Hoshizaki KM-1400SWH-3-M User Manual
Hoshizaki
Hoshizaki America, Inc.
Modular Crescent Cuber
Models
KM-1400SWH/3-M
“A Superior Degree
of Reliability”
www.hoshizaki.com
INSTRUCTION MANUAL
™
Issued: 5-26-2010
IMPORTANT
Only qualied service technicians should install, service, and maintain the
icemaker. No installation, service, or maintenance should be undertaken until
the technician has thoroughly read this Instruction Manual. Likewise, the owner/
manager should not proceed to operate the icemaker until the installer has
instructed them on its proper operation. Failure to install, operate, and maintain
the equipment in accordance with this manual may adversely affect safety,
performance, component life, and warranty coverage.
Hoshizaki provides this manual primarily to assist qualied service technicians in the
installation, maintenance, and service of the icemaker.
Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call, write, or send an e-mail message to the Hoshizaki Technical
Support Department for assistance.
HOSHIZAKI AMERICA, INC.
618 Highway 74 South
Peachtree City, GA 30269
Attn: Hoshizaki Technical Support Department
Phone: 1-800-233-1940 Technical Support
(770) 487-2331
Fax: 1-800-843-1056
(770) 487-3360
E-mail: techsupport@hoshizaki.com
Web Site: www.hoshizaki.com
NOTE: To expedite assistance, all correspondence/communication MUST include the
following information:
• Model Number
• Serial Number
• Complete and detailed explanation of the problem.
2
IMPORTANT
This manual should be read carefully before the icemaker is installed and
operated. Only qualied service technicians should install, service, and
maintain the icemaker. Read the warnings contained in this booklet carefully as
they give important information regarding safety. Please retain this booklet for
any further reference that may be necessary.
CONTENTS
Important Safety Information ................................................................................................. 4
I. Specications ...................................................................................................................... 5
A. Nameplate Rating ......................................................................................................... 5
1. KM-1400SWH-M (water-cooled marine) .................................................................. 5
2. KM-1400SWH3-M (water-cooled marine) ................................................................ 6
B. Dimensions/Connections .............................................................................................. 7
II. Installation and Operating Instructions .............................................................................. 8
A. Checks Before Installation ............................................................................................. 8
B. How to Remove Panels ................................................................................................. 8
C. Location ........................................................................................................................ 9
D. Setup ............................................................................................................................. 9
E. Installation of Second Unit ...........................................................................................11
F. Electrical Connection ................................................................................................... 13
G. Water Supply and Drain Connections ......................................................................... 14
1. Icemaker ................................................................................................................ 14
2. Water-Cooled Condenser....................................................................................... 15
a) Connection to an Open Drain System ................................................................ 15
b) Connection to a Closed Loop System ................................................................ 16
H. Final Checklist ............................................................................................................. 17
I. Startup .......................................................................................................................... 18
III. Cleaning and Maintenance ............................................................................................. 19
A. Cleaning & Sanitizing Instructions............................................................................... 19
1. Cleaning Procedure ................................................................................................ 20
2. Sanitizing Procedure - Following Cleaning Procedure ........................................... 21
B. Maintenance ................................................................................................................ 22
C. Preparing the Icemaker for Long Storage ................................................................... 22
3
Important Safety Information
Throughout this manual, notices appear to bring your attention to situations which could
result in death, serious injury, or damage to the unit.
WARNING Indicates a hazardous situation which could result in death or
serious injury.
CAUTION Indicates a situation which could result in damage to the unit.
IMPORTANT Indicates important information about the use and care of the
unit.
WARNING
This icemaker should be destined only to the use for which it has been
expressly conceived. Any other use should be considered improper and
therefore dangerous. The manufacturer cannot be held responsible for eventual
damage caused by improper, incorrect, and unreasonable use.
To reduce the risk of death, electric shock, serious injury, or re, follow
basic precautions including the following:
• Electrical connection must be hard-wired and must meet international,
national, state, and local electrical code requirements. Failure to meet these
code requirements could result in death, electric shock, serious injury, re, or
severe damage to equipment.
• This unit requires an independent power supply. See the nameplate for proper
voltage and breaker/fuse size. Failure to use a proper breaker or fuse can
result in a tripped breaker, blown fuse, or damage to existing wiring. This
could lead to heat generation or re.
• THIS UNIT MUST BE GROUNDED. Failure to properly ground this unit could
result in death or serious injury.
• This unit should be disassembled or repaired only by qualied service
personnel to reduce the risk of electric shock, injury, or re.
• Do not make any alterations to the unit. Alterations could result in electric
shock, injury, re, or damage to the unit.
