Horizon Hobby Radian Instruction Manual

Radian

Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di Istruzioni

EN

As the user of this product, you are solely responsible for operating in a man­ner that does not endanger yourself and others or result in damage to the
product or the property of others.

• Always keep a safe distance in all directions around your model to avoid
collisions or injury. This model is controlled by a radio signal subject to
interference from many sources outside your control. Interference can cause
momentary loss of control.

• Always operate your model in open spaces away from full-size vehicles,
traffi c and people.

• Always carefully follow the directions and warnings for this and any optional
support equipment (chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and anything electrical out of the
reach of children.

• Always avoid water exposure to all equipment not specifi cally designed and

protected for this purpose. Moisture causes damage to electronics.

• Never place any portion of the model in your mouth as it could cause serious
injury or even death.

• Never operate your model with low transmitter batteries.

• Always keep aircraft in sight and under control.

• Always use fully charged batteries.

• Always keep transmitter powered on while aircraft is powered.

• Always remove batteries before disassembly.

• Always keep moving parts clean.

• Always keep parts dry.

• Always let parts cool after use before touching.

• Always remove batteries after use.

• Always ensure failsafe is properly set before fl ying.

• Never operate aircraft with damaged wiring.

• Never touch moving parts.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product
literature, visit www.horizonhobby.com and click on the support tab for this product.

Meaning of Special Language:

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high

probability of superfi cial injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product
correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to oper­ate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by
children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by
Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warn­ings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

Safety Precautions and Warnings

14

+

AGE RECOMMENDATION:
Not for children under 14
years. This is not a toy.

WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace your Spektrum receiver found

in a Horizon Hobby product, always purchase from Horizon Hobby, LLC or a Horizon Hobby authorized dealer to en­sure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards,
but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with
DSM or Spektrum.

2

EN

To register your product online, visit www.e-fl iterc.com

Box Contents

Quick Start Information

Transmitter

Setup

Blank (Acro) Model

Servo Reversing:
Rudder: Reverse
Elevator: Reverse

Aileron: Reverse

DO NOT Reverse Throttle

Dual Rates

Dual Rates: 100% / 70%

Hi Rate Low Rate

Ele

S=12mm
T=12mm

S=9mm
T=9mm

Rud

X=40mm
W=40mm

X=25mm
W=25mm

Center of

Gravity (CG)

2 1/2 inches (63mm) back

from leading edge at the root.

Flight Timer

Setting

7-10 minutes

Table of Contents

31.0 oz
(880 g)

1140mm (44.7 in)

2000mm (78.7 in)

Specifi cations

Motor: 480B BL Outrunner Motor;

960Kv Reverse Shaft PKZ4716

Installed

ESC: 30A Brushless ESC

(EFLA1031)

Installed

Servo: Mini Servo (3W) with Arms,

Short Lead PKZ1060

Installed

Receiver: Spektrum™ AR400

4-Channel Sport Receiver
(SPMAR400)

Installed

Recommended Battery:

1300mAh 3S 11.1V 20C Li-Po with
EC3 Connector (EFLB13003S20)

Required to

Complete

Recommended Battery Charger:

3-cell Li-Po battery balancing
charger

Required to

Complete

Recommended Transmitter:

Full-Range 4 channel (or more)

2.4GHz with Spektrum

™

DSM2®/DSMX® technology with
adjustable Dual Rates.

Required to

Complete

T

551 sq in
(35.5 sq dm)

Prefl ight ..........................................................................................4

Model Assembly .............................................................................4

Control Horn and Servo Arm Settings ..............................................5

Transmitter and Receiver Binding ....................................................6

Battery Installation and ESC Arming ................................................7

Center of Gravity (CG) ....................................................................8

Control Direction Test ....................................................................8

Flying Tips and Repairs ...................................................................9

Post Flight ....................................................................................10

Motor Service ...............................................................................10

Troubleshooting Guide ..................................................................11

AMA National Model Aircraft Safety Code ......................................12

Limited Warranty ..........................................................................13

Contact Information ......................................................................14

FCC Information ............................................................................14

IC Information ...............................................................................14

Compliance Information for the European Union ............................14

Replacement Parts ........................................................................51

Optional Parts ...............................................................................51

3

EN

Model Assembly

Tail Installation

1. Slide the horizontal stabilizer (A) into the slot of the fuselage.

2. Center the horizontal stabilizer and then secure into place with the 4

included pieces of tape (B).

