Horizon Hobby ECX03056 Instruction Manual

Congratulations on your purchase of the ECX® Axe™ Monster Truck
This 1/10-scale model introduces you to the sport of RC driving.

Herzlichen Glückwunsch zum Kauf des ECX Axe Monster Truck
Dieses 1/10 Scale Model öffnet Ihnen die Welt des RC Car Sports.

Nous vous félicitons pour l’achat de l’ECX Axe Monster Truck
Ce modèle 1/10 vous initie à la conduite RC.

Congratulazioni per l’acquisto di questo Axe Monster Truck
Questa vettura in scala 1/10 vi introdurrà nel mondo dei modelli RC.

INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE DI ISTRUZIONI

1/10 2WD ELECTRIC MONSTER TRUCK

ECX03056

®

AXE

™

2

EN

AXE MONSTER TRUCK

™

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product
literature, visit http://www.horizonhobby.com and click on the support tab for this product.

As the user of this product, you are solely responsible for operating in a
manner that does not endanger yourself and others or result in damage to
the product or property of others.

This model is controlled by a radio signal subject to interference from
many sources outside your control. This interference can cause momen­tary loss of control, so it is advisable to always keep a safe distance in
all directions around your model as this margin will help avoid collisions
or injury.

• Never operate your model with low transmitter batteries.

• Always operate your model in open spaces away from full-size
vehicles, traffic and people.

• Never operate the model in the street or in populated areas for any
reason.

• Carefully follow the directions and warnings for this and any optional
support equipment (chargers, rechargeable battery packs, etc.) you use.

• Keep all chemicals, small parts and anything electrical out of the
reach of children.

• Never lick or place any portion of the model in your mouth as it could
cause serious injury or even death.

• Exercise caution when using tools and sharp instruments.

• Take care during maintenance as some parts may have sharp edges.

• Immediately after using your model, do NOT touch equipment such
as the motor, electronic speed control and battery, because they
generate high temperatures. You may burn yourself seriously touching
them.

• Do not put fingers or any objects inside rotating and moving parts, as
this may cause damage or serious injury.

• Always turn on your transmitter before you turn on the receiver in the
car. Always turn off the receiver before turning your transmitter off.

• Keep the wheels of the model off the ground when checking the
operation of the radio equipment.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate
the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability.
Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not
intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the
instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow
all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create
a high probability of superfi cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure

authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility

and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.

TABLE OF CONTENTS

SAFETY PRECAUTIONS AND WARNINGS

Water-resistant Vehicle with Waterproof Electronics ................................3

Specifi cations ...............................................................................................3

Components .................................................................................................4

Quick Start....................................................................................................4

Vehicle Preparations ....................................................................................4

Installing the Battery.................................................................................4

Transmitter Controls ..................................................................................5

Installing Transmitter Batteries ................................................................5

Binding ......................................................................................................6

Changing the Throttle Limit ......................................................................6

Getting Started..........................................................................................6

Operation......................................................................................................7

When You Are Finished................................................................................7

Motor Care ...................................................................................................7

Maintenance ................................................................................................8

Setting the Gear Mesh..............................................................................8

Electronic Speed Control (ESC) .................................................................8

Electrical Layout ........................................................................................8

Shock Cleaning..........................................................................................9

Ride Height Adjustment ............................................................................9

Shock Absorber Parts ...................................................................................9

Fasteners ......................................................................................................9

Troubleshooting Guide ...............................................................................10

Limited Warranty .......................................................................................11

Warranty and Service Contact Information ...............................................12

FCC Information..........................................................................................12

IC Information.............................................................................................12

Parts Diagram...................................................................................... 46–48

Replacement Parts .....................................................................................49

Optional Parts.............................................................................................50

Recommended Parts ..................................................................................50

3

EN

AXE MONSTER TRUCK

™

SPECIFICATIONS

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with a
combination of waterproof and water-resistant components to allow
you to operate the product in many “wet conditions,” including puddles,
creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely
waterproof and your vehicle should NOT be treated like a submarine.
The various electronic components used in the vehicle, such as the
Electronic Speed Control (ESC) and servo(s) are waterproof, however,
most of the mechanical components are water-resistant and should not
be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well
as the contacts in the electrical cables, will be susceptible to corrosion if
additional maintenance is not performed after running in wet conditions.
To maximize the long-term performance of your vehicle and to keep
the warranty intact, the procedures described in the “Wet Conditions
Maintenance” section below must be performed regularly if you choose
to run in wet conditions. If you are not willing to perform the additional
care and maintenance required, then you should not operate the vehicle
in those conditions.

CAUTION: Failure to exercise caution while using this
product and complying with the following precautions could

result in product malfunction and/or void the warranty.

General Precautions

• Read through the wet conditions maintenance procedures and make
sure that you have all the tools you will need to properly maintain
your vehicle.

• Not all batteries can be used in wet conditions. Consult the battery
manufacturer before use. Do not use Li-Po batteries in wet conditions.

• The included transmitter is not waterproof or water-resistant. If
using a different transmitter than the one included, consult your
transmitter's manual or the manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may be
present.

• Do not operate your vehicle where it could come in contact with salt
water (ocean water or water on salt-covered roads), contaminated or
polluted water. Salt water is very conductive and highly corrosive, so
use caution.

• Even minimal water contact can reduce the life of your motor if it
has not been certified as water-resistant or waterproof. If the motor
becomes excessively wet, apply very light throttle until the water is
mostly removed from the motor. Running a wet motor at high speeds
may rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor. The
additional resistance of operating in water causes excess strain.
Alter the gear ratio by using a smaller pinion or larger spur gear. This
will increase torque (and motor life) when running in mud, deeper
puddles, or any wet conditions that will increase the load on the
motor for an extended period of time.

Wet Conditions Maintenance

• Remove the battery pack(s) and dry the contacts. If you have an air
compressor or a can of compressed air, blow out any water that may
be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud
and dirt off with a garden hose. Avoid rinsing the bearings and
transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle
and help remove any water that may have gotten into small crevices
or corners.

