Horner APG XLt, HEXT240C013 User Manual
MAN0872-06-EN Specifications / Installation
(
1 Specifications
Digital DC Inputs XLT103 XLT104
Inputs per Module
Commons per
Module
Input Voltage
Range
Absolute Max.
Voltage
Input Impedance
Input Current
Upper Threshold 0.8 mA -1.6 mA
Lower Threshold 0.3 mA -2.1 mA
Max Upper
Threshold
Min Lower
Threshold
OFF to ON
Response
ON to OFF
Response
HSC Max.
Switching Rate
Analog Inputs,
Medium
Resolution
Number of
Channels
Input Ranges
Safe input voltage
range
Input Impedance
(Clamped @ -0.5
VDC to 12 VDC)
Nominal Resolution
%AI full scale
Max. Over-Current
Conversion Speed
Max. Error at 25°C
(excluding zero)
Additional error for
temperatures other
than 25°C
Filtering
HE-XT103 / HEXT240C113 / HEXT240C013
12 including 4
configurable
HSC inputs
Positive
Logic
10 kHz Totalizer/Pulse,Edges
5 kHz Frequency/Pulse,Width
XLT103 XLT104
All channels converted once
4-20 mA 1.00%
0-20 mA 1.00%
0-10 VDC 0.50%
160 Hz hash (noise) filter
1-128 scan digital running
Clock Accuracy
XLT OCS Model:
12 Digital DC Inputs / 12 Digital Outputs
2 Analog Inputs (Medium Resolution)
Specifications
24 including
4
configurable
HSC inputs
1
12 VDC / 24 VDC
35 VDC Max.
10 kΩ
Negative Logic
8 VDC
3 VDC
1 ms
1 ms
2.5 kHz Quadrature
2 2
0 - 10 VDC
0 – 20 mA
4 – 20 mA
-0.5 V to +12V
Current Mode:
100 Ω
Voltage Mode:
500 k Ω
10 Bits
32,000 counts
35 mA
per ladder scan
TBD
average filter
Digital DC
Outputs
Outputs per
Module
Commons per
Module
Output Type
Absolute Max.
Voltage
Output
Protection
Max. Output
Current per
point
Max. Total
Current
Max. Output
Supply Voltage
Minimum Output
Supply Voltage
Max. Voltage
Drop at Rated
Current
Max. Inrush
Current
Min. Load
OFF to ON
Response
ON to OFF
Response
Output
Characteristics
General Specifications
Required Power
(Steady State)
Required Power
(Inrush)
Primary Power
Range
Relative Humidity
Operating
Temperature
Terminal Type
CE
See Compliance Table at
http://www.heapg.com/Pages/TechSupport/Prod
UL
uctCert.html
Weight 12.5 oz. (354.36 g)
XLT103 XLT104
12 including
2
configurable
PWM
outputs
Sourcing / 10 K Pull-Down
4 A Continuous
650 mA per channel
Current Sourcing (Pos logic)
30 A for 1 ms @ 24 VDC
Minutes/Month at 20C
16 including
2
configurable
PWM
outputs
1
28 VDC Max.
Short Circuit
0.5 A
30 VDC
10 VDC
0.25 VDC
None
1 ms
1 ms
130 mA @ 24 VDC
10 – 30 VDC
5 to 95% Non-
condensing
-10°C to +60°C
Screw Type,5 mm
Removable
+/- Seven
Note: Highest usable frequency for PWM output is 65 KHz
__________________________________________________________________________________________________________________________________________________________________
12/18/2008 Page 1 of 4 ECN # 947
XLT OCS Model:
HE-XT104 / HEXT240C114 / HEXT240C014
24 Digital DC Inputs / 16 Digital Outputs
2 Analog Inputs (Medium Resolution)
2 Panel Cut-Out and Dimensions
Note: Max. panel thickness: 5 mm.
Refer to the XLe/XLt
User Manual for panel
box information and a
handy checklist of
requirements.
The tolerance to meet
NEMA standards is
3 Ports / Connectors / Cables
Note: The case of the XLt is black, but for clarity, it is shown in a
lighter gray color.
MJ2
(RS-232 / RS-485)
MJ1
(RS-232 / RS-485)
To Remove Back Cover:
Unscrew 4 screws located on
the back of the unit and remove
I/O Jumpers (Not Shown): I/O Jumpers (JP) are located
internally. To access, remove back cover of unit.
Wiring Connectors (J1 – J4), I/O Jumpers (JP1-3), and
External Jumpers (RS-485) are described in the Wiring and
Jumpers section of this document.
001ACC009
Connect to Earth Ground.
Torque rating 4.5 - 7 Lb-In
Note:
± 0.005” (0.1 mm).
DIP
Switch
J1
I/O
Jumper
back cover.
Power Connector
Power Up:
Apply 10 – 30 VDC.
Screen lights up.
0.50 –0.78 N-m)
3.622 [92mm]
3.622 [92mm]
Note – Your keypad overlay
appearance may differ.
Standard US/EU overlays
pictured here for example.
Memory Slot
CAUTION: Do notover tighten
screws when replacing the back
CAN Connector
Use the CAN Connector
when using CsCAN network.
Torque rating 4.5 – 7 Lb-In
(0.50 – 0.78 N-m)
001XLE002
Power
cover.
Jumper
NET 1
(CsCAN)
001XLE029-R2
J2
I/O
MAN0872-06-EN Specifications / Installation
A
A
f
t
4
Section 3 continued
Memory Slot:
Uses Removable Memory for data logging, screen
captures, program loading and recipes.