3. Connect the clevis to the elevator control horn (C) as shown.

A

Prefl ight

1 Remove and inspect contents.
2 Read this instruction manual thoroughly.
3 Charge the fl ight battery.
4 Fully assemble the airplane.
5 Install the fl ight battery in the aircraft (once it has been fully charged).
6 Check the Center of Gravity (CG).
7 Apply Dual Rate values to your transmitter

8 Bind the aircraft to your transmitter.

9 Make sure linkages move freely.
10 Perform the Control Direction Test with the transmitter.
11 Adjust fl ight controls and transmitter.
12 Perform a radio system Range Test.
13 Find a safe open area to fl y.
14 Plan fl ight for fl ying fi eld conditions.

C

B

Connecting a Clevis

1.

2.

3.

4.

5.

6.

• Pull the tube from the clevis to the linkage.

• Carefully spread the clevis, then insert the clevis pin into the desired
hole in the control horn.

• Move the tube to hold the clevis on the control horn.

Control Surface Centering

TIP

TIP

1

2

3

After assembly and transmitter setup, confi rm that the control surfaces
are centered. If the control surfaces are not centered, mechanically
center the control surfaces by adjusting the linkages.

If adjustment is required, turn the clevis on the linkage to change the
length of the linkage between the servo arm and the control horn.

After binding a transmitter to the aircraft receiver, set the trims and
sub-trims to 0, then adjust the clevises to center the control surfaces.

4

EN

Model Assembly Continued

Wing Installation

1. Slide the wing tube (A) into the fuselage.

2. Install the left and right wing over the wing tube until seated into the wing
slot of the fuselage.

3. Secure the wings to the fuselage using the included 2 screws (B) as shown.

Disassemble in reverse order.

Control Horn and Servo Arm Settings

Horns Arms

Elevator

Rudder

More control throw Less control throw

The table to the right shows the factory settings for the control horns and servo
arms. Fly the aircraft at factory settings before making changes.

After fl ying, you may choose to adjust the linkage positions for the desired
control response. See the table to the right.

2

3

5

EN

Transmitter and Receiver Binding

Bind Plug Installation

BIND PLUG

Binding is the process of programming the receiver to recognize the GUID
(Globally Unique Identifi er) code of a single specifi c transmitter. You need to
‘bind’ your chosen Spektrum

™

DSM2®/DSMX® technology equipped aircraft

transmitter to the receiver for proper operation.

IMPORTANT: Before binding a transmitter, read the Transmitter Setup section
of this manual to ensure that your transmitter is properly programmed for this
aircraft.

Binding Procedure

IMPORTANT: The included AR400 receiver has been programmed for
operation specifi cally for this aircraft. Refer to the receiver manual for cor­rect setup if the receiver is replaced or is used in another aircraft.

Read the transmitter instructions for binding to a receiver (location of
transmitter’s Bind control). Please visit www.bindnfl y.com for a com-

plete list of compatible transmitters.

CAUTION: When using a Futaba® transmitter with a Spektrum DSM

module, you must reverse the throttle channel and rebind. Refer to your
Spektrum module manual for binding and failsafe instructions. Refer to
your Futaba transmitter manual for instructions on reversing the throttle
channel.

1. Make sure the transmitter is powered off.

2. Move the transmitter controls to neutral (fl ight controls: rudder,
elevators and ailerons) or to low positions (throttle, throttle trim).**

3. Install a bind plug in the receiver bind port.

4. Connect the fl ight battery to the ESC. The ESC will produce a series
of sounds. 3 short tones confi rm that the LVC is set correctly for the
ESC. The orange bind LED on the receiver will begin to fl ash rapidly.

5. Power on the transmitter while holding the transmitter bind button
or switch. Refer to your transmitter’s manual for binding.

6. When the receiver binds to the transmitter, the orange bind light
on the receiver will turn solid and the ESC will produce ascending
tones. The tones indicate the ESC is armed, provided the throttle
stick and throttle trim are low enough to trigger arming.

7. Remove the bind plug from the bind port.

8. Safely store the bind plug (some owners attach the bind plug to their
transmitter using two-part loops and clips).

9. The receiver should retain the binding instructions received from the
transmitter until another binding is done.

* The throttle will not arm if the transmitter’s throttle control is not put at
the lowest position. If you encounter problems, follow the binding instruc­tions and refer to the transmitter troubleshooting guide for other instruc­tions. If needed, contact the appropriate Horizon Product Support offi ce.

**Failsafe

If the receiver loses transmitter communication, the failsafe will activate.
When activated, the airplane controls return to the neutral position estab­lished during step 2 of the binding procedure.

