Horton 4000LE User Manual

Low Energy Swing Door Operators

HD-Swing® LE

Series 4000LE Heavy Duty Low Energy

Handicap Accessible

For High Trafc or Extra Large Barrier-Free Doors

Compliant with ANSI A156.19, A117.1 and Americans With Disabilities Act of 1990

Standard system features & benets:

• Heavy duty gear drive and 1/8 HP motor designed for high wind conditions, stack pressure and
high volume pedestrian trafc. Appropriate for heavy or oversized doors.

• Choice of mounting type: Surface mount or overhead concealed

• Choice of header: 6" x 6" side access or 4 1/2" x 6" bottom access

• Available for butt hung, center pivoted or off set pivot door assemblies

• Installs easily with no structural changes required

Push Plate or Push Button
Activation

Additional Features/Benets

• Push-N-Go
activation by pushing or pulling
door panel

• SoftTouch
obstruction sensing

• Easily adjustable opening &
closing speeds

• Manual operation in case of
power failure

• Available in a variety of
anodized, paint or clad nishes

®

automatic

®

reversing and

Did You Know?

Low energy

Specify Horton and demand AAADM certied installation

operators move the door
slowly at a rate considered
intrinsically safe.

Low Energy Swing Door Operators

HD-Swing® LE

Series 4000LE Heavy Duty Low Energy

Once the activating switch is pressed, the Series 4000 LE operator slowly opens the door and holds it open
for an adjustable, delayed length of time. This creates a barrier-free doorway and gives the pedestrian time to
pass through the door before it slowly closes using spring force of less than 15 pounds (67 N.)

Installation and Operation

Electrical

Activating device to be located on each side of opening for two-way
trafc as per ANSI Safety Standard A117.1

Requirements:

32" (812)

Minimum

120, 220 VAC, 50 - 60 Hz,
single phase, 15 amp service.
Current draw - 3.15 amps.

Adjustments:

• Opening speed: 3 to 6 sec. to
80° (Open check)

• Closing speed: 3 to 6 sec.
from 90° to 10° (Close Check)

• Time delay: 2 to 30 sec.
(ANSI A156.19 requires 5 sec.
minimum time delay).

Selection Guide Architectural Details

Standard Single Units

Door Width Header Width

3'-0" (914) 3'-3" (991)

3'-6" (1067) 3'-9" (1143)

Standard Pair Units

Pair Width Header Width

5'-0" (1524) 5'-3" (1600)

6'-0" (1829) 6'-9" (1905)

7'-0" (2133) 7'-3" (2210)

Maximum Door Width:

4'-6" (1524)

4 1/2" (114)

4000LE

Operator

Operator Access

Surf ace Mount Bot tom Acce ss

with Outswing Arm Assembly

Arm & Header above

Door Panel

Ext erior

24" (610)

Minimum

( Alternate Switch Location )

6" (152)

Ceil ing Line

8"

(203)

60" (1524)

6" (152)

4000LE

Operator

Surfa ce Mount Side Access

with Inswing Arm Assembly

Interior

Arm & Header
above

Appr oximat e door clearance.

Door Panel

Push
Butt on

Operator
Access

120 VAC

Required

Series
4100 LE

Push

OR

Pl ate

6" (152)

Hinge
Assem bly
by Others

Overhead Concealed Side Access

with Of fset Ar m Assembly

6" (152)

4000LE

Operator

Operator
Access

Power Arm

Drive Block

6" (152)

Horton Automatics
World Headquarters

4242 Baldwin Boulevard
Corpus Christi, Texas 78405-3399 USA

Phone: [phone]
Fax: [phone]

www.hortondoors.com

Horton Automatics, Ltd.
United Kingdom

Unit A, Hortonwood 31
Telford, Shropshire, England TF1-7YZ

Phone: [phone]
Fax: [phone]

Form No. B501, Rev. 2/2015 ©2015 Horton Automatics Printed in U.S.A.

A Division of

Overhead Door Corporation

A Sanwa Shutter Company