Hotpoint AQXL 169 User Manual
Instructions for Installation and Use
Washing machine
Model AQXL 169
Instruction booklet
WASHING MACHINE
GB
English, 1
AQXL 169
Contents
GB
Installation, 2-3-4-5
Unpacking and levelling
Connecting the water and electricity supplies
Technical data
Description of the machine, 6-7
Control panel
Running a wash cycle, 8
Programmes and options, 9
Table of Programmes
Wash options
Detergents and laundry, 10
Detergent
Preparing the laundry
Washing advice
Load-balancing system
Precautions and tips, 11
General safety
Disposal
Opening the door manually
Care and maintenance, 12
Shutting off the water and electricity supplies
Cleaning the machine
Cleaning the detergent dispenser
Drum maintenance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 13
Assistance, 14
1
Installation
Keep this instruction manual in a safe place for
GB
future reference. If the appliance is sold, given away
or moved, please ensure the manual remains with the
machine so that the new owner may benefit from the
advice contained within it.
Please read this instruction manual carefully it
contains important information regarding the safe
installation, use and maintenance of the appliance.
You will find the guarantee and other details relating to
the installation process in the bag containing this booklet.
Unpacking and levelling
Unpacking
1. Once the washing machine has been removed
from the packaging, check that it has not been
damaged during transportation.
If it has been damaged, contact the retailer and do
not proceed any further with the installation process.
2. Remove the four
protective screws and
the rubber bush with the
respective spacer,
situated on the rear of
the appliance.
NB:The plastic spacers
may fall down inside the
machine once the bolt
has been removed, and
will not interfere with the operation of the machine.
3. Close the holes using the plastic covers provided in
the bag.
4. Keep all the pieces; if the washing machine is
transported in future, the screws and spacers will
have to be replaced in order to avoid damaging the
inside of the machine.
Packaging materials should not be used as toys by
children.
Levelling
1. Position the washing machine on a level and sturdy
floor, without resting it against walls or cabinets.
If the appliance is levelled correctly it will be more
stable and much less likely to cause vibrations and
noise during the spin cycle.
If positioned on a fitted carpet or a rug, adjust the
feet in such a way as to allow room for air to circulate
and provide ventilation beneath the washing machine.
Connecting the water and electricity
supplies
Connecting the water inlet hose
Before connecting the inlet hose to the water supply, allow
the water to flow from the tap until it runs clear.
1. Connect the inlet hose
to the machine, by
screwing it into the cold
water inlet on the upper
right hand side of the
back of the machine (see
figure).
2. Place the seal A
(provided in the bag) on
the end of the inlet hose
and screw it to a cold
A
3. The hose should not be bent or compressed.
The water pressure at the tap must fall within the
values indicated in the Technical data table (see next
page).
If the inlet hose is not long enough, contact a
specialist store or an authorised technician.
water tap with a 3/4 gas
threaded connection (see
figure).
2. If the floor is uneven,
the feet of the appliance
may be adjusted until it
reaches a perfectly
horizontal position (the
angle of inclination must
not exceed 2 degrees).
2
Always use the new inlet hoses supplied with the
machine.
Connecting the drain hose
65 - 100 cm
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
the supply voltage is included within the values i
ndicated on the Technical details table
(on the next page);
the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
Your appliance is now supplied with a 13 amp fused
plug it can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
GB
The drain hose may be
connected to an
under-sink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends
have been taken off
the spigot.
If it is place over the
edge of a basin or sink
be sure the free end of
the hose should not be
underwater.
We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more
than 15cms (6 inches). If the hose is pushed down
too far, this may cause the machine to self -syphon
ie. continuously empty as it is filling.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
the socket is earthed and in compliance with the
applicable law;
the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (on the next page);
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words on
the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug
and you should wish to re-route the mains cable
through partitions, units etc., please ensure that
either:
the plug is replaced by a fused 13 ampere rewearable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with
BS 5733) which is accessible without moving the
appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured
in accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
3
As the colours of the wires in the lead may not
GB
correspond with the coloured markings identifyng
the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E
or coloured Green or Green & Yellow.
or
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or coloured
Black.
If a 13 amp plug (BS 1363) is used it must be fitted
with a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE NEUTRAL (N)
BROWN LIVE (L)
GREEN & YELLOW EARTH (E)
Disposing of the appliance:
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible
to the plug body and dispose of it as described
above.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
When the washing machine is installed, the mains
socket must be within easy reach.
Do not use extensions or multiple sockets.
The power supply cable must never be bent or
dangerously compressed.
The power supply cable must only be replaced by
an authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
4
Loading...