4
I. Specications
HOSHIZAKI ICE MAKER
A. Nameplate Rating
1. KM-1400SWH-M (water-cooled marine)
MODEL NUMBER KM-1400SWH-M
SERIAL NUMBER
AC SUPPLY VOLTAGE 208-230/60/1 (2 WIRE)
COMPRESSOR 208-230V 8.2RLA 56LRA
PUMP 120V 1.2FLA 60W
FAN --- --- --OTHER 115-120V 0.3A
MAXIMUM FUSE SIZE 15 AMPS
MAX. HACR BREAKER(USA ONLY) 15 AMPS
MAX. CIRC. BREAKER (CANADA ONLY) 15 AMPS
MINIMUM CIRCUIT AMPACITY 15 AMPS
DESIGN PRESSURE HI-427PSI LO-230PSI
REFRIGERANT 404A 2 LB. 2.4 OZ.
MOTOR-COMPRESSOR THERMALLY PROTECTED,
NOT INTENDED FOR OUTDOOR USE!
Hoshizaki America, Inc.
Peachtree City, GA
www.hoshizaki.com
ICE MAKER
WITHOUT
STORAGE
MEANS
45FE
COMPONENT
See the nameplate for electrical and refrigeration specications. This nameplate is located
on the rear panel.
Since this nameplate is located on the rear panel of the icemaker, it cannot be read when
the back of the icemaker is against a wall or against another piece of kitchen equipment.
Therefore, the necessary electrical and refrigeration information is also on the rating label,
which can be easily seen by removing only the front panel of the icemaker.
We reserve the right to make changes in specications and design without prior notice.
5
HOSHIZAKI ICE MAKER
2. KM-1400SWH3-M (water-cooled marine)
MODEL NUMBER KM-1400SWH3-M
SERIAL NUMBER
AC SUPPLY VOLTAGE 208-230/60/3
COMPRESSOR 208-230V 5.7RLA 51LRA
PUMP 120V 1.2FLA 60W
FAN --- --- --OTHER 115-120V 0.3A
MAXIMUM FUSE SIZE 15 AMPS
MAX. HACR BREAKER(USA ONLY) 15 AMPS
MAX. CIRC. BREAKER (CANADA ONLY) 15 AMPS
MINIMUM CIRCUIT AMPACITY 15 AMPS
DESIGN PRESSURE HI-427PSI LO-230PSI
REFRIGERANT 404A 2 LB. 2.4 OZ.
MOTOR-COMPRESSOR THERMALLY PROTECTED,
NOT INTENDED FOR OUTDOOR USE!
Hoshizaki America, Inc.
Peachtree City, GA
www.hoshizaki.com
ICE MAKER
WITHOUT
STORAGE
MEANS
45FE
COMPONENT
See the nameplate for electrical and refrigeration specications. This nameplate is located
on the rear panel.
Since this nameplate is located on the rear panel of the icemaker, it cannot be read when
the back of the icemaker is against a wall or against another piece of kitchen equipment.
Therefore, the necessary electrical and refrigeration information is also on the rating label,
which can be easily seen by removing only the front panel of the icemaker.
We reserve the right to make changes in specications and design without prior notice.
6
B. Dimensions/Connections
1. KM-1400SWH/3-M (water-cooled marine)
Unit: (mm) in.
Note: When used with a storage bin not recommended by Hoshizaki, the icemaker
needs the space at the bottom opening as in the illustration.
7
II. Installation and Operating Instructions
WARNING
1. This icemaker must be installed in accordance with applicable international,
national, state, and local regulations.
2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews
are securely in place after installation. Make sure that none have fallen into
the storage bin.
A. Checks Before Installation
• Visually inspect the exterior of the shipping container and immediately report any
damage to the carrier. Upon opening the container, any concealed damage should also
be immediately reported to the carrier.
• Remove the shipping carton, tape, and packing material. If any are left in the icemaker,
it will not work properly.
• Remove the panels to prevent damage when installing the icemaker. See "II.B. How to
Remove Panels."
• Remove the package containing the accessories.
• Remove the protective plastic lm from the panels. If the icemaker is exposed to the sun
or to heat, remove the lm after the icemaker cools.
• Check that the refrigerant lines do not rub or touch lines or other surfaces.
• Check that the compressor is snug on all mounting pads.
• See the nameplate on the rear panel, and check that your voltage supplied corresponds
with the voltage specied on the nameplate.
• This icemaker can be installed on a storage bin 48" wide or wider. For options, contact
your local Hoshizaki distributor.
B. How to Remove Panels
See Fig. 1
• Front Panel: Remove the 2 screws. Lift up
and towards you.
• Top Panel: Remove the 2 screws, and
then lift off.
• Side Panel (R): Remove the screw. Slide
forward slightly and lift off.
• Insulation Panel: Remove the
thumbscrew. Lift up slightly and pull
towards you.
• Top Insulation: Lift off.
Top
Insulation
Insulation
Panel
Front Panel
Top Panel
Side Panel (R)
Fig. 1
8
Loading...