• Spray the bearings, drive train, fasteners and other metal parts with a
water-displacing light oil or lubricant. Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may
continue to drip for a few hours.

• Increase the frequency of disassembly, inspection and lubrication of
the following:

• Front and rear axle hub assembly bearings.

• All transmission cases, gears and differentials.

• Motor—clean with an aerosol motor cleaner and re-oil the
bushings with lightweight motor oil.

Transmitter (SPMSTX200)

Frequency 2.4GHz
Battery AA × 4

Servo (SPMS603)

Power Supply 4.8V~6V
Output Torque 41.66 oz (3 kg-cm)
Operating Speed 0.23sec/60 degrees of travel
Size 55.6 × 18 × 30mm

Electronic Speed Control (ESC) (DYNS2210)

Input Voltage 5–7 cell NiMH/2S LiPo 12T–34T
5–7 cell NiMH/2S-3S LiPo 35T–55T
12T Motor Limit

Electric Capacity Forward 60A/360A
Electric Capacity Reverse 30A/180A
BEC Voltage 6V
Size 37.5 × 37.0 × 18.0mm
Weight 1.41 oz (40 g)

4

EN

AXE MONSTER TRUCK

™

EN

INSTALLING THE BATTERY

1. Turn the battery clips (A) clockwise to remove the
battery strap (B).

2. Install a fully charged battery.

3. Install the battery strap.

4. Turn the battery clips counterclockwise to secure the

battery strap.

Place foam blocks (ECX236005) in front of the battery so the
weight of the battery increases rear traction or in back of the
battery to increase steering response.

CAUTION: Connecting the battery to the ESC with

reversed polarity will cause damage to the ESC, the
battery or both. Damage caused by incorrectly connecting
the battery is not covered under warranty.

A

B

QUICK START

Please read the entire manual to gain a full understanding of the vehicle, fi ne-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.

2. Charge a battery for the vehicle. Refer to the included
charging warnings and instructions for battery charging
information.

3. Install the AA batteries in the transmitter. Only use alka­line or rechargeable batteries.

4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds
for the ESC to initialize. Always power the transmitter ON before
the vehicle and power it OFF after the vehicle has been powered
OFF.

6. Check the steering and throttle control directions. Verify that the
servos are moving in the correct direction.

7. Drive your vehicle.

8. Perform any necessary maintenance.

VEHICLE PREPARATIONS

COMPONENTS

2.4GHZ DIGITAL
RADIO SYSTEM

• ECX® Axe™ Monster Truck (ECX03056)

• Spektrum™ STX2® 2-CH Transmitter (SPMSTX200)

• AA (4) Batteries

• Dynamite® 550 12T Motor (DYNS1223)

• Dynamite® 60A WP Brushed ESC (DYNS2210)

• Spektrum

™

SRX200 2-CH Receiver (SPMSRX200)

5

EN

AXE MONSTER TRUCK

™

INSTALLING TRANSMITTER BATTERIES

CAUTION: If using rechargeable batteries, charge only

rechargeable batteries. Charging non-rechargeable batteries may
cause the batteries to burst, resulting in injury to persons and/or damage
to property.

This transmitter requires 4 AA batteries.

1. Remove the battery cover from the transmitter.

2. Install the batteries as shown.

3. Install the battery cover.

CAUTION: Risk of explosion if battery is replaced by an incorrect

type. Dispose of used batteries according to national regulations.

TRANSMITTER CONTROLS

1

2

11

3

4

8

7

9

6

10

5

12

1. Steering Wheel Controls direction (left/right) of the model

2. Throttle Trigger Controls speed and direction (forward/brake/

reverse) of the model

3. ON/OFF Switch Turns the power ON/OFF for the transmitter

4. Throttle Limiting Switch Adjusts the throttle limit from 50%, 75%,

and 100%

5. TH Rate Adjusts the end point of the throttle

6. TH Trim Adjusts the throttle neutral point

7. TH REV Reverses the function of the speed control when pulled back

or pushed forward

8. ST REV Reverses the function of the steering when the wheel is

turned left or right

9. ST Trim Adjusts the steering center point

10. ST Rate Adjusts the end point of the steering

11. Antenna Transmits the signal to the model

12. Indicator Lights

• Solid red lights—indicates radio connectivity and adequate

battery power

• Flashing red lights—indicates the battery voltage is critically
low. Replace batteries

6

EN

AXE MONSTER TRUCK

™

GETTING STARTED

1. Power on the transmitter.

3. Perform a test of the transmitter’s control of the vehicle

with the vehicle’s wheels off the ground.

4. Start driving slowly, and, if the vehicle does not go straight,
adjust the steering trim dial on the transmitter.

IMPORTANT: Seat the motor brushes by driving smoothly on a fl at
surface during use of the fi rst battery charge. Properly seating the motor
brushes will increase the life and performance of the motor.

2. Power on the ESC.

2.4GHZ DIGITAL
RADIO SYSTEM

BINDING

Binding is the process of programming the receiver to recognize the GUID
(Globally Unique Identifi er) code of a single specifi c transmitter. The
STX2® transmitter and SPMSRX200 receiver are bound at the factory. If
you need to rebind, follow the instructions below.

1. With the vehicle on a fl at, level surface, insert the Bind Plug in the
BIND port on the receiver.

2. Connect a fully charged battery pack to the ESC.

3. Power on the ESC. The red LED fl ashes, indicating the receiver is

in bind mode.

4. Center the ST TRIM and TH TRIM dials on the transmitter.

5. Turn the steering wheel to Full Right. Power the transmitter on

while holding the steering wheel to the Right.

6. Release the steering wheel when the receiver LED stops fl ashing.

7. Remove the Bind Plug, then power off the receiver to save the

settings.

8. Power off the transmitter.

9. Remove the bind plug and store it in a convenient place.

10. You must rebind when:

• Different failsafe positions are desired e.g., when throttle or
steering reversing has been changed.

• Binding the receiver to a different transmitter.

