Hotel Fitness Xt9700, HF-XT9700.0 User Manual
Model No. HF-XT9700.0
Serial No.
The serial number is found in the
location shown below. Write the
serial number in the space above.
Serial
Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, please see
HOW TO CONTACT CUSTOMER
CARE on the back cover of this
manual.
USER'S MANUAL
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
www.HotelFitness.com
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
OW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
H
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
HOW TO CONTACT CUSTOMER CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible,
see the back cover of this manual and
request a free replacement decal. Apply the
decal in the location shown. Note: The
decal(s) may not be shown at actual size.
HOTEL FITNESS is a registered trademark of Hotel Fitness Club, Inc.
FREEMOTION is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: T
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. Hotel Fitness and FreeMotion Fitness assume no responsibility for personal injury or
property damage sustained by or through the use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
2. Use the elliptical exerciser only as described
in this manual.
3. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
4. Keep the elliptical exerciser indoors, away
from moisture and dust. Place the elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet. Make
sure that there is at least 3 ft. (0.9 m) of clearance in the front and rear of your elliptical
exerciser and 2 ft. (0.6 m) on each side.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 350 lbs.
(159 kg).
o reduce the risk of serious injury, read all important precautions and
8. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the elliptical exerciser. Always
wear athletic shoes for foot protection while
exercising.
9. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
elliptical exerciser.
10. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determining heart rate trends in general.
11. Keep your back straight while using the elliptical exerciser; do not arch your back.
12. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
13. When you stop exercising, allow the pedals
to slowly come to a stop.
3
BEFORE YOU BEGIN
Thank you for selecting the revolutionary HOTEL
ITNESS
F
elliptical exerciser provides an impressive selection of
features designed to help you achieve your fitness
goals.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the back
®
T9700 elliptical exerciser. The XT9700
X
Upper Body Arm
Handgrip Pulse Sensor
Water Bottle Holder*
cover of this manual. To help us assist you, note the
roduct model number and serial number before con-
p
tacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Pedal
Handle
Leveling Foot
Wheel
Leveling Foot
*Water bottle is not included
4
M8 Locknut
(72)–4
M4 x 19mm
Screw (57)–2
M10 Split
Washer (85)–6
M10 Washer
(67)–6
M8 Small
Washer (18)–4
M8 Washer
(69)–4
M8 x 55mm Bolt
Set (92)–2
M10 x 123mm Button Bolt (38)–2
M8 x 38mm Button
Bolt (58)–4
Wave Washer
(88)–4
M10 Locknut
(70)–2
M4 x 16mm
Screw (47)–6
Thrust Washer
(66)–4
M10 x 13mm Button
Screw (54)–6
M10 x 65mm Bolt
Set (94)–2
M8 x 19mm Button
Screw (56)–4
M10 x 25mm Patch
Screw (48)–6
ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires a Phillips screwdriver , an
djustable wrench , and a rubber mallet .
a
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The
number following the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware
kit, check to see if it has been preassembled.
5
1.
To make assembly easier, read the
information on page 5 before you begin.
ttach the Stabilizer (8) to the Frame (1) with
A
two M10 x 123mm Button Bolts (38) and two
M10 Locknuts (70).
Tighten two Leveling Feet (36) into the underside of the Stabilizer (8).
1
38
8
2. Have another person hold the Upright (2) in the
position shown. Connect the Upper Wire
Harness (77) to the Lower Wire Harness (78).
Tip: Avoid pinching the wires. Attach the
Upright (2) to the Frame (1) with four M10 x
25mm Patch Screws (48) and four M10 Split
Washers (85).
2
Avoid pinching
the wires
36
1
70
2
77
78
48
85
85
48
1
85
6
3. Attach the Track Frame (4) to the Frame (1) with
two M10 x 25mm Patch Screws (48) and two
M10 Split Washers (85). Tip: Finger tighten a
atch Screw into the lower hole first, and
P
then finger tighten a Patch Screw into the
pper hole. Then, tighten both Patch Screws.
u
Tip: This step may be easier if you raise the
Frame (1) a few inches in the location shown
by the arrow at the right while you attach the
Track Frame (4).
