in
GB
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
This appliance complies with the following
Community Directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and
subsequent amendments;
-89/336/EEC of 03.05.89 (Electromagnetic
Compatibility) and subsequent amendments;
- 2002/96/CE..
General safety
• The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial
use.
• The appliance must be used to store and freeze food
products by adults only and according to the
instructions in this manual.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• Do not touch the appliance with bare feet or with wet or
moist hands and feet.
• Do not touch the internal cooling elements: this could
cause skin abrasions or frost/freezer burns.
• When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
• Before cleaning and maintenance, always switch off the
appliance and disconnect it from the electrical supply. It
is not sufficient to set the temperature adjustment knobs
control panel on OFF (appliance off) to eliminate all
electrical contact..
• In the case of a malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance.
Do not use utensils other than the scraper provided,
•
or electrical equipment which is not of the type
specified by the manufacturer, inside the frozen food
storage compartments.
Disposal
• Observe local environmental standards when
disposing packaging material for recycling purposes.
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on
human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the
appliance it must be separately collected. Consumers
should contact their local authority or retailer for
information concerning the correct disposal of their
old appliance.
Respecting and conserving the
environment
• Install the appliance in a fresh and well-ventilated
room. Ensure that it is protected from direct sunlight
and do not place it near heat sources.
• Try to avoid keeping the door open for long periods or
opening the door too frequently in order to conserve
energy.
• Do not fill the appliance with too much food:
cold air must circulate freely for food to be preserved
properly. If circulation is impeded, the compressor will
work continuously.
• Do not place hot food directly into the refrigerator. The
internal temperature will increase and force the
compressor to work harder and will consume more
energy.
• Regularly check the door seals and wipe clean to
ensure they are free of debris and to prevent cold air
from escaping (
see Maintenance
).
• Do not put ice cubes taken directly from the freezer into
your mouth.
• Do not allow children to tamper with the controls or play
with the appliance. Under no circumstance should they
be allowed to sit on the bins or to hang from the door.
• Keep packaging material out of the reach of children! It
can become a choking or suffocation hazard.
10
Page 11
Troubleshooting
Malfunctions:
The display is completely switched off.
The motor does not start.
The alarm sounds, the freezer status
bar LEDs light up in sequence, the
ALARM LED lights up and the
refrigerator compartment light
flashes.
The alarm sounds, the ALARM LED
lights up and the freezer status bar
LEDs light up in sequence.
The alarm sounds, the ALARM LED
flashes and the freezer status bar
LEDs flash simultaneously.
Possible causes / Solutions:
• The plug has not been inserted into the electrical socket, or not far enough
to make contact, or fuse in plug may have blown or there is no power in the
house.
• The appliance comes with a motor protection control (
• The refrigerator door has been open for more than two minutes.
The buzzer stops when the door is closed or when the ALARM button is
pressed.
• The temperature inside the freezer is too high.
The freezer will try to maintain a temperature of approximately 0°C so that
the food will not refreeze, allowing you to eat it within 24 hours or to
refreeze it after it has been cooked.
To switch off the buzzer, press the ALARM button. Press a second time to
display the set value on the freezer status bar, switch off the ALARM LED
and restore normal operation.
• The temperature of the freezer is dangerously high: the food inside must not
be eaten. The freezer will try to maintain a temperature of approximately 0°C.
To switch off the buzzer, press the ALARM button. Press a second time to
display the set value on the freezer status bar, switch off the ALARM LED and
restore normal operation.
see Start-up and use
).
GB
The refrigerator and the freezer are not
cold enough.
The food inside the refrigerator is
beginning to freeze.
The motor runs continuously.
The appliance makes a lot of noise.
Early ending of functions
• The doors do not close properly or the seals are damaged.
• The doors are opened too frequently.
• The temperature that has been set is too high (
• The refrigerator or the freezer have been over-filled.
• The temperature has been set too low (
• The SUPER FREEZE button has been pressed (rapid freezing): the yellow
SUPER FREEZE light is on or flashing (
• The door is not closed properly or is continuously opened.
• The outside ambient temperature is very high.
• The appliance has not been installed on a level surface (
• The appliance has been installed between cabinets that vibrate and make
noise.
• The internal refrigerant makes a slight noise even when the compressor is
off. This is not a defect, it is normal.
• Some noise from the air circulating fan is normal
• Electrical disturbance on the network or brief interruptions of the power supply
see Start-up and use
see Description
see Start-up and use
).
).
see Installation).
).
11
Page 12
GB
12 Months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown
repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because
of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no
This guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
- The appliance is used only on the electricity or gas supply printed on the rating plate.
- The appliance has been used for normal domestic purposes only.
- The appliance has not been altered, serviced, maintained, dismantled, or otherwise
interfered with by any person not authorised by us.
- Any repair work must be undertaken by us or our appointed agent.
- Any parts removed during repair work or any appliance that is replaced become our property.
- The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
Guarantee
cost to you.
- Damage resulting from transportation, improper use, neglect or interference or as a result
of improper installation.
- Replacement of any consumable item or accessory . These include but are not limited to: plugs,
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
- Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR
NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you
registering your appliance with us and the parts being fitted by one of our authorised engineers. There
will be a charge for our engineer's time. To activate the extra parts warranty on your appliance, simply call
our registration line on 0870 6092094 (ROI 01 230 0800).
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense
of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 08709
088 088 (ROI 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service
Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where necessary, to arrange
for an engineer to call. If we cannot resolve the technical problem we will replace your machine or, if you
prefer, give you your money back.
12
Page 13
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its working life than us -
the manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100
fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08709 066 066
Republic of Ireland: 0818 313 413
www.hotpointservice.co.uk
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
GB
We supply a full range of genuine replacement parts as well as accessory products that protect and
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08709 077 077
Republic of Ireland: 0818 313 413
www.hotpointservice.co.uk
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee
you must register your appliance with us.
UK: 0870 6092094
Republic of Ireland: 01 230 0800
www.hotpointservice.co.uk
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to use
quality, recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. Please see section “Precautions and tips” for
details about disposal legislation. To minimise the risk of injury to children, remove the door, plug and cut the
mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can no
longer be plugged into a mains socket, and the door cannot be locked shut.
13
Loading...