CHANGING THE THROTTLE LIMIT

Beginner Mode

Throttle Limiting Switch: 50%

• Best for learning the basic functions of left, right, stop, brake and
reverse

• For use in smaller areas

• Longest battery life

Best Overall Performance (Default)

Throttle Limiting Switch: 75%

• Great top speed and acceleration

• Easier to accelerate in desired direction, especially on loose surfaces
when compared to Maximum Speed setup

• Run time is greatly increased over Maximum Speed setup with
minimal impact to top speed

Maximum Speed

Throttle Limiting Switch: 100%

• More capable of popping and holding wheelies

• Higher top speeds and maximum acceleration

Throttle Limit Switch

7

EN

AXE MONSTER TRUCK

™

• ALWAYS turn on your transmitter before you turn on the receiver
in the vehicle. Always power off the receiver before turning your
transmitter off.

• ALWAYS operate your vehicle in a wide open area. Operating the
vehicle in a small space or indoors can cause overheating at low
speeds. Operating at low speed increases heat in the electronic
speed control (ESC). Overheating can damage the vehicle and failure
may result.

OPERATION

WHEN YOU ARE FINISHED

• Seat the motor brushes by driving smoothly on a flat surface during

use of the first battery charge. Failing to do so can greatly

reduce motor performance and functional life.

• Prolong motor life by preventing overheating conditions.
Undue motor wear results from frequent turns, stops and starts,
pushing objects, driving in deep water and tall grass, and driving

continuously up hill. Allow the motor to cool completely

before running the vehicle.

• Over-temperature protection is installed on the ESC to prevent
circuit damage, but cannot protect the motor from driving against
heavy resistance.

MOTOR CARE

1. Power off the ESC. 2. Disconnect the battery.

4. Remove the battery from the vehicle.

3. Power off the transmitter.

5. Recharge the battery.

8

EN

AXE MONSTER TRUCK

™

ELECTRICAL LAYOUT

For correct operation, Channels 1 and 2
must be used as shown in the wiring diagram.
The motor can be disconnected from the ESC
at the connectors in the wiring.

MAINTENANCE

SETTING THE GEAR MESH

The gear mesh has already been set at the factory. Setting the gear mesh
is only necessary when changing motors or gears.

You must remove the vehicle’s gear cover (A) to make this adjustment.
Proper gear mesh (how the gear teeth meet) is important to the

performance of the vehicle. When the gear mesh is too loose, the spur
gear could be damaged by the pinion gear of the motor. If the mesh is too
tight, speed could be limited and the motor and ESC will overheat.
Set the gear mesh by following these simple steps:

1. Loosen the 2 motor screws (B).

2. Put a small piece of paper (C) between the pinion and spur gears.

3. Push the gears together while tightening the motor screws.

4. Rotate the gears to remove the paper. The gearing should move a

small amount.

5. Reinstall the gear cover.

Part # Description

A DYNS1223

Dynamite™ 550 12T
Motor

B

Battery (sold separately)

C SPMS603*

Waterproof Steering
Servo

D SPMSRX200

Receiver

E DYNS2210

Waterproof Electronic
Speed Control (ESC)

F

Channel 1

G

Channel 2

*OEM part only. Replacement, please use
part SPMSS6170.

ELECTRONIC SPEED CONTROL (ESC)

Programming: The ESC comes with one jumper pre-installed:
BATT: Li-Po confi guration.

The throttle setting without the jumper indicates Throttle/Brake/Reverse
(F/Br/R). Always use this setting for this vehicle.

To change the battery type to Ni-MH, disconnect the jumper from the
default port and connect it to the Ni-MH port. If the jumper is removed
from the BATT port, the default setting is Li-Po mode. Power off the ESC,
then power it back on.

If the jumpers are lost or not installed, the ESC will default to F/Br/R and
BATT: Li-Po.

NOTICE: Only use the Ni-MH port when using Ni-MH batteries. Using
the Ni-MH port with a Li-Po battery can cause serious damage to the
battery and is unsafe.

A

C

B

EC3EC3

A

B

C

D

G

F

Operation Tone

Start up One short tone, followed by one long tone.
Low Voltage Cut-Off When low voltage cuttoff is reached, the vehicle will slow and emit a continuous tone.
Low Voltage at Start Up When a low battery is plugged in and powered on, the vehicle will emit two low tones and power off.

E

9

EN

AXE MONSTER TRUCK

™

SHOCK CLEANING

Oil-fi lled shocks will require regular maintenance due to the oil breaking
down or getting dirty. This maintenance should be performed after about
every 3 to 5 hours of use, depending on the conditions that the vehicle is
used in.

• Remove the shock from the vehicle.

• Remove the cap from the shock body and dispose of fluid.

• Disassemble the shock. Clean thoroughly with a plastic- and
electronic-safe degreaser (DYNE50001). Dry parts before assembly.

• Re-assemble the shock and refill the shock body with silicone fluid
(30 weight recommended).

• Slowly move the shaft and piston up and down to remove air bubbles.

• Move the piston to the midway point of the body and install the cap.

• Wipe off any overflowing fluid.

• When properly filled, the piston should rebound about 3/8 in (9.5mm)
after being pushed in fully.

• Re-install the shock on the vehicle.

RIDE HEIGHT ADJUSTMENT

Ride height is an adjustment that affects the way the vehicle jumps, turns
and goes over bumps. Drop one end of the vehicle from approximately 6
inches (152 mm) in height onto a fl at surface. When dropping the front of
the vehicle, after the vehicle settles, make sure the front arms are equal
and parallel to the fl at surface. Do the same with the rear to make sure
both arms are parallel with the fl at surface.

Lowering the front ride height increases steering, but decreases traction.
Lowering the rear ride height increases traction, but decreases steering.

