Page 1
Owner’s Manual
RAPiD
SAFE
™
Item No. 98150
Page 2
READ THIS FIRST
Warning: NEVER store a loaded firearm in the Hornady Security™ RAPiD™
safe under any circumstances. The risks associated with storage of a loaded
firearm include, but are not limited to, unintentional discharge upon insertion
or removal of the firearm. Unintentional discharge may result in bullet and safe
fragments dispersing in multiple directions, which may cause serious injury or
™
death. Hornady Security
Warning: No safe is entirely secure. The RAPiD
your maintenance of the combination code, keys, and RFID tags. You are solely
responsible for maintaining your combination code, keys, and RFID tags. Never
write down your combination code. Keep your keys and RFID tags in a secure
location at all times. Store your RAPiD
your keys and RFID tags. Hornady Security
access, including damage to, or loss of property, or personal injury. Again,
NEVER store a loaded firearm in your Hornady RAPiD
in unauthorized access to the loaded firearm.
Warning: Except as expressly provided in the RAPiD
Hornady Security
™
your inability to open the RAPiD
the keys furnished operate the lock. Keep your keys in a secure location at all
times. For your security, Hornady Security
Warning: Hornady Security
personal property. The RAPiD
from fire, water, humidity, or other environmental conditions. Do not, under
any circumstances, return the RAPiD
personal property inside.
is not liable for any misuse of the RAPiD™ safe.
™
safe is only as secure as
™
safe in a secure location away from
™
is not liable for unauthorized
™
safe, as this may result
™
Safe Limited Warranty,
is not liable for any expense or damage associated with
™
safe. Electronic systems may fail. Verify that
™
WILL NOT send replacement keys.
™
is not liable for any loss, theft, or damage to
™
safe is not intended to protect the contents
™
safe to Hornady Security™ with any
Important Information
• RFID Tag refers to the chip in any of the RFID “keys” included with the
RAPiD™ safe (bracelets, key fob or card).
• For trouble-free operation of your RAPiD™ safe, please read and understand
all instructions before use.
• Questions? Call our tech line at 800-338-3220.
• Never store loaded firearms in the RAPiD™ safe. Follow local laws for
firearm storage.
Page 3
Table of Contents
Warnings and Important Information ....................................................... Page 2
Items Included .......................................................................................... Page 3
Setup and Operation ................................................................................. Page 4
Warranty.................................................................................................... Page 9
Product Registration and Service ............................................................ Page 10
Frequently Asked Questions ..................................................................... Page 10
Mounting Template .................................................................................... Page 11
Items included with your RAPiD™ Safe
1. RAPiD™ Safe
2. Wall Power Supply (including 220 Volt Adapter for European Usage)
3. Three (3) RFID Bracelet Tags (One of each size: M, L, XL)
4. One (1) RFID Card Tag
5. One (1) RFID Key Fob Tag
6. Two (2) Circular (Barrel) Keys
7. Security Cable
Not Pictured:
• Owner’s Manual
• Warranty Card
®
• Hornady
Decal Magnet
1
3
6
5
4
2
7
Exterior: 15½"x9"x3½"
Interior: 11"x8"x3"
Weight: 15.65 lbs
Power: 12V 1.0A
3
Page 4
RAPiD™ Safe Setup and Operation
Congratulations on purchasing the technologically advanced RAPiD™ safe. You have taken a
significant step in securing the safety of your handgun.
To achieve the best experience with your RAPiD™ safe, please read all instructions carefully,
and understand its operation.
After the RAPiD™ safe has been taken out of the box, please check to be sure the circular
(barrel) key fits and unlocks your RAPiD™ safe (See page 7 for Manual Lock information).
Contact Hornady® at 800-338-3220 if the key does not work.
Combination Code
Your safe’s factory preset combination code is 1-2-3-4-ENTER.
Opening and Closing RAPiD™ Safe
Open your safe by plugging the unit into an
electrical outlet. Enter the factory preset
code: 1-2-3-4-ENTER.
Close the safe by pressing the lid down until
its bolts are engaged.
NOTE: NEVER close the safe until the latch
motor has returned to home position.
Changing the Combination Code
To create a new 4, 5, or 6 digit code:
1. Open your RAPiD™ safe.
Latch in Home
Position
2. Locate the three small program buttons
on its inside right corner.
3. Press the top white button.
4. When the amber status light on the front
keypad blinks, the system is ready to
receive your code.
5. Key in your preferred 4 to 6 digit code,
and press ENTER.
6. The keypad will blink twice, indicating your code has been correctly saved.
7. WITH THE LID OPEN, test the code. If the motor does not run, repeat steps 2 through 7.
NOTE: Keypad is equipped with an anti-tamper feature that disables the keypad for
2 minutes upon 5 consecutive incorrect keypad code entries. This feature does not disable
normal opening function using RFID Tag.
