Hoshizaki C-101BAH, C-101BAH-DS, C-101BAH-AD, C-101BAH-ADDS Installation Manual
Hoshizaki America, Inc.
Hoshizaki
Self-Contained Cubelet
Models
C-101BAH
C-101BAH-DS
“A Superior Degree
of Reliability”
www.hoshizaki.com
C-101BAH-AD
C-101BAH-ADDS
INSTRUCTION MANUAL
Issued: 7-25-2013
WARNING
Only qualied service technicians should install and service the appliance. To
obtain the name and phone number of your local Hoshizaki Certied Service
Representative, visit www.hoshizaki.com. No installation or service should be
undertaken until the technician has thoroughly read this Instruction Manual.
Likewise, the owner/manager should not proceed to operate the appliance until the
installer has instructed them on its proper operation. Failure to install, operate, and
maintain the appliance in accordance with this manual will adversely affect safety,
performance, component life, and warranty coverage and may result in costly water
damage. Proper installation is the responsibility of the installer. Product failure or
property damage due to improper installation is not covered under warranty.
Hoshizaki provides this manual primarily to assist qualied service technicians in the
installation, maintenance, and service of the appliance.
Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call, send an e-mail message, or write to the Hoshizaki Technical
Support Department for assistance.
Phone: 1-800-233-1940; (770) 487-2331
Fax: 1-800-843-1056; (770) 487-3360
E-mail: techsupport@hoshizaki.com
HOSHIZAKI AMERICA, INC.
618 Highway 74 South
Peachtree City, GA 30269
Attn: Hoshizaki Technical Support Department
NOTE: To expedite assistance, all correspondence/communication MUST include the
following information:
• Model Number
• Serial Number
• Complete and detailed explanation of the problem.
2
IMPORTANT
This manual should be read carefully before the appliance is installed and operated.
Read the warnings and guidelines contained in this manual carefully as they
provide essential information for the continued safe use and maintenance of the
appliance. Retain this manual for any further reference that may be necessary.
CONTENTS
Important Safety Information ................................................................................................. 4
I. Specications ...................................................................................................................... 6
A. Construction .................................................................................................................. 6
B. Electrical and Refrigerant Data ..................................................................................... 6
C. Dimensions/Connections .............................................................................................. 7
1. C-101BAH ................................................................................................................. 7
2. C-101BAH-DS ........................................................................................................... 8
3. C-101BAH-AD ........................................................................................................... 9
4. C-101BAH-ADDS .................................................................................................... 10
II. Installation Instructions .....................................................................................................11
A. Checks Before Installation ............................................................................................11
B. Location ........................................................................................................................11
1. General ....................................................................................................................11
2. Built-In Installation Site ........................................................................................... 12
C. Door ............................................................................................................................ 13
1. C-101BAH, C-101BAH-AD ...................................................................................... 13
a) Door Reversal .................................................................................................... 13
2. C-101BAH-DS, C-101BAH-ADDS ........................................................................... 15
a) Overlay Panel Fabrication and Attachment ........................................................ 15
D. Setup ........................................................................................................................... 23
E. Electrical Connection .................................................................................................. 23
F. Water Supply and Drain Connections .......................................................................... 24
G. Final Checklist ............................................................................................................ 26
III. Operating Instructions ..................................................................................................... 27
A. Important Notes About Usage ..................................................................................... 27
B. Startup ........................................................................................................................ 29
IV. Maintenance ................................................................................................................... 30
A. Maintenance Schedule ................................................................................................ 31
B. Cleaning and Sanitizing Instructions ........................................................................... 32
C. Storage Bin Drain ........................................................................................................ 34
D. Condenser ................................................................................................................... 35
E. Optional Drain Pump HS-5061 .................................................................................... 36
V. Preparing the Appliance for Periods of Non-Use ............................................................. 37
VI. Disposal .......................................................................................................................... 39
3
Important Safety Information
Throughout this manual, notices appear to bring your attention to situations which could
result in death, serious injury, damage to the appliance, or damage to property.
WARNING Indicates a hazardous situation which could result in death or
serious injury.
NOTICE Indicates a situation which could result in damage to the
appliance or property.
IMPORTANT Indicates important information about the installation, use, and
care of the appliance.
WARNING
The appliance should be destined only to the use for which it has been expressly
conceived. Any other use should be considered improper and therefore dangerous. The
manufacturer cannot be held responsible for injury or damage resulting from improper,
incorrect, and unreasonable use. Failure to install, operate, and maintain the appliance
in accordance with this manual will adversely affect safety, performance, component
life, and warranty coverage and may result in costly water damage.
To reduce the risk of death, electric shock, serious injury, or re, follow basic
precautions including the following:
• Only qualied service technicians should install and service the appliance.
• The appliance must be installed in accordance with applicable national, state, and local
codes and regulations.
• The appliance requires an independent power supply of proper capacity. See the
nameplate for electrical specications. Failure to use an independent power supply of
proper capacity can result in a tripped breaker, blown fuse, damage to existing wiring,
or component failure. This could lead to heat generation or re.
