OWNER'S MANUAL
LOCK-N-LOAD®
RIFLE BULLET FEEDER
30 CAL
CONVERSION KIT
P.O. Box 1848, Grand Island, Nebraska 688 02-1848
308-382-1390 • 800-338-3220 • Fax: 308-382-5761
www.hornady.com • Hornady.com/contact_us
78 0311 07/ 2014
30 Cal. Feed Plate Conversion Kit
Rifle Bullet Feeder Die
Item No. Part No. Qty. Description
1 399213 1 Tube Spring Clamp
2 399210 1 Button Head Cap Screw (BCHS ), 10-32 x 1/4
3 392011 1 Hex Nut, 10-32
4 399209 1 Steel Knurled Thumb Screw
5 399354 1 Bullet Drop Funnel, 30 Cal.
6 399205 1 Screw Adjustment Bullet Feed
7 399206 1 Screw Lock Nut Adjustment
8 398067 1 Rubber Washer
9 399208 1 Center Plate Adjustment Nut
10 398400 1 Thumb Screw, 1/4-20 x 1
11 399356 1 Hopper Turning Plate, 30 Cal.
12 398401 2 Flat Head Cap Screw ( FHCS), 10-32 x 3/8
13 399352 1 Bullet Feeder Wheel, 30 Cal.
3
2
1
11
1
2
3
16
4
5
6
18
7
8
4
9
10
5
11
12
6
7
8
13
9
27
14
5
26
6
25
22
24
Item
Part
No.
No. Qty. Description
1 399327 1 Feeder Clamp, RBF
2 69006 1 Thumb Screw, 6-32 x .40
3 399322 1 Seat Adjust Screw, RBF
15
4 399326 1 Seating Stem, 30 Cal , RBF
5 044800 3 Seat Adjust Lock Ring
6 398067 2 Rubber Washer
17
7 399320 1 Crimp Adjust Screw, RBF
8 398906 1 Crimp Adjust Lock Ring
19
9 480083 1 Crimp Adjust Locking O-Ring
10 399324 1 30 Cal Alignment Sleeve, RBF
11 399371 1 Bullet Retaining O-Ring, RBF
12 399321 1 Die Body, RBF
20
13 044000 1 Lock Ring
21
14 399341 1 Feed Tube Retainer, 30 Cal, RBF
15 399339 1 Feed Support Bracket, Black
23
16 392452 2 Hex Nut, 6-32
17 399340 2 Pan Head Screw, 6-32 x 5/16
18 399336 1 Shoulder Bolt, 1/4 x 5 /8 10-24
19 399335 1 Feed Block, 30 Cal Long
20 399334 1 Feed Block, 30 Cal Short
21 399337 1 Torsion Spring, 1/4"
22 399167 2 Pan Head Thread Cut, 4-40 x 3/8
23 399331 1 Feeder Cap
24 399328 1 Feeder Body
25 399338 1 Compression Spring, 1/4"
26 399330 1 Dowel Pin, 1/4 x 2
27 399329 1 Bullet Ramp
10
13
12
Switch Retainer Assembly
3
4
6
Item No. Part No. Qty. Description
1 399347 3 4- 40 x 11/16 Pan Head Screw
2 399364 1 Micro Switch (Cherry D42LR1XL )
3 399345 1 Switch Retainer, 30 Cal
4 399344 1 Feed Tube, 30 Cal
5 399350 1 Feed Spring, 3 0 Cal
6 392458 3 4-4 0 Hex Nut
1
2
5
Remove 22 Caliber Bullet Feed Die
2
4
5
6
1
Remove the 22 caliber bullet feed die from your
press. Remove any bullets from inside the die
before storing it.
NOTE: If using the Lock-N-Load® bushing system, your die
will be set for the next use.
Remove Feed Spring
2
Loosen the thumb screw to disconnect the 22
caliber feed spring from the drop funnel. Remove
the 22 caliber feed spring and switch assembly.
Remove 22 Caliber Bullet Guide Plate
4
Loosen the thumb screw and slide the 22 caliber
Bullet Guide Plate out of the hopper.
Remove 22 Caliber Feed Wheel
5
Rotate the wipers to the side and slide the 22
caliber Feed Wheel out of the hopper.
Empty 22 Caliber Bullets
3
Remove all bullets from the hopper.
NOTE: Use two small hex wrenches or two ¼-20 bolts to lift
the Feed Wheel out of the hopper.
Set Up 30 Caliber Feed Wheel
6
6
Place the 30 caliber Feed Wheel and 30 caliber
Bullet Guide Plate in the hopper.
Set Up 30 Caliber System
7
Use the same steps found in the 22 caliber Rifle
Bullet Feeder manual for further setup and
adjustment.
Keep in mind the following information:
Bullets
• Use pointed bullets (spire point, polymer tip,
hollow point, etc.) The rifle bullet feeder does
not feed round nose or flat point bullets.
• Bullet lengths from approximately .80" to 1.05"
will use the short feed block. Bullet lengths from
approximately 1.05" to 1.55" will use the tall feed
block. Do not use bullets outside this range.
*These instructions are also available online at
hornady.com/manuals.
Case Lengths
• The 30 caliber rifle bullet feeder will feed, seat,
and crimp rifle cases from 1.82" to 2.85" in
length (300 Savage to 300 Rem Ultra Mag) in a
Hornady® press.
Loading...