Hornady GS-1000 User Manual
AUTO OFF :
This unit comes with an auto-off feature to conserve battery power.
The scale will automatically turn off after approximately four minutes of
inactivity.
Hornady Electronic Scale
Instruction Manual
Model GS-1000
CAUT ION:
Do not place more than the capacity of the scale on the weighing platform.
Abuse of this type can cause damage to the scale and void the warranty.
This scale is a sensitive electronic instrument. Avoid vibrations, strong
electrical or magnetic elds, and rapid changes in humidity or temperature
as they can adversely affect accuracy.
CARE AND MAI NTEN ANCE :
• Avoid lengthy exposure to extreme heat or cold. To achieve optimum
functioning, allow this unit to acclimatize.
• Allow scale a minimum of thirty seconds to warm up before calibration to
allow internal components to stabilize.
• Keep this product clean. Dust, dirt, and moisture can adversely affect the
reliability and accuracy of this scale.
• Vibrations, air currents and proximity to other electronic equipment may
affect accuracy of this product. Avoid disturbing the environmental conditions
when weighing. Be sure weighing is done with scale on a at surface in a
sheltered area.
• Handle with care. Although this product is durable, rough treatment may
permanently damage the internal sensor.
Congratulations on your selection of a quality Hornady product.
With proper care and use, this product will provide years of
dependable service. Hornady is committed to providing products
that t your needs, manufactured to the highest of quality standards.
If you have any comments or suggestions concerning this product
please mail them to:
Hornady Manufacturing
P.O. Box 1848
Grand Island, NE 68802-1848 USA
www.hornady.com
Please read all the operating instructions to ensure the best performance
from your Hornady Electronic Scale.
CAPACITY/ACCURACY:
1000grain/65grams x 0.1grain/0.01gram
POWER SOURCE:
Four “AA” alkaline batteries or 120 Volt AC adapter
(output DC 6V 100mA)
BATTERY INSERTION:
1. Turn scale upside down and locate battery compartment cover.
2. Push tab toward compartment cover. Lift cover off.
3. Insert four “AA” alkaline batteries; ensure that battery polarities
are aligned properly.
4. Replace battery compartment cover and secure.
5. The scale is now ready for use.
Note: Do not use excessive force in removing or replacing battery
compartment cover.
KEY PAD FUNCTIONS:
ON/OFF/ZERO Key:
a)
Press and hold to turn unit on or off.
b)
Once unit is on, this key operates the tare function. Press to compensate for
the weight of weighing tray or other object.
MODE /CAL Key :
a)
Press and hold to begin calibration procedure (see Calibration Procedure).
b)
Press and release to change weight unit, i.e., from grams to grains.
CALI BRATIO N:
Important: always allow a minimum of thirty seconds for the scale to stabilize.
During prolonged periods of use repeat this procedure at regular intervals for
optimum accuracy.
Note: Any attempt by the end user to internally calibrate the scale will void
warranty.
DIGITAL AUTO CALIBRATION PROCEDURE:
1.
Place scale on a at surface in a sheltered area.
2
. Turn scale on by pressing
thirty seconds.
3. Press and hold
the display will show ashing weight reading which indicates the correct
weight that must be placed on the tray.
4.
At this time, please gently place the correct calibration weight in the center
of the tray.
5.
If no errors occur, the scale will go into the second point calibration. The
display will show “
weight reading which indicates the correct weight that must be placed on
the tray. Now please gently place the correct calibration weight in the center
of the tray.
6.
If no errors occur, the display will show “
three seconds later, which means it is in the weighing state, the process of
calibration is accomplished If the display shows “CAL E”, which means the
calibration failed, please try again.
ON/OFF
key. Allow unit to stabilize for at least
CAL
key until the display shows “
CAL 2
”, press ON/OFF key, the display will show a ashing
CAL 1
CAL L
”, and followed by “
”, press
ON/OFF
CAL F
key,
”
OPERATION:
1. Place scale on a at surface in a sheltered area.
2. Press and hold the ON/OFF/ZERO button to turn the scale on.
3. Open platform lid and place tray on weighing platform. (You may also
place objects directly on the weighing platform.)
4. Allow the scale to stabilize for at least 30 seconds. When initially
turned on, the scale will read 8888 before returning to zero.
5. Gently place object(s) to be weighed in the weighing tray. Do not
overload.
6. Wait for reading to stabilize.
7. Read weight.
8. To change weighing units (from grams to grains) press the
MODE/CAL key.
FEATURES:
DIGITAL AUTO CALIBRATION:
Allows for convenient user digital calibration from the keypad.
POWER UP TEST:
When the unit is initially turned on, all segments of the display will appear.
This will remain for approximately 3 seconds. The scale will then reset to
zero. This is an internal self-test procedure.
RIGH T RE ADIN G IN DICATI ON:
A right facing arrow will appear on the right side of the display to indicate
the weighing mode currently in use. When weight is placed on the tray, a
down facing arrow on the left side of the display will disappear while the
scale stabilizes and will reappear once the stable weight reading is
achieved.
OVER LOAD :
When a load that exceeds this unit’s capacity is applied to the weighing
platform, an E (error) will appear on the display. Remove this load immediately. The unit should then return to normal operation unless damage has
occurred.
(continued)
Loading...