Horner APG HE359THM200 User Manual

Download

Page 1

MAN0841-03-EN Specifications / Installation

1 Specifications

THM100 THM200 THM100 THM200

Number of

Channels

Input

Ranges

Resolution 0.1C or 0.001mV

Input

Impedance

Accuracy +/-0.1% F.S.

External

Power

Supply

Voltage

Required

Power

(Steady

State)

Required

Power

(Inrush)

Isolation

CE & UL

Compliance

4 8

J, K, R, S,B,E, T,N,

+/-50mV, +/-

100mV, +/-500mV,

+/-1V

>10MOhm

10-30Vdc

30mA @ 24Vdc,

typical

Negligible

2000Vac for 60

seconds

(Input/Power &

Input/Comms)

See Compliance Table at

http://www.heapg.com/Pages/TechSupport/ProductCert.html

Thermocouple Input Module

Conversion

Time (PLC

Update Rate)

Terminal

Type

Storage

Temp.

Operating

Temp.

Relative

Humidity

Dimensions

WxHxD

Weight 150g (6 oz.)

Communicati-

ons

Factory Default

Communicati-

ons

Parameters

Supported

Modbus

Commands

2 Wiring – I/O

HE359THM100 / HE359THM200

0.1C or 0.001mV Resolution

Determined by

Communications

w/OCS

Screw Type,

Removable

-40° to 85° Celsius

-10° to 60° Celsius

5 to 95% Non-

condensing

17.5mm x 100mm x

120mm

0.69” x 3.94” x

4.72”

Modbus/RTU

(binary)

RS-485 half duplex

38400 baud, N, 8,

1, no h/s

Default Modbus ID

1,2,3,4,5,6,8,15,16

SmartMod

Note: Number of I/O terminal connections vary from model to model

Dimensions in inches are 0.69”W x 3.95”H x 4.72”D

RS-485

I/O

DC IN

__________________________________________________________________________________________________________________________________________________________________

5/8/2009 Page 1 of 2 ECN # 950

10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9

V+ GNA V+ GNA V+ GNA V+ GNA

Pin # ADC107 ADC207 Pin # ADC107 ADC207

1 INPUT 0+ INPUT 0+ 9 INPUT 4+ 2 3 INPUT 1+ INPUT 1+ 11 INPUT 5+ 4 5 INPUT 2+ INPUT 2+ 13 INPUT 6+ 6 7 INPUT 3+ INPUT 3+ 15 INPUT 7+ 8

Notes:

Both ends of the RS-485 network should be terminated with a 100ohm, 1/4W, 1% resistor. Many OCS controllers feature dip switches or jumpers which enable appropriate termination if the OCS is located on a network end.

ANALOG

COMMON

ANALOG

COMMON

ANALOG

COMMON

ANALOG

COMMON

DD+ GND INIT

Wiring RS-485

A B C D

ANALOG

COMMON

ANALOG

COMMON

ANALOG

COMMON

ANALOG

COMMON

Wiring DC IN

Only Terminals 1

through 8 are

present on the

ADC107 model

V-

V+

10-30Vdc

ANALOG

COMMON

ANALOG

COMMON

ANALOG

COMMON

ANALOG

COMMON

Page 2

MAN0841-03-EN Specifications / Installation

3 Init Default Setup

Communication parameters will be set to INIT default after performing the procedure:

1. Install jumper between INIT and GND terminals of the RS-485 port.

2. Apply power to Smartmod unit.

3. Read parameter words to see current parameters.

4. Write changes if necessary.

The INIT Default RS485 Settings Are:

Modbus ID = 1 Baud rate = 9600 Parity = None Stop Bits = 1 Data Bits = 8 No handshake

Note: There are 2 types of default settings possible:

1. Factory default as described in section 1 (Specifications)

2. Default after INIT as described in section 3 (INIT Default Setup)

4 Configuration DATA

SmartMod Configuration settings are mapped into Modbus Register space. This configuration data may be modified with any Modbus/RTU Master device. For convenience, Horner APG has developed a variety of Cscape application files which allow an OCS (Xle, NX, LX, QX) to act as a SmartMod configurator. Initial configuration of SmartMod module should be done on an individual basis, since all modules come from the factory with a default Modbus ID of 1. Once each module on the network has its own unique Modbus ID, further configuration adjustments can be made with the entire network powered.

All configuration parameters listed below (except 40012 Channel Enable) are stored in EPROM. That means they should not be constantly rewritten.