Part # Description

ECX1036 Shock Body Set
ECX1037 Shock Caps, Pistons
ECX1038 Shock Parts Set
ECX1039 Front Shock Shaft (2)
ECX1040 Rear Shock Shaft (2)
ECX1041 Front Shock Springs (2)
ECX1042 Rear Shock Springs (2)
ECX1043 Shock O-Ring Set

No. Description

TAPPING
BINDER HEAD
M3x10mm

TAPPING
BINDER HEAD
M3x12mm

TAPPING
FLAT HEAD
M3x15mm

TAPPING
FLAT HEAD
M3x12mm

TAPPING
FLAT HEAD
M3x10mm

TAPPING
BINDER HEAD
M3x18mm

TAPPING
FLAT HEAD
M2x16mm

TAPPING
BINDER HEAD
M3x16mm

No. Description

WASHER
5x7x0.5mm

E-CLIP E2.5

LOCK WASHER

FLANGED
LOCK NUT M4

WASHER
3x8x0.5mm

LOCK NUT M3

WASHER
2x7x0.5mm

SET SHAFT
SCREW
M3x13mm

No. Description

SETSCREW
M3x3mm

SETSCREW
M3x12mm

STEP SCREW
M3x0.5x13.4mm

STEP SCREW
M3x0.5x10.5mm

BUTTON
HEX
M2.5x4mm

BUTTON
HEX
M2.5x8mm

STEP SCREW
M3x0.5x7.4mm

No. Description

BINDER
HEAD
M3x8mm

BINDER
HEAD
M3x12mm

BINDER
HEAD
M3x20mm

BINDER
HEAD
M3x25mm

FASTENERS

ECX1043
ECX1037

ECX1041

ECX1037

ECX1043

ECX1036

ECX1038

ECX1038

ECX1043

ECX1037

ECX1037

ECX1038

ECX1037

ECX1042

ECX1040

ECX1057

ECX1037

ECX1043

ECX1038

ECX1039

ECX1036

ECX1038

ECX1038

ECX1037

ECX1057

REAR FRONT

SHOCK ABSORBER PARTS

10

EN

AXE MONSTER TRUCK

™

TROUBLESHOOTING GUIDE

Problem Possible Cause Solution

Short run time

Battery damaged/not charged Check/change battery
Motor dirty Check/clean

Sluggish action

Motor dirty Check/clean
Bind in drivetrain Clean/adjust

Vehicle battery is not charged Replace/recharge
Controls reversed ST. REV or TH. REV Change switch position
Motor/ESC overheat Over-geared for the driving environment Install smaller pinion on the motor

Does not operate

Transmitter batteries low Replace/recharge

Transmitter powered off Power on

ESC powered off Power on

Vehicle battery is not charged Replace/recharge

Dual-rate (D/R) steering and/or throttle knobs on

transmitter are turned counterclockwise

Adjust dual-rate (D/R) steering or throttle knobs clockwise
to desired setting

Poor range

Transmitter batteries low Replace/recharge

Receiver antenna damaged Check/repair/replace

The system will not connect

Transmitter and receiver too near each other Move transmitter 3.3–9.8ft (1–3m) from receiver

Transmitter and receiver too near large metal

objects (vehicles, etc.)

Move away from large metal objects (vehicles, etc.)

Throttle trim out of center on transmitter

Set throttle trim on transmitter to zero. Turn off and on
transmitter and vehicle

Receiver accidentally put in bind mode so receiver

is no longer bound

Rebind transmitter and receiver

The receiver goes into failsafe
mode a short distance away from
the transmitter

Check the receiver antenna to be sure it is not cut

or damaged

Make sure the antenna is in the antenna tube Contact
Horizon Product Support

The receiver quits responding
during operation

Low battery voltage Completely recharge battery

Loose or damaged wires or connectors between

battery and receiver

Do a check of the wires and connection between battery
and receiver. Repair or replace wires and/or connectors

Receiver and transmitter are not
bound

Transmitter accidentally put in bind mode, ending

bind to receiver

Bind transmitter to receiver

Vehicle moves forward or back­ward without input from user

Throttle trim on transmitter not centered Adjust throttle trim on transmitter to neutral point

Car does not drive straight Steering trim on transmitter not centered

Adjust steering trim on transmitter so the vehicle drives
straight

No steering or lack of steering

Steering dual-rate (D/R) on transmitter not

adjusted correctly

Adjust steering dual-rate (D/R) knob on transmitter
clockwise to desired steering throw

Servo failed Contact Horizon Product Support

No throttle or lack of throttle

Throttle dual-rate (D/R) on transmitter not

adjusted correctly

Adjust throttle dual-rate (D/R) knob on transmitter

clockwise to desired steering throw
ESC failed Contact Horizon Product Support
Motor failed Contact Horizon Product Support

Clicking noise in transmission
area

Dirt or rocks in spur gear Remove gear cover and inspect. If necessary, replace gear
Motor moved away from spur gear Reset gear mesh

11

EN

AXE MONSTER TRUCK

™

LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the
product purchased (the “Product”) will be free from defects in materials
and workmanship at the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage,
(ii) damage due to acts of God, accident, misuse, abuse, negligence,
commercial use, or due to improper use, installation, operation or
maintenance, (iii) modifi cation of or to any part of the Product, (iv)
attempted service by anyone other than a Horizon Hobby authorized
service center, (v) Product not purchased from an authorized Horizon
dealer, or (vi) Product not compliant with applicable technical regulations
or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO
OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS
ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED
THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE
PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall
be that Horizon will, at its option, either (i) service, or (ii) replace, any
Product determined by Horizon to be defective. Horizon reserves the right
to inspect any and all Product(s) involved in a warranty claim. Service
or replacement decisions are at the sole discretion of Horizon. Proof of
purchase is required for all warranty claims. SERVICE OR REPLACEMENT
AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION
OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER
SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE,
STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF
HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Further, in no event shall the liability of Horizon exceed the individual
price of the Product on which liability is asserted. As Horizon has no
control over use, setup, fi nal assembly, modifi cation or misuse, no liability
shall be assumed nor accepted for any resulting damage or injury. By
the act of use, setup or assembly, the user accepts all resulting liability.
If you as the purchaser or user are not prepared to accept the liability
associated with the use of the Product, purchaser is advised to return
the Product immediately in new and unused condition to the place of
purchase.

Law

These terms are governed by Illinois law (without regard to confl ict of
law principals). This warranty gives you specifi c legal rights, and you may
also have other rights which vary from state to state. Horizon reserves the
right to change or modify this warranty at any time without notice.