• THE APPLIANCE MUST BE GROUNDED: The appliance is equipped with a
NEMA5-15 three-prong grounding plug to reduce the risk of potential shock
hazards. It must be plugged into a properly grounded, independent 3-prong wall
outlet. If the outlet is a 2-prong outlet, it is your personal responsibility to have a
qualied electrician replace it with a properly grounded, independent 3-prong wall
outlet. Do not remove the ground prong from the power cord and do not use an
adapter plug. Failure to properly ground the appliance could result in death or serious
injury.
• Do not use an extension cord.
• To reduce the risk of electric shock, do not touch the control switch or plug with damp
hands. Make sure the control switch is in the "OFF" position before plugging in or
unplugging the appliance.
• Do not use an appliance with a damaged power cord. The power cord should not be
altered, jerked, bundled, weighed down, pinched, or tangled. Such actions could result
in electric shock or re. To unplug the appliance, be sure to pull the plug, not the cord,
and do not jerk the cord.
• Do not make any alterations to the appliance. Alterations could result in electric shock,
injury, re, or damage to the appliance.
• Do not place ngers or any other objects into the ice discharge opening.
4
WARNING, continued
• The appliance is not intended for use by persons (including children) with reduced
physical, sensory, or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Young children should be properly supervised around the appliance.
• Do not climb, stand, or hang on the appliance or appliance door or allow children or
animals to do so. Serious injury could occur or the appliance could be damaged.
• Be careful not to pinch ngers when opening and closing the door. Be careful when
opening and closing the door when children are in the area.
• Do not use combustible spray or place volatile or ammable substances near the
appliance. They might catch re.
• Keep the area around the appliance clean. Dirt, dust, or insects in the appliance could
cause harm to individuals or damage to the appliance.
NOTICE
• Protect the oor when moving the appliance to prevent damage to the oor.
• Follow the water supply, drain connection, and maintenance instructions carefully to
reduce the risk of costly water damage.
• In areas where water damage is a concern, install in a contained area with a oor drain.
• Install the appliance in a location that stays above freezing. Normal operating ambient
temperature must be within 45°F to 100°F (7°C to 38°C).
• If using the optional drain pump (HS-5061), test its operation every time the appliance
is cleaned and sanitized. See "IV.E. Optional Drain Pump HS-5061" for details. If
the optional drain pump is not operating properly, water could back up and overow,
leading to costly water damage.
• To help ensure the storage bin drain remains clear, follow the instructions in "IV.C.
Storage Bin Drain" once every 3 months or as often as necessary for conditions. If
the storage bin drain becomes clogged, water could build up in the bin and overow,
leading to costly water damage.
• If water collects in the bin and will not drain, turn off the appliance and close the water
supply line shut-off valve. Call for service.
• If water seeps from the base of the appliance, turn off the appliance and close the
water supply line shut-off valve. Call for service. Failure to do so could lead to costly
water damage.
• Do not leave the appliance on during extended periods of non-use, extended
absences, or in sub-freezing temperatures. To properly prepare the appliance for
these occasions, follow the instructions in "V. Preparing the Appliance for Periods of
Non-Use."
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear
of obstruction.
• Do not place objects on top of the appliance.
• The storage bin is for ice use only. Do not store anything else in the storage bin.
5
I. Specications
A. Construction
Top Panel
Ice Discharge
Opening
Scoop Holder
Slope
Front Panel
Bin Control
Thermostat
Bulb
Magnet
Catch
Control Switch
Door
Power Cord
Louver
B. Electrical and Refrigerant Data
The nameplate provides electrical and refrigerant data. The nameplate is located inside the
storage bin. For certication marks, see the nameplate.
We reserve the right to make changes in specications and design without prior notice.
Model Number C-101BAH
C-101BAH-DS
C-101BAH-AD
C-101BAH-ADDS
AC Supply Voltage 115-120/60/1
Amperes 4.0 AMPS
Design Pressure HI-240PSI LO-120PSI
Refrigerant 134a 3.17 OZ.
6
C. Dimensions/Connections
1. C-101BAH
Units: mm [in.]
7
2. C-101BAH-DS
Units: mm [in.]9Units: mm [in.]
8
3. C-101BAH-AD
4. C-101BAH-ADDS
Units: mm [in.]
10
II. Installation Instructions
WARNING
• The appliance must be installed in accordance with applicable national, state, and
local codes and regulations.
• CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews
are securely in place after installation. Make sure that none have fallen into the
storage bin.
A. Checks Before Installation
• Visually inspect the exterior of the shipping container and immediately report any
damage to the carrier. Upon opening the container, any concealed damage should also
be immediately reported to the carrier.
• Remove the shipping carton, tape, and packing material. If any are left in the appliance,
it will not work properly.
• Remove the package containing the accessories.
• Remove the protective plastic lm from the panels. If the appliance is exposed to the
sun or to heat, remove the lm after the appliance cools.