Configuration Parameters – Registers 40001 through 40013

Modbus

4000140005

40006 40007 Modbus ID 1 255 1

40008 40009 40010 Modbus Coil Data

40011 Input Type See Table 1 (+/- 50 mV) 40012 Channel Enable See Table 40013 Reserved

Bits 7-15 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Unused Mode Parity

Value Input Type Value Input T ype

1 +/-50mV 14 Type J T/C 2 +/-100mV 15 Type K T/C 3 +/-250mV 16 Type T T/C 4 +/-1000mV 17 Type E T/C

5-13 Not Used 18 Type R T/C

D-

D+

GND

INIT

Description Min Max Default

Reserved

Communications

Parameters

Rx/Tx Dela y (in 2mS

steps)

Watchdog Timer (in 0.5s

steps)

See Table

0 255 0mS 0 255 10 (5s)

Not Configuration Dat a – See

Data

Bits

Value Meaning Value Meaning

0 = ASCII Mode

1 =

RTU

Mode

0 Mark 0 1200 baud 1 Even 2 Odd 2 4800 baud 3 Space 3 9600 baud

0 = 7 Data

Bits

1 = 8 Data

Bits

5-7 38400 baud

19 Type S T/C 20 Type B T/C 21 Type N T/C

38.4kbaud,

N, 8, 1, RTU

Mode

I/O Data

255

(Channels

1-8 enabled)

Baud Rate

1 2400 baud

4 19200 baud

Bit 8-15 Bit 7 Bit 6 Bit 4 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Unused Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1 Input 0

0 = Disable Input

1 = Enable Input

5 Input/Output DATA

SmartMod Analog I/O utilizes both Modbus Registers (40001-40030) and Coils (1-11). It is possible to access all data using Registers only, because the Coils can be accessed through Register 40010.

The following tables lists all Modbus I/O data available.

I/O Register Data (Registers 40014-40022) Modbus Register

40010 40014

Description Access Minimum Maximum Units

Mirror of Coil

Data

Cold Junction

Temperature

Read/Write n/a n/a n/a

Read-only -1000 6000 0.01 degrees C

40015 Input 0 Read-only 0.1C or 0.001mV 40016 Input 1 Read-only 0.1C or 0.001mV 40017 Input 2 Read-only 0.1C or 0.001mV 40018 Input 3 Read-only 0.1C or 0.001mV 40019 Input 4 Read-only 0.1C or 0.001mV 40020 Input 5 Read-only 0.1C or 0.001mV

Depends

on Input

Type

Depends

on Input

Type

40021 Input 6 Read-only 0.1C or 0.001mV 40022 Input 7 Read-only

Modbus

Coil

Description Access

00001 Open Detect Input 0 Read/Write 00002 Open Detect Input 1 Read/Write 00003 Open Detect Input 2 Read/Write 00004 Open Detect Input 3 Read/Write 00005 Open Detect Input 4 Read/Write 00006 Open Detect Input 5 Read/Write 00007 Open Detect Input 6 Read/Write 00008 Open Detect Input 7 Read/Write 00009 Watchdog Enabled Read/Write 00010 Watchdog Event Read/Write

00011 Power-up Event Read/Write

Watchdog Event & Power-up

Event Operation

If Coil 9 (Watchdog Enabled) is set, Coil 10 (Watchdog Event) will set if the Watchdog Timeout value is exceeded. The Watchdog Timeout value is set in Register 40009. When set, Coil 10 can be reset by the controller when normal communications resumes.

The Power-up Event (Coil 11) is set every time the power is applied. It can be cleared by the controller if desired.

0.1C or 0.001mV

6 Installation / safety

Warning: Remove power from the OCS controller, CAN port, and any peripheral equipment

connected to this local system before adding or replacing this or any module.

a. All applicable codes and standards should be followed in the installation of this product. b. Shielded, twisted-pair wiring should be used for best performance. c. Shields may be terminated at the module terminal strip. d. In severe applications, shields should be tied directly to the ground block within the panel. e. Use the following wire type or equivalent: Belden 8441.

For detailed installation and a minimum clearances, refer to the hardware manual of the controller you are using.

When found on the product, the following symbols specify:

handy checklist that covers panel box layout requirements and

Warning: Electrical Shock Hazard.

Warning: Consult user documentation.

7 Technical Support

Technical Support at the following locations:

North America:

Tel: 317 916-4274 Fax: 317 639-4279 Web: http://www.heapg.com

techsppt@heapg.com

Email: No part of this publication may be reproduced without the prior agreement and written

permission of Horner APG, Inc. Information in this document is subject to change without notice.

Europe:

Tel: +353-21-4321266 Fax: +353-21-4321826 Web: http://www.horner-apg.com Email: tech.support@horner-apg.com

__________________________________________________________________________________________________________________________________________________________________

5/8/2009 Page 2 of 2 ECN # 950