WARRANTY SERVICES
Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty
support or service. Once assembly, setup or use of the Product has been
started, you must contact your local distributor or Horizon directly. This
will enable Horizon to better answer your questions and service you in
the event that you may need any assistance. For questions or assistance,

please visit our website at www.horizonhobby.com, submit a Product
Support Inquiry, or call the toll free telephone number referenced in the
Warranty and Service Contact Information section to speak with a Product
Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online
Service Request submission process found on our website or call Horizon
to obtain a Return Merchandise Authorization (RMA) number. Pack the
Product securely using a shipping carton. Please note that original boxes
may be included, but are not designed to withstand the rigors of shipping
without additional protection. Ship via a carrier that provides tracking
and insurance for lost or damaged parcels, as Horizon is not responsible
for merchandise until it arrives and is accepted at our facility. An Online
Service Request is available at http://www.horizonhobby.com/content/
service-center_render-service-center. If you do not have internet access,
please contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When calling
Horizon, you will be asked to provide your complete name, street address,
email address and phone number where you can be reached during
business hours. When sending product into Horizon, please include
your RMA number, a list of the included items, and a brief summary of
the problem. A copy of your original sales receipt must be included for
warranty consideration. Be sure your name, address, and RMA number
are clearly written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have
any issue with a Li-Po battery, please contact the appropriate
Horizon Product Support offi ce.

Warranty Requirements
For Warranty consideration, you must include your original sales

receipt verifying the proof-of-purchase date. Provided warranty

conditions have been met, your Product will be serviced or replaced free
of charge. Service or replacement decisions are at the sole discretion of
Horizon.

Non-Warranty Service
Should your service not be covered by warranty, service will

be completed and payment will be required without notifi cation
or estimate of the expense unless the expense exceeds 50% of
the retail purchase cost. By submitting the item for service you are

agreeing to payment of the service without notifi cation. Service estimates
are available upon request. You must include this request with your item
submitted for service. Non-warranty service estimates will be billed
a minimum of ½ hour of labor. In addition you will be billed for return
freight. Horizon accepts money orders and cashier’s checks, as well as
Visa, MasterCard, American Express, and Discover cards. By submitting
any item to Horizon for service, you are agreeing to Horizon’s Terms and
Conditions found on our website http://www.horizonhobby.com/content/
service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant
in the country of use and ownership. If received, a non­compliant Product will not be serviced. Further, the sender
will be responsible for arranging return shipment of the
un-serviced Product, through a carrier of the sender’s choice
and at the sender’s expense. Horizon will hold non-compliant
Product for a period of 60 days from notifi cation, after which it
will be discarded.

10/15

12

EN

AXE MONSTER TRUCK

™

FCC ID: 2AI3D-SS0001

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer­ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.

This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations
governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

FCC INFORMATION

WARRANTY AND SERVICE CONTACT INFORMATION

IC INFORMATION

IC ID: 21682-SSTC9202

This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired opera­tion of the device.

EU Compliance Statement: Horizon Hobby, LLC hereby
declares that this product is in compliance with the
essential requirements and other relevant provisions of the
RED and EMC directives.

A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by
users in the European Union

This product must not be disposed of with other waste.
Instead, it is the user’s responsibility to dispose of their
waste equipment by handing it over to a designated

collections point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and
the environment. For more information about where you can drop off your
waste equipment for recycling, please contact your local city offi ce, your
household waste disposal service or where you purchased the product.

Country of

Purchase

Horizon Hobby Contact Information Address

United States

of America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/

RequestForm/

2904 Research Road

Champaign, Illinois, 61822 USA

Horizon Product Support

(Product Technical Assistance)

[e-mail]

877-504-0233

Sales

[e-mail]

800-338-4639

European Union

Horizon Technischer Service [e-mail]

Hanskampring 9

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH [phone]

46

IT

AXE MONSTER TRUCK

™

9

M3x12

M3x15

M3x15

M3x25

M3X12

M3X10

M3X10

M3X10

M3X12

M3X25

M3X12

M3X12

M3X10

M3X10

M3X12

M3X15

M3X12

M3X12

M3X10

M3X8

M3X10

M3X12

M3X12

21

23

7

13

14

15

15

23

8

18

8

20

19

16

2

13

20

31

31

7

20

20

1

5

12

22

44

45

12

17

13

46

19

7

2

8

7

2

19

3

11

11

30

4

49

29

50

PARTS DIAGRAM | EXPLOSIONSZEICHNUNG |

VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI

1.5 mm

2 mm

RECOMMENDED ITEMS
EMPFOHLENE WERKZEUGE
OUTILS RECOMMANDÉS
ATTREZZI CONSIGLIATI

AXE MONSTER TRUCK

™

47

PARTS DIAGRAM | EXPLOSIONSZEICHNUNG |

VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI

M3X20

M3X12

M3x12

M3x15

M3X15

M3X10

M3X12

M3X12

M3X12

M3X12

M3X12

M3X12

M3X18

M3X10

M3X12

M3X15

M3X3

M2.5X8

M2.5X8

M2.5X4

M3X12

M3X12

M3X18

32

32

36 25 3538 33

39 39

223434

34

34 34

15

36

42

15

33

15

48 3548

1515

33

33

33

33

35 33 35 33

36

38

25

M2X16

M2X16

35

12 Optional

44

45

25

47

43

43

17

43
43

11

13

13

47

25

47

3

19

19

29

21

23

13

31

31

15

28

13

20

22

40 33

29

24

20

20

50

39

6

14

26b

27

26b

27

26a

The slipper clutch can be adjusted
using this locknut (ECX1060). Fully
tighten the locknut, then loosen the
nut two full turns.

Die Rutschkupplung kann durch
diese Stopmutter eingestellt
werden (ECX1060). Ziehen Sie die
Mutter an und drehen Sie dann
volle zwei Umdrehungen zurück.

Il est possible d’ajuster le
sliper par action sur cet écrou
de blocage (ECX1060). Veillez à
serrer l’écrou de blocage à fond.
Ensuite, devissez l’écrou de
deux tours complets.

