Horizon Hobby DX2EQ2UC Users manual

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon
Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm
when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a
little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND
a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral
damage, and serious injury OR create a high probability of superfi cial injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product
before operating. Failure to operate the product correctly can result in damage to the product, personal

property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires

some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result
in injury or damage to the product or other property. This product is not intended for use by children without
direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product
in any way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation
and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to
assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC

authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all
support and warranty with regards, but not limited to, compatibility and performance of counterfeit products
or products claiming compatibility with DSM or Spektrum technology.

NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles and
aircraft. Horizon Hobby disclaims all liability outside of the intended purpose and will not provide warranty
service related thereto.

Warranty Registration

Visit www.spektrumrc.com/registration today to register your product.

SAFETY PRECAUTIONS

• Always ensure all batteries have been properly charged
prior to using the model.

• Always check all servos and their connections prior to each run.

• Never operate your model near spectators, parking areas
or any other area that could result in injury to people or
damage of property.

• Never operate your model during adverse weather
conditions. Poor visibility can cause disorientation and loss
of control of your model.

• Never point the transmitter antenna directly toward the
model. The radiation pattern from the tip of the antenna is
inherently low.

• If at any time during the operation of your model you
observe any erratic or abnormal operation, immediately
stop operation of your model until the cause of the
problem has been ascertained and corrected.

INSTALLING THE BATTERIES

CAUTION: Risk of explosion if battery is replaced

by an incorrect type. Dispose of used batteries

according to national regulations.

CAUTION: If using rechargeable batteries, charge

only rechargeable batteries. Charging non­rechargeable batteries may cause the batteries to burst,
resulting in injury to persons and/or damage to property.

EN

SPEKTRUM DX2E ACTIVE USER GUIDE

1

EN

BATTERY LED MONITOR

Solid Green Battery is good (Above 4V)
Flashing Green Battery voltage is critically low.

Replace batteries (below 4V)

RECEIVER COMPATIBILITY

The DX2E is compatible with all Spektrum
DSM2® receivers.

™

RECEIVER CONNECTION AND IN­STALLATION

Antenna

Throttle Port
Steering Port
Bind Plug

TYPICAL ELECTRIC INSTALLATION

Battery To Motor

Electronic

Speed Control

Receiver

Steering Servo

TYPICAL GAS INSTALLATION

Receiver

DSMR® and

Throttle Servo

Steering Servo

Battery

BINDING A RECEIVER

Binding is the process of programming the receiver to
recognize the GUID (Globally Unique Identifier) code of a
single specific transmitter. When a receiver is bound to a
transmitter, the receiver will only respond to that specific
transmitter. The DX2E and SR310 are bound at the factory,
but if you need to rebind for any reason, please follow these
steps:

1. With the receiver off, insert the bind plug into the BIND
port on the receiver.

2. Power the receiver through any other port. The green
LED will flash continuously, indicating the receiver is in
bind mode.

3. With the steering wheel and throttle trigger in the desired
preset failsafe positions (see the Failsafe section on this
page for more information), press and hold the bind
button and turn on the transmitter. The green LED on the
front of the transmitter will flash within three seconds,
indicating the transmitter is in bind mode. Release the
bind button when the green LED flashes. Continue to
hold the failsafe positions until the binding process is
complete.

Bind Button

4. The LED on the receiver will glow solid when the
transmitter and receiver are bound.

5. Remove the bind plug and store it in a convenient place.

You must rebind when:

• Different failsafe positions are desired e.g., when throttle
or steering reversing has been changed.

• Changing receiver types e.g., changing from a DSM2
receiver to DSMR receiver.

• Binding the receiver to a different transmitter.

FAILSAFE

Failsafe positions are also set during binding. In the unlikely
event that the radio link is lost during use, the receiver will
drive the servos to their preprogrammed failsafe positions
(normally full brakes and straight steering). If the receiver
is turned on prior to turning on the transmitter, the receiver
will enter failsafe mode. When the transmitter is turned on,
normal control is resumed. For more information on setting
the failsafe, refer to the Binding a Receiver section above.

