Operating Instructions
HOB
|
|
|
|
|
|
|
|
|
|
|
|
|
Contents |
GB |
|
|
|
|
|
|
|
|
Warnings, 2 |
|
|
|
|
|
|
|
|
|
Installation, 3-5 |
|
|
|
|
|
|
|
GB |
|
Positioning |
|
|
|
|
Electrical connection |
|
English,1 |
|
|||
Description of the appliance, 6 |
|
|||
|
|
|
|
|
|
|
|
Control panel |
|
|
|
|
Extendable cooking zones |
|
|
|
|
Start-up and use, 7-9 |
|
|
|
|
Switching on the hob |
|
|
|
|
Switching on the cooking zones |
|
|
|
|
Switching off the cooking zones |
|
|
|
|
Power function |
|
|
|
|
Heating elements |
|
|
|
|
Control panel lock |
|
KSB 640 X |
Switching off the hob |
|
||
Practical advice on using the appliance |
|
|||
CBRB 640 X |
Safety devices |
|
||
|
|
|
Practical cooking advice |
|
|
|
|
Precautions and tips, 10 |
|
|
|
|
General safety |
|
|
|
|
Disposal |
|
|
|
|
Care and maintenance, 11 |
|
|
|
|
Switching the appliance off |
|
|
|
|
Cleaning the appliance |
|
|
|
|
Disassembling the hob |
|
|
|
|
Technical description of the models, 12 |
|
|
|
|
Guarantee, 13 |
|
|
|
|
After Sales Service, 14 |
|
|
us |
on |
|
|
24 |
||
phone 24 |
|||
your |
|||
|
24 |
|
|
Please08448activate |
|||
to |
guarantee |
WARNING
GB
• WARNING: The appliance and its accessible parts become hot during use.
• Care should be taken to avoid touching heating elements.
• Children less than 8 years of age shall be kept away unless continuously supervised.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not
be made by children without supervision.
• WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.
• NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.
• WARNING: Danger of fire: do not store items on the cooking surfaces.
• WARNING: If the surface in glassceramic is cracked, switch off the appliance to avoid the possibility of electric shock.
•Never use steam cleaners or pressure cleaners on the appliance.
•The appliance is not intended to be operated by means of an external timer or separate remote control system.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
2
Installation
!Before operating your new appliance please read this instruction booklet carefully. It contains important information concerning the safe operation, installation and maintenance of the appliance.
!Please keep these operating instructions for future reference. Pass them on to any new owners of the appliance.
Positioning
!Keep all packaging material out of the reach of children. It may present a choking or suffocation hazard (see Precautions and tips).
!The appliance must be installed by a qualified professional in accordance with the instructions provided. Incorrect installation may cause harm to people and animals or may damage property.
Built-in appliance
Use a suitable cabinet to ensure that the appliance functions properly.
•The supporting surface must be heat-resistant up to a temperature of approximately 100°C.
•If the appliance is to be installed above an oven, the oven must be equipped with a forced ventilation cooling system.
•Avoid installing the hob above a dishwasher: if this cannot be avoided, place a waterproof separation device between the two appliances.
•Depending on the hob you want to install, the cabinet must have the following dimensions (see figure):
|
|
590 |
|
48 |
|
|
|
|
|
|
520 |
|
|
|
1 |
|
|
|
- |
560 |
|
490 |
+/ |
+/- |
|
||
|
|
||
|
1 |
|
|
Ventilation
To allow adequate ventilation and to avoid overheating of the surrounding surfaces the hob should be positioned as follows:
•At a minimum distance of 40 mm from the back panel.
•So that a minimum distance of 20 mm is maintained between the installation cavity and the cabinet underneath.
•Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 600 mm
from the edge of the hob.
GB
min. 20 mm
mm5 COMPARTMENT
min. 40 mm
min. 20 mm |
5 mm |
FAN-ASSISTED |
OVEN |
min. 40 mm |
FRONT SIDE
OF HOB
SUPPORTING |
|
|
SURFACE |
30 |
|
|
40 |
UNDERSIDE
OF HOB
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
3
|
Fixing |
||
GB |
|||
The appliance must be installed on a perfectly level |
|||
|
|||
|
supporting surface. |
||
|
|||
|
Any deformities caused by improper fixing could affect |
||
|
the features and operation of the hob. |
||
|
The thickness of the supporting surface should be taken |
||
|
into account when choosing the length of the screws for |
||
|
the fixing hooks: |
||
|
• |
30 mm thick: 17.5 mm screws |
|
|
• |
40 mm thick: 7.5 mm screws |
Fix the hob as follows:
1.Use short flat-bottomed screws to fix the 4 alignment springs in the holes provided at the central point of each side of the hob.