4
Program Buttons
Page 5
RFID Tags
Your RAPiD™ safe includes five (5) different
RFID tags, including:
• 3 Bracelets (M, L, XL)
• 1 Key Fob
• 1 Card
The safe’s system can only store up to two (2)
different tags at a time. Only two tags can be
programmed for use. The remaining three tags
will be inert, but can be circulated as one of
the programmed tags if you choose to use
them later, i.e., you can program two bracelets,
or one bracelet and the card, but no more than
two tags may be programmed for use at any
given time.
How To Change Your RFID Tags
The RAPiD™ safe can store up to 2 tags.
To program these tags:
1. Open your RAPiD™ safe.
2. Locate the three small program buttons on
the inside right corner.
3. Press the middle (black) button to program
your FIRST RFID tag. Choose one of the five
tags listed above.
4. When the amber status light on the keypad
blinks, the system is ready for your RFID tag.
5. Place the RFID tag approximately 1/2" over
the RFID reader (H logo) that is located on
the front panel of the safe.
6. Wait for the status light to display green.
7. Remove the tag from the RFID reader on the
front panel of the safe.
8. WITH THE LID OPEN, test the tag by placing
it approximately 1/2" over the RFID reader. If
you do not hear and see the motor activate,
repeat steps 2 through 8.
9. The second RFID tag can be programmed
by pushing the third, lowest (black) button
inside the box and following the steps above.
Choose the two RFID entry methods (tags)
you prefer, and program them for use.
Program Buttons
5
Page 6
Battery Power Mode
When the RAPiD™ safe is unplugged, and is operating on battery power, you must press
the ENTER key to activate system.
Pressing the ENTER key causes the system to achieve ready status. This includes RFID tag
reading and keypad operation.
For example: To open your safe with an RFID tag, while the system is running on
battery power, first press the ENTER key to bring it to ready status. Place your RFID tag
approximately 1/2" over the RFID reader to open the safe.
To open your safe with your keypad code, first press the ENTER key to bring it to ready
status. Enter your code on the keypad followed by ENTER, to open the safe.
Keypad Status Light Codes
When the light
displays:
Solid Red
Blinking Amber
Solid Amber
Solid Green
It means:
The system is
powered and ready.
The system is ready to
program.
The battery is low.
Replace batteries
immediately.
The system is
unlocking.
Backlit Reader
Your safe’s backlit reader remains on
while the system is plugged into an
electrical outlet, unless you switch it off.
The backlit reader will switch off when the
system times out for 20 seconds under
battery power only.
To turn the light off (when using electrical
power), open the safe, and locate the
on/off switch next to the white program
button.
6
Backlit Reader
On/Off Switch
Page 7
Manual Lock
The mechanical key lock is located under the keypad panel. To manually unlock the RAPiD™
safe, carefully remove the keypad panel by pushing the locking tab toward the “H” and then
lifting up, carefully protecting the attached wires. Press the safe lid down while turning the
key to unlock the unit.
Manual Lock
Left-Hand/Right-Hand
Feature
To reverse the keypad panel for opposite
hand usage, press the side-locking tab
and reverse the keypad panel, carefully
protecting the attached wires.
Batteries
For backup or mobile use, your safe requires
eight AA batteries (not included). To install
or replace batteries, carefully remove the
keypad panel and battery case cover. Only
use new alkaline AA batteries. Verify the
battery pack is plugged in. Replace all
batteries at the same time.
NOTE: The RAPiD™ safe is not designed to
operate on a 9V battery.
NOTE: Solid Amber status light indicates
low battery. Batteries should be replaced
immediately.
NOTE: Replace batteries every 12 months.
Side-Locking Tab
Status Light
7
Page 8
Removing & Reinstalling
the RAPiD™ Sleeve
The RAPiD™ sleeve accommodates most
5-inch pistols, and 4-inch barreled
revolvers. Removing the RAPiD™ sleeve can
accommodate larger handguns or other
valuables.
To remove the sleeve, lift the levers located
on each side of the sleeve, and pull it out.
Reinstalling the sleeve is just as simple.
Make sure the levers are up and push the
sleeve in place, aligning the notches with
the bar. Press the levers down to lock the
sleeve in place. Remove and reinstall the
sleeve a few times to become familiar
with the process.
Security Cable
Locked Lever
RAPiD™ Sleeve
Unlocked Lever
RAPiD™ Safe
without Sleeve
The RAPiD™ safe includes a security cable, that
can be looped around a stationary object. With the
safe cover open, place the lug end of the cable
into the security cable slot and close the lid.
Cable
8
Cable
Page 9
RAPiD™ Safe Limited Warranty
Hornady Security™ warrants the RAPiD™ safe will, in normal use and service, be free from
defects in workmanship or materials for one (1) year from date of purchase.