Install the Receiver in your vehicle using double-sided foam
servo tape. Foam servo tape will hold the receiver in place
and help isolate it from vibrations. Mount the antenna up
and away from the vehicle in an antenna tube. The higher up
the antenna is, the better signal it will receive.

CAUTION: Do not cut the antenna.

2 SPEKTRUM DX2E ACTIVE USER GUIDE

SERVO REVERSING

If a right steering command does not result in the wheels
turning right (and vice versa), the channel may need to be
reversed. To reverse a channel, switch the position of the
correlating switch—“N” is for normal, “R” is for reverse.

Reverse Switch
Steering

Reverse Switch
Throttle

EN

THROTTLE TRIM

The throttle trim dial is used to adjust the throttle trim
when the throttle stick is released (neutral position). This is
typically used to adjust the brakes. Rotating the dial causes
the throttle trim (the throttle position at rest) to be changed.

Throttle Trim Dial

THROTTLE LIMITER

The Throttle Limiter switch limits the throttle ouput from
50/70/100%.This is useful for limiting motor ouput on slick or
loose traction tracks or to limit vehicle speeds for new drivers.

Throttle limiter Switch

3-POSITION SWITCH

The 3-Position Switch is used to control a third channel and
is factory preset at -100%/Neutral/100%.

3 position Switch

STEERING TRIM

The steering trim dial is used to adjust the steering trim
when the wheel is centered. Rotating the dial changes the
steering trim (the steering at rest position). Normally, the
steering trim is adjusted until the vehicle tracks straight.

Steering Trim Dial

STEERING RATE AND GAIN CONTROL

Steering rate (also known as dual rate) allows on-the-fly
steering travel adjustments to be made using the ST Rate
dial. Steering rate limits the amount of travel of the steering
servo. The steering rate cannot be greater than 100%.
When the DX2E is bound to a DSMR® AVC® receiver, the
ST RATE knob controls the sensor gain value. Turn the knob
counterclockwise to reduce the gain or clockwise to increase
the gain.

Steering
Rate Dial

CHANGING THE TRAVEL ADJUST
SETTINGS

The travel function supports precise endpoint adjustments in
each direction for the steering and throttle channels.

1. Hold the trigger in the full brake position and the steering wheel
in full right position while powering on the transmitter. The LED
flashes rapidly, indicating the programming mode is active.

2. Throttle End Point: Hold the trigger in the full throttle position.
Turn the TH TRIM knob to adjust the full throttle end point.

3. Brake End Point: Hold the trigger in the full brake position.
Turn the TH TRIM knob to adjust the full brake end point.
Return the trigger to the center position.

4. Left Steering End Point: Hold the steering wheel in the full left
position. Turn the ST TRIM knob to adjust the left end point.

5. Right Steering End Point: Hold the steering wheel in the full
right position. Turn the ST TRIM knob to adjust the right end
point. Return the steering wheel to the center position.

6. Power off the transmitter to save the travel adjust settings.
The minimum Travel is 75%, and the Maximum travel is
150%. The default travel settings are 125% steering and
100% throttle.

IMPORTANT: If the travel is changed on the DX2E, you must
rebind and calibrate AVC® Receivers.

SPEKTRUM DX2E ACTIVE USER GUIDE

3

EN

BLUETOOTH MODULE:

The Optional Bluetooth Module (sold separately) allows
wireless access to the radio application on supported smart
phones or tablets. The application displays a dashboard for a
selected vehicle and allows for easy setting changes and
access to model memory.

1. Make sure the transmitter is off.

2. Remove the back cover plate from the back side of transmitter
by removing one screw.

Tip: A small flat blade screwdriver may be used to gently pry
the back cover plate off once the screw is removed.

3. Firmly seat the Bluetooth Module into the back of the DX2E and secure with the screw removed in step 2.

For more information on the Bluetooth Module vist www.spektrumrc.com

SPEEDOMETER MODULE:

The Optional Speedometer Module (sold separately) provides an easy-to-use, large format reading of your speed. The
Speedometer module is also used to input your roll-out and pole count.