La frizione può essere regolata
con questo dado autobloccante
(ECX1060). Prima avvitate comple­tamente il dado, poi svitatelo 2 giri.

When installing the wheel, make sure the drive hex is aligned with the drive pin.
When the drive hex is removed, the drive pin can fall out of the axle.

Bitte achten Sie bei der Radmontage darauf, dass die Radachse im Radmitnehmer
sitzt und dass der der Querstift nicht heraus fällt.

Lors de l’installation de la roue, assurez-vous que l’hexagone de roue est aligné avec la goupille
d’entraînement. En cas de démontage de l’hexagone, la goupille peut sortir de l’axe et tomber.

Quando montate le ruote, accertatevi che il trascinatore esagonale sia allineato con la spina
del mozzo ruota. Quando togliete il trascinatore esagonale la spina può sfi larsi dal mozzo.

AXE MONSTER TRUCK

™

48

PARTS DIAGRAM | EXPLOSIONSZEICHNUNG |

VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI

51

52

AXE MONSTER TRUCK

™

49

Part # Description Beschreibung Description Descrizione

1

ECX231022 Short Chassis

Chassis Châssis principal Telaio principale

2

ECX1028 Servo Saver Set

Servo Saver Set Sauve servo Set salvaservo

3

ECX2011

Cover and Rear Mount Set Abdeckung und hinterer Halter Set Capot et fi xations arrières

Copertura e set di montaggio
posteriore

4

ECX1050 Setscrew M3 x 12 (4)

Schrauben Set M3 x 12 (4) Jeu de vis M3 x 12 (4) Grani M3 x 12 (4)

5

ECX236005 Foam Block

Schaum Block Bloc de mousse Spugna distanziale batteria

6 ECX1098

Motor Screw/Washer Set Motor Screw/Washer Set

Set vis/rondelles moteur Viti per il motore/set di rondelle

7

ECX1058 Ball Stud (6)

Kugelkopf (6) Rondelle (6) Sfere uniball (6)

8

ECX1065 Shoulder Screw Set (8)

Passschrauben Set (8) Jeu de vis épaulées (8) Set viti a doppio stadio (8)

9 SPMSRX200

2-Ch Receiver

2 Kanal Empfänger

Récepteur 2 voies Ricevitore

11 ECX231024

Battery Strap, ESC Plate Akkugurt, ESC-Platte

Sangle de batterie, plaque du variateur ESC Fascetta batteria, piastra ESC

12 ECX231002

Rear Bumper Set

Hintere Stossstange Pare-choc arrière Set paraurti posteriore

13 ECX2006

Suspension Arm Mount Set Querlenker Set hinten Jeu de renfort de suspension Supporti braccetti sosp.

14

ECX43015

Right/Left, Premount, Wheel (2): Axe

Rechts/Links, Premount, Rad (2):
Axe

Droite/Gauche, Prémontage, Roue
(2): Axe

Destra/Sinistra, Premount, Ruota
(2): Axe

15

ECX1015 Ball Bearing 5 x 10 x 4mm (8) Kugellager 5 x 10 x 4mm (8)

Roulement à billes 5 x 10 x 4mm (8) Cuscinetto a sfera, 5 x 10 x 4 mm (8)

16

ECX1018 Front Suspension Arm Set

Querlenker Set vorne Jeu de bras de suspension avant Braccetti delle sospensioni anteriori

17

ECX1020 Shock Tower Set

Dämpferbrücke Jeu de support d’amortisseur Supporto ammortizzatori posteriori

18

ECX1035 Front Axle (2)

Radachse vorne (2) Axe de roue avant (2) Mozzi ruota anteriori (2)

19

ECX1044 Hinge Pin Set

Querlenkerbolzen Set Jeu d’axes de suspension Set perni sospensioni

20

ECX1046 Camber, Toe Link Set

Spur- Sturzstangenset

Jeu de biellettes de carrossage et de
pincement

Set tiranteria Camber e convergenza

21

ECX1049 Wheel Pins (4)

Radmitnehmerstifte (4) Goupilles d’entraînement (4) Spine trascinatori ruote (4)

22

ECX1060 M4 Locknut (4)

M4 Stopmutter (4) Ecrous auto-freinés M4 (4) Dadi autobloccanti M4 (4)

23 ECX234000

Caster Block, Steer Block,
RR Hub (2)

Radblock, Steuerblock,
Hinterradnabe (2)

Blocs de roulettes, Bloc de direction,
Corps de fusées arrière (2)

Blocco ruota anteriore, blocco sterzo,
mozzo posteriore (2)

24

ECX1019 Rear Suspension Arm Set

Querlenker Set hinten Jeu de bras de suspension arrière

Braccetti delle sospensioni
posteriori

25

ECX232033 Transmission Case Set

Getriebegehäuse Ensemble carter de transmission Set scatola trasmissione

26a

ECX232000 Long Driveshaft Set, Complete HD (2) Lange Antriebswelle, HD (2) Long arbre de transmission, HD (2) Albero di trasmissione lungo, HD (2)

26b

ECX232002 Long Driveshaft, Plastic Only HD (2)

Lange Antriebswelle, nur Kunststoff
HD (2)

Long arbre de transmission, uniquement
en plastique ultra-résistant (2)

Albero di trasmissione lungo, solo
plastica HD (2)

27

ECX232005 Driveshaft Pivot Ball (4) Antriebswellen Kugelkopf (4) Croisillon de cardan (4) Attacco a sfera semiasse (4)

28 ECX232001

Rear Axle (2) Wellenmitnehmer hinten (2) Axe de roue arriere Attacco a sfera semiasse (4)

29

ECX1045 Button Head Screw 2.5 x 4mm (8)

Rundkopfschraube 2,5 x 4mm (8)

Vis à tête bombée, 2,5 x 4mm (8)

Vite a testa tonda, 2,5 x 4 mm (8)