This Limited Warranty does not cover any of the following:
(a) Damage, deterioration, or malfunction resulting from accident, negligence,
misuse, improper installation, or lack of maintenance;
(b) Any defects not discovered and reported to Hornady Security™ during the
one (1) year warranty period;
(c) Usual and customary deterioration or wear resulting from normal use.
This Limited Warranty is not transferable and is enforceable by the original owner only. In
the event that Hornady Security™ receives notice from the original purchase of a warranty
claim in conformity herewith, Hornady Security™ will promptly undertake an investigation
of such claim. If the warranty claim is covered by the Limited Warranty, Hornady Security,™
will, in its sole discretion, repair the defect(s) or replace RAPiD™ safe at the expense of
Hornady Security.
Disclaimer of Implied Warranties. EXCEPT AS IS OTHERWISE EXPRESSLY SET FORTH IN
THE ABOVE LIMITED WARRANTY, HORNADY SECURITY™ MAKES NO OTHER REPRESENTATIONS
OR WARRANTIES OF ANY KIND, WHETHER EXPRESSED OR IMPLIED, BY OPERATION OF LAW
OR OTHERWISE WITH RESPECT TO THE RAPiD™ SAFE OR ANY COMPONENT PART THEREOF,
INCLUDING WITHOUT LIMITATION ANY REPRESENTATION OR WARRANTY WITH RESPECT TO
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE OR USE.
™
Limitation on Liability. THE OBLIGATION OF HORNADY SECURITY™ TO REPAIR OR REPLACE
AS PROVIDED ABOVE SHALL BE THE SOLE AND ONLY REMEDY RESPECTING ANY DEFECT
IN THE RAPiD™ SAFE, OR ANY COMPONENT PART THEREOF. IN THE EVENT THAT THE
FOREGOING REMEDY FAILS OF ITS ESSENTIAL PURPOSE, THE LIABILITY OF HORNADY
SECURITY™ TO PURCHASER SHALL NOT, IN ANY EVENT, EXCEED THE ACTUAL PURCHASE
PRICE OF THE NON-CONFORMING GOODS; AND
Limitation on the Nature of Damages. HORNADY SECURITY™ SHALL NOT, UNDER ANY
CIRCUMSTANCES, BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL,
INDIRECT, INCIDENTAL, CONSEQUENTIAL, LIQUIDATED OR PUNITIVE DAMAGES OF ANY
NAME, NATURE OR DESCRIPTION. HORNADY SECURITY™ IS NOT RESPONSIBLE FOR DAMAGE
TO OR THEFT OF THE RAPiD SAFE, OR ITS CONTENTS.
9
Page 10
Product Registration and Service
You must register your RAPiD™ safe in order to obtain Warranty Service. Simply complete
and return the enclosed product registration card or submit through our website by going to
hornady.com/warranties
To Receive Warranty Service
In order to report a warranty claim, call Hornady Security™ at 800-338-3220 to request a
return authorization number. Returns will not be accepted without prior return authorization
by Hornady Security.™ When a return authorization number has been obtained, be sure all
contents have been removed from the RAPiD™ safe before sending it for service. Hornady
Security™ is not liable for any loss, theft, or damage to personal property.
Post-Warranty Service Information
For issues concerning service after the Limited Warranty expires, contact Hornady Security™
at 800-338-3220.
Frequently Asked Questions
I’ve lost my keys. Can I get a replacement?
For security reasons, Hornady WILL NOT provide replacement barrel keys for the RAPiD™ safe.
Consult a locksmith if needed.
Where can I find the serial number?
The serial number is located under the keypad panel.
How long does my access code need to be?
Your code must be 4-to-6 digits long.
How long should the batteries last?
Quality batteries should last approximately 12 months, depending on use.
What size handgun will the RAPiD™ safe accommodate?
The RAPiD™ sleeve accommodates most 5-inch pistols, and 4-inch barreled revolvers.
Removing the RAPiD™ sleeve allows more space for larger handguns.
How do I return my RAPiD™ safe for warranty work?
Call Hornady® at 800-338-3220 and one of our technicians will assist you.
Why isn’t my RFID tag (bracelet, key fob, card) opening the safe?
• Be sure the RFID tag is programmed to your safe. The RAPiD™ safe allows two (2)
RFID tags to be programmed for use.
• Check the power source. If the unit is plugged into an electrical outlet, the red
LED light should be on. If the unit is on battery power, press any keypad button
(to bring the system to ready) before placing the RFID tag on the reader.
10
Page 11
Mounting Template
Align corner
of template to
the front right
corner of safe.
ALIGN TEMPLATE WITH FRONT KEYPAD EDGE
Page 12
586064
P.O. Box 184 8, Grand Island, Nebraska 68802-1848
308-382-1390 • 800-338-3220 • Fax: 308-382-5761
www.hornady.com • webmaster@hornady.com
Loading...