6

EN

Battery Installation and ESC Arming

Battery Selection

We recommend the E-fl ite® 1300mAh 11.1V 3S 20C Li-Po battery
(EFLB13003S20). Refer to the Optional Parts List for other recommended
batteries. If using a battery other than those listed, the battery should be within
the range of capacity, dimensions and weight of the E-fl ite Li-Po battery packs
to fi t in the fuselage. Be sure the model balances at the recommended CG.

1. Lower the throttle and throttle trim to the lowest settings. Power on the
Transmitter, then wait 5 seconds.

2. Carefully lift the canopy hatch (B) to remove.

3. Install a fully charged battery (C) and secure it into place using the hook an
loop strap (D). See the Adjusting the Center of Gravity instructions for more
information.

4. Connect the battery to the ESC (the ESC is now armed).

• The ESC will sound a series of tones (refer to step 6 of the binding
instructions for more information).

• An LED will light on the receiver.

If the ESC sounds a continuous double beep after the fl ight battery is
connected, recharge or replace the battery.

5. Reinstall the canopy hatch.

D

CAUTION: Always

keep hands away from
the propeller. When
armed, the motor will turn
the propeller in response
to any throttle movement.

C

B

1

2

3

4

7

EN

Center of Gravity (CG)

The CG location is measured from the leading edge of the wing at the root.
This CG location has been determined with the recommended Li-Po battery
(EFLB13003S20) installed all the way forward in the battery compartment.

2-1/2 inches
(63mm)

back from the
leading edge at
the root.

Control Direction Test

Move the controls on the transmitter to make sure the aircraft control
surfaces move in the proper direction.

Transmitter

Command

Aircraft Reaction

Elevator

Up Elevator

Command

Down

Elevator

Command

Rudder

Stick

Left

Stick
Right

8

EN

Flying Tips and Repairs

Consult local laws and ordinances before choosing a fl ying location.

Range Check your Radio System

Before you fl y, range check the radio system. Refer to your specifi c transmitter
instruction manual for range test information.

Hand Launch

Set your dual rate switches to low rate. Hold the aircraft fuselage under the
wing and gradually increase the throttle to ¾. Launch the aircraft into the wind
with the wings level. Allow the aircraft to climb to a comfortable altitude.

Flying

Always choose a wide-open space for fl ying your aircraft. It is recommended
that you fl y at a designated RC fl ying fi eld. Always avoid fl ying near houses,
trees, wires and buildings. Avoid fl ying in areas where there are many people,
such as parks, schoolyards, or soccer fi elds.

In Flight Trimming

During your fi rst fl ight, trim the aircraft for level fl ight at 1/2 throttle. Make
small trim adjustments with your transmitter’s trim switches to straighten the
aircraft’s fl ight path.

After landing, adjust the linkages mechanically to account for trim changes and
then reset the trims to neutral. Ensure the aircraft will fl y straight and level
with no trim or sub-trim.

Landing

For your fi rst fl ights with the recommended battery pack (EFLB13003S30), set
your transmitter timer or a stopwatch to 7 minutes. After 7 minutes, land the
aircraft. Adjust your timer for longer or shorter fl ights once you have fl own the
model. If at any time the motor pulses, land the aircraft immediately to
recharge the fl ight battery. See the Low Voltage Cutoff (LVC) section for more
details on maximizing battery health and run time.

Make sure to land into the wind. Due to the high lifting effi ciency of the sail­plane design, landing requires a large landing area. While on your downwind
leg, remember that the sailplane glides much better than other aircraft. You
will need to setup for landing lower and with a more shallow descent than you
may be used to. As you are on approach for landing, ensure that the model is
descending slowly, but also not accelerating. Maintain this descent and speed,
and, as the model nears the ground (approximately 6 inches (15 cm)), slowly
apply a small amount of up elevator. Before the aircraft touches down, always
fully decrease throttle to avoid damage to the propeller, motor, ESC or other
components.

NOTICE: If a crash is imminent, reduce the throttle and
trim fully. Failure to do so could result in extra dam­age to the airframe, as well as damage to the ESC and
motor.

NOTICE: After any impact, always ensure the receiver
is secure in the fuselage. If you replace the receiver,
install the new receiver in the same orientation as the
original receiver or damage may result.

NOTICE: Crash damage is not covered under warranty.

NOTICE: When you are fi nished fl ying, never leave the

aircraft in direct sunlight or in a hot, enclosed area
such as a car. Doing so can damage the aircraft.

Low Voltage Cutoff (LVC)

When a Li-Po battery is discharged below 3V per cell, it will not hold a charge.
The ESC protects the fl ight battery from over-discharge using Low Voltage
Cutoff (LVC). Before the battery charge decreases too much, LVC removes
power supplied to the motor. Power to the motor pulses, showing that some
battery power is reserved for fl ight control and safe landing.