IMPORTANT: The Speedometer Module requires a telemetry module or a telemetry receiver and a brushless motor sensor.

1. Make sure the transmitter is off.

2. Remove the screw installed in the DX2E transmitter case as shown.

3. Remove the cover on the top of the radio using a small flat blade screw driver to gently pry it off.

4. Firmly seat the Speedometer Module into place and secure it with the screw removed in step 2.

For more information on the Speedomer Module visit www.spektrumrc.com

2. 3. 4.

4 SPEKTRUM DX2E ACTIVE USER GUIDE

2.4GHZ TROUBLESHOOTING GUIDE

Problem Possible Cause Solution

Your transmitter and receiver are too close together Move transmitter 1 to 3 meters from receiver

The system will
not connect

The receiver goes into
failsafe mode a short
distance away from the
transmitter

The receiver quits
responding during
operation

You are around metal objects Move to an area with less metal

The model selected is not the model bound to

Your transmitter was accidentally put into bind
mode and is no longer bound to your receiver

Check the receiver antenna to be sure it is not
cut or damaged

Inadequate battery voltage

Loose or damaged wires or connectors between
battery and receiver

Check model selected and ensure you are bound
to that model

Rebind your transmitter and receiver

Replace the receiver or contact Horizon Product Support
Make sure your receiver antenna is in an antenna

tube and is above the vehicle
Charge batteries. Spektrum receivers require at

least 3.5V to operate. An inadequate power supply
can allow voltage to momentarily drop below 3.5V
and cause the receiver to brown out and reconnect

Check the wires and connection between the battery
and receiver. Repair or replace wires and/or connectors

1-YEAR LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original
purchaser that the product purchased (the “Product”) will be
free from defects in materials and workmanship for a period of
1 year from the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i)
cosmetic damage, (ii) damage due to acts of God, accident,
misuse, abuse, negligence, commercial use, or due to
improper use, installation, operation or maintenance, (iii)
modifi cation of or to any part of the Product, (iv) attempted
service by anyone other than a Horizon Hobby authorized
service center, (v) Product not purchased from an authorized
Horizon dealer, (vi) Product not compliant with applicable
technical regulations or (vii) use that violates any applicable
laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON
MAKES NO OTHER WARRANTY OR REPRESENTATION, AND
HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT
THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF
THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive
remedy shall be that Horizon will, at its option, either (i)
service, or (ii) replace, any Product determined by Horizon to
be defective. Horizon reserves the right to inspect any and all
Product(s) involved in a warranty claim. Service or replacement
decisions are at the sole discretion of Horizon. Proof of
purchase is required for all warranty claims. SERVICE OR
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY
OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Further, in no event shall the liability of Horizon exceed the
individual price of the Product on which liability is asserted.
As Horizon has no control over use, setup, fi nal assembly,
modifi cation or misuse, no liability shall be assumed nor
accepted for any resulting damage or injury. By the act of use,
setup or assembly, the user accepts all resulting liability. If you
as the purchaser or user are not prepared to accept the liability
associated with the use of the Product, purchaser is advised to
return the Product immediately in new and unused condition to
the place of purchase.

Law

These terms are governed by Illinois law (without regard to
confl ict of law principals). This warranty gives you specifi c legal
rights, and you may also have other rights which vary from
state to state. Horizon reserves the right to change or modify
this warranty at any time without notice.

WARRANTY SERVICES
Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot
provide warranty support or service. Once assembly, setup or
use of the Product has been started, you must contact your
local distributor or Horizon directly. This will enable Horizon to
better answer your questions and service you in the event that
you may need any assistance. For questions or assistance,
please visit our website at www.horizonhobby.com, submit a
Product Support Inquiry, or call the toll free telephone number
referenced in the Warranty and Service Contact Information
section to speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant
in the country you live and use the Product in, please use the
Horizon Online Service Request submission process found on
our website or call Horizon to obtain a Return Merchandise