Horner Part No.: HE-MC1
Serial Communications:
MJ1: (RS-232 / RS-485) Use for Cscape programming and
pplication-Defined Communications.
MJ2: (RS-232 / RS-485) Use for Application-Defined
Communications.
8
1
Pin MJ1 Pins MJ2 Pins
TXD OUT TXD OUT
8
RXD IN RXD IN
7
0 V Ground 0 V Ground
6
+5
TX-
OUT
IN /
OUT
IN /
OUT
5*
60mA
RTS OUT TX- OUT
4
CTS IN TX+ OUT
3
RX- /
2
RX+ /
1
TX+
+5
60mA
RX- IN
RX+ IN
* +5Vdc 60mA Max
OUT
4 Wiring and Jumpers
• Wire according to the type of inputs / outputs used and select
the appropriate jumper option. Use Copper Conductors
in Field Wiring Only, 60/75° C
Wiring Specifications
For I/O wiring (discrete), use the
following wire type or equivalent:
Belden 9918, 18 AWG (0.8 mm
For shielded Analog I/O wiring,
use the following wire type or
equivalent: Belden 8441, 18
AWG (0.8 mm
For CAN wiring, use the
following wire type or equivalent:
Belden 3084, 24 AWG (0.2 mm
The XLt can be wired for Positive Logic inputs or
or larger.
2
) or larger.
or larger.
Positive Logic vs. Negative Logic Wiring
Negative Logic inputs.
12-24VDC
Positive Logic In Negative Logic In
Location of I/O jumpers (JP)
and wiring connectors
(J1 – J4).
2
)
JP1
J1 J2
2
)
I1
0V
J4
JP3
J3
I1
0V
001XLE036
4.1 I/O Jumpers Settings (JP1 – JP3)
Note: The Cscape Module Setup configuration must match
the selected I/O (JP) jumper settings.
JP1 Digital DC Inputs
Positive Logic
Negative Logic
Default
CURRENT OR VOLTAGE INPUTS
A1
A2
JP3
20mA 10VDC
1122
A1
3344
A2
001XLE043-R1
Note:
When using JP3 (A1 -A2),
each channel can be
independently configured.
___________________________________________________________________________________________________________________
4.2 External DIP Switch Settings (or Jumpers Settings)
The External DIP Switches are used for termination o
the RS-485 ports. The XLt is shipped un-terminated.
To terminate, select one of the jumpers shipped with
the product and insert it based upon the option that is
desired or, select the switch (as shown in the
illustration) and configure based upon the option tha
is desired.
4.3 Wiring Examples
Note: The wiring examples show
Positive Logic input wiring.
J1
Orange
XT103 / XT104
Name
I1 IN1
I2 IN2
I3 IN3
I4 IN4
I5 IN5
I6 IN6
I7 IN7
I8 IN8
H1 HSC1 / IN9
H2 HSC2 / IN10
H3 HSC3 / IN11
H4 HSC4 / IN12
A1 Analog IN1
A2 Analog IN2
0V Ground
J2
Black
XT103
XT104
XT103 / 104 J2 Black
0V Ground
V+ V+ *
NC
No
Connect
OUT13
10 - 30VDC
Q12 OUT12
Q11 OUT11
Q10 OUT10
Q9 OUT9
Q8 OUT8
Q7 OUT7
001XLE005-R1
Q6 OUT6
Q5 OUT5
Q4 OUT4
Q3 OUT3
Q2 OUT2 / PWM2
Q1 OUT1 / PWM1
V+* Supply for Sourcing Outputs
J3
Orange
XT104
I13 IN13
XT104 J3 Orange
Positive Logic
Digital In
I14 IN14
I15 IN15
I16 IN16
I17 IN17
I18 IN18
I19 IN19
I20 IN20
12-24VDC
I21 IN21
I22 IN22
I23 IN23
I24 IN24
0V Ground
DIPSW3: FACTORY USE
ONLY (tiny bootloader firmware
downloading). NOT TO BE
USED FOR NORMAL OCS
OPERATION.
DIPSW2: MJ2 Termination
(default – none)
DIPSW1: MJ1 Termination
(default – none)
12-24VDC
LOOP
PWR
Positive Logic
Digital Out
0V
V+
LOAD
Q13
LOAD
Q12
LOAD
Q11
LOAD
Q10
LOAD
Q9
LOAD
Q8
LOAD
Q7
LOAD
Q6
LOAD
Q5
LOAD
Q4
LOAD
Q3
LOAD
Q2
LOAD
Q1
001XLE02
I13
I14
I15
I16
I17
I18
I19
I20
I21
I22
I23
I24
0V
001XLE047
s seen when looking at the top of the XLt unit:
XT103 / 104 J1 Orange
Positive Logic
Digital In
I1
I2
I3
I4
I5
I6
I7
I8
H1
H2
H3
Note:
Loop Power requirements
20mA
0-10VDC
H4
A1
A2
0V
001XLE046
are determined by the
transmitter specification.
XT104 J4 Orange
Positive Logic
Digital Out
J4
Orange
XT104
10 - 30VDC
Q16 OUT16
Q15 OUT15
Q14 OUT14
LOAD
LOAD
LOAD
_______________________________________________
001XLE037-R1
J2
0V
V+
J4
Q16
Q15
Q14
12/18/2008 Page 2 of 4 ECN # 947
Loading...