Page 1
®
Lock-N-Load
Hot Tub™
Sonic Cleaner
Instruction Manual
™
Page 2
PARTS & ACCESSORIES
Small Parts
Tank (1 pc)
Basket (1 pc)
A. Removable Top Cover
B. Slide Cover & Drain Tray
C.
9L Stainless Steel Tank
D. Durable ABS Housing
E. Removable Drain Tray
F. Digital Control Panel
G. Convenient Carry Handles
H. Integrated Drain
I. Drain Hose Fitting
Hose (1 pc)Power Cord (1 pc)
IMPORTANT SAFETY FUNCTIONS
WARNING - Before operating the unit, please carefully read and
understand this document.
1. Only use Hornady approved cleaners such as One Shot
Sonic Clean
™
Cartridge Case Solution or One Shot® Sonic Clean™
®
Gun Parts Solution.
2. Leave the machine unplugged until you are ready to clean
parts and have read these instructions.
3. Unit must be unplugged when filling or emptying tank.
4. Do not overfill tank.
5. Do not place hands in unit while unit is running.
6. Do not plug in or unplug unit with wet hands.
7. Do not immerse unit in water.
8. Do not operate unit if power cord is damaged, the unit
has been submerged in water, or appears damaged.
9. Do not leave plugged in while unattended.
10. Do not operate unit without solution in tank.
11. Do not operate the unit for longer than 30 minutes
without allowing the unit to cool for at least 5 minutes.
Suspension Cord (4 pcs)
12. Do not put easily discolored items into tank such as clothing,
leather, wood etc.
13. Do not put electrical devices into unit that are not waterproof.
14. Do not clean eyewear frames or artwork made from shell
or hawksbill.
15. Use extreme caution when cleaning aluminum parts in the unit.
This unit may damage low grade and/or thin aluminum.
16. Do not leave cleaning solution in tank for an extended period
of time.
17. Keep unit away from direct heat sources.
18. Store unit in a dry, flat place.
19. Do NOT use heat function on sensitive items or painted parts.
NOTE: The Lock-N-Load® Sonic Cleaner™ may appear to be off or can not be
turned off when it is subjected to electrical power surges. If this happens,
simply unplug the unit, wait a few seconds and plug it back in. This will reset
everything and the cleaner will resume normal operation.
Page 3
Thank you for purchasing the Hornady Lock-N-Load® Sonic
Cleaner . ™ Please read these instructions before using this
machine. If you have any questions about this accessory,
contact us at 1-800-338-3220.
The Hornady Lock-N-Load® Sonic Cleaner™ removes carbon residue
from the inside and outside of cartridge cases with high frequency
ultrasonic energy and a specialized cleaning solution. Unlike case
tumblers, the Lock-N-Load
surfaces of cartridge cases as well as the primer pockets. The
Lock-N-Load
®
Sonic Cleaner™ may also be used to clean other small
parts. The Lock-N-Load
steel tank, removable basket, drain trays, de-gas function, adjustable
heating function, a digital timer, a solution usage timer, and suspension
cords for larger items.
The primary function of the Lock-N-Load
chemically and mechanically clean a variety of items. It may or may
not produce “shiny” brass. To create bright and polished brass we
recommend using the Hornady Case Tumbler. Not all carbon buildup
and tarnish may be removed from cases due to the corrosive nature
of some primer residue and/or deep corrosion.
®
Sonic Cleaner™ effectively cleans the inner
®
Sonic Cleaner™ features a 9 liter stainless
®
Sonic Cleaner™ is to
LOCK-N-LOAD HOT TUB
™
ILLUMINATED DISPLAY
Ultrasonic Timer (min:sec)
Actual Solution
Temperature Scale
Solution Target
Temperature
Solution Timer (hrs:min)
De-Gas Function
Ultrasonic Function
Heater Function
DE-GAS FUNCTION
The Hornady Lock-N-Load
®
Sonic Cleaner™ includes a de-gassing
function to remove excess air bubbles from the solution, improving the
effectiveness of the ultrasonic cleaning action. The de-gassing function
cycles the unit on and off, causing air bubbles to release from the
solution and float to the surface.
To turn on the de-gas function, press the FUNCTION button repeatedly
until the symbol above the De-gas label is illuminated. Then turn the unit
on by pressing the ON/OFF button. After de-gassing for 90 seconds, the
unit will return to regular ultrasonic cleaning until the timer expires.