Disconnect and remove the Li-Po battery from the aircraft after use to prevent
trickle discharge. Charge your Li-Po battery to about half capacity before stor­age. During storage, make sure the battery charge does not fall below 3V
per cell. LVC does not prevent the battery from over-discharge during storage.

NOTICE: Repeated fl ying to LVC will damage the battery.

Tip: Monitor your aircraft battery’s voltage before and after fl ying by using a

Li-Po Cell Voltage Checker (EFLA111, sold separately).

Repairs

Thanks to the Z-Foam™ material in this aircraft, repairs to the foam can be
made using virtually any adhesive (hot glue, regular CA, epoxy, etc). The hori-

zontal tail is not made of the same material, so use only foam-compatible
CA on the horizontal tail.

When parts are not repairable, see the Replacement Parts List for ordering by
item number. For a listing of all replacement and optional parts, refer to the list
at the end of this manual.

NOTICE: Use of CA accelerant on your aircraft can damage paint. DO NOT
handle the aircraft until accelerant fully dries.

WARNING:

Always decrease
throttle at propeller
strike.

Wind

9

EN

Motor Service

Post Flight

1

Disconnect the fl ight battery from the ESC (Required for Safety

and battery life).
2 Power OFF the transmitter.
3 Remove the fl ight battery from the aircraft.
4 Recharge the fl ight battery.

5 Repair or replace all damaged parts.

6

Store the fl ight battery apart from the aircraft and monitor the
battery charge.

7

Make note of the fl ight conditions and fl ight plan results, planning for
future fl ights.

J

K

C

EE

G

B

A

9.75 X 7.5

CAUTION: Always disconnect the fl ight battery before performing
motor service.

Disassembly

1. Remove the 2 screws (A) and spinner (B) from the spinner backplate (C).

2. Remove the propeller nut (D), backplate from the prop adapter (E). You will

need a tool to loosen the spinner nut.

3. Push the propeller pins (F) from the spinner backplate to remove the
propeller blades (G).

4 Remove the set screw (H) from the prop adapter and remove it from the

motor shaft.

5. Remove the 3 cowl screws (J) from the motor mount/cowling (K) and
remove it from the fuselage.

6. Remove the 4 screws (L) and motor (M) from the motor mount/cowling.

7. Disconnect the motor wires from the ESC wires.

Assembly

Assemble in reverse order.

• Correctly align and connect the motor wire colors with the ESC wires.

• The propeller size numbers (9.75x 7.5) must face forward toward the nose

of the aircraft for correct propeller operation.

• A tool is required to tighten the lock nut on the collet.

Not all wires are shown.

H

D F

L

10

EN

Problem Possible Cause Solution

Aircraft will not re­spond to throttle but
responds to other
controls

Throttle not at idle and/or throttle trim too high Reset controls with throttle stick and throttle trim at lowest setting
Throttle servo travel is lower than 100% Make sure throttle servo travel is 100% or greater

Throttle channel is reversed Reverse throttle channel on transmitter
Motor disconnected from ESC Make sure motor is connected to the ESC

Extra propeller noise
or extra vibration

Damaged propeller and spinner, collet or motor Replace damaged parts
Propeller is out of balance Balance or replace propeller
Prop nut is too loose Tighten the prop nut
Spinner is not tight or fully seated in place Inspect spinner to ensure it is fully seated

Reduced fl ight time
or aircraft under­powered

Flight battery charge is low Completely recharge fl ight battery
Propeller installed backwards Install propeller with numbers facing forward

Flight battery damaged Replace fl ight battery and follow fl ight battery instructions
Flight conditions may be too cold Make sure battery is warm before use
Battery capacity too low for flight conditions Replace battery or use a larger capacity battery

Aircraft will not Bind
(during binding) to
transmitter

Transmitter too near aircraft during binding process

Move powered transmitter a few feet from aircraft, disconnect and reconnect
fl ight battery to aircraft

Aircraft or transmitter is too close to large metal
object, wireless source or another transmitter

Move aircraft and transmitter to another location and attempt binding again

The bind plug is not installed correctly in the bind port Install bind plug in bind port and bind the aircraft to the transmitter
Flight battery/transmitter battery charge is too low Replace/recharge batteries
Bind switch or button not held long enough during

bind process

Power off transmitter and repeat bind process. Hold transmitter bind
button or switch until receiver is bound

Aircraft will not con­nect (after binding)
to transmitter

Transmitter too near aircraft during connecting
process

Move powered transmitter a few feet from aircraft, disconnect and reconnect
fl ight battery to aircraft

Aircraft or transmitter is too close to large metal
object, wireless source or another transmitter

