Hot Max 175WFG, 125WFG, 135WFG Operator's Manual

Operator’s Manual

Model 175WFG

Wire Feed Welder

MIG Welders

WARNING: Do not assemble, install, or operate this equipment without reading ALL of this manual
and the safety precautions and warnings illustrated in this manual.

KDAR Company Tel: [phone]

1 Mulch Lane Fax: [phone]
St. Louis, MO 63044 Web Site: www.hotmaxtorches.com

SAFETY PRECAUTIONS AND WARNINGS

PLEASE READ BEFORE USING EQUIPMENT

WARNING

ELECTRIC SHOCK CAN KILL.

 The input circuits are live and hot when the power is on
 Do not touch live electrical parts
 Wear dry, hole free insulated work gloves and body protection when operating
 Do not touch torch components if in contact with the work piece or ground
 Always turn off power before cleaning, checking, or changing parts
 Properly ground this piece of equipment per state and federal requirements
 Inspect and replace any worn or damaged torch cables or leads
 Keep all panels and covers securely in place
 Keep away from the torch tip and weld arc when trigger is pressed
 Ground the metal or work piece to the ground cable (Earth Clamp)
 Never dip the tip into water to cool or attempt to use welder in or under water
 This DC equipment holds a lot of power in the off position, before touching, make sure voltage is

near zero on input capacitors before touching any parts.

 Keep children away from this equipment

 Protect yourself and others from possible injury
 Pacemaker wearers should consult with their doctor before operating
 Read and follow all instructions in this manual before operating
 All installation, operation, and maintenance procedures are to be

performed only by qualified individuals

ARC RAYS CAN BURN SKIN AND EYES

 Arc rays when welding produce intense ultraviolet and infrared rays that can burn skin and eyes
 Wear face protection, either helmet or shield, when operating. ANSI Z49.1 approved shade #9

recommended for all cutting currents less than 300 amperes. The lens should conform to ANSI
Z87.1 standards for testing.

 Wear approved safety glasses with side shields under the face protection
 Warn others not to stare at the arc as it can cause damage to the eyes. Provide barriers to protect

other workers in the area from the arc while operating

 Wear flame resistant gloves, clothing, and shoes when operating

FUMES AND GASES CAN BE HAZARDOUS

 Arc welding produces fumes and gases and breathing these gases is hazardous to your health
 Keep your head out of the fumes and do not breath the fumes while welding
 Work only in a confined area if it has sufficient ventilation, or while wearing an air supplied

respirator. Fumes from welding deplete the oxygen supply and can be harmful. Always be sure
there is ample breathing air

 Read the MSDS sheets and the instructions from manufacturers for metals to be welded, coatings,

and cleaners

 Do not use the welder near hydrocarbon vapors coming from degreasing, cleaning, or spraying

operations. The heat and rays can react with solvent vapors to create the gas phosgene, a very toxic
gas and other irritating gases

 Do not weld coated metals, such as galvanized, lead, or cadmium plated steel. Before welding, all

plating must be removed. The area must be well ventilated or an air supplied hood must be used.
The coatings and chemicals when burned cause highly irritating and toxic fumes.

 Do not weld containers with toxic, flammable, or reactive elements stored in them. They must be

emptied and properly prepared before welding.

KDAR Company 1

WELDING SPARKS CAN CAUSE INJURY, FIRE, OR EXPLOSION

 Remove all flammable materials from the welding area
 Always have a charged fire extinguisher available in the welding area
 When not welding make sure the welding tip is not grounded, this causes a heat build up and

possible fire

 Avoid welding near hydraulic lines, fuel lines, electrical cords, air hoses, or welding guns and

cables

 Sparks and hot metal fly out from the work area when welding, wear approved safety glasses with

side shields under approved helmets, wear proper body and hand protection, and wear flame
resistant ear plugs to keep sparks from entering the ears

CYLINDERS CAN EXPLODE IF DAMAGED

 Gas cylinders contain gas under very high pressure. If damaged they can result in that cylinder ex-

ploding. Gas cylinders are a major part of metalworking and must be treated with care.

