Horton 9200 User Manual

ARCHITECTURAL SPECS

SECURITY REVOLVING DOOR ENTRANCES

Control

Flow

®

1

4242 Baldwin Boulevard
Corpus Christi, Texas
USA 78405-3399
Tel: [phone]
Fax: [phone]

www.hortondoors.com

The Automatic Choice

®

2-Way Card Access Security

Series 9200 with Visdom ELITE® Anti-Piggyback/Tailgate
Revolving Door System

Page 1 of 6,

F13.1

Jan 15

DIVISION 08 - OPENINGS
SECTION 08 42 33.33 - REVOLVING DOOR ENTRANCES

Specifier Note: Coordinate and edit articles and paragraphs below to suit project requirements. Add section
numbers and titles per CSI "MasterFormat" and specifier's practice. Consult with manufacturer regarding
performance requirements for units applicable to project, as well as, related equipment and accessories required.

PART I – GENERAL

1.01 SUMMARY

A. WORK INCLUDED: Furnish complete revolving aluminum door system, as specified, that has been

manufactured, fabricated and installed to maintain performance criteria stated by manufacturer without defects,
damage or failure.

B. RELATED WORK:

1. Concrete: Division 03, applicable sections.

2. Masonry: Division 04, applicable sections.

3. Thermal and Moisture Protection: Division 07, applicable sections.

5. Openings: Division 08, applicable sections.

6. Electrical: Division 26, applicable sections.

1.02 REFERENCES

A. AMERICAN ARCHITECTURAL MANUFACTURERS ASSOCIATION (AAMA) 101: Appendix Dissimilar

Materials.

B. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI):

1. ANSI 156.27: Power and Manual Operated Revolving Pedestrian Doors

2. ANSI Z97.1: Safety Glazing Materials Used in Buildings - Methods of Test.

C. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) B221: Aluminum-Alloy Extruded Bars, Rods,

Shapes and Tubes.

D. THE ALUMINUM ASSOCIATION (AA): Aluminum Finishes Manual

E. INTERTEK, WARNOCK HERSEY (ETL): Testing Laboratory and Certification Agency joined with ETL SEMKO

F. UNDERWRITERS LABORATORY, INC. (USA & CANADA) UL 325: Electrical Door, Drapery, Gate, Louver, and

Window Operators and Systems.

1.03 SUBMITTALS

A. SHOP DRAWINGS & PRODUCT DATA: Submit drawings and product data showing layout, profiles, product

components including anchorage, accessories, finish and glazing details (where required).

B. QUALITY ASSURANCE AND CLOSEOUT SUBMITTALS: Submit the following:

1. Manufacturer's Operation and Maintenance Data.

2. Warranty document as specified herein.

1.04 QUALITY ASSURANCE

A. INSTALLERS QUALIFICATIONS: Installer shall be factory trained and experienced to perform work of this

section.

ARCHITECTURAL SPECS

SECURITY REVOLVING DOOR ENTRANCES

Control

Flow

®

2

4242 Baldwin Boulevard
Corpus Christi, Texas
USA 78405-3399
Tel: [phone]
Fax: [phone]

www.hortondoors.com

The Automatic Choice

®

2-Way Card Access Security

Series 9200 with Visdom ELITE® Anti-Piggyback/Tailgate
Revolving Door System

Page 2 of 6,

F13.2

Jan 15

B. MANUFACTURER’S QUALIFICATIONS: Manufacturer to have minimum (5) five years successful experience in

the fabrication of revolving doors of the type required for this project. Manufacturer capable of providing field
service representation during installation, approving acceptable installer and approving application method.

1.05 WARRANTIES

A. MANUFACTURER'S WARRANTY: Units to be warranted against defect in material and workmanship for a

period of one year from the Date of Substantial Completion. Manufacturer's warranty is in addition to, and not a
limitation of, other rights owner may have under Contract Documents.

B. DISTRIBUTOR'S WARRANTY: One year warranty: Labor & transportation charges for defective parts

replacement.

1.06 PROJECT CONDITIONS

FIELD MEASUREMENTS: Verify actual dimensions/openings by field measurements before fabrication and record
on shop drawings. Coordinate with fabrication and construction schedule to avoid construction delays.

1.07 DELIVERY, STORAGE AND HANDLING

A. ORDERING AND DELIVERY: Comply with factory's ordering instructions and lead time requirements. Delivery

shall be in factory's original, unopened, undamaged containers with identification labels intact.

B. STORAGE AND PROTECTION: Provide protection from exposure to harmful weather conditions and vandalism.

PART II – PRODUCTS

2.01 MANUFACTURER

HORTON AUTOMATICS, a division of Overhead Door Corporation, shall manufacture security revolving door(s) of
type(s) and size(s) specified on plans and door schedule.

2.02 EQUIPMENT

A. MANUFACTURED DOOR UNITS: Shall be Control Flow® Series 9200 Two-Way Card Access Security

Visdom ELITE® Anti-Piggyback/Tailgate with collapsing four-wing design. Units shall include operator,
enclosure/drum with canopy, door wings/panels, center shaft, bottom pivot and security mats.

B. OPERATOR: The operating mechanism shall be an adjustable power operator mounted within the enclosure

canopy. The operator shall be supplied with 1/4 HP 500 RPM high torque motor, 90 VDC electric brake, gear
box, and control panel and shall be ETL approved & tested to UL 325 Standard. Non-listed units shall not be
acceptable.

1. The double seal, corrosion-proof, cast iron gear case shall contain case hardened (60Rc) helical gears in
synthetic, low temperature oil bath lubrication.

2. Motor drive shall be enclosed to prevent EMI noise from affecting the microprocessor control.

3. A 1 1/2" (38 mm) diameter solid steel center shaft shall serve as main linkage to connect the operator to the
revolving door wings. The at-rest position of the door wings shall be adjustable to suit the traffic and desired
function.

4. An ethernet port shall be provided for communication with external display (by others) to monitor door status,
violations and operation.

C. MASTER CONTROL: The Microprocessor Master Control Panel (MCP) shall be a multiprocessor digital control

system utilizing time-division multiplexed operations to provide precision motor-drive, constant sensor
monitoring, and automated setup. An RS-232 port shall be provided for communication with external display (by