Move aircraft and transmitter to another location and attempt connecting again

Bind plug left installed in bind port Rebind transmitter to the aircraft and remove the bind plug before cycling power
Aircraft bound to different model memory

(ModelMatch

TM

radios only)

Select correct model memory on transmitter

Flight battery/Transmitter battery charge is too low Replace/recharge batteries
Transmitter may have been bound to a different air-

craft using different DSM protocol

Bind aircraft to transmitter

Control surface does
not move

Control surface, control horn, linkage or servo
damage

Replace or repair damaged parts and adjust controls

Wire damaged or connections loose Do a check of wires and connections, connect or replace as needed
Transmitter is not bound correctly or the incorrect

airplanes was selected

Re-bind or select correct airplanes in transmitter

Flight battery charge is low Fully recharge fl ight battery
BEC (Battery Elimination Circuit) of the ESC is

damaged

Replace ESC

Controls reversed Transmitter settings are reversed

Perform the Control Direction Test and adjust the controls on transmitter
appropriately

Motor power pulses
then motor loses
power

ESC uses default soft Low Voltage Cutoff (LVC) Recharge fl ight battery or replace battery that is no longer performing
Weather conditions might be too cold Postpone flight until weather is warmer
Battery is old, worn out, or damaged Replace battery
Battery C rating might be too small Use recommended battery

Troubleshooting Guide

11

EN

AMA National Model Aircraft Safety Code

Effective January 1, 2014

A. GENERAL

A model aircraft is a non-human-carrying aircraft capable of sustained fl ight
in the atmosphere. It may not exceed limitations of this code and is intended
exclusively for sport, recreation, education and/or competition. All model fl ights
must be conducted in accordance with this safety code and any additional
rules specifi c to the fl ying site.

1. Model aircraft will not be fl own:
(a) In a careless or reckless manner.
(b) At a location where model aircraft activities are prohibited.

2. Model aircraft pilots will:
(a) Yield the right of way to all man carrying aircraft.
(b) See and avoid all aircraft and a spotter must be used when appropriate.
(AMA Document #540-D.)
(c) Not fl y higher than approximately 400 feet above ground level within
three (3) miles of an airport, without notifying the airport operator.
(d) Not interfere with operations and traffi c patterns at any airport, heliport
or seaplane base except where there is a mixed use agreement.
(e) Not exceed a takeoff weight, including fuel, of 55 pounds unless in
compliance with the AMA Large Model Aircraft program. (AMA
Document 520-A.)
(f) Ensure the aircraft is identifi ed with the name and address or AMA
number of the owner on the inside or affi xed to the outside of the
model aircraft. (This does not apply to model aircraft fl own indoors).
(g) Not operate aircraft with metal-blade propellers or with gaseous boosts
except for helicopters operated under the provisions of AMA Document
#555.
(h) Not operate model aircraft while under the infl uence of alcohol or while
using any drug which could adversely affect the pilot’s ability to safely
control the model.
(i) Not operate model aircraft carrying pyrotechnic devices which explode
or burn, or any device which propels a projectile or drops any object
that creates a hazard to persons or property.

Exceptions:

• Free Flight fuses or devices that burn producing smoke and are

securely attached to the model aircraft during fl ight.

• Rocket motors (using solid propellant) up to a G-series size may

be used provided they remain attached to the model during fl ight.
Model rockets may be fl own in accordance with the National
Model Rocketry Safety Code but may not be launched from
model aircraft.

• Offi cially designated AMA Air Show Teams (AST) are authorized to

use devices and practices as defi ned within the Team AMA
Program Document (AMA Document #718).
(j) Not operate a turbine-powered aircraft, unless in compliance with the
AMA turbine regulations. (AMA Document #510-A).

3. Model aircraft will not be fl own in AMA sanctioned events, air shows or

model demonstrations unless:
(a) The aircraft, control system and pilot skills have successfully
demonstrated all maneuvers intended or anticipated prior to the
specifi c event.
(b) An inexperienced pilot is assisted by an experienced pilot.

4. When and where required by rule, helmets must be properly worn and

fastened. They must be OSHA, DOT, ANSI, SNELL or NOCSAE approved or
comply with comparable standards.

B. RADIO CONTROL

1. All pilots shall avoid fl ying directly over unprotected people, vessels,
vehicles or structures and shall avoid endangerment of life and property
of others.

2. A successful radio equipment ground-range check in accordance with
manufacturer’s recommendations will be completed before the fi rst fl ight
of a new or repaired model aircraft.

