Horner APG HE-DIQ712 User Manual

MAN0316-08 10 NOV 2006 PAGE 1 DIQ712

Mixed I/O Module

HE800DIQ712 / HE-DIQ712*

12/24 Vdc In, Positive/Negative Logic

This datasheet also covers products starting with IC300.

3A Relay Out

* HE- Denotes plastic case.

1 SPECIFICATIONS

INPUT DIQ712

Inputs per Module 14 Minimum ON Current 1 mA Commons per Module Input Voltage Range 12/24 VDC OFF to ON Response 1 ms. Peak Voltage 35 VDC Max. ON to OFF Response 1 ms. ON Voltage level Min. 9 VDC OFF Voltage level Max. 3 VDC

Input Impedance

3

> 10 KΩ

OUTPUT DIQ712

Outputs per Module 10 relay Maximum Inrush Current 3 A Commons per Module Output Type Relay OFF to ON Response 6 ms. Typical Coil Voltage 18–30 VDC ON to OFF Response .3 ms. Typical Contact Voltage

250 VAC / 30 VDC Max.

ON Voltage drop 0.2 V Max.

Maximum Load current (resistive) per output

See Derating Chart

2

3 A

Maximum OFF Current

Isolation (Channel to Ground)

Minimum Load None

Isolation (Common to

Common and Common to Bus)

Maximum Leakage

Current

500 VDC

DIQ712

200 µA

DIQ712

2500 VDC

5 µA

General Specifications

Required Power (Steady State) Required Power (Inrush) Negligible Terminal Type Spring Clamp, Removable Relative Humidity 5–95% Non-condensing Weight 9.5 oz. (256 g) CE UL

0.19 W(8 mA @ 24 VDC)

See Compliance Table at http://www.heapg.com/Support/compliance.htm

Operating Temperature

0°–60° Celsius

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.

PAGE 2 10 NOV 2006 MAN0316-08 DIQ712

2 WIRING

2.1 Input / Output Connector Wiring

12-24VDC

5-250VAC

OR

5-30VDC

5-250VAC

OR

5-30VDC

18-30VDC

LOAD

N

L

N

L

LOAD

I1

I2

I3

I4

C1

Q1

Q2

Q3

Q4

Q5

C2

Q6

Q7

Q8

Q9

Q10

C3

VC

V+

001DIQ009-R2

*

OCS Bottom View – Shows

Corresponding I/O Pin

Signal Pin

DIQ712

I1 Input 1 I2 Input 2 I3 Input 3 I4 Input 4 C1 Common for

Inputs1,2,3,4 Q1 Output 1 Q2 Output 2 Q3 Output 3 Q4 Output 4 Q5 Output 5 C2 Common for Outputs

1,2,3,4,5 Q6 Output 6 Q7 Output 7 Q8 Output 8 Q9 Output 9 Q10 Output 10 C3 Common for Outputs

6,7,8,9,10

VC Relay Coil power

common, connected

to bus common

internally.

V+ Relay Coil Power,

+18 to +30VDC,

90mA max.

Warning: To protect the module and associated wiring from load faults, use external fuse

(10

A) as shown. This warning affects DIQ712, Revisions C or higher.

Warning: Connecting high voltage to any I/O pin may cause high voltage to appear at other I/O

pins.

Warning: Wiring the line side of the AC source to loads connected to outputs 1 through 10 and

the neutral side of the AC source to the output common(s) would create a Negative Logic condition, which may be considered an unsafe practice.

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.

MAN0316-08 10 NOV 2006 PAGE 3 DIQ712

2.2 Input Connector Wiring

12-24VDC

I5

I6

I7

I8

C4

I9

I10

I11

I12

I13

I14

C5

001DIQ010

*

OCS Top View – Shows

Corresponding I/O Pin

I5 Input 5 I6 Input 6 I7 Input 7 I8 Input 8 C4 Common for Inputs

I9 Input 9 I10 Input 10 I11 Input 11 I12 Input 12 I13 Input 13 I14 Input 14

C5

Signal

DIQ712

5,6,7,8

Common for

Inputs

9,10,11,12,13,14

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.

PAGE 4 10 NOV 2006 MAN0316-08 DIQ712

3 INTERNAL CIRCUIT SCHEMATIC

I/O Connector

SmartStack

VCC

Field Side

I1

C

To Controller

I/O Connector

C2

Q3

Field Side

Q2

SmartStack

+18-30V

-

+

-

+

Q1

-

+

Specification for transient voltage suppressors (transorbs) used on output circuitry is 400 VDC bidirectional 400 W.

Note: Electro-mechanical relays comply with IEC1131-2.

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.

MAN0316-08 10 NOV 2006 PAGE 5 DIQ712

4 CONFIGURATION

Note: The status of the I/O can be monitored in Cscape Software.

Preliminary configuration procedures that apply to SmartStack™ Modules are contained in the hardware manual of the controller you are using. Refer to the Additional References section in this data sheet for a listing of hardware manuals.

Selecting the I/O Map tab provides information about the I/O registers, which are assigned to a specific

SmartStack™ Module and where the module is located in the point map. The I/O Map is determined by the model number and location within the SmartStack™. The I/O Map is not

The Module Setup is used in applications where it is necessary to change the default states of the

outputs when the controller (e.g., OCS100) enters idle/stop mode. The default turns the outputs OFF when the controller enters idle/stop mode. By selecting the Module Setup tab, each output can be set to either turn ON, turn OFF or to hold the last state. Generally, most applications use the default settings.