EN

SPEKTRUM DX2E ACTIVE USER GUIDE

5

EN

Authorization (RMA) number. Pack the Product securely using a
shipping carton. Please note that original boxes may be included,
but are not designed to withstand the rigors of shipping without
additional protection. Ship via a carrier that provides tracking
and insurance for lost or damaged parcels, as Horizon is not
responsible for merchandise until it arrives and is accepted
at our facility. An Online Service Request is available at http://
www.horizonhobby.com/content/service-center_render-service­center. If you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions
for submitting your product for service. When calling Horizon,
you will be asked to provide your complete name, street address,
email address and phone number where you can be reached
during business hours. When sending product into Horizon,
please include your RMA number, a list of the included items,
and a brief summary of the problem. A copy of your original sales
receipt must be included for warranty consideration. Be sure
your name, address, and RMA number are clearly written on the
outside of the shipping carton.

NOTICE: Do not ship LiPo batteries to Horizon. If you
have any issue with a LiPo battery, please contact the
appropriate Horizon Product Support offi ce.

Warranty Requirements

For Warranty consideration, you must include your original
sales receipt verifying the proof-of-purchase date. Provided
warranty conditions have been met, your Product will be
serviced or replaced free of charge. Service or replacement
decisions are at the sole discretion of Horizon.

Non-Warranty Service
Should your service not be covered by warranty, service

will be completed and payment will be required without
notifi cation or estimate of the expense unless the
expense exceeds 50% of the retail purchase cost. By

submitting the item for service you are agreeing to payment of
the service without notifi cation. Service estimates are available
upon request. You must include this request with your item
submitted for service. Non-warranty service estimates will
be billed a minimum of ½ hour of labor. In addition you will
be billed for return freight. Horizon accepts money orders
and cashier’s checks, as well as Visa, MasterCard, American
Express, and Discover cards. By submitting any item to Horizon
for service, you are agreeing to Horizon’s Terms and Conditions
found on our website http://www.horizonhobby.com/content/
service-center_render-service-center.

ATTENTION: Horizon service is limited to Product
compliant in the country of use and ownership.
If received, a non-compliant Product will not be
serviced. Further, the sender will be responsible for
arranging return shipment of the un-serviced Product,
through a carrier of the sender’s choice and at the
sender’s expense. Horizon will hold non-compliant
Product for a period of 60 days from notifi cation, after
which it will be discarded.

WARRANTY AND SERVICE CONTACT INFORMATION

Country of Purchase Horizon Hobby Contact Information Address

United States of
America

European Union

Horizon Service Center
(Repairs and Repair Requests)

Horizon Product Support
(Product Technical Assistance)

Sales

Horizon Technischer Service [e-mail]

Sales: Horizon Hobby GmbH [phone]

servicecenter.horizonhobby.com/RequestForm/

[e-mail]
877-504-0233
[e-mail]
800-338-4639

4105 Fieldstone Rd
Champaign, Illinois, 61822 USA

Hanskampring 9
D 22885 Barsbüttel, Germany

10-15

6 SPEKTRUM DX2E ACTIVE USER GUIDE

FCC INFORMATION

FCC ID: BRWDX2EQ2UC
FCC ID: BRWDASRX18

This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions:
This device may not cause harmful interference.

This device must accept any interference received, including

interference that may cause undesired operation.

CAUTION: Changes or modifi cations not expressly
approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless
technology which has been tested and found to be compliant
with the applicable regulations governing a radio transmitter
in the 2.400GHz to 2.4835GHz frequency range.

IC INFORMATION

IC: 6157A-DX2EQ2UC
IC: 6157 A-ASRX18

This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, Including interfer­ence that may cause undesired operation of the device.

Antenna Separation Distance

When operating your Spektrum transmitter, please be sure
to maintain a separation distance of at least 5 cm between
your body (excluding fi ngers, hands, wrists, ankles and feet)
and the antenna to meet RF exposure safety requirements as
determined by FCC regulations.

The illustrations show the
approximate 20 cm RF exposure
area and typical hand placement
when operating your Spektrum
transmitter.

20 cm

EN

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other
relevant provisions of the RED Directive.