3. At all fl ying sites a safety line(s) must be established in front of which all
fl ying takes place (AMA Document #706.)
(a) Only personnel associated with fl ying the model aircraft are allowed at
or in front of the safety line.
(b) At air shows or demonstrations, a straight safety line must be
established.
(c) An area away from the safety line must be maintained for spectators.
(d) Intentional fl ying behind the safety line is prohibited.

4. RC model aircraft must use the radio-control frequencies currently allowed
by the Federal Communications Commission (FCC). Only individuals
properly licensed by the FCC are authorized to operate equipment on
Amateur Band frequencies.

5. RC model aircraft will not operate within three (3) miles of any pre-existing
fl ying site without a frequency-management agreement (AMA Documents
#922 and #923.)

6. With the exception of events fl own under offi cial AMA Competition
Regulations, excluding takeoff and landing, no powered model may be
fl own outdoors closer than 25 feet to any individual, except for the pilot
and the pilot’s helper(s) located at the fl ight line.

7. Under no circumstances may a pilot or other person touch a model aircraft
in fl ight while it is still under power, except to divert it from striking an
individual.

8. RC night fl ying requires a lighting system providing the pilot with a clear
view of the model’s attitude and orientation at all times. Hand-held illumi­ nation systems are inadequate for night fl ying operations.

9. The pilot of a RC model aircraft shall:
(a) Maintain control during the entire fl ight, maintaining visual contact
without enhancement other than by corrective lenses prescribed for
the pilot.
(b) Fly using the assistance of a camera or First-Person View (FPV) only
in accordance with the procedures outlined in AMA Document #550.
(C) Fly using the assistance of autopilot or stabilization system only in
accordance with the procedures outlined in AMA Document #560.

Please see your local or regional modeling association’s guidelines for proper, safe
operation of your model aircraft.

12

EN

Limited Warranty

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the
product purchased (the “Product”) will be free from defects in materials and
workmanship at the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii)
damage due to acts of God, accident, misuse, abuse, negligence, commercial
use, or due to improper use, installation, operation or maintenance, (iii)
modifi cation of or to any part of the Product, (iv) attempted service by
anyone other than a Horizon Hobby authorized service center, (v) Product not
purchased from an authorized Horizon dealer, or (vi) Product not compliant
with applicable technical regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER
WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY
ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE
REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be
that Horizon will, at its option, either (i) service, or (ii) replace, any Product
determined by Horizon to be defective. Horizon reserves the right to inspect
any and all Product(s) involved in a warranty claim. Service or replacement
decisions are at the sole discretion of Horizon. Proof of purchase is required
for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM
IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY
OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the
liability of Horizon exceed the individual price of the Product on which
liability is asserted. As Horizon has no control over use, setup, fi nal assembly,
modifi cation or misuse, no liability shall be assumed nor accepted for any
resulting damage or injury. By the act of use, setup or assembly, the user
accepts all resulting liability. If you as the purchaser or user are not prepared
to accept the liability associated with the use of the Product, purchaser is
advised to return the Product immediately in new and unused condition to the
place of purchase.

Law

These terms are governed by Illinois law (without regard to confl ict of law
principals). This warranty gives you specifi c legal rights, and you may also
have other rights which vary from state to state. Horizon reserves the right to
change or modify this warranty at any time without notice.

WARRANTY SERVICES
Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty
support or service. Once assembly, setup or use of the Product has been
started, you must contact your local distributor or Horizon directly. This will
enable Horizon to better answer your questions and service you in the event
that you may need any assistance. For questions or assistance, please visit our
website at www.horizonhobby.com, submit a Product Support Inquiry, or call
the toll free telephone number referenced in the Warranty and Service Contact
Information section to speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online Service
Request submission process found on our website or call Horizon to obtain a
Return Merchandise Authorization (RMA) number. Pack the Product securely
using a shipping carton. Please note that original boxes may be included,
but are not designed to withstand the rigors of shipping without additional
protection. Ship via a carrier that provides tracking and insurance for lost or

damaged parcels, as Horizon is not responsible for merchandise until it arrives
and is accepted at our facility. An Online Service Request is available at http://
www.horizonhobby.com/content/_service-center_render-service-center. If you
do not have internet access, please contact Horizon Product Support to obtain
a RMA number along with instructions for submitting your product for service.
When calling Horizon, you will be asked to provide your complete name, street
address, email address and phone number where you can be reached during
business hours. When sending product into Horizon, please include your RMA
number, a list of the included items, and a brief summary of the problem. A
copy of your original sales receipt must be included for warranty consideration.
Be sure your name, address, and RMA number are clearly written on the
outside of the shipping carton.

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with
a LiPo battery, please contact the appropriate Horizon Product Support
offi ce.

