HORNER KEPServerEX OPC Quick Start Manual

MAN0802-02 18 APR 2006 PAGE 1

r

Horner KEPServerEX OPC Serve

Quick Start Guide

1 INTRODUCTION

The Horner version of KEPServerEX OPC Server (HEOPC500) offers an OPC Server solution, which
supports Horner products.

The HEOPC500 incorporates the KEPServerEX OPC Server software from Kepware Technologies, Inc.
and includes the standard KEPServerEX install, including all files required for interoperability between the
software and the Horner APG OCS family of products.

The HEOPC500 supports communications with OCS family products through a variety of methods,
including direct serial connections, Ethernet connections, and via a Horner CsCAN connection. The
CsCAN connection requires a computer CsCAN interface, either the CsCAN PCI Interface
(HE200KGM561) or CsCAN USB Interface
Horner APG.

(HE200KGM571) – each of which are also available from

Note: Do not

The KEPServerEX product is a robust, feature-rich software product. For more details on its capability as
well as system requirements, refer to the Kepware website at:

http://www.kepware.com/Products/kepserverex_features.html

use global bits over Ethernet using HEOPC500; all points are accessed as direct data.

Note: Horner’s Legacy OPC Server Software for CsCAN is HE200CGM510. This is the part number for
the original Horner OPC Server, which is now obsolete and superseded by the HEOPC500.

2 Package Contents

 KEPServerEX License Number
 Installation Compact Disk (CD)

The CD contains:

 KEPServerEX.exe
 Horner_OCS_u.dll file
 Cscan.dll file
 Horner_OCS.chm
 This OPC Quick Start Guide

standard install file

No part of this publication may be reproduced without the prior agreement and written permission of Horner APG, Inc.
Information in this document is subject to change without notice.
Cscape, SmartStack, SmartStix and CsCAN are trademarks of Horner APG. KEPServerEX is trademark of Kepware Technologies, Inc.

PAGE 2 18 APR 2006 MAN0802-02

3 Installation

Note: The order in which installation steps are performed is very important – read carefully.
Step 1 – If you are using a CsCAN PCI interface card (HE200KGM561) or CsCAN USB interface card

(HE200KGM571), install it completely per its instructions.

Note: Refer to the Technical Support section in this datasheet for the Horner web address to

obtain the Quick Start Guide for CsCAN (PCI and USB) Interface products (MAN0804).

Step 2 – Install the standard KEPServerEX install package by executing the file KEPServerEX.exe.

Follow the installation instructions to completion.

Step 3 – Place the horner_OCS_u.dll file in the KEPServerEX Drivers folder. The standard location for

this folder is C:\Program Files\KEPServerEx\Drivers\.

Step 4 – Place the Cscan.dll file in the Windows System 32 folder. The standard location for this folder

on many computers is C:\WINDOWS\system32\.

Step 5 – Place the horner_OCS.chm file in the KEPServerEX Help folder. The standard location for this

folder is C:\Program Files\KEPServerEx\Help\.

Note: If you obtain this file electronically – not from the CD – the file can be named

horner_OCS.txt. This is named as such to prevent being blocked by many network

firewalls. You need to rename the file manually to horner_OCS.chm before moving it to
the correct location.

Step 6 – Reboot your computer.
Step 7 – Run the KEPServerEX software. Click on Help and select License a Driver or Plug-in…

Select the Horner Driver and enter the license number provided in the HEOPC500 package.

Note: Enter the license number using the following format: n-nnnnn-nnnnnnnnnnn-nnnn

Step 8 – Contact Kepware Technologies, Inc. to register your software. The software prompts you for

this. It is a required step. Kepware contact information is in the KEPServerEX Help menu.

No part of this publication may be reproduced without the prior agreement and written permission of Horner APG, Inc.
Information in this document is subject to change without notice.
Cscape, SmartStack, SmartStix and CsCAN are trademarks of Horner APG. KEPServerEX is trademark of Kepware Technologies, Inc
.

MAN0802-02 18 APR 2006 PAGE 3

4 SAFETY

When found on the product, the following symbols specify:

WARNING: To avoid the risk of electric shock or burns, always connect the safety (or earth)
ground before making any other connections.

WARNING: To reduce the risk of fire, electrical shock, or physical injury it is strongly
recommended to fuse the voltage measurement inputs. Be sure to locate fuses as close to the
source as possible.

WARNING: Replace fuse with the same type and rating to provide protection against risk of
fire and shock hazards.

WARNING: In the event of repeated failure, do not replace the fuse again as a repeated failure
indicates a defective condition that will not

WARNING: Only qualified electrical personnel familiar with the construction and operation of
this equipment and the hazards involved should install, adjust, operate, or service this
equipment. Read and understand this manual and other applicable manuals in their entirety
before proceeding. Failure to observe this precaution could result in severe bodily injury or
loss of life.

• All applicable codes and standards need to be followed in the installation of this product.

• For I/O wiring (discrete), use the following wire type or equivalent: Belden 9918, 18 AWG or

Adhere to the following safety precautions whenever any type of connection is made to the module.

• Connect the green safety (earth) ground first before making any other connections.

• When connecting to electric circuits or pulse-initiating equipment, open their related breakers. Do

• Make connections to the module first; then connect to the circuit to be monitored.

• Route power wires in a safe manner in accordance with good practice and local codes.

• Wear proper personal protective equipment including safety glasses and insulated gloves when

• Ensure hands, shoes, and floor are dry before making any connection to a power line.

• Make sure the unit is turned OFF before making connection to terminals. Make sure all circuits

• Before each use, inspect all cables for breaks or cracks in the insulation. Replace immediately if

Warning: Consult user documentation.

clear by replacing the fuse.

larger.

not

make connections to live power lines.

making connections to power circuits.

are de-energized before making connections.
defective.

Warning: Electrical Shock Hazard.

No part of this publication may be reproduced without the prior agreement and written permission of Horner APG, Inc.
Information in this document is subject to change without notice.
Cscape, SmartStack, SmartStix and CsCAN are trademarks of Horner APG. KEPServerEX is trademark of Kepware Technologies, Inc.

PAGE 4 18 APR 2006 MAN0802-02

5 TECHNICAL SUPPORT

For assistance and manual updates, contact Technical Support at the following locations:

North America:

[phone]
www.heapg.com
email: [e-mail]

Europe:

(+) 353-21-4321-266
www.horner-apg.com
email: [e-mail]

No part of this publication may be reproduced without the prior agreement and written permission of Horner APG, Inc.
Information in this document is subject to change without notice.
Cscape, SmartStack, SmartStix and CsCAN are trademarks of Horner APG. KEPServerEX is trademark of Kepware Technologies, Inc
.