Horton 4100LE User Manual

Specify Swing Door Operators
In The Proper Section

Problem

Low Energy/ADA compliant automatic swing door operators are sometimes incorrectly specified in
MasterFormat™ 2004 Section 08 06 71 or 08 71 00 “Door Hardware,” typically resulting in an unsatisfied
owner and improper entrance operation.

Solution

Specify automatic swing door operators in Section 08 42 29.33 “Swinging Automatic Entrances” or
Section 08 71 13 “Automatic Door Operators” for code compliance, professional installation and years of
trouble-free service. With AAADM* certified installation, your clients are assured that:

• Automatic operators are properly calibrated and meet applicable codes for mode of operation

• Operators are paired correctly with the doors and associated hardware

• Product and labor warranties are backed by qualified professionals

Use These Specifications

08 42 29.33 or 08 71 13

Automatic Door Operators

Not These Specifications

08 06 71 or 08 71 00

Door Hardware

For automatic door operators

Architect Specification Guide

*Specify Horton and demand AAADM certied installation

LH-RH

LHR-RH

LH RH

All hand combinations available

Arm &
Header above

8"

Door Panel

Door clearance
(If limited use Parallel Arm)

6"
Side
Load

6"

Operator
Access

Arm &
Header above

Door Panel

Emergency break-out
feature for center pivoted door panels

Operator Access

4 1/2"

Bottom

Load

6"

Push
Plate

60" (1524)

32" (813)

Minimum

120 V AC

Required

24" (610)

Minimum

(Alternate Switch Location)

Series
4100 LE

Architect Specification Guide

Activating device to be located on each side of opening for two-way
traffic as per ANSI Safety Standard A117.1

Installation and Operation

Architectural Details

Horton Automatics
World Headquarters

4242 Baldwin Boulevard
Corpus Christi, Texas 78405-3399 USA

Phone: [phone]
Fax: [phone]

www.hortondoors.com

Horton Automatics, Ltd.
United Kingdom

Unit A, Hortonwood 31
Telford, Shropshire, England TF1-7YZ

Phone: [phone]
Fax: [phone]

A Division of

Overhead Door Corporation

A Sanwa Holdings Company

Form No. B700 ©2010 Horton Automatics Printed in U.S.A.

HD-Swing®4100LE & EasyAccess 7100
Low Energy Operators

Once the activating switch is pressed, the Series 4100LE or 7100 operator slowly opens the door and holds it open
for an adjustable length of time. This creates a barrier-free doorway and gives the pedestrian time to pass through
the door before it slowly closes using spring force of less than 15 pounds (67 N).

Adjustments:

Selection Guide

Electrical
Requirements:

120 or 220 VAC, 50 - 60 Hz,
single phase, 15 amp service.
Current draw - 3.15 amps.

• Opening speed: 3 to 6 sec. to
80° (Open check)

• Closing speed: 3 to 6 sec.
from 90° to 10° (Close Check)

• Time delay: 2 to 30 sec.
(ANSI A156.19 requires 5 sec.
minimum time delay)

Standard Single Units

Door Width Header Width

3'-0" (914) 3'-3" (991)

3'-6" (1067) 3'-9" (1143)

4'-0" (1219) 4'-3" (1295)

Standard Pair Units

Pair Width Header Width

6'-0" (1829) 6'-9" (1905)

7'-0" (2133) 7'-3" (2210)

8'-0" (2438) 8'-3" (2515)

Maximum Door Width:

4100LE 4'-6" (1524)
7100 3'-6" (1067)

Maximum Door Weight:

4100LE 700 lbs (320kg)
7100 200 lbs (91kg)

Did You Know?

Low energy
operators move the door
slowly at a rate considered
intrinsically safe

Surface Mount Bottom Access
with Out Swing Arm Assembly

Surface Mount Side Access

with In Swing Arm Assembly

Surface Mount Bottom Access

with In Swing Parallel Arm Assembly

Shown: EasyAccess

®

Series 7100 Operator

Shown: HD-Swing

®

Series 4100 Operator

Shown: HD-Swing

®

Series 4100LE

4"

Side
Load

Arm & Header above

Exterior

Operator
Access

6"

Door Panel