Warranty Requirements
For Warranty consideration, you must include your original sales receipt
verifying the proof-of-purchase date. Provided warranty conditions have

been met, your Product will be serviced or replaced free of charge. Service or
replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service
Should your service not be covered by warranty, service will be

completed and payment will be required without notifi cation or estimate
of the expense unless the expense exceeds 50% of the retail purchase
cost. By submitting the item for service you are agreeing to payment of the

service without notifi cation. Service estimates are available upon request. You
must include this request with your item submitted for service. Non-warranty
service estimates will be billed a minimum of ½ hour of labor. In addition you
will be billed for return freight. Horizon accepts money orders and cashier’s
checks, as well as Visa, MasterCard, American Express, and Discover cards.
By submitting any item to Horizon for service, you are agreeing to Horizon’s
Terms and Conditions found on our website http://www.horizonhobby.com/
content/_service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the
country of use and ownership. If received, a non-compliant Product will
not be serviced. Further, the sender will be responsible for arranging
return shipment of the un-serviced Product, through a carrier of the
sender’s choice and at the sender’s expense. Horizon will hold non­compliant Product for a period of 60 days from notifi cation, after which it
will be discarded.

13

EN

Compliance Information for the European Union

Contact Information

Country of Purchase Horizon Hobby Phone Number/Email Address Address

United States of

America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/

RequestForm/

4105 Fieldstone Rd

Champaign, Illinois, 61822 USA

Horizon Product Support

(Product Technical Assistance)

www.quickbase.com/db/

bghj7ey8c?a=GenNewRecord

888-959-2305

Sales

[e-mail]

888-959-2305

United Kingdom

Service/Parts/Sales:

Horizon Hobby Limited

[e-mail]

Units 1–4 , Ployters Rd, Staple Tye

Harlow, Essex, CM18 7NS, United Kingdom

[phone]

Germany

Horizon Technischer Service [e-mail]

Christian-Junge-Straße 1

25337 Elmshorn, Germany

Sales: Horizon Hobby GmbH [phone]

France

Service/Parts/Sales:

Horizon Hobby SAS

[e-mail] 11 Rue Georges Charpak

77127 Lieusaint, France

[phone]

China

Service/Parts/Sales:

Horizon Hobby – China

[e-mail] Room 506, No. 97 Changshou Rd.

Shanghai, China 200060

[phone]

FCC Information

Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

CAUTION: Changes or modifi cations not expressly approved by the party

responsible for compliance could void the user’s authority to operate the
equipment.

This product contains a radio transmitter with wireless technology which has been tested
and found to be compliant with the applicable regulations governing a radio transmitter
in the 2.400GHz to 2.4835GHz frequency range.

IC Information

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over
to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and
the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city offi ce, your
household waste disposal service or where you purchased the product.

EFL Radian BNF Basic (EFL4750)

EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions

of the R&TTE and EMC Directive.

A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.

14

Part # | Nummer
Numéro | Codice

enoizircseDnoitpircseDgnubierhcseBnoitpircseD

EPKZ1017

Propeller Blades: Radian Propeller: Radian Radian - Pales Eliche: Radian

PKZ1018

Prop Adapter & Spinner Set: Radian

Luftschraubenmitnehmer und Spinner:
Radian

Radian - Set adaptateur d’hélice &
cône

Set adattatore elica & ogiva: Radian

PKZ1060

Mini Servo (3W) with Arms, Short
Lead

Mini Servo, 3 adrig, kurzes Kabel

Mini Servo (3 fi ls) avec Palonniers,
câble court

Servocomando mini (3W) con
braccetti, cavo corto

PKZ4713

Canopy: Radian Parkzone Kabinenhaube:Radian Radian -Verrière Parafi amma con viti: Radian

PKZ4714

Firewall w/Screws: Radian Motorschott : Radian Radian - Cloison Pare-feu avec Vis Parafi amma con viti: Radian

PKZ4716

PKZ 480 Outrunner Brushless Motor:
Radian

Parkzone Radian BL Motor 480b

Radian - Moteur Brushless 480 à cage
tournante

PKZ 480 motore outrunner
brushless: Radian

PKZ5422

Pushrods with Clevis: Radian Parkzone Gestängeset: Radian Pro Radian - Tringlerie avec chapes Squadrette con forcelle: Radian

PKZ4725

Tail Wing Set: Radian Parkzone Leitwerk : Radian Radian - Empennages Horizontal Set ali di coda: Radian

EFLA1030

30-Amp Pro SB Brushless ESC E-fl ite 30A Pro SB Regler Contrôleur Brushless 30A Pro 30A Pro SB ESC brushless