• See the nameplate inside the storage bin, and check that your voltage supplied
corresponds with the voltage specied on the nameplate.
B. Location
1. General
The appliance is approved for indoor or outdoor use.
NOTICE
• Normal operating ambient temperature must be within 45°F to 100°F (7°C to
38°C); Normal operating water temperature must be within 45°F to 90°F (7°C to
32°C). Operation of the appliance, for extended periods, outside of these normal
temperature ranges may affect appliance performance.
• The appliance will not work at sub-freezing temperatures. To prevent damage
to the water supply line, drain the appliance if the air temperature is going to go
below 32°F (0°C). See "V. Preparing the Appliance for Periods of Non-Use."
• The appliance should not be located next to ovens, grills, or other high heat producing
equipment.
• The location must provide a rm and level foundation for the appliance.
• The appliance requires no side or top clearance. But allow enough space at rear for
water supply and drain connections and at least 15" (38 cm) clearance at front.
• The appliance must be at oor level on a nished oor even if under a cabinet. In areas
where water damage is a concern, install in a contained area with a oor drain.
11
2. Built-In Installation Site
NOTICE
• Do not let the weight of the counter rest on the appliance.
• Do not install the appliance in a corner where the door will interfere with other
equipment or where the appliance cannot be pulled out for service.
Installation Space
Model Height Width Depth
C-101BAH
C-101BAH-DS
C-101BAH-AD
C-101BAH-ADDS
Between Two Cabinets Between a Cabinet and
34" (864 mm) minimum
15" (381 mm) minimum 24" (610 mm) minimum
32" (814 mm) minimum
the End of a Counter
C-101BAH
C-101BAH-DS
Min. 34"
(864 mm)
C-101BAH-AD
C-101BAH-ADDS
Min. 32"
(814 mm)
Min. 15"
(381 mm)
Between a Cabinet and
a Wall or Tall Cabinet
Secure: Do not
let the weight
of the counter
rest on the
appliance
C-101BAH
C-101BAH-DS
Min. 34"
(864 mm)
C-101BAH-AD
C-101BAH-ADDS
Min. 32"
(814 mm)
In a Corner
Oven
Min. 15"
(381 mm)
Min. 23"
(584 mm)
Support: Do not
let the weight
of the counter
rest on the
appliance
Appliance
12
C. Door
1. C-101BAH, C-101BAH-AD
a) Door Reversal
If you would like to reverse the door swing, follow the steps below. Otherwise, skip to
section "II.D. Setup."
1) While maintaining a hold on the door, remove the hinge stop pin from hinge (B). Pull out
the bottom of the door slightly and gently remove the door from hinge (A). See Fig. 1.
Hinge (B)
Hinge (A)
Fig. 1
Hinge Stop Pin
2) Remove the 2 bolts securing the top panel, then lift it off. See Fig. 2.
Top Panel
Bolts
Fig. 2
3) Remove hinge (A) and the bracket from the right side of the appliance and the top brace
from the left side. Rotate hinge (A) to position the gasket notch to the inside, then fasten
hinge (A) and the bracket to the left side and the top brace to the right side. See Fig. 3.
Bracket
Hinge (A)
Screw
Gasket Notch
13
Screw
Top Brace
Fig. 3
4) Remove hinge (B) from the right side of the appliance and the 2 ller screws from the
left side. Attach the 2 ller screws to the right side and attach hinge (B) to the left side.
See Fig. 4.
5) Rotate the top panel 180° from its previous position. This brings the notch that was
previously in the right rear to the left front. See Fig. 5. Hook the rear part of the panel on
the body, then secure the front with the 2 bolts removed in step 2.
Top Panel
Screws
Hinge (B)
Filler
Screws
Fig. 4
Fig. 5
Notch
6) Remove the 2 screws attaching the door handle and also remove the other 2 screws
indicated in the illustration. Use 2 of the screws to attach the handle to the other side of
the door and attach the other 2 screws in the remaining 2 holes. See Fig. 6.
7) Attach the door to hinge (A), then continue to maintain a hold on the door. Screw the
hinge stop pin into hinge (B) until it is tight. See Fig. 7.
Door Handle
Hinge (B)
Screws
Fig. 6
Hinge Stop Pin
Fig. 7
14
2. C-101BAH-DS, C-101BAH-ADDS
a) Overlay Panel Fabrication and Attachment
IMPORTANT
The overlay panel must be crafted by a professional cabinet maker to ensure
quality results.
(1) Parts
Ensure that all parts required for the overlay panel assembly are contained in the
accessories bag.
Overlay Panel Parts
No. Description Part Number Qty.
1 Threaded Wood Insert 4A4004-01 6
2 T2 Screw 4×8 SS 7P32-0408 3
3 Pan Head Screw M4×25 SS 7C12-0425 4
4 Truss Head Screw M4×8 SS 7C32-0408 2
5 Canoe Clip 4A0629-02 2
6 Sheet Metal Bracket 4A3998-01 1
1
2 3
4
5
6
15
Loading...