Warning: The default turns the outputs OFF when the controller enters idle/stop mode. To

avoid injury of personnel or damages to equipment, exercise extreme caution when changing

the default setting using the Module Setup tab.

edited by the user.

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.

PAGE 6 10 NOV 2006 MAN0316-08

y

DIQ712

5 INPUT / OUTPUT CHARACTERISTICS

.1(±15%) V-A

0

Digital Input Chart

160VAC

Derating Output Chart

(Each group of 5)

AMPS per Output

4 3 2

2 Relays 3 Rela

4 Relays

s

1

0

0 10 20 30 40 50 60 °C

5 Relays

32 50 68 86 104 122 140 °F

Typical Relay Life (DIQ712)

Voltage

(Resistive)

30 VDC 600 K 250 K 125 K 125 VAC 750 K 300 K 150 K 250 VAC

No Load

20

Million

1 Amp 2 Amp 3 Amp

500 K 200 K 100 K

Load Current

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.

MAN0316-08 10 NOV 2006 PAGE 7 DIQ712

6 INSTALLATION / SAFETY

Warning: Remove power from the OCS controller, CAN port, and any peripheral equipment

connected to this local system before adding or replacing this or any module.

Use the following wire type or equivalent:

• Belden 8917

• 16 AWG or larger

For detailed installation and a handy checklist

that covers panel box layout requirements and minimum clearances, refer to the hardware manual of the controller you are using. (See the Additional References section in this document.).

When found on the product, the following symbols specify:

Warning: Consult user documentation.

Warning: Electrical Shock Hazard.

WARNING: To avoid the risk of electric shock or burns, always connect the safety (or earth)

ground before making any other connections.

WARNING: To reduce the risk of fire, electrical shock, or physical injury it is strongly

recommended to fuse the voltage measurement inputs. Be sure to locate fuses as close to the source as possible.

WARNING: Replace fuse with the same type and rating to provide protection against risk of fire

and shock hazards.

WARNING: In the event of repeated failure, do not replace the fuse again as a repeated failure

indicates a defective condition that will not clear by replacing the fuse.

WARNING: Only qualified electrical personnel familiar with the construction and operation of

this equipment and the hazards involved should install, adjust, operate, or service this equipment. Read and understand this manual and other applicable manuals in their entirety before proceeding. Failure to observe this precaution could result in severe bodily injury or loss of life.

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.

PAGE 8 10 NOV 2006 MAN0316-08 DIQ712

For detailed installation and a handy checklist

that covers panel box layout requirements and minimum clearances, refer to the hardware manual of the controller you are using. (See the Additional References section in this document.):

• All applicable codes and standards need to be followed in the installation of this product.

• For I/O wiring (discrete), use the following wire type or equivalent: Belden 9918, 18 AWG or

larger.

Adhere to the following safety precautions whenever any type of connection is made to the module.

• Connect the green safety (earth) ground first before making any other connections.

• When connecting to electric circuits or pulse-initiating equipment, open their related breakers.

make connections to live power lines.

Do not

• Make connections to the module first; then connect to the circuit to be monitored.

• Route power wires in a safe manner in accordance with good practice and local codes.

• Wear proper personal protective equipment including safety glasses and insulated gloves

when making connections to power circuits.

• Ensure hands, shoes, and floor are dry before making any connection to a power line.

• Make sure the unit is turned OFF before making connection to terminals. Make sure all

circuits are de-energized before making connections.

• Before each use, inspect all cables for breaks or cracks in the insulation. Replace immediately if defective.

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.

MAN0316-08 10 NOV 2006 PAGE 9 DIQ712

7 ADDITIONAL REFERENCES

The following information serves as a general listing of Horner controller products and other references of

interest and their corresponding manual numbers. Visit our website listed in the Technical Support section to obtain user documentation and updates.

Note: This list is not intended for users to determine which products are appropriate for their

application; controller products differ in the features that they support. If assistance is required,

see the Technical Support section in this document.

Controller Manual Number

XLE Series (e.g., HE-XExxx) MAN0805 QX Series (e.g., HE-QXxxx) MAN0798 NX Series (e.g., HE-NXxxx) MAN0781 LX Series (e.g., LX-xxx; also covers RCS116) MAN0755 Color Touch OCS (e.g., OCSxxx) MAN0465 OCS (Operator Control Station) (e.g., OCS1xx / 2xx; Graphic

OCS250) Remote Control Station (e.g., RCS2x0) MiniOCS (e.g., HE500OCSxxx, HE500RCSxxx) MAN0305

Other Useful References

CAN Networks MAN0799 Cscape Programming and Reference MAN0313 Wiring Accessories and Spare Parts Manual MAN0347 DeviceNet™ Implementation SUP0326 Wiring Accessories and Spare Parts Manual MAN0347

MAN0227

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.

PAGE 10 10 NOV 2006 MAN0316-08 DIQ712

8 TECHNICAL SUPPORT

For assistance and manual up-dates, contact Technical Support at the following locations:

North America:+

(317) 916-4274

www.heapg.com

Europe:

(+) 353-21-4321-266

www.horner-apg.com

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.