EFL6910

Decal Sheet: Brave

E-fl ite Dekorbogen: Brave

Radian - Planche de décoration Decal Sheet: Brave

EFL4701

Bare Fuselage: Radian BNF E-fl ite Rumpf ohne Kabinenhaube Radian BNF - Fuselage nu Fusoliera vuota: Radian BNF

EFL4702

Wing with spar: Radian BNF E-fl ite Tragfl äche mit Holm: Radian BNF Radian BNF - Aile avec clé Ala con longherone: Radian BNF

EFL4703

Decal Sheet: Radian BNF Dekoborgen: Radian BNF Radian BNF - Planche de décoration Decalcomanie: Radian BNF

Replacement Parts • Ersatzteile • Pièces de rechange • Pezzi di ricambio

Part # | Nummer
Numéro | Codice

enoizircseDnoitpircseDgnubierhcseBnoitpircseD

EFLA250

Park Flyer Tool Assortment, 5 pc Park Flyer Werkzeugsortiment, 5 teilig Assortiment d'outils park fl yer, 5pc Park Flyer assortimento attrezzi, 5 pc

EFLAEC302

EC3 Battery Connector, Female (2) EC3 Akkukabel, Buchse (2) Prise EC3 femelle (2pc)

EC3 Connettore femmina x
batteria (2)

EFLAEC303

EC3 Device/Battery Connector,
Male/Female

EC3 Kabelsatz, Stecker/Buchse Prise EC3 male/femelle

EC3 Connettore batteria maschio/
femmina

EFLB22003S50

11.1V 3S 30C 3200MAH Li-Po 11.1V 3S 30C 3200mAh LiPo 11.1V 3S 30C 3200MAH Li-Po 11.1V 3S 30C 3200MAH Li-Po

DYNC2020A

Prophet Sport Duo 50W x 2 AC
Battery Charger

Dynamite Prophet Sport Duo 50W x 2
AC Ladegerät, EU

Chargeur Prophet Sport Duo 50W x 2 AC

Prophet Sport Duo 50W x 2 AC
caricabatteria

DYNC2010CA

Prophet Sport Plus 50W AC DC
Charger

Dynamite Ladegerät Prophet Sport
Plus 50W AC/DC EU

Chargeur Prophet Sport Plus 50W ACDCCaricabatterie Prophet Sport Plus

50W AC DC

EFLA111

Li-Po Cell Voltage Checker Li-Po Cell Voltage Checker Testeur de tension d’éléments Li-Po Voltmetro verifi ca batterie LiPo

DYN1405

Li-Po Charge Protection Bag,
Large

Dynamite LiPoCharge Protection Bag
groß

Sac de charge Li-Po, grand modèle.

Sacchetto grande di protezione per
carica LiPo

DYN1400

Li-Po Charge Protection Bag,
Small

Dynamite LiPoCharge Protection Bag
klein

Sac de charge Li-Po, petit modèle

Sacchetto piccolo di protezione per
carica LiPo

DX6i DSMX 6-Channel Transmitter Spektrum DX6i DSMX 6-Kanal Sender Emetteur DX6i DSMX 6 voies DX6i DSMX Trasmettitore 6 canali

DX6 DSMX 6-Channel Transmitter Spektrum DX6 DSMX 6-Kanal Sender Emetteur DX6 DSMX 6 voies DX6 DSMX Trasmettitore 6 canali

DX7 DSMX 7-Channel Transmitter Spektrum DX7 DSMX 7 Kanal Sender Emetteur DX7 DSMX 7 voies DX7 DSMX Trasmettitore 7 canali
DX9 DSMX 9-Channel Transmitter Spektrum DX9 DSMX 9 Kanal Sender Emetteur DX9 DSMX 9 voies DX9 DSMX Trasmettitore 9 canali
DX18 DSMX 18-Channel

Transmitter

Spektrum DX18 DSMX 18 Kanal
Sender

Emetteur DX18 DSMX 18 voies DX18 DSMX Trasmettitore 18 canali

Optional Parts • Optionale Bauteile • Pièces optionnelles • Pezzi opzionali

51

© 2015 Horizon Hobby, LLC.

E-fl ite, DSM, DSM2, DSMX, the DSMX logo, Bind-N-Fly, Z-Foam, ModelMatch, EC3, Celectra and the Horizon Hobby logo

are trademarks or registered trademarks of Horizon Hobby, LLC.

The Spektrum trademark is used with permission of Bachmann Industries, Inc.

Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan.

All other trademarks, service marks and logos are property of their respective owners.

Patents pending.

http://www.e-fl iterc.com/

Created 07/15 48332

EFL4750