2.Place the hob in the cavity, make sure it is in a central position and push down on the whole perimeter until the hob is stuck to the supporting surface.
3.For hobs with raised sides: After inserting the hob into its cavity, insert the 4 fixing hooks (each has its own pin) into the lower edges of the hob, using the long pointed screws to fix them in place, until the glass is stuck to the supporting surface.
!The screws for the alignment springs must remain accessible.
!In order to adhere to safety standards, the appliance must not come into contact with electrical parts once it has been installed.
!All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool.
Electrical connection
! The electrical connection for the hob and for any builtin oven must be carried out separately, both for safety purposes and to make extracting the oven easier.
Terminal board
On the lower part of the appliance there is a connection box for the different
types of electricity supply (the
picture is only an indication and
is not an exact representation of the purchased model).
Single-phase connection
The hob is equipped with a pre-connected electricity supply cable, which is designed for single-phase
connection. Connect the wires in accordance with the instructions given in the following table and diagrams:
Voltage and |
Electrical cable |
Wire connection |
|
mains frequency |
|||
|
|
||
|
|
|
|
230-240V 1+N ~ |
|
: yellow/green |
|
|
N: the two blue wires together |
||
220-240V 1+N ~ |
|
||
|
L: brown and black together |
||
50/60 Hz |
|
||
|
|
|
Other types of connection
If the mains supply corresponds with one of the following:
Voltage and mains frequency
•400V - 2+N ~ 50/60 Hz
•220-240V 3 ~ 50/60 Hz
•230-240V 3 ~ 50/60 Hz
•400V - 2+2N ~ 50/60 Hz
Separate the wires and connect them in accordance with the instructions given in the following table and diagrams:
Voltage and |
Electrical cable |
Wire connection |
|
mains frequency |
|||
|
|
||
400V - 2+N ~ |
|
: yellow/green; |
|
|
|
||
50/60 Hz |
|
N: the two blue wires |
|
|
|
||
230-240V 3 ~ |
|
together |
|
220-240V 3 ~ |
|
L1: black |
|
50/60 Hz |
|
L2: brown |
|
|
|
|
|
|
|
: yellow/green; |
|
400V - 2+2N ~ |
|
N1: blue |
|
50/60 Hz |
|
N2: blue |
|
|
|
L1: black |
|
|
|
L2: brown |
|
|
|
|
If the mains supply corresponds with one of the following:
Voltage and mains frequency
• 400V 3 - N ~ 50/60 Hz proceed as follows:
! The cable provided is not suitable for the following types of installation.
1.Use a suitable supply cable, H05RR-F or higher, with the right dimensions (cable cross section: 25 mm).
2.To open the terminal board, use a screwdriver as
a lever under the side tabs of the cover (see Terminal board picture).
3.Loosen the cable clamp screw and the terminal board screws in accordance with the type of connection required and position the connection supports as shown in the following table and diagrams.
4.Position the wires in accordance with the information given in the following table and diagrams and connect the appliance by tightening all the screws for the springs as much as possible.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
4
Voltage and |
Electrical connections |
Terminal board |
mains frequency |
||
|
|
|
400V 3-N ~ |
|
Three-phase 400 |
50/60 Hz |
|
|
|
|
|
|
|
|
5. Secure the power supply cable by fastening the cable clamp screw, then put the cover back on.
|
Phase |
Phase |
Phase |
|
|
1 |
2 |
3 |
Three-phase 400 |
|
|
|
|
|
|
|
5 |
4 |
|
Earth |
Neutral |
U-bolt |
|
|
|
|
connection support |
|
Connecting the electricity supply cable to the mains
If the appliance is being connected directly to the electricity mains an omnipolar switch must be installed with a minimum opening of 3 mm between contacts.
! The installer must ensure that the correct electrical connection has been made and that it is fully compliant with safety regulations.
Before connecting the appliance to the power supply, make sure that:
|
|
|
|
|
|
• The appliance is earthed and the plug is compliant |
GB |
||||
with the law. |
|||||
|
•The socket can withstand the maximum power of the appliance, which is indicated on the data plate located on the appliance itself.
•The voltage falls within the range of values indicated on the data plate.
•The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets.
!Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.
!The cable must not be bent or compressed.
!The cable must be checked regularly and replaced by authorised technicians only.
!The manufacturer declines any liability should these safety measures not be observed.
!Do not remove or replace the power supply cable for any reason. Its removal or replacement will void the warranty and the CE marking. INDESIT does not assume liability for accidents or damage arising from replacement/removal of the original power supply cable. Replacement can only be accepted when carried out by personnel authorised by INDESIT and using an original spare part.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
5