Hotpoint 7HPF 604 User Manual

Operating Instructions

HOB

						Contents
							GB
						Installation, 2-3
		GB		RS
						Positioning
						Electrical connections
	English, 1			, 7
						Description of the appliance, 4
						Overall view
						Precautions and tips, 5
						General safety
						Disposal
						Practical Advice on Using the Electric Hot Plates
						Maintenance and care, 6
						Switching the appliance off
						Cleaning the appliance
						Technical data
						Assistance

7HPF 604 RU/HA 7HPF 604 IX RU/HA

Installation

! Before operating your new appliance please read GB this instruction booklet carefully. It contains important

information for safe use, installation and care of the appliance.

! Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance.

Positioning

!Keep packaging material out of the reach of children. It can become a choking or suffocation hazard (see Precautions and tips).

!The appliance must be installed by a qualified professional according to the instructions provided. Incorrect installation may cause harm to people and animals or may damage property.

Fitting the appliance

It is possible to instal them next to furniture which is higher than the working board. For a correct installation of the cooking top the following precautions must be followed:

•Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 600 mm from the edge of the hob.

•Hoods must be installed according to their relative installation instruction manuals and at a minimum distance of 650 mm from the hob.

	600mm min.
700mmmin.	600mmmin.

•Place the wall cabinets adjacent to the hood at a minimum height of 420 mm from the hob (see figure).

•If the hob is installed beneath a wall cabinet, the latter must be situated at a minimum of 700 mm above the hob (see figure).

•The installation cavity should have the dimensions indicated in the figure.

Fastening hooks are provided, allowing you to fasten the hob to tops that are between 20 and 40 mm thick. To ensure the hob is securely fastened to the top, we recommend you use all the hooks provided.

55 mm

475 mm

555 mm

Hook fastening diagram

Hooking position		Hooking position
for top H=20 mm		for top H=30 mm

Front

Hooking position		Back
for top H=40 mm

! Use the hooks contained in the “accessory pack”

•Where the hob is not installed over a built-in oven, a wooden panel must be installed as insulation. This must be placed at a minimum distance of 20 mm from the lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of wood, or on a completely flat surface with an opening of at least 45 x 560 mm (see diagrams).

.	45	mm	.
mm
560

2

Where a hob is installed above an oven without a forced ventilation cooling system, adequate ventilation must be provided inside the cabinet by means of air holes through which air can pass (see figure).

Electrical connection

The electric hobs are supplied without power supply cable since the cable must be sized according to the type of electrical connection used (see attached connection diagram). Follow these steps to connect the cable:

•Open the terminal box by removing the screws "V" and opening the cover (see figure).

•Connect the wires as shown in the diagram.

•Fix the cable using the cable clamp "F", replace the cover and fasten it using the screws "V" (see figure).

V

380-400V 3N~ H05RR-F 5x1.5 CEI-UNEL 35363

380-400V 2N~ H05RR-F 4x1.5 CEI-UNEL 35363

220-230V 1N~ H05RR-F 3x2.5 CEI-UNEL 35363

	1	2	3	4	5
					F
1	2	3		4	5
R	S		T		N
1	2	3		4	5
	R	S N
1	2	3		4	5
			R		N

Connecting the supply cable to the mains

GB

Install a standardised plug corresponding to the load indicated on the data plate.

The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C.

!The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations.

Before connecting to the power supply, make sure that:

•The appliance is earthed and the plug is compliant with the law.

•The socket can withstand the maximum power of the appliance, which is indicated on the data plate.

•The voltage is in the range between the values indicated on the data plate.

•The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets.

!Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.

!The cable must not be bent or compressed.

!The cable must be checked regularly and replaced by authorised technicians only (see Assistance).

!The manufacturer declines any liability should these safety measures not be observed.

!If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier.

3

Description of the appliance

Overall view

GB

ELECTRIC PLATE

Control knobs for the cook-top

ELECTRIC PLATE

Pilot lamp of the

ELECTRIC PLATE

•The ELECTRIC PLATE vary in diameter and power: "normal" and "fast". The latter can be identified by a red boss in the center of the hot plate itself.

! The position of the corresponding electric hot plate is indicated on each control knob.

•The ELECTRIC PLATE ON indicator light switches on whenever the knob is moved from the 'off' position.

•The ELECTRIC PLATE control knob is a device used to regulate power.

The knob may be turned clockwise or anticlockwise and set to six different positions:

Setting	Normal or Fast Plate
0	Off
1	Low
2 - 5	Medium
6	High

! Please refer to the "Practical Advice on Using the Electric Hot Plates" section for a list of the relative positions and their recommended uses.

4