A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their
waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling, please contact your local city offi ce, your
household waste disposal service or where you purchased the product.

55223.1

SPM2335
Created: 6/2017
© 2017 Horizon Hobby, LLC.
DSM, DSM2, DSMR, AVC, Active Vehicle Control and the
Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
All other trademarks, service marks and logos are property of their respective owners.
US 9,320,977. Other patents pending.

SPEKTRUM DX2E ACTIVE USER GUIDE

7

DE

HINWEIS

Alle Anweisungen, Garantien und dazugehörigen Dokumente können ohne Ankündigung von Horizon Hobby LLC
geändert werden. Eine aktuelle Version ersehen Sie bitte im Support Feld unter: http://www.horizonhobby.com

ERKLÄRUNG DER BEGRIFFE

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe
Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:

HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND
geringe oder keine Gefahr von Verletzungen ergeben.

ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden
UND die Gefahr von schweren Verletzungen.

WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,
Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberfl ächliche Verletzungen.

Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den
Produktfunktionen vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden

am Produkt oder persönlichem Eigentum führen oder schwere Verletzungen verursachen.
Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug. Dies ist ein hochentwickeltes Hobby-

Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben werden und benötigt gewisse
mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und verantwortungsvolle Weise
betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten führen. Dieses
Produkt eignet sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines Erwachsenen.
Verwenden Sie das Produkt nicht mit inkompatiblen Komponenten oder verändern / gebrauchen es ausserhalb
der Anweisungen von Horizon Hobby. Diese Bedienungsanleitung enthält Anweisungen für Sicherheit, Betrieb
und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung alle Anweisungen
und Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben werden
kann und Schäden oder schwere Verletzungen vermieden werden.

WARNUNG ZU GEFÄLSCHTEN PRODUKTEN: Bitte kaufen Sie Ihre Spektrum Produkte immer von einem

autorisiertem Händler um sicherzu stellen, dass Sie ein authentisches hochqualitatives original Spektrum
Produkt gekauft haben. Horizon Hobby lehnt jede Unterstützung, Service oder Garantieleistung von gefälschten
Produkten oder Produkten ab die von sich in Anspruch nehmen kompatibel mit Spektrum oder DSM zu sein.

HINWEIS: Dieses Produkt ist ausschließlich für die Verwendung in unbemannten ferngesteuerten Fahrzeugen
im Hobbybereich vorgesehen. Horizon Hobby lehnt jede Haftung und Garantieleistung ausserhalb der
vorgesehen Verwendung ab.

Garantieregistrierung: Registrieren Sie bitte heute Ihr Produkt unter www.spektrumrc.com/registration.

SICHERHEITSHINWEISE

• Bitte stellen Sie vor der Nutzung des Modells sicher, dass alle
Akkus vollständig geladen sind.

• Prüfen Sie stets alle Servos und ihre Verbindungen vor jedem Lauf.

• Betreiben Sie ihr Modell niemals in der Nähe von Zuschauern,
Parkplätzen oder jedem anderen Ort an dem Menschen verletzt
oder Eigentum beschädigt werden kann.

• Betreiben Sie ihr Modell niemals bei widrigen
Wetterbedingungen. Schlechte Sicht kann zu Desorientierung
und Kontrollverlust des Modells führen.

• Zielen Sie niemals mit der Antenne direkt auf das Modell. Die
Abstrahlung von der Antennenspitze ist gering.

• Sollten Sie zu irgendeinem beliebigen Zeitpunkt eine falsche oder
abnormale Reaktion des Modells beobachten, beenden Sie sofort
den Betrieb bis die Ursache dafür gefunden und korrigiert wurde.

EINSETZEN DER SENDERBATTERIEN

ACHTUNG: Bei Ersatz des Akkus durch einen

ungeeigneten Akkutyp besteht Explosionsgefahr. Entsorgen

Sie aufgebrauchte Akkus nach landesrechtlichen Vorschriften.