HEATING FUNCTION
The Hornady Lock-N-Load
®
Sonic Cleaner™ includes a heating function
to further enhance the ultrasonic cleaning action. The heating function
may be used on most gun components, however caution should be used
with any heat sensitive items.
The heating function should not be used on painted parts, as the heat
may soften the paint and cause it to flake off during ultrasonic cleaning.
Page 4
Most brass cartridges do not need heat to efficiently clean. Using the
heating function during prolonged cleaning cycles may actually cause
tarnishing to appear.
To turn on the heating function, press the HEAT button until the heater
light turns on. The unit will then heat to the target temperature when the
ultrasonic cleaner is turned on. The heater light will continue to flash
until the solution reaches the target temperature, at which time the light
will turn off.
To adjust the target temperature, press the TEMP button to cycle
through the preset temperature options. Pressing the TEMP button and
then the t button repeatedly will decrease the target temperature.
Always use the lowest temperature setting possible to achieve the
desired cleaning results without overheating the parts.
Extreme caution should be used with the heating function. The cleaning
solution can become very hot and great care should be used when
handling hot parts and solution.
CLEANING INSTRUCTIONS – BRASS CASES
Before you start cleaning cases, make sure all spent primers have
been removed with a full-length die, neck die or the Hornady Universal
De-capping Die (050085). This will greatly enhance the cleaning of
primer pockets.
Place cases in basket and lower into the tank. Add enough water so
the cases are completely submerged but do not exceed the MAX water
line which appears on the side of the basket and tank. Mix solution
according to instructions on bottle.
To set the timer, press the TIME button until the desired cycle time
appears. Pressing the TIME button multiple times will increase the timer
in 5 minute intervals from 5 to 30 minutes. Pressing the t button will
decrease the timer by 1 minute.
The heating function does not need to be used on cartridge brass and
may actually cause tarnishing to appear.
When using new solution, or there appears to be small air bubbles in
the solution, it is recommended to run the de-gassing function prior to
cleaning. This can be done after the parts are added and will remove
many of the air bubbles in the solution, causing the Lock-N-Load
Sonic Cleaner
™
to run more efficiently. See previous instructions in
®
“DE-GAS FUNCTION.”
Press the ON/OFF button to stop or pause a cycle. Pressing the ON/OFF
button again will restart the current cycle.
Check cases periodically to determine appropriate cleaning time. Most
cases will be clean after 10-20 minutes, however, longer cycles may be
needed for cases with heavy carbon buildup or for larger batches.
If running longer than 30 minutes, allow unit to cool for approximately
5 minutes before continuing additional cleaning cycles.
Unplug power cord and drain cleaning solution into tank by lifting and
tilting basket with the cleaned cases. Rinse cleaning solution from the
cases. De-ionized water will minimize water spots on the cases while
they are drying.
To drain the tank, attach the rubber hose to the side discharge fitting
by firmly pressing tube until fully seated. Place the end of the tube into
storage container or drain and open valve on front of unit. Rinse remaining
residue from tank and dry with a soft cloth. Do not pour cleaning solution
out over the sides of the unit as it may damage internal components.
Page 5
CLEANING INSTRUCTIONS – OTHER ITEMS
The previous steps can be used to clean other items such as gun
components, metallic shooting and reloading equipment as well as other
waterproof household items. If you wish to clean sensitive or valuable
items, use distilled water in the tank without any type of detergent or
cleaning solution. Never use heating function on sensitive items or
painted parts. Read and follow instructions on cleaning solution bottles.
Do not use the Hornady One Shot
to clean non-brass items, as it may harm some finishes. Thoroughly
rinse the inside of the Hornady Lock-N-Load
®
Sonic Clean™ Cartridge Case Formula
®
Sonic Cleaner™ tank when
switching cleaning solutions. Oversized items that do not fit in the tank
can be cleaned by partially submerging one end and then rotating and
repeating the cleaning cycles.
CLEANING INSTRUCTIONS – SMALL PARTS TANKS
The Hornady Lock-N-Load
®
Sonic Cleaner™ includes one small parts
cleaning tank (150209) for cleaning smaller items. Additional tanks can
be purchased separately. Up to three small parts tanks can be placed
into the larger tank.
By using the small parts tanks, smaller batches can be used without
wasting cleaning solution in the larger tank. It also allows different
solutions to be used at the same time, For example, one tank can be
filled with Hornady One Shot
the other tanks can be filled with Hornady One Shot
®
Sonic Clean™ Gun Parts Solution while
®
Sonic Clean™
Cartridge Case Solution.