See the inset drawing. Tighten two Leveling
Feet (36) into the underside of the Track Frame
(4).
3
48
1
85
85
48
4
4
4. Apply a small amount of the included grease to
the sides of two Wave Washers (88) and two
Thrust Washers (66).
Slide a Weld Spacer (89) onto the left Crank
Arm (83). Next, identify the Left Track Arm (12),
which is marked with an “L.”
Orient the Left Track Arm (12) as shown, and
slide it onto the left Crank Arm (83). Then, slide
a Wave Washer (88) on the end of the left Crank
Arm.
Slide an M8 Small Washer (18) and an Axle Cap
(41) onto an M8 x 19mm Button Screw (56).
Next, slide a Thrust Washer (66) onto the shoulder of the Axle Cap. Then, tighten the Button
Screw into the end of the left Crank Arm (83).
Make sure that the Thrust Washer remains
on the shoulder of the Axle Cap, and that the
Wave Washer (88) remains on the end of the
left Crank Arm.
36
4
83
Grease
11
89
88
66
18
41
56
12
Repeat this step to attach the Right Track
Arm (11).
7
5. Attach a Pedal (21) to the Left Pedal Leg (14)
with three M10 x 13mm Button Screws (54) and
three M10 Washers (67). Make sure that the
utton Screws are in the indicated holes.
B
The other holes in the Left Pedal Leg are not
sed.
u
Attach the other Pedal (not shown) to the
Right Pedal Leg (not shown) in the same
way.
5
1
2
14
67
67
6. Apply a thin film of grease to the barrel of an
M10 x 65mm Bolt Set (94).
Fit the bracket on the Left Pedal Leg (14) onto
the bracket on the Left Track Arm (12). Attach
the Left Pedal Leg to the Left Track Arm with the
M10 x 65mm Bolt Set (94).
Attach the Right Pedal Leg (not shown) to
the Right Track Arm (not shown) in the same
way.
54
54
6
94
14
Grease
94
12
8
7. Identify the Left Upper Body Arm (19), which is
marked with an “L.”
nsert the Left Upper Body Arm (19) into one of
I
the Upper Body Legs (17). Next, turn the Left
pper Body Arm and the Upper Body Leg so
U
that the wide side of the pivot tube on the
Left Upper Body Arm is above the hexagonal
holes in the Upper Body Leg.
Attach the Left Upper Body Arm (19) with two
M8 x 38mm Button Bolts (58) and two M8
Locknuts (72). Make sure that the Locknuts
are inside the hexagonal holes. Do not
tighten the Button Bolts yet.
Assemble the Right Upper Body Arm (20)
and the other Upper Body Leg (17) in the
same way.
7
19
ide side of
W
20
pivot tube
58
72
58
Hexagonal
Holes
17
17
8. Apply a small amount of grease to the sides of
two Wave Washers (88) and two Thrust
Washers (66).
Slide the Left Upper Body Arm (19) onto the
Pivot Axle (16) as shown. Next, slide a Wave
Washer (88) onto the end of the Pivot Axle.
Slide an M8 Small Washer (18) and an Axle Cap
(41) onto an M8 x 19mm Button Screw (56).
Next, slide a Thrust Washer (66) onto the shoulder of the Axle Cap. Then, tighten the Button
Screw a few turns into the end of the Pivot Axle
(16). Make sure that the Thrust Washer
remains on the shoulder of the Axle Cap, and
that the Wave Washer (88) remains on the
end of the Pivot Axle.
Assemble the Right Upper Body Arm (20) in the
same way. Then, tighten both M8 x 19mm
Button Screws (56) at the same time.
8
20
19
16
66
56
18
18
56
66
88
41
88
Grease
1
41
Grease
9
Loading...