30 DYNS2210 WP 60A FWD/REV Brushed ESC (ESC) Elektrischer Fahrtenregler (ESC)

Variateur 60A marche av/arr étanche pour
moteur à charbon

Regolatore elettronico di velocità
(ESC) WP

31

ECX1037

Shock Caps, Pistons, Pivot Ball Set

Stoßkappe, Kolben, Schwenkkugel­Set

Ensemble de Capuchons d’amortisseurs,
Pistons, Rotule

Set articolazione a rotula, pistoni,
tappi ammortizzatore

32 ECX231026

Gear Cover Gear Cover Carter de Réducteur Copertura per ingranaggi

33

ECX1022 Transmission Gear Set

Getriebe

Couronne et pignons intermédiaires,
corps et pignons de différentiel

set ingranaggi trasmissione

34

ECX1024 Slipper Clutch Plates, Pads, Spring

Rutschkupplung Teilesatz

Garnitures, plateaux et ressort de
slipper

Piattelli frizione, disco, molla

35

ECX1025 Transmission Idler Shaft, Drive Pins

Hauptgetriebewelle Set

Arbre secondaire de transmission avec
goupilles d’entraînement

Alberino intermedio con spina

36

ECX1026 Transmission Drive Shaft (2)

Getreibeausgangswelle (2) Axe de sortie de différentiel (2) Mozzi Differenziale (2)

37

ECX1052 Washer/Shim Set

Unterlegscheiben

/Shim

Set Jeu de rondelles

/Shim

Set rondelle

/Shim

38

ECX1055 Bearings 10 x 15 x 4mm (2)

Lager 10 x 15 x 4mm (2) Roulements 10 x 15 x 4mm (2) Cuscinetti 10 x 15 x 4mm (2)

39

ECX1059 M3 Locknut (4)

M3 Stopmutter (4) Ecrou auto-freiné M3 (4) Dadi autobloccanti M3 (4)

40 ECX232032

Spur Gear 48P, 93T

Hauptzahnrad

48P, 93T

Couronne

48P, 93T

Corona

48P, 93T

42 DYNS1223

Dynamite 12T 550 Motor Dynamite 12T 550 Motor

Moteur Dynamite 12T 550

Motore a Dynamite 550 12T

43 ECX1048

Body Clip (8) Body Clip (8) Clips Carrosserie (8) Clips per carrozzeria (8)

44 ECX231025

Body Post Set

Körperpfosten-Set Set Plots Carrosserie Set di sostegni per la carrozzeria

45 ECX2009

Body Mount Set Aufnahme Karosseriehalter Set Montage Carrosserie Set di montaggio per la carrozzeria

46 ECX2007

Skid Plate Set Skid Plate Set Set Plaque Chassis Set pistre di protezione

47 ECX2013

Rear Bumper Mount Heckstoßstangenhalterung Support de pare-chocs arrière Supporto bumper posteriore

48 ECX1023

Top Shaft/Spacer Top Shaft/Spacer Set de Goupilles Set di spessori

49 ECX1033

Setscrew M3 x 10 Feststellschraube M3 x 10 Vis de fi xation M3 x 10

Vite di arresto M3 x 10

50 ECX231023 Front Bumper Set

Vordere Stossstange Pare-choc avant Set paraurti anteriore

REPLACEMENT PARTS / ERSATZTEILE /

PIÈCES DE RECHANGE / PEZZI DI RICAMBIO

AXE MONSTER TRUCK

™

50

Part # Description Beschreibung Description Descrizione

51

ECX230042 Body w/ladder, Red/Black

Körper mit Leiter, Rot/Schwarz Corps avec échelle, rouge / noir Corpo con scala, rosso / nero

52

ECX230043 Ladders w/ Hardware

Leitern mit Hardware Echelles avec quincaillerie Scale con hardware

53 ECX1051 M3 × 3mm Set Screw (6)

M3 × 3mm Stellschraube (6) Vis de réglage M3 × 3mm (6) Vite di fermo M3 × 3mm (6)
54 ECX1056 3 × 6 × 2.8mm Bushing (2) Buchse 3x6x2.8mm (2) Bague 3x6x2,8mm (2) Boccole 3x6x2.8mm (2)
55 ECX1057 3mm E-Clip (8) 3mm E-Clip (8) E-Clip 3mm (8) Clip da 3mm (8)
56 ECX1062 3 × 8mm Button Head Screw (10)

Knopfschraube

3 × 8mm (10)

Vis à tête ronde

3 × 8mm (10)

Vite a testa di bottone

3 × 8mm (10)

57 ECX1063

3 × 10mm Self-Tap Button Head
Screw (10)

Selbstschneidend Knopfschraube

3

× 10mm (10)

Auto-taraudage v

is à tête ronde

3 ×

10mm (10)

Autofi lettanti vite a testa di bottone
3 × 10mm (10)

58 ECX1064

3 × 12mm Self-Tap Button Head
Screw (10)

Selbstschneidend Knopfschraube
3 × 12mm (10)

Auto-taraudage v

is à tête ronde

3 × 12mm (10)

Autofi lettanti vite a testa di bottone
3 × 12mm (10)

59 ECX2017

3 × 18mm Self-Tap Button Head
Screw (10)

Selbstschneidend Knopfschraube
3 × 18mm (10)

Auto-taraudage v

is à tête ronde

3 × 18mm (10)

Autofi lettanti vite a testa di bottone
3 × 18mm (10)

60 ECX2018 3 × 16mm Button Head Screw (10)

Knopfschraube

3 × 16mm (10)

Vis à tête ronde

3 × 16mm (10)

Vite a testa di bottone

3 × 16mm (10)

61 ECX2019 3 × 10mm Button Head Screw (10)

Knopfschraube

3 × 10mm (10)

Vis à tête ronde

3 × 10mm (10)

Vite a testa di bottone

3 × 10mm (10)

SPMSTX200 STX2 2CH Transmitter STX2 2-Kanal Fernsteuerung Émetteur STX2 2 voies Trasmittente STX2 2 canali

Part # Description Beschreibung Description Descrizione

RPM73292 Front Spndle Blocks (2), Black; ECX FR Spindelblöcke (2), Schwarz Blocs d’axe avant (2), noirs Blocchi alberino, anteriore (2), nero