The small parts tank can be used by first filling the larger main tank
with water to the minimum fill line. Place items to be cleaned (cases,
gun components, etc.) into the small parts tank and then fill with
the appropriate cleaning solutions until the items are completely
submerged. Place the small parts tank into the larger tank on either side,
or in the middle. Additional water may be added to the larger tank to
match the level in the small parts tank as long as it does not overfill the
maximum level marked on the tank. The Hornady Lock-N-Load
™
Cleaner
can now be operated as described in the previous sections.
®
Sonic
SOLUTION TIMER FUNCTION
The Lock-N-Load
®
Sonic Cleaner™ includes a solution timer to help
monitor the useful life of the solution. Depending on the cleanliness of
the items being cleaned, the cleaning solution can be used for multiple
batches. However, the solution will eventually become saturated with
contaminants and no longer provide an effective cleaning action. At this
time, the solution needs to be replaced.
The solution timer helps monitor how long each solution mixture has
been used.
To set the solution timer, press the SOLUTION button until the desired
time appears. Pressing the SOLUTION button and then the t button
repeatedly will decrease the solution timer. The timer will automatically
count down when the ultrasonic cleaner is running until the timer
expires. At this time the solution should be replaced.
Note: Do not store solution in tank for extended periods of time as it
may damage or discolor the tank.
Page 6
USING SUSPENSION CORDS
The Hornady Lock-N-Load
®
Sonic Cleaner™ includes 4 suspension
cords to most efficiently clean large items.
If an item is too large for the basket or small parts tank, the suspension
cords may be used. For example, when cleaning a barrel, wrap
suspension cord around each end of the barrel, and then hook the
cord into the tabs in the housing above the tank.
Items may touch the tank, however, this will decrease the ultrasonic
cleaning efficiency. For best results, suspend parts about 1/2 to 1 inch
above the bottom of the tank.
MAINTENANCE
If the unit will not be used for an extended period of time, unplug the
power cord, empty the tank and rinse it with fresh water.
Use a damp towel to remove any chemical residue from the tank.
Use a soft clean towel to dry the surface of the tank and store the
unit in a cool/dry location. Renew cleaning solution often to maintain
the efficiency and performance of the Lock-N-Load
®
Sonic Cleaner.™
Solutions, as with most chemicals, will become spent over time.
Replenish solution when it becomes visibly dirty or if you notice a
decrease in cleaning effectiveness.
WARRANTY
Hornady Manufacturing warrants to you that for one year from the
date of purchase, your Lock-N-Load
®
Sonic Cleaner™ will be free from
defects in material and workmanship. This warranty does not cover
damage caused by normal wear, accidents, abuse or failure to provide
proper care and maintenance.
SPECIFICATIONS
Model Number: 043310
Tank Dimensions:
25.5" x 7.0" x 4.0"
Timer Settings:
0-30 Minutes
Power Supply:
AC 100-120V 60Hz
Power: 500W Total
Frequency: 35,000 Hz
Model Number: 043311
Tank Dimensions:
25.5" x 7.0" x 4.0"
Timer Settings:
0-30 Minutes
Power Supply:
AC 220-240V 50Hz
Power: 520W Total
Frequency: 35,000 Hz
Page 7
OPTIONAL PRODUCTS - SOLD SEPARATELY
ONE SHOT® SONIC CLEAN™
CARTRIDGE CASE FORMULA
Non-toxic and uniquely formulated to
clean brass cases, this 40:1 concentrated
cleaner quickly removes most tarnish,
oxidation and carbon buildup. Designed
specifically for the Hornady
Lock-N-Load
®
Sonic Cleaners.
32 fl oz. No. 043355
Gallon No. 043356
®
™
ADDITIONAL SMALL
PARTS TANK
6.7" x 4.7" x 3.2"
(1.6 Liters/1.7 Quarts)
No. 150209
ONE SHOT
®
SONIC CLEAN™
GUN PARTS FORMULA
Cleans all gun parts and is safe for all
firearms finishes. This 40:1 concentrated
cleaner quickly removes carbon, dirt,
grease and powder residue. Designed
specifically for the Hornady
Lock-N-Load
®
Sonic Cleaners.
®
™
32 fl oz. No. 043360
Gallon No. 043361
ADDITIONAL
PLASTIC BASKET
11.0" x 6.0" x 4.0"
No. 150207
110V/220V 12-2012
P.O. Box 18 48 • Grand Island, NE 68802-1848
(308 ) 382-1390 • www.hornady.com
Loading...