 Protect gas cylinders from excessive heat, mechanical shocks, slag, open flames, sparks, and arcs
 Always keep cylinders in an upright position securely fastened to a fixed support
 Valve protection caps should always be in place and hand tight except when the cylinder is in use
 Keep all cylinders away from any welding or electrical circuits
 Never allow the arc from a welder to contact a cylinder
 Never cut any type of pressurized cylinder, an explosion could result
 Always turn your face away from the valve when opening the cylinder
 Read and follow all instructions on compressed gas cylinders, associated equipment, and CGA pub-

lication P-1 listed in the Safety Standards before using

ELECTRIC AND MAGNETIC FIELDS MAY BE DANGEROUS

 Electric current used in arc welding can create Electro-Magnetic Fields (EMF)
 Magnetic fields can affect pacemakers and wearers should avoid proximity to EMF. Wearers need

to contact their doctors before operating this type of equipment

 Exposure to EMF during operation of this equipment may have other health effects which are not

yet known

 Route the work and torch cables together and not around your body
 Do not place your body between the torch cable and the ground cable. They both need to be on the

same side of your body when operating

 Do not work next to the welding machine

ELECTRICALLY POWERED EQUIPMENT

 Disconnect power source or turn off circuit breaker at the power panel before working on any

equipment

 Only install equipment using the US National Electrical Code, all local codes, and the man-

ufacturer’s recommendations

HOT PARTS CAN CAUSE SERIOUS BURNS

 Do not touch hot parts without wearing protection.
 Allow the torch to cool sufficiently before working with parts that could potentially be hot.

KDAR Company 2

NOISE CAN DAMAGE HEARING

 Prolonged noise exposure from welding equipment can cause damage if levels of noise exceed the

OSHA standards

 Wear approved hearing protectors
 Warn other workers nearby of the high noise level and hazard

CALIFORNIA PROPOSITION 65 WARNINGS

 Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause

birth defects, and in some cases, cancer. (California Health and Safety Code Section 25249.5 et seq.)

PRINCIPAL SAFETY STANDARDS

AMERICAN WELDING SOCIETY

 AWS C5.2, Recommended Practices for Plasma Arc Cutting
 AWS F4.1, Recommended Safe Practices for the Preparation for Welding and Cutting

OSHA STANDARDS

 OSHA 29 CFR 1910, Safety and Health Standards

NATIONAL FIRE PROTECTION ASSOCIATION

 NFPA Standard 70, National Electric Code
 NFPA Standard 51B, Cutting and Welding Processes

AMERICAN NATIONAL STANDARDS INSTITUTE

 ANSI Standard Z87.1, Safe Practices for Occupation and Educational Eye and Face Protection
 ANSI Standard Z49.1, Safety in Welding and Cutting

KDAR Company 3

Specifications

Rated input 230VAC, 60 hertz, 22 amps

Maximum output open-circuit voltage 35 volts DC

Rated output 130 AMPS@20volts 20%duty cycle

Wire feed rate 59 to 472 in/min (1.5-12m/min)

Specifications of applicable welding

wire

Welding Wire Spool 8”x2” (200mmx50mm)

Weight 54 lb (26 kg)

Dimensions (Length*Width*Height) 16”x9.6”x14.5” (408x244x367)

Features & Benefits

 Light weight, small size all steel case.
 Easy to use.
 MIG/MAG ready, regulator and 5’ hose in-

cluded.

 Optional spool gun available.
 Infinite output voltage level.
 Infinite wire feed speed control.
 Wire at gun is “cold” when not welding.
 Power on indicator light and overload indicator

light equipped.

 Fan cooled.
 20% duty cycle minimum.
 Welds 22 gauge to 3/8” with flux cored wire.
 Built in wire feeder with easy to use tension

adjustment lever.

 Dual size groove drive roller to fit sizes .23”

to .35” wire (.6 to .9 mm).

.025”-.030” (0.6-0.8mm) solid steel

.030”-.035” (0.8-0.9mm) Flux-Cored

4”x2” (100mmx50mm)

Table 1

 Easy polarity change for switching to and from

gas.

 Flux covered (FCAW) set up from the factory,

ready to weld.

 Welds steel, aluminum, and stainless (special

gas required for aluminum and stainless).

 2 year limited warranty on the machine.
 90 day limited warranty on gun and hose.
 Comes with the following components.

 2 replacement tips
 Hex wrench to change wire feed roller.
 Gas nozzle for MIG welding.

 10# spool adaptor.
 Gas regulator
 5’ gas hose
 2# Spool .030” Flux Core Wire

KDAR Company 4

Safety Considerations

Warning

Electric Shock Can Kill

 Only qualified personnel should attempt to install this equipment.
 Turn off the input power at the power panel or disconnect switch and discharge

capacitors before working inside the equipment.

 Take care not to touch electrically hot parts
 Make sure the unit is switched off before plugging it into a the power outlet.

Package Contents

Installation/Setup

KDAR Company 5