RPM70582

Front A-arms, Black; ECX CIR/RUC/
TOR

FR A-Arm (2), Schwarz Bras de commande A avant (2), noirs Bracci di controllo, anteriori (2), nero

RPM73442 HD Caster Blocks, Black; ECX 2wd HD Radblock, Schwarz Blocs de roulettes ultra-résistants, noirs Blocchi ruota anteriore HD, nero

DYN1400 LiPo Charge Protection Bag, Small LiPo Ladeschutztasche, klein

Sac de protection du chargeur
de batterie Li-Po, petit

Borsa di protezione per carica batterie
LiPo, piccola

RPM70462

Rear A-arms (2), Black; ECX Cir/
Ruc/Tor

RR A-Arm (2), Schwarz Bras de commande A arrière (2), noirs Bracci di controllo, posteriori (2), nero

RPM73572 Rear Axle Carriers, Black; ECX 2wd Hinterachsträger, Schwarz Supports d’essieu arrière, noirs Porta asse posteriore, nero
RPM73492 SX-Saver Bellcrank, Black; ECX SX-Saver-Umlenkhebel, Schwarz Levier coudé SX-Saver, noir Leva a squadra SX-Saver, nero

DYNT0500 Startup Tool Set: ECX/VTR/HPI Werkzeug Set: ECX/VTR/HPI

Set d’outils de démarrage pour ECX/
VTR/HPI

Set attrezzi start up: ECX/VTR/HPI

ECX1061 Screw Set (64): 1:10 2WD ALL

ECX Blechschraubenset (64 Stk): Cir/
Ruck/Torm

1/10 2WD - Set de vis (64) Set viti (64): tutte le 1:10 2WD

ECX1095

Aluminum Shock Set Front: 1:10 2WD
Cir/Ruck/Torm

ECX Aluminium-Dämpferset vorne: Cir/
Ruck/Torm

1/10 2WD Cir/Ruck/Torm - Set
d’amortisseurs avant en Aluminium

Set ammortizzatore ant. in allu.: 1:10
2WD Cir/Ruck/Torm

ECX1096

Aluminum Shock Set Rear: 1:10 2WD
Cir/Ruck/Torm

ECX Aluminium-Dämpferset hinten:
Cir/Ruck/Torm

1/10 2WD Cir/Ruck/Torm - Set
d’amortisseurs arrière en Aluminium

Set ammortizzatore post. in allu: 1:10
2WD Cir/Ruck/Torm

ECX1097

Universal Battery Strap (1): 1:10
2WD ALL

ECX Electrix-Akkuhalteband: 7-Zellen­Akku

1/10 2WD - Sangle universelle pour
batterie

Velcro fi ssaggio batteria universale
(1): tutte le 1:10 2WD

ECX331000

Front Shock Tower, Aluminum, 1:10
2WD ALL

ECX Aluminium-Dämpferbrücke vorne:
ECX 1/10 2WD

1/10 2WD - Support d’amortisseurs
avant Aluminium

Torre ammortizzatore ant. in allu.:
tutte le 1:10 2WD

ECX331001

Rear Shock Tower, Aluminum, 1:10
2WD Cir/Ruck/Torm

ECX Aluminium-Dämpferbrücke vorne:
ECX 1/10 2WD

1/10 2WD Cir/Ruck/Torm - Support
d’amortisseurs arrière

Torre ammortizzatore post. in allu:
1:10 2WD Cir/Ruck/Torm

ECX331008

Steering w/Servo Saver, Aluminum:
1:10 2WD ALL

Lenkung mit Servosaver, Aluminium:
1:10 2WD ALL

1:10 2WD - Direction avec sauve-servo,
Aluminum

Sterzo con salvaservo, alluminio:
1:10 2WD (TUTTI I MODELLI)

ECX332000

Wheel Hex, Aluminum, 1:10 2WD
Ruckus/Torment

ECX Aluminum Radmitnehmer: Ruckus/
Torment 1/10 2WD

1/10 2WD Ruckus/Torment - Hexagones
de roue en Aluminium

Esagono ruota, allu.: 1:10 2WD
Ruckus/Torment

ECX334000 Rear Hubs, Aluminum, 1:10 2WD ALL

ECX Aluminum-Radträger hinten: ECX
1/10 4WD

1/10 2WD - Fusées arrière Aluminium Mozzi post., allu.: tutte le 1:10 2WD

ECX334001

Caster Block, Aluminum 1:10 2WD
ALL

ECX Aluminum-Achsschenkelträger:
ECX 1/10 4WD

1/10 2WD - Étriers porte fusée
Aluminium

Caster Block, allu.: tutte le 1:10 2WD

ECX334002

Steering Block, Aluminum, 1:10
2WD ALL

ECX Aluminium-Lenkträger: ECX 1/10
2WD

1/10 2WD - Fusées avant Aluminium

Fusello dello sterzo, allu.: tutte le
1:10 2WD

ECX9001 Metal Gear Set: 1:10 2WD ALL ECX Metallgetriebeset 1/10 2WD - Set de pignons métal

Set ingranaggio in metallo: tutte le
1:10 2WD

Part # Description Beschreibung Description Descrizione

DYN1501 Powerstage Bundle - Stage 1 Powerstage-Bundle - Stufe 1 Pack Powerstage - Étape 1 Powerstage Bundle - Stage 1
DYN1510 Powerstage Bundle - Stage 2 Powerstage-Bundle - Stufe 2 Pack Powerstage - Étape 2 Powerstage Bundle - Stage 2

OPTIONAL PARTS / OPTIONALE TEILE /

LISTE DES OPTIONS / ELENCO PARTI OPZIONALI

RECOMMENDED PARTS / EMPFOHLENE TEILE /

PIÈCES RECOMMANDÉES / PARTI RACCOMANDATE

www.ecxrc.com

ECX03056

®

© 2019 Horizon Hobby, LLC. ECX, the ECX logo, Dynamite, Powerstage, STX2, EC3 and the Horizon Hobby logo are trademarks or
registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc. Axe is a trademark or registered trademark of
Avenger Monster Truck Racing, Inc. and is used under license.
Updated 12/2018 58293.1