Horus HSC-ZP3102US-5 Installation & Operation Manual

Installation & Operation Manual

HSC-ZP3102US-5

Wireless PIR Motion Sensor

(Temperature Sensor Built-In)

Introduction

Thanks for choosing the Horus wireless PIR motion sensor of the home security device.
This sensor is a Z-Wave TM enabled device (interoperable, two-way RF mesh networking
technology) and is fully compatible with any Z-Wave TM enabled network and it’s security
framework. Every mains powered Z-Wave TM enabled device acts as a signal repeater and
multiple devices result in more possible transmission routes which helps eliminate “RF
dead-spots”.

Z-Wave TM enabled device displaying the Z-Wave TM logo can also be used with it
regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-Wave

TM

enabled networks. This sensor monitors movement, and send Z-Wave TM signal when
movement is detected inside the building. With Temperature sensor built inside, it will
send the signal out when temperature changed. When the device is secure included into
Z-Wave network, above communication will be encrypted.

Product description and specifications

In

*** For indoor use only ***

Specification:

Package Content:

Protocol: Z-Wave™
Frequency Range:

908.42MHz (HSC-ZP3102US-5)

Operating Range: Up to 100 feet line of sight
Operating Temp.: -10°C~ 40°C (14°F~104°F)
Battery: Panasonic CR123A * 1PC

1pc
1pc
1pc
1set

HSC-ZP3102US-5 sensor
CR123A Lithium Battery
Installation & Operation Manual
Accessory bag(including 2 screws,
1 adhesive tape & 1 bracket)

According to Directive 2014/53/EU (RED Directive) the following information shall be included:

The frequency and maximum transmitted power in EU are listed as belows,
HSC-ZP3102US-5: 868.40 – 868.42 MHz: -0.15 dBm

Z-Wave Command Classes:

COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_BASIC
COMMAND_CLASS_BATTERY
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_NOTIFICATION_V4 (mapping _COMMAND_CLASS_BASIC)
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Installation

Notice: If you are installing the entire Z-Wave TM system for the first time, please refer to the
installation guide of Z-Wave TM Interface Controller before installing HSC-ZP3102US-5.

1. Release cover tab to open the cover and insert a CR123A battery into the battery
compartment and LED will start to flash slowly, which means the sensor has not been
“inclusion” yet.

2. Close the cover back to sensor.

3. For “Inclusion (Auto-Inclusion)” in (adding to) a network: To add the
HSC-ZP3102US-5 to your Z-Wave network (inclusion), place your Z-Wave primary
controller into inclusion mode and the distance between sensor and controller is
suggested to be in one meter. Quick press the Program Switch of HSC-ZP3102US-5
for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise,
HSC-ZP3102US-5 will go to sleep after 10 seconds. (P.S.: Quick press the Program
Switch to send NIF again for inclusion if the auto inclusion did not success. The
HSC-ZP3102US-5 will go to sleep after 20 seconds if the inclusion did not work).

For “Exclusion” from (removing from) a network: To remove the HSC-ZP3102US-5
from your Z-Wave network (exclusion), place your Z-Wave primary controller into
“exclusion” mode, and following its instruction to delete the HSC-ZP3102US-5 to your
controller. Quick press the Program Switch of HSC-ZP3102US-5 to be excluded. The
LED on the HSC-ZP3102US-5 should start to flash.

For “Association”: removing the cover of the HSC-ZP3102US-5 to get into “Awake”

-1-