ACHTUNG: Wenn Sie wiederaufl adbare Batterien

verwenden, laden Sie nur diese auf. Das Laden nicht
wiederaufl adbarer Batterien kann zu Explosion führen und
dadurch Verletzungen und/oder Sachschäden verursachen.

8 SPEKTRUM DX2E ACTIVE USER GUIDE

AKKUSTATUS INDIKATOR

Grün Batterie ist OK (über 4V)
Grün blinkt Batteriespannung ist kritisch

niedrig. Ersetzen Sie die
Batterien. (unter 4 Volt)

EMPFÄNGER KOMPATIBILITÄT

Die DX2E ist kompatibel mit allen Spektrum DSMR und DSM2
Empfängern.

EMPFÄNGEREINBAU UND
ANSCHLÜSSE

Antenne

Anschluss Gasservo/Regler
Anschluss Lenkservo
Bindestecker

TYPISCHER ELEKTROEINBAU

Akku

Empfänger

Lenkservo

TYPISCHER VERBRENNEREINBAU

Empfänger

Zum Motor

Elektronischer
Fahrtenregler

Gasservo

Lenkservo

Akku

DE

BINDEN DES EMPFÄNGERS

Binden ist der Prozess der Programmierung des Empfänger
mit dem eindeutigen Signal eines spezifischen Senders
(GUID). Ist der Empfänger an den Sender gebunden, wird nur
er auf die Signale des Senders reagieren. Die DX2E und der
SR310 sind ab Werk gebunden. Sollten Sie diese neu binden
wollen folgen Sie bitte dieses Schritten:

1. Stecken Sie mit ausgeschalteten Empfänger den
Bindestecker in den Bindeanschluß des Empfängers.

2. Schalten Sie den Empfänger durch einen beliebigen
anderen Anschluß ein. Die grüne LED blinkt und zeigt
damit den Binde Mode an.

3. Mit dem Gashebel und Lenkrad in den gewünschten
Preset Failsafepositionen (siehe dazu den Abschnitt
Failsafe auf dieser Seite) drücken und halten Sie den
Bindeknopf gedrückt und schalten den Sender ein.
Die grüne LED auf der Vorderseite des Senders blinkt
innerhalb von drei Sekunden und zeigt damit an, dass
sich der Sender im Bindemode befindet. Lassen Sie
den Knopf los wenn die grüne LED blinkt. Halten Sie die
Failsafepositionen bis der Bindevorgang durchgeführt ist.

Bind Button

4. Die LED auf dem Empfänger leuchtet und zeigt damit an,
dass Sender und Empfänger gebunden sind.

5. Nehmen Sie den Bindestecker aus dem Bindeport
herraus und heben ihn sorgfältig auf.

Sie müssen den Bindevorgang wiederholen wenn:

• Sie andere Failsafepositionen wünschen, oder wenn
die Gas- oder Lenkfunktion reversiert wurden.

• Wechsel der Empfängers von DSM2, DSMR oder
Empfänger.

• Sie den Empfänger an einen anderen Sender binden.

FAILSAFE

Die Failsafepositionen werden während des Bindes eingestellt.
In dem unvorhergesehenden Fall, dass die RF Verbindung
unterbrochen wird, fährt der Empfänger die Servos in die
vorprogrammierten Failsafepositionen. Sollte der Empfänger
vor dem Sender eingeschaltet werden geht der Empfänger in
den Failsafemode. Wird dann der Sender eingeschaltet haben,
Sie wieder normale Kontrolle über das Modell. Für mehr
Informationen über das Einstellen der Faisafepositionen sehen
Sie bitte im Abschnitt-Binden des Empfänger nach.

Befestigen Sie den Empfänger mit doppelseitigen
Schaumklebeband. Das Klebeband hält den Empfänger
in Position und schützt ihn vor Vibrationen. Schieben Sie
die Antenne in ein Antennenröhrchen und stellen dieses
aufrecht. Je höher die Antenne steht, desto besser wird sie
das Signal empfangen.

ACHTUNG: Schneiden oder kürzen Sie die Antenne
nicht.

SPEKTRUM DX2E ACTIVE USER GUIDE

9